Finite Element Analysis of Dynamic Coupled Thermoelasticity Problems With Relaxation Times

1983 ◽  
Vol 50 (4a) ◽  
pp. 817-822 ◽  
Author(s):  
J. H. Prevost ◽  
D. Tao
Keyword(s):  
Finite Element ◽  
Classical Model ◽  
Relaxation Times ◽  
Time Integration ◽  
Propagation Speed ◽  
Element Model ◽  
Stress Wave Propagation ◽  
Element Analysis ◽  
Transient Phenomena ◽  
Coupled Thermoelasticity Problems

A general finite element model is proposed to analyze transient phenomena in thermoelastic solids. Green and Lindsay’s dynamic thermoelasticity model is selected for that purpose since it allows for “second sound” effects and reduces to the classical model by appropriate choice of the parameters. Time integration of the semidiscrete finite element equations is achieved by using an implicit-explicit scheme proposed by Hughes, et al. The procedure proves to be most effective and versatile in thermal and stress wave propagation analysis. A number of examples are presented which demonstrate the accuracy and versatility of the proposed model, and the importance of finite thermal propagation speed effects.

A Finite Element Analysis for Unbonded Flexible Risers Under Torsion

2007 ◽  
Author(s):  
A. Bahtui ◽  
H. Bahai ◽  
G. Alfano
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Numerical Model ◽  
Finite Element Model ◽  
Time Integration ◽  
Element Model ◽  
Integration Scheme ◽  
Element Analysis ◽  
Benchmark Solutions ◽  
The Finite Element Model

This paper presents a detailed finite element analysis of a five-layer unbonded flexible riser. The numerical results are compared analytical solutions for various load cases. In the finite element model all layers are modelled separately with contact interfaces placed between each layer. The finite element model includes the main features of the riser geometry with very little simplifying assumptions made. The numerical model was solved using a fully explicit time-integration scheme implemented in a parallel environment on a 16-processor cluster. The very good agreement found from numerical and analytical comparisons validates the use of our numerical model to provide benchmark solutions against which further detailed investigation will be made.

A Finite Element Analysis for Unbonded Flexible Risers Under Axial Tension

2008 ◽  
Author(s):  
Ali Bahtui ◽  
Hamid Bahai ◽  
Giulio Alfano
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Time Integration ◽  
Element Model ◽  
Integration Scheme ◽  
Element Analysis ◽  
Time Integration Scheme ◽  
Flexible Risers ◽  
Benchmark Solutions ◽  
The Finite Element Model

Recent developments on the numerical analysis of detailed finite element models of unbonded flexible risers using ABAQUS are presented. Several analytical methods are studied and combined together, and their results are compared with those obtained in the finite element model for two different tests, the second one involving cyclic loading. In the finite element model all layers are modeled separately and contact interfaces are placed between each layer. A fully explicit time-integration scheme was used on a 16-processor cluster. The very good agreement found from numerical and analytical comparisons validates the use of our numerical model to provide benchmark solutions against which further detailed investigation will be made.

Numerical and Analytical Modeling of Unbonded Flexible Risers

2009 ◽  
Vol 131 (2) ◽  
Author(s):  
A. Bahtui ◽  
H. Bahai ◽  
G. Alfano
Keyword(s):  
Finite Element ◽  
Time Integration ◽  
Computational Cost ◽  
Element Model ◽  
Integration Scheme ◽  
Element Analysis ◽  
Axial Tension ◽  
External Pressures ◽  
Time Integration Scheme ◽  
Flexible Risers

This paper presents an analytical formulation and a finite element analysis of the behavior of multilayer unbonded flexible risers. The finite element model accurately incorporates all the fine details of the riser that were previously considered to be important but too difficult to simulate due to the significant associated computational cost. All layers of the riser are separately modeled, and contact interaction between layers has been accounted for. The model includes geometric nonlinearity as well as frictional effects. The analysis considers the main modes of flexible riser loading, which include internal and external pressures, axial tension, torsion, and bending. Computations were performed by employing a fully explicit time integration scheme on a parallel 16-processor cluster of computers. Consistency of simulation results was demonstrated by comparison with those of the analytical model of an identical structure. The close agreement gives confidence in both approaches.

КОНСТРУКТИВНО-ТЕХНОЛОГІЧНІ ОСОБЛИВОСТІ ХВОСТО-ВИХ БАЛОК СІТЧАСТОГО ТИПУ З ПОЛІМЕРНИХ КОМПО-ЗИЦІЙНИХ МАТЕРІАЛІВ ВЕРТОЛЬОТІВ ТРАНСПОРТНОЇ КАТЕГОРІЇ

2020 ◽  
pp. 15-30
Author(s):  
А. Г. Гребеников ◽  
И. В. Малков ◽  
В. А. Урбанович ◽  
Н. И. Москаленко ◽  
Д. С. Колодийчик
Keyword(s):  
Finite Element ◽  
Strain State ◽  
Layer Structure ◽  
Metal Structure ◽  
Element Model ◽  
Stress Strain ◽  
Element Analysis ◽  
Mesh Structure ◽  
Stress Strain State ◽  
Mesh Structures

The analysis of the design and technological features of the tail boom (ТB) of a helicopter made of polymer composite materials (PCM) is carried out.Three structural and technological concepts are distinguished - semi-monocoque (reinforced metal structure), monocoque (three-layer structure) and mesh-type structure. The high weight and economic efficiency of mesh structures is shown, which allows them to be used in aerospace engineering. The physicomechanical characteristics of the network structures are estimated and their uniqueness is shown. The use of mesh structures can reduce the weight of the product by a factor of two or more.The stress-strain state (SSS) of the proposed tail boom design is determined. The analysis of methods for calculating the characteristics of the total SSS of conical mesh shells is carried out. The design of the tail boom is presented, the design diagram of the tail boom of the transport category rotorcraft is developed. A finite element model was created using the Siemens NX 7.5 system. The calculation of the stress-strain state (SSS) of the HC of the helicopter was carried out on the basis of the developed structural scheme using the Advanced Simulation module of the Siemens NX 7.5 system. The main zones of probable fatigue failure of tail booms are determined. Finite Element Analysis (FEA) provides a theoretical basis for design decisions.Shown is the effect of the type of technological process selected for the production of the tail boom on the strength of the HB structure. The stability of the characteristics of the PCM tail boom largely depends on the extent to which its design is suitable for the use of mechanized and automated production processes.A method for the manufacture of a helicopter tail boom from PCM by the automated winding method is proposed. A variant of computer modeling of the tail boom of a mesh structure made of PCM is shown.The automated winding technology can be recommended for implementation in the design of the composite tail boom of the Mi-2 and Mi-8 helicopters.

Torsional Analysis of a Steel Cord-Rubber Tire Belt Structure

1996 ◽  
Vol 24 (4) ◽  
pp. 339-348 ◽  
Author(s):  
R. M. V. Pidaparti
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Composite Structures ◽  
Three Dimensional ◽  
Element Model ◽  
Torsional Stiffness ◽  
Element Analysis ◽  
Rubber Belt ◽  
Steel Cord ◽  
Torsional Analysis

Abstract A three-dimensional (3D) beam finite element model was developed to investigate the torsional stiffness of a twisted steel-reinforced cord-rubber belt structure. The present 3D beam element takes into account the coupled extension, bending, and twisting deformations characteristic of the complex behavior of cord-rubber composite structures. The extension-twisting coupling due to the twisted nature of the cords was also considered in the finite element model. The results of torsional stiffness obtained from the finite element analysis for twisted cords and the two-ply steel cord-rubber belt structure are compared to the experimental data and other alternate solutions available in the literature. The effects of cord orientation, anisotropy, and rubber core surrounding the twisted cords on the torsional stiffness properties are presented and discussed.

Finite Element Analysis of Nonuniformity of Tires with Imperfections5

2007 ◽  
Vol 35 (3) ◽  
pp. 226-238 ◽  
Author(s):  
K. M. Jeong ◽  
K. W. Kim ◽  
H. G. Beom ◽  
J. U. Park
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Radial Force ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Dimensional Finite Element ◽  
Force Variation ◽  
Three Dimensional Finite Element

Abstract The effects of variations in stiffness and geometry on the nonuniformity of tires are investigated by using the finite element analysis. In order to evaluate tire uniformity, a three-dimensional finite element model of the tire with imperfections is developed. This paper considers how imperfections, such as variations in stiffness or geometry and run-out, contribute to detrimental effects on tire nonuniformity. It is found that the radial force variation of a tire with imperfections depends strongly on the geometrical variations of the tire.

Finite Element Analysis of Tire/Rim Interface Forces Under Braking and Cornering Loads

1992 ◽  
Vol 20 (2) ◽  
pp. 83-105 ◽  
Author(s):  
J. P. Jeusette ◽  
M. Theves
Keyword(s):  
Finite Element ◽  
Shear Stress ◽  
Contact Pressure ◽  
Element Model ◽  
Shear Stresses ◽  
Detailed Knowledge ◽  
Stress Distributions ◽  
Element Analysis ◽  
Plane Shear ◽  
Normal Contact

Abstract During vehicle braking and cornering, the tire's footprint region may see high normal contact pressures and in-plane shear stresses. The corresponding resultant forces and moments are transferred to the wheel. The optimal design of the tire bead area and the wheel requires a detailed knowledge of the contact pressure and shear stress distributions at the tire/rim interface. In this study, the forces and moments obtained from the simulation of a vehicle in stationary braking/cornering conditions are applied to a quasi-static braking/cornering tire finite element model. Detailed contact pressure and shear stress distributions at the tire/rim interface are computed for heavy braking and cornering maneuvers.

Redrawing Operation a Star Shape from Cylindrical Shape Using Experimental and FE Analysis

2020 ◽  
Vol 38 (1A) ◽  
pp. 25-32
Author(s):  
Waleed Kh. Jawad ◽  
Ali T. Ikal
Keyword(s):  
Finite Element ◽  
Effective Strain ◽  
Element Model ◽  
Cylindrical Shape ◽  
Element Analysis ◽  
Punch Force ◽  
Maximum Value ◽  
Element Simulation ◽  
Blank Sheet ◽  
The Finite Element Model

The aim of this paper is to design and fabricate a star die and a cylindrical die to produce a star shape by redrawing the cylindrical shape and comparing it to the conventional method of producing a star cup drawn from the circular blank sheet using experimental (EXP) and finite element simulation (FES). The redrawing and drawing process was done to produce a star cup with the dimension of (41.5 × 34.69mm), and (30 mm). The finite element model is performed via mechanical APDL ANSYS18.0 to modulate the redrawing and drawing operation. The results of finite element analysis were compared with the experimental results and it is found that the maximum punch force (39.12KN) recorded with the production of a star shape drawn from the circular blank sheet when comparing the punch force (32.33 KN) recorded when redrawing the cylindrical shape into a star shape. This is due to the exposure of the cup produced drawn from the blank to the highest tensile stress. The highest value of the effective stress (709MPa) and effective strain (0.751) recorded with the star shape drawn from a circular blank sheet. The maximum value of lamination (8.707%) is recorded at the cup curling (the concave area) with the first method compared to the maximum value of lamination (5.822%) recorded at the cup curling (the concave area) with the second method because of this exposure to the highest concentration of stresses. The best distribution of thickness, strains, and stresses when producing a star shape by

scholarly journals Comparison of Tooth- and Bone-Borne Appliances on the Stress Distributions and Displacement Patterns in the Facial Skeleton in Surgically Assisted Rapid Maxillary Expansion—A Finite Element Analysis (FEA) Study

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1152
Author(s):  
Rafał Nowak ◽  
Anna Olejnik ◽  
Hanna Gerber ◽  
Roman Frątczak ◽  
Ewa Zawiślak
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Rapid Maxillary Expansion ◽  
Stress Distributions ◽  
Maxillary Expansion ◽  
Facial Skeleton ◽  
Element Analysis ◽  
Maxillary Constriction

The aim of this study was to compare the reduced stresses according to Huber’s hypothesis and the displacement pattern in the region of the facial skeleton using a tooth- or bone-borne appliance in surgically assisted rapid maxillary expansion (SARME). In the current literature, the lack of updated reports about biomechanical effects in bone-borne appliances used in SARME is noticeable. Finite element analysis (FEA) was used for this study. Six facial skeleton models were created, five with various variants of osteotomy and one without osteotomy. Two different appliances for maxillary expansion were used for each model. The three-dimensional (3D) model of the facial skeleton was created on the basis of spiral computed tomography (CT) scans of a 32-year-old patient with maxillary constriction. The finite element model was built using ANSYS 15.0 software, in which the computations were carried out. Stress distributions and displacement values along the 3D axes were found for each osteotomy variant with the expansion of the tooth- and the bone-borne devices at a level of 0.5 mm. The investigation showed that in the case of a full osteotomy of the maxilla, as described by Bell and Epker in 1976, the method of fixing the appliance for maxillary expansion had no impact on the distribution of the reduced stresses according to Huber’s hypothesis in the facial skeleton. In the case of the bone-borne appliance, the load on the teeth, which may lead to periodontal and orthodontic complications, was eliminated. In the case of a full osteotomy of the maxilla, displacements in the buccolingual direction for all the variables of the bone-borne appliance were slightly bigger than for the tooth-borne appliance.

scholarly journals Development of Simulation Based p-Multipliers for Laterally Loaded Pile Groups in Granular Soil Using 3D Nonlinear Finite Element Model

2020 ◽  
Vol 11 (1) ◽  
pp. 26
Author(s):  
Muhammad Bilal Adeel ◽  
Muhammad Asad Jan ◽  
Muhammad Aaqib ◽  
Duhee Park
Keyword(s):  
Finite Element ◽  
Element Model ◽  
Design Guidelines ◽  
American Petroleum Institute ◽  
Winkler Foundation ◽  
Group Effect ◽  
Pile Groups ◽  
Element Analysis ◽  
Laterally Loaded Pile ◽  
Laterally Loaded

The behavior of laterally loaded pile groups is usually accessed by beam-on-nonlinear-Winkler-foundation (BNWF) approach employing various forms of empirically derived p-y curves and p-multipliers. Averaged p-multiplier for a particular pile group is termed as the group effect parameter. In practice, the p-y curve presented by the American Petroleum Institute (API) is most often utilized for piles in granular soils, although its shortcomings are recognized. In this study, we performed 3D finite element analysis to develop p-multipliers and group effect parameters for 3 × 3 to 5 × 5 vertically squared pile groups. The effect of the ratio of spacing to pile diameter (S/D), number of group piles, varying friction angle (φ), and pile fixity conditions on p-multipliers and group effect parameters are evaluated and quantified. Based on the simulation outcomes, a new functional form to calculate p-multipliers is proposed for pile groups. Extensive comparisons with the experimental measurements reveal that the calculated p-multipliers and group effect parameters are within the recorded range. Comparisons with two design guidelines which do not account for the pile fixity condition demonstrate that they overestimate the p-multipliers for fixed-head condition.

Sign in / Sign up

Export Citation Format

Share Document