Effect of Fuel Injection Timing and Injection Pressure on Combustion and Odorous Emissions in DI Diesel Engines

2009 ◽  
Vol 131 (3) ◽  
Author(s):  
Murari Mohon Roy
Keyword(s):  
Ignition Delay ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection Pressure ◽  
Injection Timing ◽  
Cylinder Pressure ◽  
Warm Up ◽  
Fuel Injection Timing ◽  
Peak Cylinder Pressure ◽  
Injection Pressures

This study investigated the effect of fuel injection timing and injection pressure on combustion and odorous emissions in a direct injection diesel engine. Injection timings from 15 deg before top dead center (BTDC) to top dead center (TDC) and injection pressures from 20 MPa to 120 MPa were tested. In emissions, exhaust odor, irritation, aldehydes, total hydrocarbon, and hydrocarbon components are compared in different injection timings and injection pressures condition. Injection timings where main combustion takes place very close to TDC are found to show minimum odorous emissions. Moderate injection pressures (60–80 MPa) showed lower emissions including odor and irritation due to proper mixture formation. Below the injection pressure of 40 MPa, and over 80 MPa, emissions become worse. Combustion analysis is performed by taking cylinder pressures after engine warm-up for different injection timings and injection pressures and analyzing cylinder temperatures and heat release rates. Cylinder pressures and temperatures are gradually decreased when injection timings are retarded. Ignition delay becomes shortest at 5–10 deg BTDC injection timings. The peak cylinder pressure and temperature are increased with higher injection pressures. The shortest ignition delay and minimum emissions is found at around 60 MPa of injection pressure.

Effect of Injection Timing on Performance, Combustion and Emission Characteristics of Dairy Scum Methyl Esters in CRDI Engine

2020 ◽  
Vol 12 (4) ◽  
Author(s):  
M. Nandeesh ◽  
R. Harishkumar ◽  
C.R. Rajashekar ◽  
N.R. Banapurmath ◽  
V.S. Yaliwal
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Methyl Esters ◽  
Direct Injection ◽  
Injection Pressure ◽  
Injection Timing ◽  
Emission Characteristics ◽  
Single Cylinder ◽  
Diesel Fuels ◽  
Fuel Injection Timing

The conventional diesel fuels are depleting at a faster pace. To reduce the burden on the economy, the reserves and sources for future has to be limited. The use of biodiesel derivatives from various sources and its blends in diesel engine has gained more importance in recent years. The present work investigates the feasibility of using dairy scum methyl esters (DSOME) of B20 blend in a modified single cylinder of common rail direct injection (CRDI) engine at a constant speed. Experiments were carried out at different injection timings from 25deg BTDC to 5deg ATDC with constant injection pressure as 600 bar. The fuel injection timing plays an important role in evaluating the performance, emission and combustion characteristics of the engine. The results show that the performance is improved with retarded injection timings compared to the operation of single cylinder DI engine fuelled with DSOME B20 biodiesel.

Combustion Characteristics of Methane Direct Injection Engine Under Various Injection Timings and Injection Pressures

2016 ◽  
Author(s):  
Jingeun Song ◽  
Mingi Choi ◽  
Daesik Kim ◽  
Sungwook Park
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Injection Pressure ◽  
Combustion Characteristics ◽  
Injection Timing ◽  
Direct Injection Engine ◽  
Optical Engine ◽  
Start Of Injection ◽  
Crank Angle ◽  
Injection Pressures

The performance of a methane direct injection engine was investigated under various fuel injection timings and injection pressures. A single-cylinder optical engine was used to acquire in-cylinder pressure data and flame images. An outward-opening injector was installed at the center of the cylinder head. Experimental results showed that the combustion characteristics were strongly influenced by the end of injection timing rather than the start of injection timing. Late injection enhanced the combustion speed because the short duration between the end of injection and the spark induced strong turbulence. The flame propagation speeds under various injection timings were directly compared using crank-angle-resolved sequential flame images. The injection pressure was not an important factor in the combustion; the three injection pressure cases of 0.5, 0.8, and 1.1 MPa yielded similar combustion trends. In the cases of late injection, the injection timings of which were near the Intake Valve Closing (IVC) timing, the volumetric efficiency was higher (by 4%) than in the earlier injection cases. This result implies that the methane direct injection engine can achieve higher torque by means of the late injection strategy.

Effect of Injection Timing on Combustion Characteristics of a DI Diesel Engine Fuelled with Pistacia chinensis Bunge Seed Biodiesel

2012 ◽  
Vol 614-615 ◽  
pp. 337-342
Author(s):  
Li Luo ◽  
Bin Xu ◽  
Zhi Hao Ma ◽  
Jian Wu ◽  
Ming Li
Keyword(s):  
Combustion Temperature ◽  
Fuel Injection ◽  
Direct Injection ◽  
Combustion Characteristics ◽  
Injection Timing ◽  
Brake Specific Fuel Consumption ◽  
Cylinder Pressure ◽  
Combustion Duration ◽  
Di Diesel Engine ◽  
Maximum Combustion Temperature

In this study, the effect of injection timing on combustion characteristics of a direct injection, electronically controlled, high pressure, common rail, turbocharged and intercooled engine fuelled with different pistacia chinensis bunge seed biodiesel/diesel blends has been experimentally investigated. The results indicated that brake specific fuel consumption reduces with the increasing of fuel injection advance angle and enhances with the increasing of biodiesel content in the blends. The peak of cylinder pressure and maximum combustion temperature increase evidently with the increment of fuel injection advance angle. However, the combustion of biodiesel blends starts earlier than diesel at the same fuel injection advance angle. At both conditions, the combustion duration and the peak of heat release rate are insensitive to the changing of injection timing.

scholarly journals A Study of Combustion Characteristics of Two Gasoline–Biodiesel Mixtures on RCEM Using Various Fuel Injection Pressures

Energies ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 3265
Author(s):  
Ardhika Setiawan ◽  
Bambang Wahono ◽  
Ocktaeck Lim
Keyword(s):  
Heat Release ◽  
Ignition Delay ◽  
Fuel Injection ◽  
Injection Pressure ◽  
Fuel Mixture ◽  
Injection Rate ◽  
Injection Duration ◽  
Late Start ◽  
Fuel Injection Rate ◽  
Injection Pressures

Experimental research was conducted on a rapid compression and expansion machine (RCEM) that has characteristics similar to a gasoline compression ignition (GCI) engine, using two gasoline–biodiesel (GB) blends—10% and 20% volume—with fuel injection pressures varying from 800 to 1400 bar. Biodiesel content lower than GB10 will result in misfires at fuel injection pressures of 800 bar and 1000 bar due to long ignition delays; this is why GB10 was the lowest biodiesel blend used in this experiment. The engine compression ratio was set at 16, with 1000 µs of injection duration and 12.5 degree before top dead center (BTDC). The results show that the GB20 had a shorter ignition delay than the GB10, and that increasing the injection pressure expedited the autoignition. The rate of heat release for both fuel mixes increased with increasing fuel injection pressure, although there was a degradation of heat release rate for the GB20 at the 1400-bar fuel injection rate due to retarded in-cylinder peak pressure at 0.24 degree BTDC. As the ignition delay decreased, the brake thermal efficiency (BTE) decreased and the fuel consumption increased due to the lack of air–fuel mixture homogeneity caused by the short ignition delay. At the fuel injection rate of 800 bar, the GB10 showed the worst efficiency due to the late start of combustion at 3.5 degree after top dead center (ATDC).

Experimental and Numerical Analysis on the Influence of Direct Fuel Injection Into O2-Depleted Environment of a GDI-HCCI Engine

2020 ◽  
Author(s):  
Ratnak Sok ◽  
Jin Kusaka
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Injection Pressure ◽  
Single Pulse ◽  
Gasoline Direct Injection ◽  
Injection Timing ◽  
Rich Mixture ◽  
Intake Stroke ◽  
Shift Reaction ◽  
Direct Fuel Injection

Abstract Injected gasoline into the O2-depleted environment in the recompression stroke can be converted into light hydrocarbons due to thermal cracking, partial oxidation, and water-gas shift reaction. These reformate species influence the combustion phenomena of gasoline direct injection homogeneous charge compression ignition (GDI-HCCI) engines. In this work, a production-based single-cylinder research engine was boosted to reach IMEPn = 0.55 MPa in which its indicated efficiency peaks at 40–41%. Experimentally, the main combustion phases are advanced under single-pulse direct fuel injection into the negative valve overlap (NVO) compared with that of the intake stroke. NVO peak in-cylinder pressures are lower than that of motoring, which emphasizes that endothermic reaction occurs during the interval. Low O2 concentration could play a role in this evaporative charge cooling effect. This phenomenon limits the oxidation reaction, and the thermal effect is not pronounced. For understanding the recompression reaction phenomena, 0D simulation with three different chemical reaction mechanisms is studied to clarify that influences of direct injection timing in NVO on combustion advancements are kinetically limited by reforming. The 0D results show the same increasing tendencies of classical reformed species of rich-mixture such as C3H6, C2H4, CH4, CO, and H2 as functions of injection timings. By combining these reformed species into the main fuel-air mixture, predicted ignition delays are shortened. The effects of the reformed species on the main combustion are confirmed by 3D-CFD calculation, and the results show that OH radical generation is advanced under NVO fuel injection compared with that of intake stroke conditions thus earlier heat release and cylinder pressure are noticeable. Also, parametric studies on injection pressure and double-pulse injections on engine combustion are performed experimentally.

Effect of Fuel Injection Timing Relative to Ignition Timing on the Natural-Gas Direct-Injection Combustion

2001 ◽  
Author(s):  
Zuohua Huang ◽  
Seiichi Shiga ◽  
Takamasa Ueda ◽  
Nobuhisa Jingu ◽  
Hisao Nakamura ◽  
...  
Keyword(s):  
Heat Release ◽  
Late Stage ◽  
Equivalence Ratio ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection Timing ◽  
Ignition Timing ◽  
Fuel Injection Timing ◽  
Initial Stage ◽  
Wide Range

Abstract Effect of fuel injection timing relative to ignition timing on natural gas direct-injection combustion was studied by using a rapid compression machine. The ignition timing was fixed at 80 ms from the compression start. When the injection timing was relatively earlier (injection start at 60 ms), the heat release pattern showed slower burn in the initial stage and faster burn in the late stage, which is similar to that of flame propagation of a premixed gas. In contrast to this, when the injection timing was relatively later (injection start at 75 ms), the heat release rate showed faster burn in the initial stage and slower burn in the late stage, which is similar to that of diesel combustion. The shortest duration was realized at the injection end timing of 80 ms (the same timing as the ignition timing) over the wide range of equivalence ratio. The degree of charge stratification and the intensity of turbulence generated by the fuel jet is considered to cause these behaviors. Earlier injection leads to longer duration of the initial combustion, whereas the later injection does longer duration of the late combustion. Earlier injection showed relatively lower CO emission while later injection produces relatively lower NOx emission. It was suggested that earlier injection leads to lower mixture stratification combustion and later injection leads to higher mixture stratification combustion. Combustion efficiency maintained high value over the wide range of equivalence ratio.

Evaluation of the combustion-induced noise and vibration using coherence and wavelet coherence estimates in a diesel engine

2019 ◽  
pp. 146808741987854
Author(s):  
Hossein Ahmadian ◽  
Gholamhassan Najafi ◽  
Barat Ghobadian ◽  
Seyed Reza Hassan-Beygi ◽  
Seyed Salar Hoseini
Keyword(s):  
Diesel Engine ◽  
Sound Pressure ◽  
Fuel Injection ◽  
Direct Injection ◽  
Wavelet Coherence ◽  
Injection Timing ◽  
Cylinder Pressure ◽  
Noise And Vibration ◽  
Four Levels ◽  
Wavelet Coherency

The understanding of noise generation and source identification is vital in noise control. This research was conducted to experimentally evaluate combustion-induced noise and vibration using coherence and wavelet coherence estimates. A single-cylinder direct-injection diesel engine was chosen for experimental investigation. The independent variables for conducting experiments were injection timing with five levels of 22, 27, 32 (normal), 37, and 42 crank angles before the top dead center, and also the engine torque load with four levels of 55%, 70%, 85%, and 100% of the rated value. The signals of cylinder pressure, liner acceleration, and radiated sound pressure of the test engine were measured and recorded. Then, coherency and wavelet coherency experiments were carried out between cylinder pressure and liner acceleration, cylinder pressure and sound pressure, and liner acceleration and sound pressure signals in MATLAB software. The results indicated that increasing load would increase wavelet coherency between cylinder pressure and liner acceleration signals at frequencies higher than 1 kHz. The coherent regions between cylinder pressure and sound pressure signals were mainly at frequencies higher than 1 kHz while advancing the fuel injection timing had shifted the coherency toward lower frequencies. In general, with advancing injection timing, the coherent regions between liner acceleration and sound pressure signals have appeared at broader time ranges, especially at frequencies between 100 and 500 Hz. Comparing the results of the wavelet coherency and coherency tests, we concluded that wavelet coherency is a more accurate and descriptive tool in evaluating the combustion-induced noise and vibration.

Effect of Fuel Injection Timing During Negative Valve Overlap Period on a GDI-HCCI Engine

2018 ◽  
Author(s):  
Sok Ratnak ◽  
Jin Kusaka ◽  
Yasuhiro Daisho ◽  
Kei Yoshimura ◽  
Kenjiro Nakama
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Single Pulse ◽  
Injection Timing ◽  
Pulse Injection ◽  
Hcci Combustion ◽  
Fuel Injection Timing ◽  
Intake Stroke ◽  
Negative Valve Overlap ◽  
Valve Overlap

Gasoline Direct Injection Homogeneous Charge Compression (GDI-HCCI) combustion is achieved by closing early the exhaust valves for trapping hot residual gases combined with direct fuel injection. The combustion is chemically controlled by multi-point auto-ignition which its main combustion phase can be controlled by direct injection timing of fuel. This work investigates the effect of single pulse injection timing on a supercharged GDI-HCCI combustion engine by using a four-stroke single cylinder engine with a side-mounted direct fuel injector. Injection of primary reference fuel PRF90 under the near-stoichiometric-boosted condition is studied. The fuel is injected during negative valve overlap (NVO) or recompression period for fuel reformation under low oxygen concentration and the injection is retarded to intake stroke for the homogeneous mixture. It is found that the early fuel injection in NVO period advances the combustion phasing compared with the retarded injection in the intake stroke. Noticeable slower combustion rate from intake stroke fuel injection is obtained compared with the NVO injection due to charge cooling effect. Zero-dimensional combustion simulations with multiple chemical reaction mechanisms are simulated to provide chemical understanding from the effect of fuel injection timing on intermediate species generations. The species such as C2H4, C3H6, CH4, and H2 are found to be formed during the NVO injection period from the calculations. The effects of single pulse injection timings on combustion characteristics such pressure rise rate, combustion stability, and emissions are also discussed in this study.

Combustion Characteristics of Methane Direct Injection Engine Under Various Injection Timings and Injection Pressures

2017 ◽  
Vol 139 (8) ◽  
Author(s):  
Jingeun Song ◽  
Mingi Choi ◽  
Daesik Kim ◽  
Sungwook Park
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Injection Pressure ◽  
Combustion Characteristics ◽  
Direct Injection Engine ◽  
Optical Engine ◽  
Start Of Injection ◽  
Crank Angle ◽  
Combustion Speed ◽  
Injection Pressures

The performance of a methane direct injection engine was investigated under various fuel injection timings and injection pressures. A single-cylinder optical engine was used to acquire in-cylinder pressure data and flame images. An outward-opening injector was installed at the center of the cylinder head. Experimental results showed that the combustion characteristics were strongly influenced by the end of injection (EOI) timing rather than the start of injection (SOI) timing. Late injection enhanced the combustion speed because the short duration between the end of injection and the spark-induced strong turbulence. The flame propagation speeds under various injection timings were directly compared using crank-angle-resolved sequential flame images. The injection pressure was not an important factor in the combustion; the three injection pressure cases of 0.5, 0.8, and 1.1 MPa yielded similar combustion trends. In the cases of late injection, the injection timings of which were near the intake valve closing (IVC) timing, the volumetric efficiency was higher (by 4%) than in the earlier injection cases. This result implies that the methane direct injection engine can achieve higher torque by means of the late injection strategy.

Distribution of Two-Stage Direct Injection CNG-Air Mixture near Lean Limit Using CFD

2013 ◽  
Vol 465-466 ◽  
pp. 448-452
Author(s):  
Mas Fawzi ◽  
Bukhari Manshoor ◽  
Yoshiyuki Kidoguchi ◽  
Yuzuru Nada
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Engine Performance ◽  
Injection Pressure ◽  
Gas Jet ◽  
Exhaust Emission ◽  
Injection Technique ◽  
Injection Timing ◽  
Two Stage ◽  
Lean Burn

Previous work shows that gas-jet ignition with two-stage injection technique is effective to extend lean combustible ranges of CNG engines. In this report, the robustness of the gas-jet ignition with two-stage injection method was investigated purposely to improve the performance of a lean burn direct injection CNG engine. The experiment was conducted using an engine at speed of 900 rpm, fuel-injection-pressure of 3MPa, equivalence ratio at 0.8, and ignition timing at top dead center. The effect of first injection timing on the test engine performance and exhaust emission was analyzed. First injection timings near the gas-jet ignition produced unstable combustion with occurrence of misfires except at a timing which produced distinctively good combustion with low HC and CO emissions. Computational fluid dynamics was used to provide hindsight of the fuel-air mixture distribution that might be the cause of misfires occurrence at certain injection timings.

Sign in / Sign up

Export Citation Format

Share Document