Effects of a High Porous Material on Heat Transfer and Flow in a Circular Tube

2008 ◽  
Vol 131 (2) ◽  
Author(s):  
Koichi Ichimiya ◽  
Tetsuaki Takeda ◽  
Takuya Uemura ◽  
Tetsuya Norikuni
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Porous Material ◽  
Entropy Generation ◽  
Circular Tube ◽  
Flow Characteristics ◽  
Reynolds Numbers ◽  
Working Fluid ◽  
Equivalent Diameter

This paper describes the heat transfer and flow characteristics of a heat exchanger tube filled with a high porous material. Fine copper wires (diameter: 0.5 mm) were inserted in a circular tube dominated by thermal conduction and forced convection. The porosity was from 0.98 to 1.0. The working fluid was air. The hydraulic equivalent diameter was cited as the characteristic length in the Nusselt number and the Reynolds number. The Nusselt number and the friction factor were expressed as functions of the Reynolds number and porosity. The thermal performance was evaluated by the ratio of the Nusselt number with and without a high porous material and the entropy generation. It was recognized that the high porous material was effective in low Reynolds numbers and the Reynolds number, which minimized the entropy generation existed.

Effects of a High Porous Material on Heat Transfer and Flow in a Circular Tube

2007 ◽  
Author(s):  
Koichi Ichimiya ◽  
Tetsuaki Takeda ◽  
Takuya Uemura ◽  
Tetsuya Norikuni
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Porous Material ◽  
Entropy Generation ◽  
Circular Tube ◽  
Copper Wire ◽  
Flow Characteristics ◽  
Working Fluid ◽  
Equivalent Diameter

This paper describes the heat transfer and flow characteristics of a heat exchanger tube filled with a high porous material. Fine copper wire (diamete: 0.5 mm) was inserted in a circular tube dominated by thermal conduction and forced convection. The porosity was from 0.98 to 1.0. Working fluid was air. Hydraulic equivalent diameter was cited as the characteristic length in Nusselt number and Reynolds number. Nusselt number and friction factor were expressed as functions of Reynolds number and porosity. Thermal performance was evaluated by the ratio of Nusselt number with and without a high porous material and the entropy generation. It was recognized that the high porous material was effective in low Reynolds number and the Reynolds number which minimized the entropy generation existed.

Investigation of Heat Transfer and Flow Characteristics in Heat Exchanger With Microscale Channels

2007 ◽  
Author(s):  
Shaokun Xu ◽  
Baoming Chen ◽  
Shui Ji ◽  
Shiqi Zhao
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Heat Exchanger ◽  
Prandtl Number ◽  
Ethylene Glycol ◽  
Flow Characteristics ◽  
Equivalent Diameter ◽  
Flow Friction ◽  
Glycol Solution

The experimental study of heat transfer and flow characteristics are conducted for water and ethylene-glycol solution flowing in the heat exchanger with rectangular or triangular microscale channels, which have equivalent diameter of 0.55mm, 0.91mm, 1.38mm and 5mm. During experiments, the Reynolds number ranges from 300 to 2500. The experimental results show that: at a fixed Reynolds number, the Nusselt number increases along with increasing equivalent diameter, the Nusselt number for ethylene-glycol solution with larger Prandtl number is greater than that for water, the geometrical configuration of the microscale channels have a significant effect on the heat transfer; the flow friction factors of microscale channels are smaller than that of normal channels, flow characteristics of rectangular channels are evidently better than that of triangular, the flow friction factor decreases with increasing Reynolds number, the experiment also show that the flow friction factor is independent of Prandtl number; The critical Reynolds number at which the flow transiting to turbulent flow is 700∼1200.

Convective Heat Transfer Investigation of a Confined Air Slot-Jet Impingement Cooling on Corrugated Surfaces With Different Wave Shapes

2018 ◽  
Vol 141 (2) ◽  
Author(s):  
Recep Ekiciler ◽  
Muhammet Samet Ali Çetinkaya ◽  
Kamil Arslan
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Flow Characteristics ◽  
Jet Impingement ◽  
Working Fluid ◽  
Bottom Surface ◽  
Air Jet ◽  
Corrugated Surfaces ◽  
Energy Equations

In this study, air jet impingement on flat, triangular-corrugated, and sinusoidal-corrugated surfaces was numerically investigated. Bottom surface was subjected to constant surface temperature. Air was the working fluid. The air exited from a rectangular shaped slot and impinged on the bottom surface. The Reynolds number was changed between 125 and 500. The continuity, momentum, and energy equations were solved using the finite volume method. The effect of the shape of bottom surface on heat and flow characteristics was investigated in detail. Average and local Nusselt number were calculated for each case. It was found out that Nusselt number increases by increasing the Reynolds number. The optimum conditions were established to get much more enhancement in terms of performance evaluation criterion (PEC). It was revealed that the shape of the cooling surface (bottom wall) influences the heat transfer substantially.

Heat transfer enhancement using second mode self-oscillating structures

2019 ◽  
Vol 30 (7) ◽  
pp. 3827-3842
Author(s):  
Samer Ali ◽  
Zein Alabidin Shami ◽  
Ali Badran ◽  
Charbel Habchi
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Laminar Flow ◽  
Flow Regime ◽  
Vortex Generator ◽  
Reynolds Numbers ◽  
Content Type ◽  
Laminar Flow Regime ◽  
Second Mode

Purpose In this paper, self-sustained second mode oscillations of flexible vortex generator (FVG) are produced to enhance the heat transfer in two-dimensional laminar flow regime. The purpose of this study is to determine the critical Reynolds number at which FVG becomes more efficient than rigid vortex generators (RVGs). Design/methodology/approach Ten cases were studied with different Reynolds numbers varying from 200 to 2,000. The Nusselt number and friction coefficients of the FVG cases are compared to those of RVG and empty channel at the same Reynolds numbers. Findings For Reynolds numbers higher than 800, the FVG oscillates in the second mode causing a significant increase in the velocity gradients generating unsteady coherent flow structures. The highest performance was obtained at the maximum Reynolds number for which the global Nusselt number is improved by 35.3 and 41.4 per cent with respect to empty channel and rigid configuration, respectively. Moreover, the thermal enhancement factor corresponding to FVG is 72 per cent higher than that of RVG. Practical implications The results obtained here can help in the design of novel multifunctional heat exchangers/reactors by using flexible tabs and inserts instead of rigid ones. Originality/value The originality of this paper is the use of second mode oscillations of FVG to enhance heat transfer in laminar flow regime.

Investigating Gas Turbine Internal Cooling Using Supercritical CO2 at High Reynolds Numbers for Direct Fired Cycle Applications

2021 ◽  
Author(s):  
Matthew Searle ◽  
Arnab Roy ◽  
James Black ◽  
Doug Straub ◽  
Sridharan Ramesh
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Gas Turbines ◽  
Cfd Simulation ◽  
Reynolds Numbers ◽  
Navier Stokes ◽  
Process Conditions ◽  
Internal Cooling ◽  
Air Breathing

Abstract In this paper, experimental and numerical investigations of three variants of internal cooling configurations — dimples only, ribs only and ribs with dimples have been explored at process conditions (96°C and 207bar) with sCO2 as the coolant. The designs were chosen based on a review of advanced internal cooling features typically used for air-breathing gas turbines. The experimental study described in this paper utilizes additively manufactured square channels with the cooling features over a range of Reynolds number from 80,000 to 250,000. Nusselt number is calculated in the experiments utilizing the Wilson Plot method and three heat transfer characteristics — augmentation in Nusselt number, friction factor and overall Thermal Performance Factor (TPF) are reported. To explore the effect of surface roughness introduced due to additive manufacturing, two baseline channel flow cases are considered — a conventional smooth tube and an additively manufactured square tube. A companion computational fluid dynamics (CFD) simulation is also performed for the corresponding cooling configurations reported in the experiments using the Reynolds Averaged Navier Stokes (RANS) based turbulence model. Both experimental and computational results show increasing Nusselt number augmentation as higher Reynolds numbers are approached, whereas prior work on internal cooling of air-breathing gas turbines predict a decay in the heat transfer enhancement as Reynolds number increases. Comparing cooling features, it is observed that the “ribs only” and “ribs with dimples” configurations exhibit higher Nusselt number augmentation at all Reynolds numbers compared to the “dimples only” and the “no features” configurations. However, the frictional losses are almost an order of magnitude higher in presence of ribs.

Impingement Cooling of a Semi-Spherical Concave Surface Covered by Porous Medium with a Jet Trapping Hole

2014 ◽  
Vol 348 ◽  
pp. 162-170
Author(s):  
Pey Shey Wu ◽  
Yi Hung Lin ◽  
Yue Hua Jhuo ◽  
Hsiao Ying Chan
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Porous Material ◽  
Target Surface ◽  
Temperature Fields ◽  
Concave Surface ◽  
Far Field ◽  
Impingement Heat Transfer ◽  
Plate Distance

Impingement heat transfer between a circular jet and a semi-spherical concave surface with or without coverage of porous material is investigated experimentally and numerically. For cases with coverage of the porous material on the target plate, a trapping hole for the jet fluid is fabricated. Measured local Nusselt number distributions along a meridian are documented. The flow and temperature fields at the conditions similar to that of experiments were computed with CFD software to support the experimental results and help to explain the physics. Varying parameters include Reynolds number, nozzle-to-plate distance, relative curvature, and a target surface with or without the covered porous material. Results show that the attachment of a porous material increases Nusselt number, with more influence at the stagnation zone than the far field. Increasing Reynolds number usually increases Nusselt number unless it is too high. Although an increase in the nozzle-to-plate distance decreases stagnation Nusselt number, the influence in heat transfer is small in the far field. The trapping-hole diameter should be the same as that of the jet diameter for best heat transfer enhancement.

Heat Transfer Enhancement in Axial Taylor-Couette Flow

2005 ◽  
Author(s):  
S. Gilchrist ◽  
C. Y. Ching ◽  
D. Ewing
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Couette Flow ◽  
Reynolds Numbers ◽  
Taylor Number ◽  
Number Range ◽  
Taylor Couette ◽  
Number Case ◽  
Taylor Couette Flow

An experimental investigation was performed to determine the effect that surface roughness has on the heat transfer in an axial Taylor-Couette flow. The experiments were performed using an inner rotating cylinder in a stationary water jacket for Taylor numbers of 106 to 5×107 and axial Reynolds numbers of 900 to 2100. Experiments were performed for a smooth inner cylinder, a cylinder with two-dimensional rib roughness and a cylinder with three-dimensional cubic protrusions. The heat transfer results for the smooth cylinder were in good agreement with existing experimental data. The change in the Nusselt number was relatively independent of the axial Reynolds number for the cylinder with rib roughness. This result was similar to the smooth wall case but the heat transfer was enhanced by 5% to 40% over the Taylor number range. The Nusselt number for the cylinder with cubic protrusions exhibited an axial Reynolds number dependence. For a low axial Reynolds number of 980, the Nusselt number increased with the Taylor number in a similar way to the other test cylinders. At higher axial Reynolds numbers, the heat transfer was initially independent of the Taylor number before increasing with Taylor number similar to the lower Reynolds number case. In this higher axial Reynolds number case the heat transfer was enhanced by up to 100% at the lowest Taylor number of 1×106 and by approximately 35% at the highest Taylor number of 5×107.

Experimental Investigations on Heat Transfer Enhancement in a Horizontal Tube Using Converging and Diverging Conical Strips

2014 ◽  
Author(s):  
Naga Sarada Somanchi ◽  
Sri Rama Devi Rangisetty ◽  
Sudheer PremKumar Bellam ◽  
Ravi Gugulothu ◽  
Samuel Bellam
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Circular Tube ◽  
Horizontal Tube ◽  
Working Fluid ◽  
Experimental Investigations ◽  
Transfer Enhancement ◽  
Enhancement Of Heat Transfer ◽  
Plain Tube ◽  
Flow Heat

The present work deals with the results of the experimental investigations carried out on augmentation of turbulent flow heat transfer in a horizontal circular tube by means of tube inserts, with air as working fluid. Experiments were carried out initially for the plain tube (without tube inserts). The Nusselt number and friction factor obtained experimentally were validated against those obtained from theoretical correlations. Secondly experimental investigations using six kinds of tube inserts namely Rectangular bar with diverging conical strips, Rectangular bar with converging conical strips, Rectangular bar with alternate converging diverging conical strips, Rectangular bar with holes and diverging conical strips, Rectangular bar with holes and converging conical strips and Rectangular bar with holes and alternate converging diverging conical strips were carried out to estimate the enhancement of heat transfer rate for air in the presence of inserts. The Reynolds number ranged from 8000 to 19000. In the presence of inserts, Nusselt number and pressure drop increased, overall enhancement ratio is calculated to determine the optimum geometry of the tube insert. Based on experimental investigations, it is observed that, the enhancement of heat transfer using Rectangular bar with diverging conical strips is more effective compared to other inserts.

scholarly journals Experimental Investigation of The Influence of Mechanical Forced Vibrations and Heat Flux on Coefficient of Heat Transfer

2018 ◽  
Vol 6 (3) ◽  
pp. 124-129
Author(s):  
Adil Bash ◽  
Aadel Alkumait ◽  
Hamza Yaseen
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Reynolds Number ◽  
Forced Vibration ◽  
Vibration Amplitude ◽  
Internal Flow ◽  
Reynolds Numbers ◽  
Constant Heat Flux ◽  
Working Fluid ◽  
New Correlation

The aim of this paper to verify the influence of vertical forced vibration on the coefficient of heat transfer of the laminar internal flow in a spiral fluted tube. With adopted the water as a working fluid, and flowing Reynolds numbers at the entrance between 228 and 1923, the tube heated under constant heat flux levels ranging from 618-3775 W/m2. The frequencies of vibration ranging from 13 to 30 Hz, and the amplitudes of vibration from 0.001 to 0.002 mm. The results appeared that the coefficient of heat transfer significantly affected by mechanical forced vibration in a flowing of the heated tube. When the vibration amplitude increases, the Nusselt number Significantly increases, with the maximum increases of 8.4% at the amplitude of vibration 0.0022 mm and the frequency 13 Hz. Generally, the coefficient of heat transfer increases with increasing Reynolds number and heat flux. At last, by using the parameters of vibration amplitude, frequency, heat flux and Reynolds number, a new correlation has been derived depends on experimental data.

Sign in / Sign up

Export Citation Format

Share Document