Numerical Simulation of Coal and Natural Gas Co-Combustion in a Rotary Kiln with Different Excess Air Coefficient

Author(s):  
Junlin Xie ◽  
Ling Qin ◽  
Shuxia Mei ◽  
Zhengwen Zhang
Fuel ◽  
2021 ◽  
Vol 302 ◽  
pp. 121179
Author(s):  
Mingming Huang ◽  
Ruichuan Li ◽  
Jikang Xu ◽  
Shen Cheng ◽  
Haoxin Deng ◽  
...  

2014 ◽  
Vol 1006-1007 ◽  
pp. 181-184
Author(s):  
Zhu Sen Yang ◽  
Xing Hua Liu ◽  
Shu Chen

The combustion process of municipal solid waste (MSW) in a operating 750t/d grate furnace in Guangzhou was researched by means of numerical simulation. The influence of MSW moisture content on burning effect was discussed. The results show that: with the moisture content dropped from 50% to 30%, the heat value could be evaluated from 13.72% to 54.91% and the average temperature in the furnace could be promoted 90-248°C. However, the combustible gases and particle in the flue gas of outlet would take up a high proportion since lacking of oxygen would lead to an incomplete combustion. The excess air coefficient should be increased to 2.043~2.593 in order to ensure the flue gas residence time more than 2s and temperature in the furnace higher to 800°C.


2020 ◽  
Vol 181 (2) ◽  
pp. 31-39
Author(s):  
Ireneusz PIELECHA

Turbulent Jet Ignition systems are mainly dedicated to the combustion of lean mixtures of natural gas in heavy duty engines. The use of such a system in combination with lean mixtures leads to an increase in its overall efficiency. The article presents simulation analyzes of the impact of the excess air coefficient occurring in prechamber on the combustion process: combustion indicators and emission indicators. Tests on a single-cylinder engine with a displacement of about 4 dm3 at medium mixture (IMEP = 1.0 MPa) were carried out using the AVL Fire software. It was found that the incineration of global lean mixtures (lambda = 2) is effective when initiating this process (in the prechamber) with a charge of a stoichiometric composition. A strong relationship was found between the thermodynamic indicators in both prechamber and main chamber and the excess air coefficient initiating combustion.


Author(s):  
A. P. Shaikin ◽  
I. R. Galiev

The article analyzes the influence of chemical composition of hythane (a mixture of natural gas with hydrogen) on pressure in an engine combustion chamber. A review of the literature has showed the relevance of using hythane in transport energy industry, and also revealed a number of scientific papers devoted to studying the effect of hythane on environmental and traction-dynamic characteristics of the engine. We have studied a single-cylinder spark-ignited internal combustion engine. In the experiments, the varying factors are: engine speed (600 and 900 min-1), excess air ratio and hydrogen concentration in natural gas which are 29, 47 and 58% (volume).The article shows that at idling engine speed maximum pressure in combustion chamber depends on excess air ratio and proportion hydrogen in the air-fuel mixture – the poorer air-fuel mixture and greater addition of hydrogen is, the more intense pressure increases. The positive effect of hydrogen on pressure is explained by the fact that addition of hydrogen contributes to increase in heat of combustion fuel and rate propagation of the flame. As a result, during combustion, more heat is released, and the fuel itself burns in a smaller volume. Thus, the addition of hydrogen can ensure stable combustion of a lean air-fuel mixture without loss of engine power. Moreover, the article shows that, despite the change in engine speed, addition of hydrogen, excess air ratio, type of fuel (natural gas and gasoline), there is a power-law dependence of the maximum pressure in engine cylinder on combustion chamber volume. Processing and analysis of the results of the foreign and domestic researchers have showed that patterns we discovered are applicable to engines of different designs, operating at different speeds and using different hydrocarbon fuels. The results research presented allow us to reduce the time and material costs when creating new power plants using hythane and meeting modern requirements for power, economy and toxicity.


2020 ◽  
Vol 04 ◽  
Author(s):  
Guohai Jia ◽  
Lijun Li ◽  
Li Dai ◽  
Zicheng Gao ◽  
Jiping Li

Background: A biomass pellet rotary burner was chosen as the research object in order to study the influence of excess air coefficient on the combustion efficiency. The finite element simulation model of biomass rotary burner was established. Methods: The computational fluid dynamics software was applied to simulate the combustion characteristics of biomass rotary burner in steady condition and the effects of excess air ratio on pressure field, velocity field and temperature field was analyzed. Results: The results show that the flow velocity inside the burner gradually increases with the increase of inlet velocity and the maximum combustion temperature is also appeared in the middle part of the combustion chamber. Conclusion: When the excess air coefficient is 1.0 with the secondary air outlet velocity of 4.16 m/s, the maximum temperature of the rotary combustion chamber is 2730K with the secondary air outlet velocity of 6.66 m/s. When the excess air ratio is 1.6, the maximum temperature of the rotary combustion chamber is 2410K. When the air ratio is 2.4, the maximum temperature of the rotary combustion chamber is 2340K with the secondary air outlet velocity of 9.99 m/s. The best excess air coefficient is 1.0. The experimental value of combustion temperature of biomass rotary burner is in good agreement with the simulation results.


Sign in / Sign up

Export Citation Format

Share Document