Contamination profile on typical printed circuit board assemblies vs soldering process

2014 ◽  
Vol 26 (4) ◽  
pp. 194-202 ◽  
Author(s):  
Helene Conseil ◽  
Morten Stendahl Jellesen ◽  
Rajan Ambat
Keyword(s):  
Printed Circuit Board ◽  
Circuit Board ◽  
Content Type ◽  
Contamination Control ◽  
Conformal Coating ◽  
Printed Circuit ◽  
Soldering Process ◽  
Wave Soldering ◽  
Solder Flux ◽  
Set Up

Purpose – The purpose of this paper was to analyse typical printed circuit board assemblies (PCBAs) processed by reflow, wave or selective wave soldering for typical levels of process-related residues, resulting from a specific or combination of soldering processes. Typical solder flux residue distribution pattern, composition and concentration are profiled and reported. The effect of such contaminants on conformal coating was tested. Design/methodology/approach – Presence of localized flux residues was visualized using a commercial residue reliability assessment testing gel test and chemical structure was identified by Fourier transform infrared spectroscopy, while the concentration was measured using ion chromatography, and the electrical properties of the extracts were determined by measuring the leak current using a twin platinum electrode set-up. Localized extraction of residue was carried out using a commercial critical contamination control extraction system. Findings – Results clearly show that the amount and distribution of flux residues are a function of the soldering process, and the level can be reduced by an appropriate cleaning. Selective soldering process generates significantly higher levels of residues compared to the wave and reflow process. For conformal coated PCBAs, the contamination levels generated from the tested wave and selective soldering process are found to be enough to generate blisters under exposure to high humidity levels. Originality/value – Although it is generally known that different soldering processes can introduce contamination on the PCBA surface, compromising its cleanliness, no systematic work is reported investigating the relative levels of residue introduced by various soldering processes and its effect on corrosion reliability.

Influence of the soldering paste type on optical and thermal parameters of LED modules

2022 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Krzysztof Górecki ◽  
Przemysław Ptak ◽  
Barbara Dziurdzia
Keyword(s):  
Design Methodology ◽  
Printed Circuit Board ◽  
Electrical Energy ◽  
Thermal Parameters ◽  
Circuit Board ◽  
Metal Core ◽  
Content Type ◽  
Printed Circuit ◽  
Soldering Process ◽  
Practical Implications

Purpose This paper presents the results of the investigations of LED modules soldered with the use of different soldering pastes. Design/methodology/approach The tested power LED modules are soldered using different solder pastes and soldering processes. Thermal parameters of the performed modules are tested using indirect electrical methods. The results of measurements obtained for different modules are compared and discussed. Findings It was shown that the soldering process visibly influences the results of measurements of optical and thermal parameters of LED modules. For example, values of thermal resistance of these modules and the efficiency of conversion of electrical energy into light differ between each other even by 15%. Practical implications The obtained results of investigations can be usable for designers of the assembly process of power LED modules. Originality/value This paper shows the investigations results in the area of effective assembly of power LEDs to the metal core printed circuit board (MCPCB) using different soldering pastes (REL22, REL61, LMPA-Q6, OM-5100, OM-338-PT, M8, OM-340, CVP-390). It was shown that the best thermal and optical properties of these modules are obtained for the OM5100 paste by Alpha Assembly.

Model updating of a temperature field simulation of a printed circuit board assembly based on the Kriging model

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Yutian Yin ◽  
Hongda Zhou ◽  
Cai Chen ◽  
Yi Zheng ◽  
Hongqiao Shen ◽  
...  
Keyword(s):  
Response Surface ◽  
Printed Circuit Board ◽  
Circuit Board ◽  
Printed Circuit Board Assembly ◽  
Content Type ◽  
Printed Circuit ◽  
Soldering Process ◽  
New Strategy ◽  
Circuit Board Assembly ◽  
Actual Profile

Purpose The simulated temperature profile of the printed circuit board assembly (PCBA) during reflow soldering process deviates from the actual profile. To reduce this relative deviation, a new strategy based on the Kriging response surface and the Multi-Objective Genetic Algorithm (MOGA) optimizing method is proposed. Design/methodology/approach The simulated temperature profile of the PCBA during reflow soldering process deviates from the actual profile. To reduce this relative deviation, a new strategy based on the Kriging response surface and the MOGA optimizing method is proposed. Findings Several critical influencing parameters such as temperature and the convective heat transfer coefficient of the specific temperature zones are selected as the correction parameters. The hyper Latins sampling method is implemented to distribute the design points, and the Kriging response surface model of the soldering process is constructed. The updated model is achieved and validated by the test. The relative derivation is reduced from the initial value of 43.4%–11.8% in terms of the time above the liquidus line. Originality/value A new strategy based on the Kriging response surface and the MOGA optimizing method is proposed.

Evaluation of new technologies and materials for printed circuit boards with improved heat dissipation properties

Circuit World ◽  
2016 ◽  
Vol 42 (1) ◽  
pp. 32-36 ◽  
Author(s):  
Michal Baszynski ◽  
Edward Ramotowski ◽  
Dariusz Ostaszewski ◽  
Tomasz Klej ◽  
Mariusz Wojcik ◽  
...  
Keyword(s):  
Thermal Properties ◽  
Printed Circuit Boards ◽  
Heat Dissipation ◽  
Printed Circuit Board ◽  
New Technologies ◽  
Electronic Device ◽  
Circuit Board ◽  
New Materials ◽  
Content Type ◽  
Printed Circuit

Purpose – The purpose of this paper is to evaluate thermal properties of printed circuit board (PCB) made with use of new materials and technologies. Design/methodology/approach – Four PCBs with the same layout but made with use of different materials and technologies have been investigated using thermal camera to compare their thermal properties. Findings – The results show how important the thermal properties of PCBs are for providing effective heat dissipation, and how a simple alteration to the design can help to improve the thermal performance of electronic device. Proper layout, new materials and technologies of PCB manufacturing can significantly reduce the temperature of electronic components resulting in higher reliability of electronic and power electronic devices. Originality/value – This paper shows the advantages of new technologies and materials in PCB thermal management.

Robotic system design and development for automated dismantling of PCB waste

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Ioan Doroftei ◽  
Daniel Chirita ◽  
Ciprian Stamate ◽  
Stelian Cazan ◽  
Carlos Pascal ◽  
...  
Keyword(s):  
Design Methodology ◽  
Printed Circuit Board ◽  
Vision System ◽  
Electronic Waste ◽  
Robotic System ◽  
Circuit Board ◽  
Short Introduction ◽  
Content Type ◽  
Printed Circuit ◽  
System A

Purpose The mass electronics sector is one of the most critical sources of waste, in terms of volume and content with dangerous effects on the environment. The purpose of this study is to provide an automated and accurate dismantling system that can improve the outcome of recycling. Design/methodology/approach Following a short introduction, the paper details the implementation layout and highlights the advantages of using a custom architecture for the automated dismantling of printed circuit board waste. Findings Currently, the amount of electronic waste is impressive while manual dismantling is a very common and non-efficient approach. Designing an automatic procedure that can be replicated, is one of the tasks for efficient electronic waste recovery. This paper proposes an automated dismantling system for the advanced recovery of particular waste materials from computer and telecommunications equipment. The automated dismantling architecture is built using a robotic system, a custom device and an eye-to-hand configuration for a stereo vision system. Originality/value The proposed approach is innovative because of its custom device design. The custom device is built using a programmable screwdriver combined with an innovative rotary dismantling tool. The dismantling torque can be tuned empirically.

Analysis of surface insulation resistance related failures in electronics by circuit simulation

Circuit World ◽  
2017 ◽  
Vol 43 (2) ◽  
pp. 45-55 ◽  
Author(s):  
Vadimas Verdingovas ◽  
Salil Joshy ◽  
Morten Stendahl Jellesen ◽  
Rajan Ambat
Keyword(s):  
Printed Circuit Board ◽  
Electronic Device ◽  
Early Stage ◽  
Circuit Simulation ◽  
Circuit Board ◽  
Insulation Resistance ◽  
Electronic Circuits ◽  
Content Type ◽  
Printed Circuit ◽  
Surface Insulation Resistance

Purpose The purpose of this study is to show that the humidity levels for surface insulation resistance (SIR)-related failures are dependent on the type of activators used in no-clean flux systems and to demonstrate the possibility of simulating the effects of humidity and contamination on printed circuit board components and sensitive parts if typical SIR data connected to a particular climatic condition are available. This is shown on representative components and typical circuits. Design/methodology/approach A range of SIR values obtained on SIR patterns with 1,476 squares was used as input data for the circuit analysis. The SIR data were compared to the surface resistance values observable on a real device printed circuit board assembly. SIR issues at the component and circuit levels were analysed on the basis of parasitic circuit effects owing to the formation of a water layer as an electrical conduction medium. Findings This paper provides a summary of the effects of contamination with various weak organic acids representing the active components in no-clean solder flux residue, and demonstrates the effect of humidity and contamination on the possible malfunctions and errors in electronic circuits. The effect of contamination and humidity is expressed as drift from the nominal resistance values of the resistors, self-discharge of the capacitors and the errors in the circuits due to parasitic leakage currents (reduction of SIR). Practical/implications The methodology of the analysis of the circuits using a range of empirical leakage resistance values combined with the knowledge of the humidity and contamination profile of the electronics can be used for the robust design of a device, which is also important for electronic products relying on low current consumption for long battery lifetime. Originality/value Examples provide a basic link between the combined effect of humidity and contamination and the performance of electronic circuits. The methodology shown provides the possibility of addressing the climatic reliability of an electronic device at the early stage of device design by using typical SIR data representing the possible climate exposure.

Study on fine lines and undercut suppression of printed circuit board prepared by electrolytic etching

Circuit World ◽  
2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Denglin Fu ◽  
Yanan Wen ◽  
Jida Chen ◽  
Lansi Lu ◽  
Ting Yan ◽  
...  
Keyword(s):  
Corrosion Inhibitor ◽  
Corrosion Inhibitors ◽  
Printed Circuit Board ◽  
Copper Surface ◽  
Etching Process ◽  
Circuit Board ◽  
Content Type ◽  
Printed Circuit ◽  
Etching Method ◽  
Electrolytic Etching

Purpose The purpose of this paper is to study an electrolytic etching method to prepare fine lines on printed circuit board (PCB). And the influence of organics on the side corrosion protection of PCB fine lines during electrolytic etching is studied in detail. Design/methodology/approach In this paper, the etching factor of PCB fine lines produced by new method and the traditional method was analyzed by the metallographic microscope. In addition, field emission scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS) were used to study the inhibition of undercut of the four organometallic corrosion inhibitors with 2,5-dimercapto-1,3,4-thiadiazole, benzotriazole, l-phenylalanine and l-tryptophan in the electrolytic etching process. Findings The SEM results show that corrosion inhibitors can greatly inhibit undercut of PCB fine lines during electrolytic etching process. XPS results indicate that N and S atoms on corrosion inhibitors can form covalent bonds with copper during electrolytic etching process, which can be adsorbed on sidewall of PCB fine lines to form a dense protective film, thereby inhibiting undercut of PCB fine lines. Quantum chemical calculations show that four corrosion inhibitor molecules tend to be parallel to copper surface and adsorb on copper surface in an optimal form. COMSOL Multiphysics simulation revealed that there is a significant difference in the amount of corrosion inhibitor adsorbed on sidewall of the fine line and the etching area. Originality/value As a clean production technology, electrolytic etching method has a good development indicator for the production of high-quality fine lines in PCB industry in the future. And it is of great significance in saving resources and reducing environmental pollution.

scholarly journals Advances in pressure sensing for vapour phase soldering process monitoring

2019 ◽  
Vol 31 (3) ◽  
pp. 169-175 ◽  
Author(s):  
Mohamed Amine Alaya ◽  
Attila Geczy ◽  
Balazs Illes ◽  
Gábor Harsányi ◽  
David Bušek
Keyword(s):  
Process Control ◽  
Printed Circuit Board ◽  
Pressure Sensors ◽  
Vapour Phase ◽  
Circuit Board ◽  
Power Functions ◽  
Monitoring Method ◽  
Content Type ◽  
Precise Control ◽  
Soldering Process

Purpose The purpose of the paper is to improve the control of vapour phase soldering (VPS). To enable better productivity and assembling quality, the industry needs to provide precise control and measurements during assembling. In the paper, a special monitoring method is presented for VPS to enable improved process control and oven state identification. Design/methodology/approach The work presents the investigation of the workspace with dynamic and gage type pressure sensors in fusion with thermocouples. Different sensors were evaluated to find an appropriate type. The relation between the temperature and the pressure was investigated, according to the setup of the oven. The effect of inserting a printed circuit board (PCB) on the pressure of the vapour inside the oven was also investigated with the pressure/power functions. Findings It was found that the novel gage-type sensors enable better precision than solutions seen in previous literature. The sensors are able to monitor the decreasing vapour concentration when a PCB is inserted to the workspace. It was found that there is a suggested minimum power to sustain a well-developed vapour column for soldering in saturated vapour. An inflexion point highlights this in the pressure/power function, in accordance with the temperature/power curve. Originality/value The research presents original works with aspects of a novel sensor fusion concept and work space monitoring for better process control and improved soldering quality.

Thermal decomposition of solder flux activators under simulated wave soldering conditions

2017 ◽  
Vol 29 (3) ◽  
pp. 133-143 ◽  
Author(s):  
Kamila Piotrowska ◽  
Morten Stendahl Jellesen ◽  
Rajan Ambat
Keyword(s):  
Thermal Treatment ◽  
Heat Exposure ◽  
Copper Surface ◽  
Substrate Material ◽  
Content Type ◽  
Soldering Process ◽  
Wave Soldering ◽  
Solder Flux ◽  
Solder Mask ◽  
The Impact

Purpose The aim of this work is to investigate the decomposition behaviour of the activator species commonly used in the wave solder no-clean flux systems and to estimate the residue amount left after subjecting the samples to simulated wave soldering conditions. Design/methodology/approach Changes in the chemical structure of the activators were studied using Fourier transform infrared spectroscopy technique and were correlated to the exposure temperatures within the range of wave soldering process. The amount of residue left on the surface was estimated using standardized acid-base titration method as a function of temperature, time of exposure and the substrate material used. Findings The study shows that there is a possibility of anhydride-like species formation during the thermal treatment of fluxes containing weak organic acids (WOAs) as activators (succinic and DL-malic). The decomposition patterns of solder flux activators depend on their chemical nature, time of heat exposure and substrate materials. Evaporation of the residue from the surface of different materials (laminate with solder mask, copper surface or glass surface) was found to be more pronounced for succinic-based solutions at highest test temperatures than for adipic acid. Less left residue was found on the laminate surface with solder mask (∼5-20 per cent of initial amount at 350°C) and poorest acid evaporation was noted for glass substrates (∼15-90 per cent). Practical implications The findings are attributed to the chemistry of WOAs typically used as solder flux activators. The results show the importance WOA type in relation to its melting/boiling points and the impact on the residual amount of contamination left after soldering process. Originality/value The results show that the evaporation of the flux residues takes place only at significantly high temperatures and longer exposure times are needed compared to the temperature range used for the wave soldering process. The extended time of thermal treatment and careful choice of fluxing technology would ensure obtaining more climatically reliable product.

Surface temperature of electronic assemblies equipped with tilted and low-powered QFN64 subjected to free convection

2017 ◽  
Vol 27 (6) ◽  
pp. 1304-1310 ◽  
Author(s):  
Abderrahmane Baïri ◽  
Clara Ortega Hermoso ◽  
David San Martén Ortega ◽  
Iken Baïri ◽  
Zsolt Peter
Keyword(s):  
Surface Temperature ◽  
Inclination Angle ◽  
Printed Circuit Board ◽  
Electronic Device ◽  
Thermal Design ◽  
Circuit Board ◽  
Content Type ◽  
Printed Circuit ◽  
Volume Method ◽  
Electronic Assemblies

Purpose This work deals with the case of the quad flat non-lead 64 (QFN64) electronic package generating a low power range ranging from 0.01 to 0.1W. It is installed on one side of a printed circuit board (PCB) that can be inclined relative to the horizontal plane with an angle varying between 0° and 90° (horizontal and vertical positions, respectively). The surface temperature of the electronic assembly is subjected to air natural convection. Design/methodology/approach Calculations are done by means of the finite volume method for many configurations obtained by varying the generated power and the inclination angle. Findings The distribution of the surface temperature is determined on all the assembly areas (QFN and PCB). The study shows that the thermal behaviour of the electronic device is influenced by the generated power and the inclination angle. The 3D numerical survey leads to correlations allowing calculation of the average surface temperature in any part of the assembly, according to the power generated by the QFN64 and the inclination angle. Originality/value The proposed accurate correlations are original and unpublished. They optimize the thermal design of the electronic QFN64 package, which is increasingly used in many engineering fields.

Sign in / Sign up

Export Citation Format

Share Document