An Imaging Simulation Method of SAR for Three-dimensional Targets

2006 ◽  
Author(s):  
Zhang Peng ◽  
Yang Fang ◽  
Guo Chen Jiang ◽  
Xu Jia Dong
Keyword(s):  
Three Dimensional ◽  
Simulation Method ◽  
Imaging Simulation

scholarly journals Strata behavior and control strategy of backfilling collaborate with caving fully-mechanized mining

2020 ◽  
Vol 12 (1) ◽  
pp. 703-717
Author(s):  
Yin Wei ◽  
Wang Jiaqi ◽  
Bai Xiaomin ◽  
Sun Wenjie ◽  
Zhou Zheyuan
Keyword(s):  
Numerical Simulation ◽  
Control Strategy ◽  
Three Dimensional ◽  
Simulation Method ◽  
Mine Pressure ◽  
Hydraulic Support ◽  
Transition Area ◽  
Pressure Concentration ◽  
Strata Behavior ◽  
And Control

AbstractThis article analyzes the technical difficulties in full-section backfill mining and briefly introduces the technical principle and advantages of backfilling combined with caving fully mechanized mining (BCCFM). To reveal the strata behavior law of the BCCFM workface, this work establishes a three-dimensional numerical model and designs a simulation method by dynamically updating the modulus parameter of the filling body. By the analysis of numerical simulation, the following conclusions about strata behavior of the BCCFM workface were drawn. (1) The strata behavior of the BCCFM workface shows significant nonsymmetrical characteristics, and the pressure in the caving section is higher than that in the backfilling section. φ has the greatest influence on the backfilling section and the least influence on the caving section. C has a significant influence on the range of abutment pressure in the backfilling section. (2) There exits the transition area with strong mine pressure of the BCCFM workface. φ and C have significant effect on the degree of pressure concentration but little effect on the influence range of strong mine pressure in the transition area. (3) Under different conditions, the influence range of strong mine pressure is all less than 6 m. This article puts forward a control strategy of mine pressure in the transition area, which is appropriately improving the strength of the transition hydraulic support within the influence range (6 m) in the transition area according to the pressure concentration coefficient. The field measurement value of Ji15-31010 workface was consistent with numerical simulation, which verifies the reliability of control strategy of the BCCFM workface.

scholarly journals Study of the Effect of Centrifugal Force on Rotor Blade Icing Process

2017 ◽  
Vol 2017 ◽  
pp. 1-9 ◽  
Author(s):  
Zhengzhi Wang ◽  
Chunling Zhu
Keyword(s):  
Numerical Simulation ◽  
Centrifugal Force ◽  
Rotor Blade ◽  
Flow Direction ◽  
Three Dimensional ◽  
Simulation Method ◽  
Two Phase ◽  
Numerical Simulation Method ◽  
Calculation Results ◽  
Flow Field Characteristics

In view of the rotor icing problems, the influence of centrifugal force on rotor blade icing is investigated. A numerical simulation method of three-dimensional rotor blade icing is presented. Body-fitted grids around the rotor blade are generated using overlapping grid technology and rotor flow field characteristics are obtained by solving N-S equations. According to Eulerian two-phase flow, the droplet trajectories are calculated and droplet impingement characteristics are obtained. The mass and energy conservation equations of ice accretion model are established and a new calculation method of runback water mass based on shear stress and centrifugal force is proposed to simulate water flow and ice shape. The calculation results are compared with available experimental results in order to verify the correctness of the numerical simulation method. The influence of centrifugal force on rotor icing is calculated. The results show that the flow direction and distribution of liquid water on rotor surfaces change under the action of centrifugal force, which lead to the increasing of icing at the stagnation point and the decreasing of icing on both frozen limitations.

Thermo-mechanical coupling particle simulation of three-dimensional large-scale non-isothermal problems

2017 ◽  
Vol 34 (5) ◽  
pp. 1551-1571 ◽  
Author(s):  
Ming Xia
Keyword(s):  
Large Scale ◽  
Three Dimensional ◽  
Simulation Method ◽  
Particle Simulation ◽  
Similarity Criteria ◽  
Particle Model ◽  
Length Scale ◽  
Content Type ◽  
Mechanical Coupling ◽  
Particle Simulation Method

Purpose The main purpose of this paper is to present a comprehensive upscale theory of the thermo-mechanical coupling particle simulation for three-dimensional (3D) large-scale non-isothermal problems, so that a small 3D length-scale particle model can exactly reproduce the same mechanical and thermal results with that of a large 3D length-scale one. Design/methodology/approach The objective is achieved by following the scaling methodology proposed by Feng and Owen (2014). Findings After four basic physical quantities and their similarity-ratios are chosen, the derived quantities and its similarity-ratios can be derived from its dimensions. As the proposed comprehensive 3D upscale theory contains five similarity criteria, it reveals the intrinsic relationship between the particle-simulation solution obtained from a small 3D length-scale (e.g. a laboratory length-scale) model and that obtained from a large 3D length-scale (e.g. a geological length-scale) one. The scale invariance of the 3D interaction law in the thermo-mechanical coupled particle model is examined. The proposed 3D upscale theory is tested through two typical examples. Finally, a practical application example of 3D transient heat flow in a solid with constant heat flux is given to illustrate the performance of the proposed 3D upscale theory in the thermo-mechanical coupling particle simulation of 3D large-scale non-isothermal problems. Both the benchmark tests and application example are provided to demonstrate the correctness and usefulness of the proposed 3D upscale theory for simulating 3D non-isothermal problems using the particle simulation method. Originality/value The paper provides some important theoretical guidance to modeling 3D large-scale non-isothermal problems at both the engineering length-scale (i.e. the meter-scale) and the geological length-scale (i.e. the kilometer-scale) using the particle simulation method directly.

Calculation and Design Method Study of the Coil-Wound Heat Exchanger

2014 ◽  
Vol 1008-1009 ◽  
pp. 850-860 ◽  
Author(s):  
Zhou Wei Zhang ◽  
Jia Xing Xue ◽  
Ya Hong Wang
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Heat Exchanger ◽  
Design Method ◽  
Fluid Velocity ◽  
Exchange Process ◽  
Three Dimensional ◽  
Simulation Method ◽  
Physical Parameters ◽  
Numerical Result

A calculation method for counter-current type coil-wound heat exchanger is presented for heat exchange process. The numerical simulation method is applied to determine the basic physical parameters of wound bundles. By controlling the inlet fluid velocity varying in coil-wound heat exchanger to program and calculate the iterative process. The calculation data is analyzed by comparison of numerical result and the unit three dimensional pipe bundle model was built. Studies show that the introduction of numerical simulation can simplify the pipe winding process and accelerate the calculation and design of overall configuration in coil-wound heat exchanger. This method can be applied to the physical modeling and heat transfer calculation of pipe bundles in coil wound heat exchanger, program to calculate the complex heat transfer changing with velocity and other parameters, and optimize the overall design and calculation of spiral bundles.

Efficient Simulation of Gear Contacts Including Transient Elastohydrodynamic Effects

2013 ◽  
Vol 135 (3) ◽  
Author(s):  
Peter Fietkau ◽  
Bernd Bertsche
Keyword(s):  
Three Dimensional ◽  
Direct Determination ◽  
Simulation Method ◽  
Elastic Half Space ◽  
Operating Conditions ◽  
Multibody Simulation ◽  
Multibody Model ◽  
Gear Contact ◽  
Oil Films ◽  
Lubrication Conditions

This paper describes an efficient transient elastohydrodynamic simulation method for gear contacts. The model uses oil films and elastic deformations directly in the multibody simulation, and is based on the Reynolds equation including squeeze and wedge terms as well as an elastic half-space. Two transient solutions to this problem, an analytical and a numerical one, were developed. The analytical solution is accomplished using assumptions for the gap shape and the pressure in the middle of the gap. The numerical problem is solved using multilevel multi-integration algorithms. With this approach, tooth impacts during gear rattling as well as highly loaded power-transmitting gear contacts can be investigated and lubrication conditions like gap heights or type of friction may be determined. The method was implemented in the multibody simulation environment SIMPACK. Therefore it is easy to transfer the developed element to other models and use it for a multitude of different engineering problems. A detailed three-dimensional elastic multibody model of an experimental transmission is used to validate the developed method. Important values of the gear contact like normal and tangential forces, proportion of dry friction, and minimum gap heights are calculated and studied for different conditions. In addition, pressure distributions on tooth flanks as well as gap forms are determined based on the numerical solution method. Finally, the simulation approach is validated with measurements and shows good consistency. The simulation model is therefore capable of predicting transient gear contact under different operating conditions such as load vibrations or gear rattling. Simulations of complete transmissions are possible and therefore a direct determination of transmission vibration behavior and structure-borne noise as well as of forces and lubrication conditions can be done.

Study on the critical loosening condition toward a new design guideline for bolted joints

2018 ◽  
Vol 233 (9) ◽  
pp. 3302-3316 ◽  
Author(s):  
Hao Gong ◽  
Jianhua Liu ◽  
Xiaoyu Ding
Keyword(s):  
Three Dimensional ◽  
Element Model ◽  
Simulation Method ◽  
Bolted Joints ◽  
Design Guideline ◽  
Factors Affecting ◽  
Dimensional Finite Element ◽  
Frictional Coefficients ◽  
Three Dimensional Finite Element ◽  
Fit Tolerance

An understanding of conditions that trigger the loosening of bolted joints is essential to ensure joint reliability. In this study, a three-dimensional finite element model of a typical bolted joint is developed, and a new simulation method is proposed to quantitatively identify the critical transverse force for initiating loosening. This force is used to evaluate the anti-loosening capacity of bolted joints. Using the proposed simulation method, the effects of factors affecting critical loosening are systematically studied. It is found that the preload, frictional coefficients at the thread and the bearing surfaces, clamped length, and fit tolerance mainly affected loosening. When the preload and friction coefficients are increased, and the clamped length and fit tolerance are reduced, loosening is inhibited. Experiments are performed to demonstrate the reliability of the results. Finally, a suggestion is proposed to improve the design guideline VDI 2230 for bolted joints, which considers the requirement of avoiding loosening under vibrational loading.

An Optical Imaging Simulation Method for Inverted Microscope and its Application in Automatic Cell Manipulation

2012 ◽  
Vol 490-495 ◽  
pp. 1981-1985
Author(s):  
Qi Liang Du ◽  
Xue Song Lan ◽  
Ling Yuan ◽  
Rui Liang
Keyword(s):  
Optical Imaging ◽  
Forward Direction ◽  
Simulation Method ◽  
Considerable Effect ◽  
Cell Manipulation ◽  
Egg Cell ◽  
Virtual Image ◽  
Sensing Element ◽  
Inverted Microscope ◽  
Imaging Simulation

For a further understanding of the features of objects in the microscopic image during automatic cell manipulation, an optical imaging simulation method for inverted microscope was studied, with an assumption of parallel rays of light. The proposed method calculated the forward direction of every ray starting from the source until it reached the lens or disappeared from the effective range. A virtual image could be generated by an imitation of a CCD sensing element. Emulations in cases of a micro glass bar, a micro pipette and an egg cell which were commonly encountered in cell manipulation were carried out, whose gray-level virtual images were contrasted to real ones for verification. Results showed a considerable effect of the proposed simulation method

Motion Analysis and Simulation of Complex Curved Surface WEDM System

2008 ◽  
Vol 392-394 ◽  
pp. 151-155
Author(s):  
Tong Wang ◽  
K. Jiang ◽  
Shu Qiang Xie ◽  
Shuang Shuang Hao
Keyword(s):  
Electrical Discharge Machining ◽  
Three Dimensional ◽  
Simulation Method ◽  
Curved Surface ◽  
Polar Coordinates ◽  
Curved Surfaces ◽  
Machining Quality ◽  
Motion Parameters ◽  
Dimensional Graph ◽  
Analysis Of Motion

In this paper, the characteristics and general laws of cutting complex curved surface by wire electrical discharge machining (WEDM) system are studied. Based on analysis of motion parameters the universal mathematical model of polar coordinates is derived. Moreover, the simulation of WEDM system is introduced, which is carried out by using language Visual C++ and the three dimensional graph software OpenGL.This simulation method is helpful in improving machining quality and productivity of complex curved surfaces, and is fundation for establishing CAD/CAPP/CAM technology in WEDM.

The Research on Steering Fracture Numerical Simulation

2013 ◽  
Vol 734-737 ◽  
pp. 1488-1492
Author(s):  
Zhen Yu Liu ◽  
Li Hong Yao ◽  
Hu Zhen Wang ◽  
Cui Cui Ye
Keyword(s):  
Numerical Simulation ◽  
Finite Element Method ◽  
Finite Element ◽  
Three Dimensional ◽  
Simulation Method ◽  
Production Performance ◽  
Phase Flow ◽  
Water Production ◽  
Two Phase ◽  
Fractured Well

The fractures after artificial steering fracturing appear in shades of curved surface. Aiming at the problem of steering fracture, in the paper, numerical simulation method under the condition of three-dimensional two-phase flow is presented based on finite element method. In this method, of steering fracture was achieved by adopting surface elements fractures and tetrahedron elements to describe formation. By numerical simulation, the change rule of oil and water production performance of steering fractures can be calculated, and then the steering fracture parameters can be optimized before fracturing. A new method was supplied for the numerical simulation of artificial fractured well.

Numerical and theoretical analyses of the dynamics of droplets driven by electrowetting on dielectric in a Hele-Shaw cell

2018 ◽  
Vol 839 ◽  
pp. 468-488 ◽  
Author(s):  
Yasufumi Yamamoto ◽  
Takahiro Ito ◽  
Tatsuro Wakimoto ◽  
Kenji Katoh
Keyword(s):  
Theoretical Model ◽  
Contact Line ◽  
Three Dimensional ◽  
Simulation Method ◽  
Movement Speed ◽  
Electrowetting On Dielectric ◽  
Moving Contact Line ◽  
Moving Contact ◽  
Droplet Movement ◽  
Hele Shaw Cell

Droplet movement by electrowetting on dielectric (EWOD) in a Hele-Shaw cell is analysed theoretically and numerically. We propose a simple theoretical model for the motion, which describes well the voltage dependency of droplet speed below the saturation voltage as measured experimentally. The simulation method for numerical analyses is constructed by using the Young–Lippmann equation to represent EWOD and the generalised Navier boundary condition to represent the moving contact line in the context of the front-tracking method. With an adjusted slip parameter, the present full three-dimensional numerical simulation reproduces well the shape evolution and movement speed of droplets as observed experimentally. We verify the proposed theoretical model in numerical experiments with various shapes and voltages. Furthermore, we analyse theoretically the behaviour of the contact line at the onset of droplet motion as observed in the simulation and experiment, and we are able to estimate very well the time scale on which the contact angle changes.

Sign in / Sign up

Export Citation Format

Share Document