Novel graphene heat spreaders for the thermal management of micro-LED arrays for optical communication

Author(s):  
N. Kudsieh ◽  
M. Khizar ◽  
M. Yasin Akhtar Raja
Author(s):  
Yasushi Koito ◽  
Yusaku Nonaka ◽  
Toshio Tomimura

A heat spreader is one of the solutions for thermal management of electronic and photonic systems. By placing the heat spreader between a small heat source and a large heat sink, the heat flux is spread from the former to the latter, resulting in a lower thermal spreading resistance between them. There are many types of heat spreaders known today having different heat transfer modes, shapes and sizes. This paper describes the theoretical study to present the fundamental data for the rational use and thermal design of heat spreaders. Two-dimensional disk-shaped mathematical model of the heat spreader is constructed, and the dimensionless numerical analysis is performed to investigate the thermal spreading characteristics of the heat spreaders. From the numerical results, the temperature distribution and the heat flow inside the heat spreaders are visualized, and then the effects of design parameters are clarified. The discussion is also made on the discharge characteristics of the heat spreaders. Moreover, a simple equation is proposed to evaluate the heat spreaders.


2008 ◽  
Vol 93 (11) ◽  
pp. 111907 ◽  
Author(s):  
R. H. Horng ◽  
C. C. Chiang ◽  
H. Y. Hsiao ◽  
X. Zheng ◽  
D. S. Wuu ◽  
...  

2013 ◽  
Vol 60 (2) ◽  
pp. 782-786 ◽  
Author(s):  
N. Lobo Ploch ◽  
H. Rodriguez ◽  
C. Stolmacker ◽  
M. Hoppe ◽  
M. Lapeyrade ◽  
...  

2019 ◽  
Vol 126 (16) ◽  
pp. 165113
Author(s):  
R. Soleimanzadeh ◽  
R. A. Khadar ◽  
M. Naamoun ◽  
R. van Erp ◽  
E. Matioli

Author(s):  
Ying Feng Pang ◽  
Elaine P. Scott ◽  
Zhenxian Liang ◽  
J. D. van Wyk

The objective of this work is to quantify the advantages of using double-sided cooling as the thermal management approach for the integrated power electronics modules. To study the potential advantage of the Embedded Power packaging method for the double-sided cooling, experiments were conducted. Three different cases were studied. To eliminate the effect of the heat sink on either side of the module, no heat sink was used in all three cases. The thermal tests were conducted such that the integrated power electronics modules were placed in the middle of flowing air in an insulated wind tunnel. Modules without additional top DBC, with additional top DBC, and with additional top DBC as well as heat spreaders on both sides were tested under the same condition. A common parameter, junction-to-ambient thermal resistance, was used to compare the thermal performance of these three cases. Despite the shortcoming of this parameter in describing the three-dimensional heat flow within the integrated power electronics modules, the concept of the thermal resistance is still worthwhile for evaluating various cooling methods for the module. The results show that increasing the top surface area can help in transferring the heat from the heat source to the ambient through the top side of the module. Consequently, the ability to handle higher power loss can also be increased. In summary, the Embedded Power technology provides an opportunity for implementing double-sided cooling as thermal management approach compared to modules with wire-bonded interconnects for the multichips.


Nanomaterials ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 3045
Author(s):  
Tae Kyoung Kim ◽  
Abu Bashar Mohammad Hamidul Islam ◽  
Yu-Jung Cha ◽  
Joon Seop Kwak

This work proposes the use of integrated high-power InGaN/GaN multiple-quantum-well flip-chip blue micro light-emitting diode (μ-LED) arrays on an AlGaN/GaN-based heterojunction field-effect transistor (HFET), also known as a high electron mobility transistor (HEMT), for various applications: underwater wireless optical communication (UWOC) and smart lighting. Therefore, we demonstrate high-power μ-LED-on-HEMT arrays that consist of 32 × 32 pixelated μ-LED arrays and 32 × 32 pixelated HEMT arrays and that are interconnected by a solder bump bonding technique. Each pixel of the μ-LED arrays emits light in the HEMT on-state. The threshold voltage, the off-state leakage current, and the drain current of the HEMT arrays are −4.6 V, <~1.1 × 10−9 A at gate-to-source voltage (VGS) = −10 V, and 21 mA at VGS = 4 V, respectively. At 12 mA, the forward voltage and the light output power (LOP) of μ-LED arrays are ~4.05 V and ~3.5 mW, respectively. The LOP of the integrated μ-LED-on-HEMT arrays increases from 0 to ~4 mW as the VGS increases from −6 to 4 V at VDD = 10 V. Each pixel of the integrated μ-LEDs exhibits a modulated high LOP at a peak wavelength of ~450 nm, showing their potential as candidates for use in UWOC.


2011 ◽  
Vol 1344 ◽  
Author(s):  
Zhong Yan ◽  
Guanxiong Liu ◽  
Javed Khan ◽  
Jie Yu ◽  
Samia Subrina ◽  
...  

ABSTRACTGraphene is a promising candidate material for thermal management of high-power electronics owing to its high intrinsic thermal conductivity. Here we report preliminary results of the proof-of-concept demonstration of graphene lateral heat spreaders. Graphene flakes were transferred on top of GaN devices through the mechanical exfoliation method. The temperature rise in the GaN device channels was monitored in-situ using micro-Raman spectroscopy. The local temperature was measured from the shift in the Raman peak positions. By comparing Raman spectra of GaN devices with and without graphene heat spreader, we demonstrated that graphene lateral heat spreaders effectively reduced the local temperature by ~ 20oC for a given dissipated power density. Numerical simulation of heat dissipation in the considered device structures gave results consistent with the experimental data.


Sign in / Sign up

Export Citation Format

Share Document