Performance behavior of pocketed journal bearing employing non-newtonian lubricant

2021 ◽  
Vol 3 (4) ◽  
pp. 045013
Author(s):  
Vivek Bhardwaj
Keyword(s):  
Coefficient Of Friction ◽  
Power Law ◽  
Carrying Capacity ◽  
Shear Thickening ◽  
Numerical Approach ◽  
Load Carrying Capacity ◽  
Shear Thickening Fluid ◽  
Load Carrying ◽  
Power Law Index ◽  
Performance Behavior

Abstract This paper reports the improvement in the performance behaviors of non-Newtonian fluid lubricated journal bearings employing a rectangular pocket. Coefficient of friction and load carrying capacity of pocketed and non-pocketed bearings are reported and discussed. In the numerical approach, non-Newtonian behavior of lubricant is simulated employing the power law model. Various cases of bearings having different axial length to diameter ratios [(L/D) in the range 0.5–2.0] are considered. Lubricants of different rheology viz. pseudoplastic, Newtonian and shear thickening were employed for lubricating the bearings. Rheology of lubricant is controlled by varying the power law index n in the range 0.9–1.1. Based on the investigation, it is found that the pocketed bearing yields significantly reduced coefficient of friction and higher load carrying capacity in comparison to the non-pocketed bearing. Also, the performance of pocketed bearing improves with the increase in the power law index. Best performance of the pocketed bearing is observed for the bearing having L/D value of 0.5 at high eccentricity ratio when lubricated with the shear thickening fluid (n=1.1).

Steady-state performance of a circular journal bearing lubricated with a non-Newtonian fluid considering the elastic deformation of the liner

2019 ◽  
Vol 233 (9) ◽  
pp. 1389-1396
Author(s):  
Boualem Chetti ◽  
Hamid Zouggar
Keyword(s):  
Friction Coefficient ◽  
Elastic Deformation ◽  
Power Law ◽  
Carrying Capacity ◽  
Reynolds Equation ◽  
Journal Bearing ◽  
Load Carrying Capacity ◽  
Static Characteristics ◽  
Load Carrying ◽  
Power Law Index

In this work, a numerical study of the effect of elastic deformation on the static characteristics of a circular journal bearing operating with non-Newtonian fluids obeying to the power law model is presented. The modified Reynolds equation has been derived taking into consideration the effect of non-Newtonian behavior of the fluids. To obtain the pressure distribution, the Reynolds equation has been solved using finite difference technique with appropriate iterative technique incorporating Reynolds boundary conditions. The static performance characteristics for finite-width journal bearing in terms of the load-carrying capacity, the attitude angle, friction coefficient, and the side leakage have been studied for various values of the non-Newtonian power law index n and the elastic coefficient. The results show that the increase of the power law index produces a higher load-carrying capacity, a higher side leakage, a lower attitude angle, and a lower friction coefficient. From this study, it can be concluded that the elastic deformation has an important influence on the static characteristics of the journal bearing lubricated with a non-Newtonian fluid, and this influence is more significant for the journal bearing operating at larger values of the eccentricity ratio.

scholarly journals Influence of Aspect Ratio on the Performance Characteristics of Plain Journal Bearing Lubricating With Non-Newtonian Lubricant

2019 ◽  
Vol 8 (6) ◽  
pp. 1022-1026
Keyword(s):  
Aspect Ratio ◽  
Power Law ◽  
Carrying Capacity ◽  
Journal Bearing ◽  
Performance Characteristics ◽  
Load Carrying Capacity ◽  
Aspect Ratios ◽  
Load Carrying ◽  
Static Performance ◽  
Power Law Index

This article presents the static performance characteristics of a plain journal bearing with non-Newtonian lubricant (power law) at different aspect ratio. Finite difference approach is employed to solve the modified Reynold equation. Hydrodynamic regime is assumed to be isothermal. The fluid film pressure is established using modified Reynold equation and Reynold boundary condition through iteratively. Thus the obtain pressure is used to find-out the performance characteristics for instance load carrying capacity, attitude angle, friction force and side leakage. Three aspect ratios are assumed 0.5, 1 and 1.5 for the present study. The effect of different aspect ratios on performance characteristics at different power law index (0.9, 1 and 1.1) has been presented.

Density Variation Effects in Stepped-Thrust Bearings

1959 ◽  
Vol 26 (3) ◽  
pp. 337-340
Author(s):  
C. F. Kettleborough
Keyword(s):  
Coefficient Of Friction ◽  
Carrying Capacity ◽  
Thrust Bearing ◽  
Density Variation ◽  
Load Carrying Capacity ◽  
Thrust Bearings ◽  
Load Carrying ◽  
The Coefficient Of Friction

Abstract The problem of the stepped-thrust bearing is considered but, whereas normally volumetric continuity is assumed, the equations are solved assuming mass continuity; i.e., the variation of density is also considered as well as the effect of the stepped discontinuity on the load-carrying capacity and the coefficient of friction. Computed theoretical curves illustrate the importance of the density on the operation of this bearing and, in part, explain results already published.

The effect of V-shape protruded and dimple textured on the load-carrying capacity and coefficient of friction of hydrodynamic journal bearing: A comparative numerical study

2020 ◽  
pp. 135065012093500
Author(s):  
Sanjay Sharma ◽  
Aniket Sharma ◽  
Gourav Jamwal ◽  
Rajeev Kumar Awasthi
Keyword(s):  
Coefficient Of Friction ◽  
Carrying Capacity ◽  
Performance Enhancement ◽  
Numerical Study ◽  
Geometrical Parameters ◽  
Load Carrying Capacity ◽  
Enhancement Ratio ◽  
Load Carrying ◽  
The Coefficient Of Friction ◽  
Computing Performance

The present comparative numerical study is between V-shape protruded, dimple textured, and untextured bearing. The performance parameters in terms of the load-carrying capacity and coefficient of friction are computed by solving governing Reynold’s equation of the lubricant fluid flow. The governing equation is solved by the finite element method by assuming that the fluid is Newtonian and isoviscous in nature. The effect of eccentricity ratios, texture distribution, texture heights, and texture depths are considered for the analysis in both textured bearings. From simulated results, the load-carrying capacity and coefficient of friction is found to be maximum for protruded textured bearing in full textured region and first half-textured region respectively as compared to untextured bearings. Finally, optimal operating and geometrical parameters of textured bearing is obtained by computing performance enhancement ratio, which is the ratio of the load-carrying capacity to the coefficient of friction. The maximum value of the performance enhancement ratio is found for protruded and dimple textured bearing in full texturing and second half-region corresponding to the eccentricity ratio of 0.8 and 0.6 respectively at texture height and depth of 0.4.

scholarly journals A STUDY OF FERROFLUID LUBRICATION BASED ROUGH SINE FILM SLIDER BEARING WITH ASSORTED POROUS STRUCTURE

2019 ◽  
Vol 59 (2) ◽  
pp. 144-152
Author(s):  
Mohmmadraiyan M. Munshi ◽  
Ashok R. Patel ◽  
Gunamani B. Deheri
Keyword(s):  
Porous Structure ◽  
Carrying Capacity ◽  
Graphical Representation ◽  
Negative Impact ◽  
Positive Impact ◽  
Numerical Approach ◽  
Load Carrying Capacity ◽  
Slider Bearing ◽  
Load Carrying ◽  
The Impact

This paper attempts to study a ferrofluid lubrication based rough sine film slider bearing with assorted porous structure using a numerical approach. The fluid flow of the system is regulated by the Neuringer-Rosensweig model. The impact of the transverse surface roughness of the system has been derived using the Christensen and Tonder model. The corresponding Reynolds’ equation has been used to calculate the pressure distribution which, in turn, has been the key to formulate the load carrying capacity equation. A graphical representation is made to demonstrate the calculated value of the load carrying capacity which is a dimensionless unit. The numbers thus derived have been used to prove that ferrofluid lubrication aids the load carrying capacity. The study suggests that the positive impact created by magnetization in the case of negatively skewed roughness helps to partially nullify the negative impact of the transverse roughness. Further investigation implies that when the Kozeny-Carman’s model is used, the overall performance is enhanced. The Kozeny-Carman’s model is a form of an empirical equation used to calculate permeability that is dependent on various parameters like pore shape, turtuosity, specific surface area and porosity. The success of the model can be accredited to its simplicity and efficiency to describe measured permeability values. The obtained equation was used to predict the permeability of fibre mat systems and of vesicular rocks.

Partially Textured Slider and Journal Bearing Analysis

2012 ◽  
Vol 58 (2) ◽  
Author(s):  
T. V. V. L. N. Rao ◽  
A. M. A. Rani ◽  
T. Nagarajan ◽  
F. M. Hashim
Keyword(s):  
Friction Coefficient ◽  
Coefficient Of Friction ◽  
Carrying Capacity ◽  
Journal Bearing ◽  
Load Capacity ◽  
Load Carrying Capacity ◽  
Load Carrying ◽  
Bearing Analysis

The present study examines the influence of partial texturing of bearing surfaces on improvement in load capacity and reduction in friction coefficient for slider and journal bearing. The geometry of partially textured slider and journal bearing considered in this work composed of a number of successive regions of groove and land configurations. The nondimensional pressure expressions for the partially textured slider and journal bearing are derived taking into consideration of texture geometry and extent of partial texture. Partial texturing has a potential to generate load carrying capacity and reduce coefficient of friction, even for nominally parallel bearing surfaces.

scholarly journals Application of topological optimisation methodology to hydrodynamic thrust bearings

2020 ◽  
pp. 135065012097259
Author(s):  
Kalle Kalliorinne ◽  
Roland Larsson ◽  
Andreas Almqvist
Keyword(s):  
Coefficient Of Friction ◽  
Carrying Capacity ◽  
Friction Torque ◽  
Shape Optimisation ◽  
Load Carrying Capacity ◽  
Thrust Bearings ◽  
Aspect Ratios ◽  
Load Carrying ◽  
The Coefficient Of Friction ◽  
Moving Asymptotes

The bearing geometry has a big impact on the performance of a hydrodynamic thrust bearing. For this reason, shape optimisation of the bearing surface has been carried out for some time, with Lord Rayleigh’s early publication dated back to 1918. There are several recent results e.g. optimal bearing geometries that maximise the load carrying capacity for hydrodynamic thrust bearings. Currently, many engineers are making an effort to include sustainability in their work, which increases the need for bearings with lower friction and higher load carrying capacity. Improving these two qualities will result in lower energy consumption and increase the lifetime of applications, which are outcomes that will contribute to a sustainable future. For this reason, there is a need to find geometries that have performance characteristics of as low coefficient of friction torque as possible. In this work, the topological optimisation method of moving asymptotes is employed to optimise bearing geometries with the objective of minimising the coefficient of friction torque. The results are both optimised bearing geometries that minimise the coefficient of friction torque and bearing geometries that maximise the load carrying capacity. The bearing geometries are of comparable aspect ratios to the ones uses in recent publications. The present article also covers minimisation of friction torque on ring bearing geometries, also known as thrust washers. The results are thrust washers with periodical geometries, where the number of periodical segments has a high impact on the geometrical outcome.

Performance investigation of micro-pocketed textured pad thrust bearing

2018 ◽  
Vol 70 (8) ◽  
pp. 1388-1395 ◽  
Author(s):  
Shipra Aggarwal ◽  
R.K. Pandey
Keyword(s):  
Coefficient Of Friction ◽  
Cross Sections ◽  
Carrying Capacity ◽  
Thrust Bearing ◽  
Load Carrying Capacity ◽  
Temperature Relation ◽  
Cross Sectional ◽  
Content Type ◽  
Load Carrying ◽  
Coupled Solution

Purpose The purpose of this paper is to conceive a new surface texture incorporating a tiny shape among the micro-pockets (with circular, rectangular, trapezoidal and triangular cross-sections) and dimples (cylindrical, hemispherical and ellipsoidal) for exploring to enhance the maximum possible performance behaviors of sector shape pad thrust bearing. Design/methodology/approach Numerical simulation of hydrodynamically lubricated sector shape textured pad thrust bearing has been presented incorporating thermal and cavitation effects. The coupled solution of governing equations (Reynolds equation, film thickness expression, viscosity–temperature relation, energy equation and Laplace equation) has been achieved using finite difference method and Gauss–Seidel iterative scheme. Findings With new textured pads, higher load-carrying capacity and lower coefficient of friction are obtained in comparison to plain sector shape pad. Texture pattern comprising square cross-sectional pockets yields higher load-carrying capacity and lower coefficient of friction in comparison to other cross-sectional shapes (circular, trapezoidal and triangular) of pockets considered herein. Originality/value This study reports a new texture, which involves micro-pockets of square cross-sectional shapes to improve the performance behavior of sector shape pad thrust bearing. About 75 per cent increase in load carrying capacity and 42 per cent reduction in coefficient of friction have been achieved with pad having new texture in comparison to conventional pad.

scholarly journals Antifriction and Antiwear Effect of Lamellar ZrS2 Nanobelts as Lubricant Additives

Nanomaterials ◽  
2019 ◽  
Vol 9 (3) ◽  
pp. 329 ◽  
Author(s):  
Wei Tang ◽  
Chuang Yu ◽  
Shaogang Zhang ◽  
Songyong Liu ◽  
Xingcai Wu ◽  
...  
Keyword(s):  
Coefficient Of Friction ◽  
Carrying Capacity ◽  
Friction And Wear ◽  
Normal Load ◽  
Lubricant Additives ◽  
Load Carrying Capacity ◽  
Load Carrying ◽  
The Coefficient Of Friction ◽  
Wear Tests ◽  
Friction And Wear Tests

In this study, the tribological behavior of lamellar ZrS2 nanobelts as lubricant additives was investigated under different concentrations, normal load, velocity, and temperature. The friction and wear tests were performed using a tribometer and with a reciprocating motion. The results indicate that the lamellar ZrS2 nanobelt additives can effectively reduce the coefficient of friction and running-in time during the running-in period. With the addition of ZrS2, the wear volumes decrease significantly. The wear is mostly influenced by the tribological performance throughout the running-in period. The lower the running-in time and coefficient of friction are during the running-in period, the less amount of wear is shown. ZrS2 can significantly increase the load-carrying capacity of oil. The 1.0 wt% concentration of ZrS2 yields the best antifriction effect, antiwear performance, and load-carrying capacity. The ZrS2 additives can increase the working temperature of the oil. The friction-reducing and antiwear mechanisms of lamellar ZrS2 were discussed.

Influence of Yield Strength Variability over Cross-Section to Steel Beam Load-Carrying Capacity

2005 ◽  
Vol 10 (2) ◽  
pp. 151-160 ◽  
Author(s):  
J. Kala ◽  
Z. Kala
Keyword(s):  
Yield Strength ◽  
Cross Section ◽  
Carrying Capacity ◽  
Bending Moment ◽  
Statistical Characteristics ◽  
Load Carrying Capacity ◽  
Load Carrying ◽  
Strength Variability ◽  
Hot Rolled ◽  
Hot Rolled Steel

Authors of article analysed influence of variability of yield strength over cross-section of hot rolled steel member to its load-carrying capacity. In calculation models, the yield strength is usually taken as constant. But yield strength of a steel hot-rolled beam is generally a random quantity. Not only the whole beam but also its parts have slightly different material characteristics. According to the results of more accurate measurements, the statistical characteristics of the material taken from various cross-section points (e.g. from a web and a flange) are, however, more or less different. This variation is described by one dimensional random field. The load-carrying capacity of the beam IPE300 under bending moment at its ends with the lateral buckling influence included is analysed, nondimensional slenderness according to EC3 is λ¯ = 0.6. For this relatively low slender beam the influence of the yield strength on the load-carrying capacity is large. Also the influence of all the other imperfections as accurately as possible, the load-carrying capacity was determined by geometrically and materially nonlinear solution of very accurate FEM model by the ANSYS programme.

Sign in / Sign up

Export Citation Format

Share Document