A Vibrational Mode Analysis of Free Finite-Length Thick Cylinders Using the Finite Element Method

1998 ◽  
Vol 120 (2) ◽  
pp. 371-377 ◽  
Author(s):  
Huan Wang ◽  
Keith Williams ◽  
Wei Guan
Keyword(s):  
Finite Length ◽  
Natural Frequencies ◽  
Three Dimensional ◽  
Mode Analysis ◽  
Mode Shapes ◽  
Vibrational Modes ◽  
The Finite Element Method ◽  
Cylinder Length ◽  
Radial Thickness ◽  
Thick Cylinder

Based on their three-dimensional mode shapes, the vibrational modes of free finite length thick cylinders can be classified into 6 categories, consisting of pure radial, radial motion with radial shearing, extensional, circumferential, axial bending, and global modes. This classification, together with the numbers of both the circumferential and the longitudinal nodes, is sufficient to identify each mode of a finite length thick cylinder. The mode classification was verified experimentally by measurements on a thick cylinder. According to the displacement distribution ratio in the radial, tangential and longitudinal directions, the effect of varying cylinder length on the vibrational modes is such that all the modes can be broadly categorized as either pure radial modes, or non pure radial modes. The natural frequencies and mode shapes of the former are dependent upon only the radial dimensions of the models, while the natural frequencies and mode shapes of the latter are dependent upon both the axial length and radial thickness.

scholarly journals Modal analysis of an iced offshore composite wind turbine blade

2021 ◽  
pp. 0309524X2110116
Author(s):  
Oumnia Lagdani ◽  
Mostapha Tarfaoui ◽  
Mourad Nachtane ◽  
Mourad Trihi ◽  
Houda Laaouidi
Keyword(s):  
Wind Turbine ◽  
Modal Analysis ◽  
Turbine Blade ◽  
Natural Frequencies ◽  
Wind Turbine Blade ◽  
Resonance Phenomenon ◽  
Mode Shapes ◽  
The Finite Element Method ◽  
Numerical Work ◽  
Composite Blades

In the far north, low temperatures and atmospheric icing are a major danger for the safe operation of wind turbines. It can cause several problems in fatigue loads, the balance of the rotor and aerodynamics. With the aim of improving the rigidity of the wind turbine blade, composite materials are currently being used. A numerical work aims to evaluate the effect of ice on composite blades and to determine the most adequate material under icing conditions. Different ice thicknesses are considered in the lower part of the blade. In this paper, modal analysis is performed to obtain the natural frequencies and corresponding mode shapes of the structure. This analysis is elaborated using the finite element method (FEM) computer program through ABAQUS software. The results have laid that the natural frequencies of the blade varied according to the material and thickness of ice and that there is no resonance phenomenon.

Effect of Delamination on Natural Frequencies of E-glass and S-glass Epoxy Composite Plates

2021 ◽  
Author(s):  
P. K. Karsh ◽  
Bindi Thakkar ◽  
R. R. Kumar ◽  
Abhijeet Kumar ◽  
Sudip Dey
Keyword(s):  
Natural Frequencies ◽  
Epoxy Composite ◽  
Orientation Angle ◽  
Laminated Composite ◽  
Composite Plates ◽  
Mode Shapes ◽  
Transverse Shear Deformation ◽  
The Finite Element Method ◽  
Modes Of Failure ◽  
Ply Orientation

The delamination is one of the major modes of failure occurring in the laminated composite due to insufficient bonding between the layers. In this paper, the natural frequencies of delaminated S-glass and E-glass epoxy cantilever composite plates are presented by employing the finite element method (FEM) approach. The rotary inertia and transverse shear deformation are considered in the present study. The effect of parameters such as the location of delamination along the length, across the thickness, the percentage of delamination, and ply-orientation angle on first three natural frequencies of the cantilever plates are presented for S-glass and E-glass epoxy composites. The standard eigenvalue problem is solved to obtain the natural frequencies and corresponding mode shapes. First three mode shape of S-Glass and E-Glass epoxy laminated composites are portrayed corresponding to different ply angle of lamina.

Split Vibration Modes in Acoustically-Coupled Disk Stacks

1995 ◽  
Author(s):  
Jung-Ge Tseng ◽  
Jonathan Wickert
Keyword(s):  
Natural Frequencies ◽  
Three Dimensional ◽  
System Level ◽  
Thin Plates ◽  
Mode Shapes ◽  
Design Parameters ◽  
Phase System ◽  
Acoustic Coupling ◽  
Annular Plates ◽  
Vibration Model

Abstract Vibration of an array of stacked annular plates, in which adjacent plates couple weakly through an acoustic layer, is investigated through experimental and theoretical methods. Such acoustic coupling manifests itself through split natural frequencies, beating in the time responses of adjacent or separated plates, and system-level modes in which plates in the array vibrate in- or out-of-phase at closely-spaced frequencies. Laboratory measurements, including a technique in which the frequency response function of all in-phase modes but no out-of-phase modes, or visa versa, is measured, demonstrate the contribution of coupling to the natural frequency spectrum, and identify the combinations of design parameters for which it is important. For the lower modes of primary interest here, the natural frequencies of the out-of-phase system modes decrease as the air layer becomes thinner, while those of the in-phase mode remain sensibly constant at the in vacuo values. A vibration model comprising N classical thin plates that couple through the three-dimensional acoustic fields established in the annular cavities between plates is developed, and its results are compared with measurements of the natural frequencies and mode shapes.

In-Plane Vibration Modes of Arbitrarily Thick Disks

1997 ◽  
Author(s):  
Kevin I. Tzou ◽  
Jonathan A. Wickert ◽  
Adnan Akay
Keyword(s):  
Natural Frequencies ◽  
Arbitrary Dimension ◽  
Three Dimensional ◽  
Mode Shapes ◽  
Vibration Modes ◽  
Three Dimensional Model ◽  
Bending Vibration ◽  
Annular Disk ◽  
Out Of Plane ◽  
Plane Bending

Abstract The three-dimensional vibration of an arbitrarily thick annular disk is investigated for two classes of boundary conditions: all surfaces traction-free, and all free except for the clamped inner radius. These two models represent limiting cases of such common engineering components as automotive and aircraft disk brakes, for which existing models focus on out-of-plane bending vibration. For a disk of significant thickness, vibration modes in which motion occurs within the disk’s equilibrium plane can play a substantial role in setting its dynamic response. Laboratory experiments demonstrate that in-plane modes exist at frequencies comparable to those of out-of-plane bending even for thickness-to-diameter ratios as small as 10−1. The equations for three-dimensional motion are discretized through the Ritz technique, yielding natural frequencies and mode shapes for coupled axial, radial, and circumferential deformations. This treatment is applicable to “disks” of arbitrary dimension, and encompasses classical models for plates, bars, cylinders, rings, and shells. The solutions so obtained converge in the limiting cases to the values expected from the classical theories, and to ones that account for shear deformation and rotary inertia. The three-dimensional model demonstrates that for geometries within the technologically-important range, the natural frequencies of certain in- and out-of-plane modes can be close to one another, or even identically repeated.

Dynamic Modeling of a Ball-Screw Drive and Identification of Its Installation Parameters

2020 ◽  
Vol 143 (4) ◽  
Author(s):  
Yu-Jia Hu ◽  
Yaoyu Wang ◽  
Weidong Zhu ◽  
Haolin Li
Keyword(s):  
Dynamic Model ◽  
Natural Frequencies ◽  
Data Fitting ◽  
Ball Screw ◽  
Mode Shapes ◽  
The Finite Element Method ◽  
Screw Drive ◽  
Log Normal ◽  
Ball Screw Drive ◽  
Log Normal Distribution

Abstract Parametric expressions of equivalent stiffnesses of a ball-screw shaft are obtained by derivation of its geometric parameters, the finite element method (FEM), and data fitting based on a modified probability density function of log-normal distribution. A dynamic model of a ball-screw drive that considers effects of bearing stiffnesses, the mass of the nut, and the axial pretension is established based on equivalent stiffnesses of its shaft. With the dynamic model and modal experimental results obtained by Bayesian operational modal analysis (BOMA), installation parameters of the ball-screw drive are identified by a genetic algorithm (GA) with a new comprehensive objective function that considers natural frequencies, mode shapes, and flexibility of the ball-screw drive. The effectiveness of the methodology is experimentally validated.

scholarly journals A Study on the Effect of Carbon Nanotubes’ Distribution and Agglomeration in the Free Vibration of Nanocomposite Plates

2020 ◽  
Vol 6 (4) ◽  
pp. 79
Author(s):  
D. S. Craveiro ◽  
M. A. R. Loja
Keyword(s):  
Carbon Nanotubes ◽  
Elastic Properties ◽  
Natural Frequencies ◽  
Mechanical Performance ◽  
Negative Impact ◽  
Free Vibrations ◽  
Mode Shapes ◽  
The Finite Element Method ◽  
Agglomeration Effect ◽  
Performance Predictions

The present work aimed to characterize the free vibrations’ behaviour of nanocomposite plates obtained by incorporating graded distributions of carbon nanotubes (CNTs) in a polymeric matrix, considering the carbon nanotubes’ agglomeration effect. This effect is known to degrade material properties, therefore being important to predict the consequences it may bring to structures’ mechanical performance. To this purpose, the elastic properties’ estimation is performed according to the two-parameter agglomeration model based on the Eshelby–Mori–Tanaka approach for randomly dispersed nano-inclusions. This approach is implemented in association with the finite element method to determine the natural frequencies and corresponding mode shapes. Three main agglomeration cases were considered, namely, agglomeration absence, complete agglomeration, and partial agglomeration. The results show that the agglomeration effect has a negative impact on the natural frequencies of the plates, regardless the CNTs’ distribution considered. For the corresponding vibrations’ mode shapes, the agglomeration effect was shown in most cases not to have a significant impact, except for two of the cases studied: for a square plate and a rectangular plate with symmetrical and unsymmetrical CNTs’ distribution, respectively. Globally, the results confirm that not accounting for the nanotubes’ agglomeration effect may lead to less accurate elastic properties and less structures’ performance predictions.

An Exact Solution for the Natural Frequencies of Flexible Beams Undergoing Overall Motions

2003 ◽  
Vol 9 (11) ◽  
pp. 1221-1229 ◽  
Author(s):  
Ali H Nayfeh ◽  
S.A. Emam ◽  
Sergio Preidikman ◽  
D.T. Mook
Keyword(s):  
Exact Solution ◽  
Natural Frequencies ◽  
Three Dimensional ◽  
Beam Theory ◽  
Free Vibrations ◽  
Mode Shapes ◽  
Flexible Beam ◽  
Bernoulli Beam ◽  
Flexible Beams ◽  
Euler Bernoulli Beam

We investigate the free vibrations of a flexible beam undergoing an overall two-dimensional motion. The beam is modeled using the Euler-Bernoulli beam theory. An exact solution for the natural frequencies and corresponding mode shapes of the beam is obtained. The model can be extended to beams undergoing three-dimensional motions.

Frequency Clusters in the Spectrum of Annular Cylinders

1998 ◽  
Vol 65 (4) ◽  
pp. 797-803 ◽  
Author(s):  
K. I. Tzou ◽  
J. A. Wickert ◽  
A. Akay
Keyword(s):  
Natural Frequencies ◽  
Spectral Characteristics ◽  
Three Dimensional ◽  
Longitudinal Shear ◽  
Forced Response ◽  
Infinite Cylinder ◽  
Propagation Theory ◽  
Cylinder Length ◽  
Vibration Model ◽  
Shear Modes

As the length of a traction-free annular cylinder is increased, distinct members within any family of radial or longitudinal shear modes have natural frequencies that asymptotically approach a common nonzero value. Such modes, potentially having significantly different numbers of nodes along the cylinder’s generator, can have natural frequencies that are indistinguishable from one another within the resolution of test equipment or numerical simulation. The three-dimensional vibration model discussed here predicts the formation of narrow “frequency clusters” with the cylinder’s increasing length, the converged value of which bounds from below the frequencies of all modes within a particular family. In addition to these spectral characteristics, frequency clusters have implications for the forced response of annular cylinders. For the particular families of modes that are of interest here, the steady-state harmonic response at frequencies near a cluster can be spatially confined with displacements that decay rapidly away from the point of maximum response. At other driving frequencies, the response is distributed more uniformly along the length of the cylinder. The derived analytical model is compared with results from laboratory measurements, and from the predictions of wave propagation theory in the limit of infinite cylinder length.

Forced and Ambient Vibration Tests and Vibration Monitoring of Hakucho Suspension Bridge

2000 ◽  
Vol 1696 (1) ◽  
pp. 57-63 ◽  
Author(s):  
Yozo Fujino ◽  
Masato Abe ◽  
Hajime Shibuya ◽  
Masato Yanagihara ◽  
Masashi Sato ◽  
...  
Keyword(s):  
Natural Frequencies ◽  
Three Dimensional ◽  
Suspension Bridge ◽  
Element Model ◽  
Vibration Monitoring ◽  
Ambient Vibration ◽  
Mode Shapes ◽  
Ambient Vibration Tests ◽  
Bending Mode ◽  
Vibration Tests

Forced and ambient dynamic tests of the Hakucho Bridge were carried out to study the dynamic characteristics of this suspension bridge. Dense-array measurement was employed in order to capture not only natural frequencies and damping, but also the mode shapes of the bridge. The natural frequencies and mode shapes obtained from the forced and ambient vibration tests agreed well with those calculated by a three-dimensional finite element model. A new method that combines the random decrement method with the Ibrahim time domain method is proposed to systematically identify the natural frequencies, damping, and mode shapes. This method is successfully applied to ambient vibration data. It is shown that the natural frequency of the first vertical bending mode decreases noticeably as the wind speed increases. It is also shown that the shape of the first vertical bending mode changes slightly near the towers, depending on the wind velocity; this finding indicates that the change may be associated with friction in the bearings at the towers. Finally, application of the Global Positioning System to measure static displacement of the girder is explained.

Sign in / Sign up

Export Citation Format

Share Document