scholarly journals Numerical Simulation of Turbulent Steel Cem® Mold Under High Mass Flow Condition

2018 ◽  
Vol 424 ◽  
pp. 012033
Author(s):  
J.Y. Hwang ◽  
M.J. Cho ◽  
B.G. Thomas ◽  
S.M. Cho
Keyword(s):  
Numerical Simulation ◽  
Mass Flow ◽  
Flow Condition ◽  
High Mass

Numerical Simulation of the Performance of an Axial Compressor Operating With Supercritical Carbon Dioxide

2018 ◽  
Author(s):  
Jinlan Gou ◽  
Wei Wang ◽  
Can Ma ◽  
Yong Li ◽  
Yuansheng Lin ◽  
...  
Keyword(s):  
Carbon Dioxide ◽  
Numerical Simulation ◽  
Supercritical Carbon Dioxide ◽  
Critical Point ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Axial Compressor ◽  
Brayton Cycle ◽  
Supercritical Carbon

Using supercritical carbon dioxide (SCO2) as the working fluid of a closed Brayton cycle gas turbine is widely recognized nowadays, because of its compact layout and high efficiency for modest turbine inlet temperature. It is an attractive option for geothermal, nuclear and solar energy conversion. Compressor is one of the key components for the supercritical carbon dioxide Brayton cycle. With established or developing small power supercritical carbon dioxide test loop, centrifugal compressor with small mass flow rate is mainly investigated and manufactured in the literature; however, nuclear energy conversion contains more power, and axial compressor is preferred to provide SCO2 compression with larger mass flow rate which is less studied in the literature. The performance of the axial supercritical carbon dioxide compressor is investigated in the current work. An axial supercritical carbon dioxide compressor with mass flow rate of 1000kg/s is designed. The thermodynamic region of the carbon dioxide is slightly above the vapor-liquid critical point with inlet total temperature 310K and total pressure 9MPa. Numerical simulation is then conducted to assess this axial compressor with look-up table adopted to handle the nonlinear variation property of supercritical carbon dioxide near the critical point. The results show that the performance of the design point of the designed axial compressor matches the primary target. Small corner separation occurs near the hub, and the flow motion of the tip leakage fluid is similar with the well-studied air compressor. Violent property variation near the critical point creates troubles for convergence near the stall condition, and the stall mechanism predictions are more difficult for the axial supercritical carbon dioxide compressor.

Leakage flow analysis in the gas turbine shroud gap

2019 ◽  
Vol 91 (8) ◽  
pp. 1077-1085 ◽  
Author(s):  
Filip Wasilczuk ◽  
Pawel Flaszynski ◽  
Piotr Kaczynski ◽  
Ryszard Szwaba ◽  
Piotr Doerffer ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Gas Turbine ◽  
Mass Flow ◽  
Labyrinth Seal ◽  
Leakage Flow ◽  
Original Design ◽  
Reference Case ◽  
Content Type ◽  
Flow Through ◽  
The Impact

Purpose The purpose of the study is to measure the mass flow in the flow through the labyrinth seal of the gas turbine and compare it to the results of numerical simulation. Moreover the capability of two turbulence models to reflect the phenomenon will be assessed. The studied case will later be used as a reference case for the new, original design of flow control method to limit the leakage flow through the labyrinth seal. Design/methodology/approach Experimental measurements were conducted, measuring the mass flow and the pressure in the model of the labyrinth seal. It was compared to the results of numerical simulation performed in ANSYS/Fluent commercial code for the same geometry. Findings The precise machining of parts was identified as crucial for obtaining correct results in the experiment. The model characteristics were documented, allowing for its future use as the reference case for testing the new labyrinth seal geometry. Experimentally validated numerical model of the flow in the labyrinth seal was developed. Research limitations/implications The research studies the basic case, future research on the case with a new labyrinth seal geometry is planned. Research is conducted on simplified case without rotation and the impact of the turbine main channel. Practical implications Importance of machining accuracy up to 0.01 mm was found to be important for measuring leakage in small gaps and decision making on the optimal configuration selection. Originality/value The research is an important step in the development of original modification of the labyrinth seal, resulting in leakage reduction, by serving as a reference case.

scholarly journals Design & Development of a High Mass Flow Piston Synthetic Jet Actuator

2015 ◽  
Vol 92 ◽  
pp. 02002 ◽  
Author(s):  
Hamad Muhammad Ashraf ◽  
Karthika Murugan Illikkal ◽  
Francis D'souza ◽  
Mohamed Alsayed Mahmood ◽  
Suhail Mahmud Mostafa ◽  
...  
Keyword(s):  
Mass Flow ◽  
Synthetic Jet ◽  
High Mass ◽  
Design Development ◽  
Synthetic Jet Actuator

scholarly journals Simulation and Modeling of Flow in a Gas Compressor

2015 ◽  
Vol 2015 ◽  
pp. 1-7
Author(s):  
Anna Avramenko ◽  
Alexey Frolov ◽  
Jari Hämäläinen
Keyword(s):  
Steady State ◽  
Mass Flow ◽  
Gas Flow ◽  
Simulation Method ◽  
High Mass ◽  
Ansys Fluent ◽  
Flow Rates ◽  
Mass Flow Rates ◽  
Low Mass ◽  
Flow Through

The presented research demonstrates the results of a series of numerical simulations of gas flow through a single-stage centrifugal compressor with a vaneless diffuser. Numerical results were validated with experiments consisting of eight regimes with different mass flow rates. The steady-state and unsteady simulations were done in ANSYS FLUENT 13.0 and NUMECA FINE/TURBO 8.9.1 for one-period geometry due to periodicity of the problem. First-order discretization is insufficient due to strong dissipation effects. Results obtained with second-order discretization agree with the experiments for the steady-state case in the region of high mass flow rates. In the area of low mass flow rates, nonstationary effects significantly influence the flow leading stationary model to poor prediction. Therefore, the unsteady simulations were performed in the region of low mass flow rates. Results of calculation were compared with experimental data. The numerical simulation method in this paper can be used to predict compressor performance.

Aerodynamic Performance Evaluation of Axial Flow Fan Using Numerical Techniques

2021 ◽  
Author(s):  
Raghuvaran D. ◽  
Satvik Shenoy ◽  
Srinivas G
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Rotational Speed ◽  
Total Pressure ◽  
Axial Flow ◽  
High Mass ◽  
Ansys Fluent ◽  
Industrial Sectors ◽  
Mass Flow Rates

Abstract Axial flow fans (AFF) are extensively used in various industrial sectors, usually with flows of low resistance and high mass flow rates. The blades, the hub and the shroud are the three major parts of an AFF. Various kinds of optimisation can be implemented to improve the performance of an AFF. The most common type is found to be geometric optimisation including variation in number of blades, modification in hub and shroud radius, change in angle of attack and blade twist, etc. After validation of simulation model and carrying out a grid independence test, parametric analysis was done on an 11-bladed AFF with a shroud of uniform radius using ANSYS Fluent. The rotational speed of the fan and the velocity at fan inlet were the primary variables of the study. The variation in outlet mass flow rate and total pressure was studied for both compressible and incompressible ambient flows. Relation of mass flow rate and total pressure with inlet velocity is observed to be linear and exponential respectively. On the other hand, mass flow rate and total pressure have nearly linear relationship with rotational speed. A comparison of several different axial flow tracks with the baseline case fills one of the research gaps.

Design and Testing of a Can Combustor for a Small Gas Turbine Application

2013 ◽  
Author(s):  
K. V. L. Narayana Rao ◽  
N. Ravi Kumar ◽  
G. Ramesha ◽  
M. Devathathan
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Gas Turbines ◽  
Pressure Loss ◽  
High Energy ◽  
Experimental Results ◽  
High Mass ◽  
Test Facility ◽  
Design Requirements

Can type combustors are robust, with ease of design, manufacturing and testing. They are extensively used in industrial gas turbines and aero engines. This paper is mainly based on the work carried out in designing and testing a can type combustion chamber which is operated using JET-A1 fuel. Based on the design requirements, the combustor is designed, fabricated and tested. The experimental results are analysed and compared with the design requirements. The basic dimensions of the combustor, like casing diameter, liner diameter, liner length and liner hole distribution are estimated through a proprietary developed code. An axial flow air swirler with 8 vanes and vane angle of 45 degree is designed to create a re-circulation zone for stabilizing the flame. The Monarch 4.0 GPH fuel nozzle with a cone angle of 80 degree is used. The igniter used is a high energy igniter with ignition energy of 2J and 60 sparks per minute. The combustor is modelled, meshed and analysed using the commercially available ansys-cfx code. The geometry of the combustor is modified iteratively based on the CFD results to meet the design requirements such as pressure loss and pattern factor. The combustor is fabricated using Ni-75 sheet of 1 mm thickness. A small combustor test facility is established. The combustor rig is tested for 50 Hours. The experimental results showed a blow-out phenomenon while the mass flow rate through the combustor is increased beyond a limit. Further through CFD analysis one of the cause for early blow out is identified to be a high mass flow rate through the swirler. The swirler area is partially blocked and many configurations are analysed. The optimum configuration is selected based on the flame position in the primary zone. The change in swirler area is implemented in the test model and further testing is carried out. The experimental results showed that the blow-out limit of the combustor is increased to a good extent. Hence the effect of swirler flow rate on recirculation zone length and flame blow out is also studied and presented. The experimental results showed that the pressure loss and pattern factor are in agreement with the design requirements.

Adiabatic Capillary Tube Model for a Carbon Dioxide Transcritical Cycle

2015 ◽  
Vol 23 (02) ◽  
pp. 1550011 ◽  
Author(s):  
R. O. Nunes ◽  
R. N. Faria ◽  
N. Bouzidi ◽  
L. Machado ◽  
R. N. N. Koury
Keyword(s):  
Experimental Data ◽  
Carbon Dioxide ◽  
Mathematical Model ◽  
Mass Flow ◽  
Flow Condition ◽  
Capillary Tube ◽  
Tube Model ◽  
Minimum Diameter ◽  
Conservation Of Energy ◽  
Capillary Tube Model

This paper presents a mathematical model for a capillary tube using CO 2 as fluid in steady flow transcritical cycle. The capillary tube is divided into N volumes controls and the model is based on applying the equations of conservation of energy, mass and momentum in the fluid in each of these volumes controls. The model calculates the mass flow of the CO 2 in the capillary tube as a function of CO 2 pressures at the inlet and outlet of the capillary and the temperature of CO 2 at the input of this device. The capillary tube is considered to be adiabatic, and the limit of operation due to blocked flow condition is also considered in the model. The validation of the model was performed with experimental data and the results showed that the model is capable of predicting the mass flow in the capillary tube with errors less than 10%. The model was also used to determine the minimum diameter of the capillary tube for various conditions of CO 2 transcritical cycle.

Computational Fluid Dynamics Performance Estimation of Turbo Booster Vacuum Pump

2003 ◽  
Vol 125 (3) ◽  
pp. 586-589 ◽  
Author(s):  
H.-P. Cheng ◽  
C.-J. Chen , ◽  
P.-W. Cheng ,
Keyword(s):  
Fluid Dynamics ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Vacuum Pump ◽  
Performance Estimation ◽  
High Mass ◽  
Rotor Speed ◽  
Low Mass ◽  
Pump Inlet

The CFD performance estimation of turbo booster vacuum pump shows the axial vortex and back flow is evident when the mass flow rate is increased. The pressure is increased from the pump inlet to the outlet for the low mass flow rate cases. But for high mass flow rate cases, the pressure is increased until the region near the end of the rotor then decreased. The calculated inlet pressure, compression ratio, and pumping speed is increased, decreased, and decreased, respectively, when the mass flow rate is increased. The pumping speed is increased when the rotor speed is increased.

Sign in / Sign up

Export Citation Format

Share Document