scholarly journals Strata behavior and control strategy of backfilling collaborate with caving fully-mechanized mining

2020 ◽  
Vol 12 (1) ◽  
pp. 703-717
Author(s):  
Yin Wei ◽  
Wang Jiaqi ◽  
Bai Xiaomin ◽  
Sun Wenjie ◽  
Zhou Zheyuan
Keyword(s):  
Numerical Simulation ◽  
Control Strategy ◽  
Three Dimensional ◽  
Simulation Method ◽  
Mine Pressure ◽  
Hydraulic Support ◽  
Transition Area ◽  
Pressure Concentration ◽  
Strata Behavior ◽  
And Control

AbstractThis article analyzes the technical difficulties in full-section backfill mining and briefly introduces the technical principle and advantages of backfilling combined with caving fully mechanized mining (BCCFM). To reveal the strata behavior law of the BCCFM workface, this work establishes a three-dimensional numerical model and designs a simulation method by dynamically updating the modulus parameter of the filling body. By the analysis of numerical simulation, the following conclusions about strata behavior of the BCCFM workface were drawn. (1) The strata behavior of the BCCFM workface shows significant nonsymmetrical characteristics, and the pressure in the caving section is higher than that in the backfilling section. φ has the greatest influence on the backfilling section and the least influence on the caving section. C has a significant influence on the range of abutment pressure in the backfilling section. (2) There exits the transition area with strong mine pressure of the BCCFM workface. φ and C have significant effect on the degree of pressure concentration but little effect on the influence range of strong mine pressure in the transition area. (3) Under different conditions, the influence range of strong mine pressure is all less than 6 m. This article puts forward a control strategy of mine pressure in the transition area, which is appropriately improving the strength of the transition hydraulic support within the influence range (6 m) in the transition area according to the pressure concentration coefficient. The field measurement value of Ji15-31010 workface was consistent with numerical simulation, which verifies the reliability of control strategy of the BCCFM workface.

scholarly journals Study of the Effect of Centrifugal Force on Rotor Blade Icing Process

2017 ◽  
Vol 2017 ◽  
pp. 1-9 ◽  
Author(s):  
Zhengzhi Wang ◽  
Chunling Zhu
Keyword(s):  
Numerical Simulation ◽  
Centrifugal Force ◽  
Rotor Blade ◽  
Flow Direction ◽  
Three Dimensional ◽  
Simulation Method ◽  
Two Phase ◽  
Numerical Simulation Method ◽  
Calculation Results ◽  
Flow Field Characteristics

In view of the rotor icing problems, the influence of centrifugal force on rotor blade icing is investigated. A numerical simulation method of three-dimensional rotor blade icing is presented. Body-fitted grids around the rotor blade are generated using overlapping grid technology and rotor flow field characteristics are obtained by solving N-S equations. According to Eulerian two-phase flow, the droplet trajectories are calculated and droplet impingement characteristics are obtained. The mass and energy conservation equations of ice accretion model are established and a new calculation method of runback water mass based on shear stress and centrifugal force is proposed to simulate water flow and ice shape. The calculation results are compared with available experimental results in order to verify the correctness of the numerical simulation method. The influence of centrifugal force on rotor icing is calculated. The results show that the flow direction and distribution of liquid water on rotor surfaces change under the action of centrifugal force, which lead to the increasing of icing at the stagnation point and the decreasing of icing on both frozen limitations.

Calculation and Design Method Study of the Coil-Wound Heat Exchanger

2014 ◽  
Vol 1008-1009 ◽  
pp. 850-860 ◽  
Author(s):  
Zhou Wei Zhang ◽  
Jia Xing Xue ◽  
Ya Hong Wang
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Heat Exchanger ◽  
Design Method ◽  
Fluid Velocity ◽  
Exchange Process ◽  
Three Dimensional ◽  
Simulation Method ◽  
Physical Parameters ◽  
Numerical Result

A calculation method for counter-current type coil-wound heat exchanger is presented for heat exchange process. The numerical simulation method is applied to determine the basic physical parameters of wound bundles. By controlling the inlet fluid velocity varying in coil-wound heat exchanger to program and calculate the iterative process. The calculation data is analyzed by comparison of numerical result and the unit three dimensional pipe bundle model was built. Studies show that the introduction of numerical simulation can simplify the pipe winding process and accelerate the calculation and design of overall configuration in coil-wound heat exchanger. This method can be applied to the physical modeling and heat transfer calculation of pipe bundles in coil wound heat exchanger, program to calculate the complex heat transfer changing with velocity and other parameters, and optimize the overall design and calculation of spiral bundles.

The Research on Steering Fracture Numerical Simulation

2013 ◽  
Vol 734-737 ◽  
pp. 1488-1492
Author(s):  
Zhen Yu Liu ◽  
Li Hong Yao ◽  
Hu Zhen Wang ◽  
Cui Cui Ye
Keyword(s):  
Numerical Simulation ◽  
Finite Element Method ◽  
Finite Element ◽  
Three Dimensional ◽  
Simulation Method ◽  
Production Performance ◽  
Phase Flow ◽  
Water Production ◽  
Two Phase ◽  
Fractured Well

The fractures after artificial steering fracturing appear in shades of curved surface. Aiming at the problem of steering fracture, in the paper, numerical simulation method under the condition of three-dimensional two-phase flow is presented based on finite element method. In this method, of steering fracture was achieved by adopting surface elements fractures and tetrahedron elements to describe formation. By numerical simulation, the change rule of oil and water production performance of steering fractures can be calculated, and then the steering fracture parameters can be optimized before fracturing. A new method was supplied for the numerical simulation of artificial fractured well.

Study on the Operation Characteristics of Electrostatic Fabric Precipitator

2012 ◽  
Vol 616-618 ◽  
pp. 2013-2016
Author(s):  
Chao Fan Sun ◽  
Xing Lu Yu ◽  
Xin Feng Long ◽  
Bo Lou ◽  
De Bo Li
Keyword(s):  
Numerical Simulation ◽  
High Performance ◽  
Simulation Method ◽  
Fabric Filter ◽  
Fluid Field ◽  
Airflow Distribution ◽  
Internal Fluid ◽  
Result Show ◽  
Removal Technology ◽  
And Control

Numerical simulation method was used in this paper and 3-D structure of model was established with Pro/Engineering. It is evident that the efficiency of electric-bag is related to internal fluid field. The internal fluid field characteristics (pressure field, velocity field, turbulence field and particle tracks) are obtained by the numerical simulation soft called Fluent, the result show that airflow distribution could be improved obviously by the flow deflectors in electrostatic precipitation area. And the distribution of DPM in filter area is non uniform, which would lead to various damage on bags and affect the operation of electrostatic fabric filter. All these work have important significance for the study of new dust removal technology, developments of high performance precipitator, reduction of dust pollution and control of air pollution as well.

scholarly journals Study on Fluorine Pollution in a Slag Yard

2019 ◽  
Vol 9 (5) ◽  
pp. 847
Author(s):  
Lide Wei ◽  
Changfu Wei ◽  
Sugang Sui
Keyword(s):  
Numerical Simulation ◽  
Experimental Investigation ◽  
Numerical Simulations ◽  
Solute Transport ◽  
Large Scale ◽  
Three Dimensional ◽  
Simulation Method ◽  
Laboratory Studies ◽  
Survey Results ◽  
Simulation Results

This paper suggests a large-scale three-dimensional numerical simulation method to investigate the fluorine pollution near a slag yard. The large-scale three-dimensional numerical simulation method included an experimental investigation, laboratory studies of solute transport during absorption of water by soil, and large-scale three-dimensional numerical simulations of solute transport. The experimental results showed that the concentrations of fluorine from smelting slag and construction waste soil were well over the discharge limit of 0.1 kg/m3 recommended by Chinese guidelines. The key parameters of the materials used for large-scale three-dimensional numerical simulations were determined based on an experimental investigation, laboratory studies, and soil saturation of survey results and back analyses. A large-scale three-dimensional numerical simulation of solute transport was performed, and its results were compared to the experiment results. The simulation results showed that the clay near the slag had a high saturation of approximately 0.9, consistent with the survey results. Comparison of the results showed that the results of the numerical simulation of solute transport and the test results were nearly identical, and that the numerical simulation results could be used as the basis for groundwater environmental evaluation.

Transient Simulation of a Three-Dimensional Moving Downburst

2012 ◽  
Vol 446-449 ◽  
pp. 3875-3878
Author(s):  
Bai Feng Ji ◽  
Wei Lian Qu
Keyword(s):  
Fluid Dynamics ◽  
Numerical Simulation ◽  
Computational Fluid Dynamics ◽  
Wind Field ◽  
Three Dimensional ◽  
Simulation Method ◽  
Transient Simulation ◽  
Dynamics Simulation ◽  
Transmission Tower ◽  
Transient Wind

Thunderstorm microbursts, which are sources of extreme wind loadings in nature, have caused numerous structural failures, especially collapses of transmission tower around the world. Numerical simulation using computational fluid dynamics (CFD) has recently made significant progress in simulating downbursts. In this paper, transient simulation of a three-dimensional moving downburst was studied using computational fluid dynamics simulation method. Transient simulation of a three-dimensional moving downburst was conducted using time-filtered Reynolds Averaged Navier-Stokes (RANS) numerical simulation method. The three-dimensional transient wind field characteristics in a moving downburst were studied in detail. The results indicate that transient wind field characteristics in a moving downburst present quite different characteristics compared with stationary downburst at different heights and radial positions.

Three-Dimensional Numerical Simulation of the Flow around Two Side-by-Side Cylinders of Different Diameters

2014 ◽  
Vol 721 ◽  
pp. 199-202
Author(s):  
Zhen Xiao Bi ◽  
Zhi Han Zhu
Keyword(s):  
Numerical Simulation ◽  
Flow Direction ◽  
Three Dimensional ◽  
Cross Flow ◽  
Simulation Method ◽  
Scale Model ◽  
Hydrodynamic Characteristics ◽  
Eddy Simulation ◽  
Drag And Lift ◽  
Different Diameters

This paper presents the calculation of hydrodynamic characteristics of two side-by-side cylinders of different diameters in three dimensional incompressible uniform cross flow by using Large-eddy simulation method based on dynamical Smagorinsky-Lilly sub-grid scale model. Solution of the three dimensional N-S equations were obtained by the finite volume method. The numerical simulation focused on investigating the characteristic of the pressure distribution (drag and lift force), vorticity field and turbulence Re=. Results shows that, the asymmetry of the time –averaged velocity distribution in the flow direction behind the two cylinders is very obvious; the frequency of eddy shedding of the small cylinder is about twice of the large one. The turbulence of cylinders is more obvious.

Experiment and Numerical Simulation of Extrudate Swell in the Polymer Extrusion Process

2011 ◽  
Vol 314-316 ◽  
pp. 401-404 ◽  
Author(s):  
Min Zhang ◽  
Chuan Zhen Huang ◽  
Guo Wen Chen ◽  
Yu Xi Jia
Keyword(s):  
Numerical Simulation ◽  
High Speed ◽  
Three Dimensional ◽  
Simulation Method ◽  
Extrusion Process ◽  
High Speed Photography ◽  
The Finite Element Method ◽  
Polymer Extrusion ◽  
Extrudate Swell ◽  
Rate Profile

The extrudate swell of the polymer extrusion process was studied with the experiment and simulation method. The extrudate swell process was recorded by the high-speed photography apparatus. The swell rate at the different time was calculated. It is found that the extrudate swell rate increase at the first five seconds. The maximum swell rate is about 4.37%. The three-dimensional numerical simulation model of the experiment die path was founded. The extrusion process including the extrudate swell was simulated used the Finite Element Method. Such simulated results as the velocity vector, the shear rate profile and the end of the swell zone were analyzed. The extrudate swell end got by the simulation is similar with the experiment result.

scholarly journals Research on Model Slice and Forming Method of Thin-walled Parts

2021 ◽  
Vol 233 ◽  
pp. 04046
Author(s):  
Changhao Zhang ◽  
Hu Li ◽  
Jianyu Yang ◽  
Huawei Lu ◽  
Peng Su
Keyword(s):  
Numerical Simulation ◽  
Temperature Field ◽  
Structural Characteristics ◽  
Three Dimensional ◽  
Simulation Method ◽  
Processing Parameters ◽  
Transient Temperature ◽  
Transient Temperature Field ◽  
Thin Walled ◽  
Experimental Processing

According to the structural characteristics of thin-walled parts, a model slicing method is proposed, and its mathematical process is established. The three-dimensional transient temperature field in the process of synchronous powder feeding laser cladding is studied and verified by numerical simulation method, and the thin-walled parts formed by later experimental processing are processed by the results of numerical simulation. Using the simulation results of temperature field as the basis for optimizing the processing parameters, the forming path of thin-walled parts is programmed and optimized, and the experimental verification shows the reliability of this method.

scholarly journals Three-Dimensional Numerical Simulation of Multiscale Fractures and Multiphase Flow in Heterogeneous Unconventional Reservoirs with Coupled Fractal Characteristics

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-15
Author(s):  
Hong Li ◽  
Haiyang Yu ◽  
Nai Cao ◽  
Shiqing Cheng ◽  
He Tian ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Multiphase Flow ◽  
Water Saturation ◽  
Three Dimensional ◽  
Horizontal Wells ◽  
Simulation Method ◽  
Fractal Model ◽  
Point Pattern ◽  
Permeability Model ◽  
Heterogeneous Model

A simulated reservoir model, based on the permeability fractal model and three-dimensional (3D) Gaussian filter, was established to account for in-layer and interlayer heterogeneity so that the result conforms to the law of geological statistics. Combined with an embedded discrete fracture method (EDFM), a multiscale fracture system was established, forming the numerical simulation method of multiphase flow in horizontal wells in heterogeneous reservoirs with complex fractures. The heterogeneity and saturation of the reservoir mixed five-point pattern of vertical and horizontal wells and the injection and production of horizontal wells were discussed. The results show that it is difficult to characterize complex reservoirs using a homogeneous permeability model. Thus, it is best to use a heterogeneous model that considers permeability differences in tight reservoirs. Formation fluids coexist in multiple phases, and water saturation has a direct effect on the production. Thus, a multiphase flow model is needed and can play a greater role in injection and production technology. The mixed five-point pattern of vertical and horizontal wells can improve productivity to a certain extent, but the dual effects of heterogeneity and fracturing will cause a decline in production by accelerating the communication of injected fluid. The reservoir is heterogeneous between wells, and there are differing effects on adjacent wells. Therefore, near-well natural microfractures are opened because of fracturing in horizontal wells, and the heterogeneity cannot be ignored, especially when multiple wells are simultaneously injected and produced.

Sign in / Sign up

Export Citation Format

Share Document