scholarly journals SOME PROPERTIES OF PHOSPHORIC ACID STABILISED LATERIZED ADOBE BRICKS

2020 ◽  
Vol 32 (3) ◽  
Author(s):  
Adekemi Loretta Ayodele ◽  
Abdulhalim Oshioke Mohammed ◽  
Adeyemi Babayemi Fajobi ◽  
Akindehinde Ayotunde Akindahunsi ◽  
Aderopo Musiliu Olajumoke
Keyword(s):  
Compressive Strength ◽  
Statistical Analysis ◽  
Moisture Content ◽  
Phosphoric Acid ◽  
Analysis Of Variance ◽  
Ambient Air ◽  
Dry Density ◽  
Minimum Requirement ◽  
Curing Period ◽  
Dry Soil

The changes in the compressive strength of laterized bricks produced from stabilised residual tropical laterite (RTL) are reported in this paper. The RTL was stabilised with different percentages (2, 4, 6 and 8%) by weight of dry soil of 1M phosphoric acid (PA). Some geotechnical properties and elemental oxide composition of the RTL were determined. Adobe bricks were produced from the PA stabilised, 5% cement stabilised and unstabilised RTL. Adobe bricks produced from 5% cement stabilised RTL served as the control. The bricks were cured under ambient air condition for 7, 14, 21 and 28 days. The pH, dry density, moisture content and compressive strength (fc) of the bricks were determined at the end of each curing period. The influence of PA was evaluated using the changes in the fc of the adobe bricks. The effectiveness of PA was also evaluated using a standard minimum requirement. Statistical analysis of the results was done using Analysis of variance. There was about 90 and 200% increase in fc of PA and cement stabilised Adobe bricks, respectively. The fc of 6% PA stabilised and cement stabilised adobe bricks met the minimum requirement. It is concluded that PA has great potential for stabilising Adobe bricks for building.

A Study of Soil Stabilization by Hydrated Lime at Kampung Kedaik Asal, Rompin, Pahang, Malaysia

2014 ◽  
Vol 695 ◽  
pp. 738-741
Author(s):  
Azhani Zukri ◽  
Nadiatul Adilah Ahmad Abdul Ghani
Keyword(s):  
Compressive Strength ◽  
Moisture Content ◽  
Unconfined Compressive Strength ◽  
Soil Stabilization ◽  
Optimum Moisture Content ◽  
Natural State ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Lime Content ◽  
Curing Period

This study involves the clay sample which is taken from Kampung Kedaik Asal, Rompin site and evaluation of its properties in natural state and after stabilization. The main objectives of this paper is to estimate the optimum lime content (OLC) needed to stabilize the soil by using Eades-Grim pH Test, to determine the optimum moisture content (OMC) and maximum dry density (MDD) of the treated soil by Standard Proctor Test and also the strength value of the soil specimens with different percentages of lime content corresponding with different curing period by Unconfined Compressive Strength (UCS) Test. From this study, the optimum amount to stabilize the clay soil and minimum amount of lime required to stabilize the soil pH level to 12 is 5%. The results showed that addition of lime decreased the maximum dry density (MDD) and increased the optimum moisture content (OMC). Unconfined compressive test on 48 sets of samples has been carried out for 7, 14 and 28 days of curing with different lime contents such as 5%, 7% and 9%. The highest unconfined compressive strength (UCS) achieved is 321 kN/m2 for clay stabilized with 9% lime content cured at 28 days. From the test results, it was found that the longer the immersion of curing period with higher lime content, the greater the compressive strength of the specimen.

scholarly journals Influence of Nanolime and Curing Period on Unconfined Compressive Strength of Soil

2017 ◽  
Vol 2017 ◽  
pp. 1-9 ◽  
Author(s):  
Panbarasi Govindasamy ◽  
Mohd Raihan Taha ◽  
Jamal Alsharef ◽  
Kowstubaa Ramalingam
Keyword(s):  
Compressive Strength ◽  
Moisture Content ◽  
Unconfined Compressive Strength ◽  
Curing Time ◽  
Strength Gain ◽  
Treated Soil ◽  
Soil Particles ◽  
Curing Period

This paper presents the improvement of the unconfined compressive strength (UCS) of soil by mixing different percentages of nanolime and 5% lime with soil. The UCS of treated soil increased significantly over curing time with increasing percentage of nanolime. The optimum results were reached at only 0.5% nanolime admixtures which were much higher than 5% lime admixture. This may be due to higher ability of nanolime to flocculate and agglomerate the soil particles compared with the lime. In addition, the lime could fill only the micropores while nanolime could fill the micro- and nanopores as well. The strength gain is inversely proportional to the remolded moisture content and curing period. However, when the content of nanolime used is larger than 0.5%, nanolime particles are not uniformly dispersed. Therefore, a weak area in the form of voids is created, consequently the homogeneous hydrated microstructure cannot be formed, and finally the strength will decrease.

MECHANICAL PROPERTIES OF FLY ASH-BASED ALKALI-ACTIVATED CEMENT USING A STATISTICAL ANALYSIS TECHNIQUE

2014 ◽  
Vol 1 (1) ◽  
Author(s):  
Hyuk Lee ◽  
Vanissorn Vimonsatit
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Statistical Analysis ◽  
Fly Ash ◽  
Silica Fume ◽  
Dry Density ◽  
Analysis Method ◽  
Solid Ratio ◽  
Alkali Activated ◽  
Alkali Activated Cement

This paper presents the mechanical properties of fly ash-based alkali-activated cement (AAC). A statistical analysis method was used to determine the effect of mix proportion parameters on the dry density and compressive strength of fly ash-based AAC pastes and mortars. For that purpose, sample mixtures were designed according to Taguchi’s experimental design method, i.e., in a L9 orthogonal array. Four factors were selected: “silica fume content” (SF), “sand to solid ratio” (s/c), “liquid to solid ratio” (l/s), and “superplasticiser content” (SP). The experimental results were analysed by using signal to noise for quality control of each mixture, and analysis of variance (ANOVA) was used to determine the significant effect on the compressive strength of fly ash-based AAC. Furthermore, a regression-analysis method was used to predict the compressive strength according to the variation of the four factors. Results indicated that silica fume is the most influencing parameter on compressive strength, which could be decreased by superplasticiser and l/s ratio. There is no significant effect of sand-to-cementitious ratio on compressive strength of fly ash-based AAC. The dry density decreases as the sand-to-cementitious ratio is decreased. The increasing l/s ratio and superplasticiser dosage could further decrease the dry density of fly ash-based AAC.

scholarly journals Strength Improvement of Weak Subgrade Soil Using Cement and Lime

2019 ◽  
Vol 4 (1) ◽  
Author(s):  
Anigilaje B Salahudeen ◽  
Ja’afar A Sadeeq
Keyword(s):  
Compressive Strength ◽  
Moisture Content ◽  
Unconfined Compressive Strength ◽  
Optimum Moisture Content ◽  
Atterberg Limits ◽  
California Bearing Ratio ◽  
Natural Soil ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Subgrade Soil

The study investigate the suitability of subgrade soil in Baure Local Government Area of Kastina State Nigeria for road construction. The strength properties of the  subgrade was improved using lime and cement. Several analysis including the particle size distribution, specific gravity, Atterberg limits, compaction characteristics, unconfined compressive strength and California bearing ratio tests were performed on natural and lime/cement treated soil samples in accordance with BS 1377 (1990) and BS 1924 (1990) respectively. Soil specimens were prepared by mixing the soil with lime and cement in steps of 0, 3, 6, and 9% by weight of dry soil in several percentage combinations. The Atterberg limits of the weak subgrade soils improved having a minimum plasticity index value of 5.70 % at 3%Lime/6%Cement contents. The maximum dry density (MDD) values obtained showed a significant improvement having a peak value of 1.66 kN/m3 at 9%Lime/9%Cement contents. Similarly, a minimum value of 18.50 % was observed for optimum moisture content at 9%Lime/9%Cement contents which is a desirable reduction from a value of 25.00 % for the natural soil. The unconfined compressive test value increased from 167.30 kN/m2 for the natural soil to 446.77 kN/m2 at 9%Lime/9%Cement contents 28 days curing period. Likewise, the soaked California bearing ratio values increased from 2.90 % for the natural soil to 83.90 % at 9%Lime/9%Cement contents. Generally, there were improvements in the engineering properties of the weak subgrade soil when treated with lime and cement. However, the peak UCS value of 446.77 kN/m2 fails to meet the recommended UCS value of 1710 KN/m2 specified by TRRL (1977) as a criterion for adequate stabilization using Ordinary Portland Cement.            Keywords: Weak subgrade soil, Lime, Cement, Atterberg limits, Maximum dry density, Optimum moisture content, Unconfined compressive strength, California bearing ratio

Laboratory Investigation on the Strength Characteristics of Cement-Treated Base

2014 ◽  
Vol 507 ◽  
pp. 353-360 ◽  
Author(s):  
Amiruddin Ismail ◽  
Mojtaba Shojaei Baghini ◽  
Mohamed Rehan Karim ◽  
Foad Shokri ◽  
Ramez A. Al-Mansob ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Moisture Content ◽  
Unconfined Compressive Strength ◽  
Resilient Modulus ◽  
Tension Test ◽  
Engineering Properties ◽  
Dry Density ◽  
Flexure Strength ◽  
Indirect Tension ◽  
Indirect Tension Test

Cement-Treated Base (CTB) is a non-conventional method used in road bases materials to improve its engineering properties due to the hardening of cement when moisture is present and extends the period of curing times. This study investigates the effects of cement additive on properties of base layer using laboratory mechanistic evaluation of stabilized soil mixtures. Laboratory tests conducted were Unconfined Compressive Strength (UCS), Indirect Tension test for Resilient Modulus (ITRM) and Flexure Strength (FS) tests. The results revealed that by adding Portland cement, the mechanical properties of the mixture have improved where the UCS is found to be an important quality indicator. In addition, the variables that influenced these tests, which are cement content, curing time, moisture content, and dry density, play important role to determine the performance of CTB. This paper presents the finding of a correlation conducted to analyse the influences of these variables using regression and ANOVA to establish significant models with the aim of predicting the strength base on mixture parameters. Keywords: Cement-Treated Base, Unconfined Compressive Strength, Indirect Tension test for Resilient Modulus, Flexure Strength, Moisture Content, Dry Density, Regression Analysis.

scholarly journals Layered Grouting Technology Based on a Comprehensive Water-to-Cement Ratio for the Overlying Loess Stratum of Urban Shallow Tunnels

2020 ◽  
Vol 2020 ◽  
pp. 1-13
Author(s):  
Teng Yang ◽  
Jiaqi Zhang ◽  
Xiao Zhang ◽  
Qingsong Zhang ◽  
Zhanchao Yin
Keyword(s):  
Compressive Strength ◽  
Moisture Content ◽  
Strain Curve ◽  
Test System ◽  
Engineering Properties ◽  
Dry Density ◽  
Road Tunnel ◽  
Cement Ratio ◽  
Grouting Pressure ◽  
Water To Cement Ratio

Different from sand and clay, loess has special engineering properties; hence, existing soil grouting theories are not suitable for the disaster treatment of shallow loess tunnels. In this study, a fine grouting reinforcement test system was developed, and the Yuhan Road tunnel overlying loess was used as the injection medium. An orthogonal test based on slurry dry density, moisture content, water-to-cement ratio, and grouting pressure was conducted. Results revealed that the loess samples have high integrity after grouting, and the cohesion and compressive strength improved significantly. The stress-strain curve showed that the strengthened samples have greater ultimate and residual strengths than samples before grouting. Through a range analysis, it was determined that water-to-cement ratio and moisture content are the main factors affecting loess cohesion and compressive strength. Therefore, a comprehensive test of the water-to-cement ratio and moisture content as a single variable was conducted. It was found that their influence on loess cohesion and compressive strength is not a single linear relationship but a combined balance. To characterize the joint effect of water in loess and in slurry on reinforcement, the concept of a comprehensive water-to-cement ratio is proposed, and the cohesion and compressive strength curves with respect to this ratio were drawn. An optimal comprehensive water-to-cement ratio, which corresponds to the maximum cohesion or compressive strength, was found. Based on this ratio, we further propose a method to calculate the water-to-cement ratio of slurry and suitable grouting amount for the Yuhan Road tunnel reinforcement project, in which all solution parameters can be measured via field tests. In the project, a surface layered grouting scheme, based on the optimal comprehensive water-to-cement ratio, was designed. After grouting, loess strength was improved significantly, permeability was reduced greatly, and the overall reinforcement effect was suitable; these results provide a reference for similar projects.

The Compressive Strength of Flemish Bond Wall by Exploiting Spent Copper Slag from Shipyard Waste

2014 ◽  
Vol 700 ◽  
pp. 407-412
Author(s):  
Salmaliza Salleh ◽  
Shaaban Md Ghazaly ◽  
Mahmud Hilmi ◽  
Suresh Rao
Keyword(s):  
Compressive Strength ◽  
Moisture Content ◽  
Copper Slag ◽  
Masonry Wall ◽  
Brick Wall ◽  
Leaching Tests ◽  
Compressive Test ◽  
Minimum Requirement ◽  
Physical Tests ◽  
Control Set

This research has been conducted to investigate the compressive strength of Flemish bond spent copper slag masonry wall. The spent copper slag was taken from a shipyard and repair company in Pasir Gudang, Johor, Malaysia. In total three (3) sets of brick wall were built based on different percentage of spent copper slag replacement in bricks. The first set was arranged with 0% spent copper slag replacement bricks. It is used as the control set. The rest 2 sets were prepared by replacing 20% and 30% of sand in the bricks with spent copper slag. These bricks and walls were undergone physical tests such as compressive test, moisture content, density and leaching tests to satisfy the minimum requirement of a standard brick.

scholarly journals Experimental Study on the Effect of Water on the Properties of Cast In Situ Foamed Concrete

2018 ◽  
Vol 2018 ◽  
pp. 1-11 ◽  
Author(s):  
Wenhui Zhao ◽  
Qian Su ◽  
Wubin Wang ◽  
Lele Niu ◽  
Ting Liu
Keyword(s):  
Compressive Strength ◽  
Elastic Modulus ◽  
Moisture Content ◽  
Water Level ◽  
Immersion Time ◽  
Drying Shrinkage ◽  
Dry Density ◽  
Volumetric Moisture Content ◽  
Foamed Concrete

This study aims to investigate the effect of water on the properties of cast in situ foamed concrete with a dry density of 300–800 kg/m3 (100 kg/m3 is a gradient). Firstly, the shrinkage deformation with the curing time and the volumetric moisture content is studied by the drying shrinkage test and improved drying shrinkage test. Secondly, the influence of volumetric moisture content on mechanical properties is assessed. At last, the effects of immersion time and immersion type on the mechanical properties of foamed concrete are studied by considering the water-level conditions. The achieved results show that the shrinkage deformations increase with the curing time for the drying shrinkage test and the improved drying shrinkage test, while the variations are different. The shrinkage deformation increases with the decrease of volumetric moisture content for six dry densities of foamed concrete. Besides, it gradually changes in the early stage, while it changes fast in the later stage. The compressive strength and elastic modulus decrease with the increase of volumetric moisture content for each density. For the water-level unchanged condition, the compressive strength and elastic modulus initially decrease and then slowly increase with the increase of the immersion time. For the water-level changed condition, the compressive strength and elastic modulus of foamed concrete decrease with the increase of immersion time for each dry density, and the rate of early attenuation is high, whereas the rate of later attenuation is limited.

scholarly journals Soil Stabilization using Polypropylene Clamshell Food Containers

2021 ◽  
Vol 1200 (1) ◽  
pp. 012031
Author(s):  
N A C M Salwi ◽  
N Hamzah
Keyword(s):  
Compressive Strength ◽  
Moisture Content ◽  
Physical Properties ◽  
Soil Stabilization ◽  
Clayey Soil ◽  
Plastic Waste ◽  
Engineering Properties ◽  
Dry Density ◽  
Successful Implementation ◽  
Food Container

Abstract Soil stabilization is the method of improving the physical properties of soil, such as shear strength and bearing capacity of the soil, by using controlled compaction or the addition of admixtures to produce an improved soil material that has all the desired engineering properties. The new technique of soil stabilization uses plastic waste as an alternative material is of outmost crucial since plastic wastes are non-biodegradable and remain intact after being buried in soil for many years. The present study is focused on investigating the effectiveness of utilizing polypropylene clamshell food containers as soil stabilizers. The physical properties of the untreated clayey soil are determined by conducting moisture content, specific gravity, particle size distribution, and the Atterberg limit test. Also, the Standard Proctor compaction test, as well as the unconfined compressive strength test, are carried out to determine the compaction and strength parameters of the soil sample before and after reinforcing with different percentages of polypropylene clamshell food container strips such as 0.4%, 0.8%, and 1.2%. Findings from this study indicate that the addition of polypropylene clamshell food container strips in the clayey soil is capable of becoming a soil stabilizer agent as the optimum compressive strength of the soil was achieved with replacement of 0.8% of plastic strips, along with increasing the Optimum Moisture Content (OMC) while decreasing the Maximum Dry Density (MDD). Successful implementation of polypropylene plastic in soil stabilization can help minimize the volume of plastic waste in the environment, which then leads to developing a sustainable future by utilizing recyclable material as alternative sources in the geotechnical field.

Correlation of UCS and CBR on Lightweight Geocomposite of Soil-EPS Stabilized by Waste of Buton Asphalt

2020 ◽  
Vol 998 ◽  
pp. 311-316
Author(s):  
Ichsan Rauf ◽  
Lawalenna Samang ◽  
Tri Harianto ◽  
Ardy Arsyad
Keyword(s):  
Compressive Strength ◽  
Mechanical Behavior ◽  
Compression Test ◽  
Expanded Polystyrene ◽  
California Bearing Ratio ◽  
Dry Density ◽  
Period Effect ◽  
Unconfined Compression ◽  
Unconfined Compression Test ◽  
Curing Period

The conventional embankment has disadvantages in terms of its weight; it has an implication for the level of deformation that will occur on the subgrade layer. This study was conducted dealing with the design of geocomposite material compositions based on their mechanic characteristics. The lightweight geocomposit material (LWGM) was constructed by composing soil with expanded polystyrene (EPS) with by-product of buton asphalt as the binder agent (WBA). Unconfined Compression Test (UCT) and California Bearing Ratio (CBR) were examined to figure out the mechanical behavior of LWGM. The percentages of WBA used on specimens were 3%, 5%, 7% and 9%, while those of EPS were 0.15% and 0.30%, based on weight of soils dry density. Furthermore, to understand the curing period effect, all the specimens were cured and tested within 7 days and 28 days. The results showed that the LWGM could reduce the embankment densities from 20% to 35%, compared to conventional embankment. The compressive strength and CBR values presented the same tendency, so that, based on correlation of UCS and CBR value, the LWGM compositions that are appropriate for road foundation criteria as subbase courses are 3.2% to 7% for the WBA and 0,15% - 0,30% for the EPS.

Sign in / Sign up

Export Citation Format

Share Document