The experimental optimization of abrasive wear resistance model for an in-situ AlB2/Al-4Cu metal matrix composite

2016 ◽  
Vol 68 (6) ◽  
pp. 632-639 ◽  
Author(s):  
Ferit Ficici
Keyword(s):  
Weight Loss ◽  
Abrasive Wear ◽  
Metal Matrix ◽  
Wear Behavior ◽  
Minimum Weight ◽  
Matrix Alloy ◽  
Content Type ◽  
Testing Conditions ◽  
Composite Samples

Purpose The paper aims to describe the Taguchi design method-based abrasive wear modeling of in situ AlB2 flake reinforced Al-4Cu matrix alloy composites. Design/methodology/approach The abrasive wear behaviors of the composite samples were investigated using pin-on-disk method where the samples slid against different sizes of SiC abrasive grits under various testing conditions. The orthogonal array, signal-to-noise (S/N) ratio and analysis of variance were used to study the optimal testing parameters on composite samples. Findings The weight loss of composites decreased with increasing grit size and percentage reinforcement and increased with increasing sliding speed. The optimum test condition, at which the minimum weight loss is obtained, has been determined to be A3B3C1 levels of the control factors. Deviations between the actual and the predicted S/N ratios for abrasive weight losses are negligibly small with 99.5 per cent confidence level. Originality/value This paper fulfils an identification of Taguchi method-based abrasive wear behavior of AlB2/Al-4Cu metal matrix composites produced by squeeze casting under various testing conditions.

Abrasive wear analysis of RZ5/TiC in-situ composites: a statistical approach

2019 ◽  
Vol 71 (9) ◽  
pp. 1029-1037
Author(s):  
Deepak Mehra ◽  
Manas Mohan Mahapatra ◽  
Suraj Prakash Harsha
Keyword(s):  
Weight Loss ◽  
Statistical Analysis ◽  
Abrasive Wear ◽  
Coefficient Of Friction ◽  
Control Parameters ◽  
Content Type ◽  
Wear Analysis ◽  
Full Factorial ◽  
Sliding Distance

Purpose The RZ5 mg alloy is used in automotive and aerospace applications including helicopter gearboxes and aircraft components. These components are prone to the wear as per the demands. The present work is the study of the significance of hard particle/ceramic, i.e. titanium carbide (TiC) in RZ5 mg alloy to protect the machine components from wear. Design/methodology/approach The abrasive wear analysis of in-situ RZ5-TiC magnesium matrix composite is considered for the study. The primary focus of the present work is to analyze the effects of varying control parameters, i.e. Wt.% of TiC, sliding distance and applied load on the responses, i.e. weight loss and coefficient of friction. Full factorial design of the experiment based on statistical analysis is used. Findings It is observed that the individually Wt.% of TiC and sliding distance show the comparatively significant effect on both responses. Similarly, the interaction between sliding distance and Wt.% of TiC indicated the considerable impact on weight loss. The regression equations are developed and validated for estimating responses. It is observed that the percentage errors are not appearing more than 10 per cent of responses. Therefore, the close agreement between measured and predicted values shows the adequacy of the model. The control factor is optimized using multi-response optimization. The variations of the order of 2.47 and 2.35 per cent in target value of the coefficient of friction and weight loss are achieved. Originality/value The current manuscript provides a detailed abrasive wear statistical analysis of RZ5-TiC composite. The influence of control parameters on the responses using the full factorial design, the main effect plots and interaction effects are presented.

Effect of wear parameters on dry abrasive wear of RZ5-TiC in situ composite

2018 ◽  
Vol 70 (2) ◽  
pp. 256-263 ◽  
Author(s):  
Deepak Mehra ◽  
Manas Mohan Mahapatra ◽  
Suraj Prakash Harsha
Keyword(s):  
Weight Loss ◽  
Wear Resistance ◽  
Abrasive Wear ◽  
Coefficient Of Friction ◽  
Applied Load ◽  
Mg Alloy ◽  
Ceramic Particles ◽  
Content Type ◽  
Sliding Distance

Purpose The purpose of this study is to increase the wear resistance of Mg alloy by adding hard ceramic particles to it. The inclusion of hard ceramic particles further strengthen the Mg alloy, resulting in higher wear resistance. Mg alloys containing Zn, rare earth and Zr exhibit high specific strength and excellent creep resistance, making them suitable for aerospace components such as aircraft gearboxes and generator housings. Design/methodology/approach In the present study, composites have been produced in situ by using RZ5 mg alloy as matrix and TiC as reinforcement by self-propagating high-temperature synthesis technique. The abrasive wear behavior of RZ5 Mg alloy matrix reinforced with TiC particulates has also been examined. The pin-on-disc apparatus has been used for the tests. The abrasive paper is used as a counter body, and the results are obtained by changing sliding distance and applied load. Findings A notable enhancement in the wear resistance and mechanical properties of tested composite has been observed as compared to the RZ5 Mg alloy as a matrix. There is a uniform increment in the change in weight loss of RZ5-TiC composite with increasing sliding distance and applied load, but it decreases with increasing TiC content. The coefficient of friction (µ) also decreases uniformly with an increase in the reinforcement of TiC, but it decreases with an increase in applied load and sliding distance. The investigation of the worn composite, which determines dominant wear mechanisms as abrasion and plowing grooves on tested samples, has been done using field emission scanning electron microscopy. Originality/value The current manuscript provides a detailed abrasive wear analysis of RZ5-TiC composite by using different wear parameters. Specifically, extensive experimental data have been provided for RZ5-TiC composite. The effects of parameters such as applied load, sliding distance and Wt.% of TiC on the weight loss and coefficient of friction of the composites have been analyzed and discussed thoroughly.

Modeling the abrasive wear behavior of in-situ synthesized magnesium RZ5/TiB2 metal matrix composites

2021 ◽  
pp. 095440892110655
Author(s):  
Arabinda Meher ◽  
Manas Mohan Mahapatra ◽  
Priyaranjan Samal ◽  
Pandu R. Vundavilli
Keyword(s):  
Abrasive Wear ◽  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Tribological Behavior ◽  
Wear Behavior ◽  
Wear Test ◽  
Regression Equation ◽  
Matrix Composites ◽  
Worn Surface ◽  
Anova Technique

In the present study, the statistical analysis on tribological behavior of RZ5/TiB2 magnesium-based metal matrix composites is carried out using Taguchi design and analysis of variance (ANOVA) technique. Taguchi analysis using signal-to-noise ratio indicates that the sliding distance and wt.% TiB2 are the most significant factors in evaluating weight loss and coefficient of friction, respectively. The regression equation is formulated utilizing the ANOVA technique to study the output responses based on the input abrasive wear test experimental results. The regression equation is validated through a comprehensive study taking a series of abrasive wear tests and indicates the percentage deviation of regression modeling is in the range of ± 10%. The individual and combined effect of wear parameters on tribological behavior are investigated through the main effect plots and response surface plots. The micrograph of the worn surface of RZ5/TiB2 composites is studied using field emission scanning electron microscope (FESEM), indicating the formation of an oxide layer on the worn surface.

Fabrication and characterization of TiB2-reinforced functionally graded aluminum matrix material

2020 ◽  
Vol 72 (10) ◽  
pp. 1147-1152
Author(s):  
Ömer Savaş
Keyword(s):  
Wear Rate ◽  
Abrasive Wear ◽  
Peer Review ◽  
Centrifugal Force ◽  
Matrix Material ◽  
Aluminum Matrix ◽  
Functionally Graded ◽  
Aluminum Matrix Composites ◽  
Content Type

Purpose This study aims to investigate the production and abrasive wear rate of functionally graded TiB2/Al composites. TiB2 particles have been spontaneously formed in liquid matrix using in situ technique. The properties of composites such as hardness, abrasive wear rate and microstructure have been examined. Design/methodology/approach In situ TiB2 reinforcement phase was synthesized by using a liquid Al–Ti–B system. A semi-solid composite (Al(l)-TiB2(s)) prepared at 900°C was solidified under a centrifugal force to both grade functionally and give the final shape to materials. Abrasive wear test of materials was conducted using the pin-on-disk method at room temperature. The wear tests were carried out with two different loads of 1 Newton (N) and 2 N, a sliding velocity of 3.5 m s−1 and a sliding distance of 75 m. Findings This research provided the following findings; TiB2 particles can be successfully synthesized with in situ reaction technique in molten aluminum. It was determined that abrasive wear rate increases with increasing load and decreases with increasing TiB2 reinforcement content within matrix. Originality/value In previous studies, there have been many trials on the in situ production of TiB2-reinforced aluminum matrix composites. However, there are few studies on production of in situ TiB2-reinforced aluminum matrix functionally graded materials. At the same time, there is no study that the properties of composite, such as hardness and abrasive wear rate, are examined together according to centrifugal force. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-12-2019-0538/

Tribological behavior of AA7075-TiC composites by powder metallurgy

2018 ◽  
Vol 70 (6) ◽  
pp. 1066-1071 ◽  
Author(s):  
Saravanan C. ◽  
Subramanian K. ◽  
Anandakrishnan V. ◽  
Sathish S.
Keyword(s):  
Powder Metallurgy ◽  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Tribological Behavior ◽  
Wear Behavior ◽  
Process Condition ◽  
Wear Test ◽  
Matrix Composites ◽  
Content Type ◽  
Weight Percentage

Purpose Aluminium is the most preferred material in engineering structural components because of its excellent properties. Furthermore, the properties of aluminium may be enhanced through metal matrix composites and an in-depth investigation on the evolved properties is needed in view of metallurgical, mechanical and tribological aspects. The purpose of this study is to explore the effect of TiC addition on the tribological behavior of aluminium composites. Design/methodology/approach Aluminium metal matrix composites at different weight percentage of titanium carbide were produced through powder metallurgy. Produced composites were subjected to sliding wear test under dry condition through Taguchi’s L9 orthogonal design. Findings Optimal process condition to achieve the minimum wear rate was identified though the main effect plot. Sliding velocity was identified as the most dominating factor in the wear resistance. Practical implications The production of components with improved properties is promoted efficiently and economically by synthesizing the composite via powder metallurgy. Originality/value Though the investigations on the wear behavior of aluminium composites are analyzed, reinforcement types and the mode of fabrication have their significance in the metallurgical and mechanical properties. Thus, the produced component needs an in-detail study on the property evolution.

Wear behaviors of WC and TiC on co matrix composites under three-body impact abrasive wear condition

2019 ◽  
Vol 71 (7) ◽  
pp. 893-900 ◽  
Author(s):  
Lei Dong ◽  
Xiaoyu Zhang ◽  
Kun Liu ◽  
Xiaojun Liu ◽  
Ruiming Shi ◽  
...  
Keyword(s):  
Wear Rate ◽  
Abrasive Wear ◽  
Impact Energy ◽  
Wear Behavior ◽  
High Impact ◽  
Impact Wear ◽  
High Impact Energy ◽  
Content Type ◽  
Three Body ◽  
The Impact

Purpose The purpose of this paper is to investigate the tribological properties of the WC/TiC-Co substrate under different loading conditions under three impact abrasive wear conditions. Design/methodology/approach The three body collisional wear behavior of Co alloy with WC and TiC at three impact energy was studied from 1 to 3 J. Meanwhile, the microstructure, hardness, phase transformation and wear behavior of these specimens were investigated by scanning electron microscopy, Rockwell hardness (HRV), EDS and impact wear tester. The resulting wear rate was quantified by electronic balance measurements under different pressures. Findings The specific wear rate increases with the increase of the nonlinearity of the impact energy and the increase in the content of WC or TiC. The effect of TiC on wear rate is greater than that of WC, but the hardness is smaller. The wear characteristics of the samples are mainly characterized by three kinds of behavior, such as cutting wear, abrasive wear and strain fatigue wear. The WC-Co with fewer TiC samples suffered heavier abrasive wear than the more TiC samples under both low and high impact energy and underwent fewer strain fatigue wears under high impact energy. Originality/value The experimental results show that the wear resistance of the Co alloy is improved effectively and the excellent impact wear performance is achieved. The results can be used in cutting tools such as coal mine cutting machines or other fields.

Sign in / Sign up

Export Citation Format

Share Document