Evaluation of the combustion-induced noise and vibration using coherence and wavelet coherence estimates in a diesel engine

2019 ◽  
pp. 146808741987854
Author(s):  
Hossein Ahmadian ◽  
Gholamhassan Najafi ◽  
Barat Ghobadian ◽  
Seyed Reza Hassan-Beygi ◽  
Seyed Salar Hoseini
Keyword(s):  
Diesel Engine ◽  
Sound Pressure ◽  
Fuel Injection ◽  
Direct Injection ◽  
Wavelet Coherence ◽  
Injection Timing ◽  
Cylinder Pressure ◽  
Noise And Vibration ◽  
Four Levels ◽  
Wavelet Coherency

The understanding of noise generation and source identification is vital in noise control. This research was conducted to experimentally evaluate combustion-induced noise and vibration using coherence and wavelet coherence estimates. A single-cylinder direct-injection diesel engine was chosen for experimental investigation. The independent variables for conducting experiments were injection timing with five levels of 22, 27, 32 (normal), 37, and 42 crank angles before the top dead center, and also the engine torque load with four levels of 55%, 70%, 85%, and 100% of the rated value. The signals of cylinder pressure, liner acceleration, and radiated sound pressure of the test engine were measured and recorded. Then, coherency and wavelet coherency experiments were carried out between cylinder pressure and liner acceleration, cylinder pressure and sound pressure, and liner acceleration and sound pressure signals in MATLAB software. The results indicated that increasing load would increase wavelet coherency between cylinder pressure and liner acceleration signals at frequencies higher than 1 kHz. The coherent regions between cylinder pressure and sound pressure signals were mainly at frequencies higher than 1 kHz while advancing the fuel injection timing had shifted the coherency toward lower frequencies. In general, with advancing injection timing, the coherent regions between liner acceleration and sound pressure signals have appeared at broader time ranges, especially at frequencies between 100 and 500 Hz. Comparing the results of the wavelet coherency and coherency tests, we concluded that wavelet coherency is a more accurate and descriptive tool in evaluating the combustion-induced noise and vibration.

Effect of Injection Timing on Combustion Characteristics of a DI Diesel Engine Fuelled with Pistacia chinensis Bunge Seed Biodiesel

2012 ◽  
Vol 614-615 ◽  
pp. 337-342
Author(s):  
Li Luo ◽  
Bin Xu ◽  
Zhi Hao Ma ◽  
Jian Wu ◽  
Ming Li
Keyword(s):  
Combustion Temperature ◽  
Fuel Injection ◽  
Direct Injection ◽  
Combustion Characteristics ◽  
Injection Timing ◽  
Brake Specific Fuel Consumption ◽  
Cylinder Pressure ◽  
Combustion Duration ◽  
Di Diesel Engine ◽  
Maximum Combustion Temperature

In this study, the effect of injection timing on combustion characteristics of a direct injection, electronically controlled, high pressure, common rail, turbocharged and intercooled engine fuelled with different pistacia chinensis bunge seed biodiesel/diesel blends has been experimentally investigated. The results indicated that brake specific fuel consumption reduces with the increasing of fuel injection advance angle and enhances with the increasing of biodiesel content in the blends. The peak of cylinder pressure and maximum combustion temperature increase evidently with the increment of fuel injection advance angle. However, the combustion of biodiesel blends starts earlier than diesel at the same fuel injection advance angle. At both conditions, the combustion duration and the peak of heat release rate are insensitive to the changing of injection timing.

Experimental investigations on combustion of jatropha methyl ester in a turbocharged direct-injection diesel engine

2008 ◽  
Vol 222 (10) ◽  
pp. 1865-1877 ◽  
Author(s):  
K Anand ◽  
R P Sharma ◽  
P S Mehta
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Peak Pressure ◽  
Direct Injection ◽  
Pressure Rise ◽  
Experimental Investigations ◽  
Injection Timing ◽  
Gas Temperature

Suitability of vegetable oil as an alternative to diesel fuel in compression ignition engines has become attractive, and research in this area has gained momentum because of concerns on energy security, high oil prices, and increased emphasis on clean environment. The experimental work reported here has been carried out on a turbocharged direct-injection multicylinder truck diesel engine using diesel fuel and jatropha methyl ester (JME)-diesel blends. The results of the experimental investigation indicate that an increase in JME quantity in the blend slightly advances the dynamic fuel injection timing and lowers the ignition delay compared with the diesel fuel. A maximum rise in peak pressure limited to 6.5 per cent is observed for fuel blends up to 40 per cent JME for part-load (up to about 50 per cent load) operations. However, for a higher-JME blend, the peak pressures decrease at higher loads remained within 4.5 per cent. With increasing proportion of JME in the blend, the peak pressure occurrence slightly advances and the maximum rate of pressure rise, combustion duration, and exhaust gas temperature decrease by 9 per cent, 15 per cent and 17 per cent respectively. Although the changes in brake thermal efficiencies for 20 per cent and 40 per cent JME blends compared with diesel fuel remain insignificant, the 60 per cent JME blend showed about 2.7 per cent improvement in the brake thermal efficiency. In general, it is observed that the overall performance and combustion characteristics of the engine do not alter significantly for 20 per cent and 40 per cent JME blends but show an improvement over diesel performance when fuelled with 60 per cent JME blend.

A Numerical Study of NOx Reduction for a DI Diesel Engine With Complex Geometry

2004 ◽  
Vol 126 (1) ◽  
pp. 13-20 ◽  
Author(s):  
Renshan Liu ◽  
Chao Zhang
Keyword(s):  
Diesel Engine ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Complex Geometry ◽  
Numerical Study ◽  
Direct Injection ◽  
Nox Reduction ◽  
Geometrical Parameters ◽  
Injection Timing ◽  
Di Diesel Engine

A numerical study of NOx reduction for a Direct Injection (DI) Diesel engine with complex geometry, which includes intake/exhaust ports and moving valves, was carried out using the commercial computational fluid dynamics software KIVA-3v. The numerical simulations were conducted to investigate the effects of engine operating and geometrical parameters, including fuel injection timing, fuel injection duration, and piston bowl depth, on the NOx formation and the thermal efficiency of the DI Diesel engine. The tradeoff relationships between the reduction in NOx and the decrease in thermal efficiency were established.

Factors Affecting Performance of Dual Fuel Compression Ignition Engines

2013 ◽  
Vol 388 ◽  
pp. 217-222
Author(s):  
Mohamed Mustafa Ali ◽  
Sabir Mohamed Salih
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection System ◽  
Dual Fuel ◽  
Injection Timing ◽  
Compression Ignition ◽  
Factors Affecting

Compression Ignition Diesel Engine use Diesel as conventional fuel. This has proven to be the most economical source of prime mover in medium and heavy duty loads for both stationary and mobile applications. Performance enhancements have been implemented to optimize fuel consumption and increase thermal efficiency as well as lowering exhaust emissions on these engines. Recently dual fueling of Diesel engines has been found one of the means to achieve these goals. Different types of fuels are tried to displace some of the diesel fuel consumption. This study is made to identify the most favorable conditions for dual fuel mode of operation using Diesel as main fuel and Gasoline as a combustion improver. A single cylinder naturally aspirated air cooled 0.4 liter direct injection diesel engine is used. Diesel is injected by the normal fuel injection system, while Gasoline is carbureted with air using a simple single jet carburetor mounted at the air intake. The engine has been operated at constant speed of 3000 rpm and the load was varied. Different Gasoline to air mixture strengths investigated, and diesel injection timing is also varied. The optimum setting of the engine has been defined which increased the thermal efficiency, reduced the NOx % and HC%.

Effect of Injection Parameters and Strategy on the Noise From a Single Cylinder Direct Injection Diesel Engine

2011 ◽  
Author(s):  
Sukhbir Singh Khaira ◽  
Amandeep Singh ◽  
Marcis Jansons
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Injection Pressure ◽  
Combustion Noise ◽  
Injection Timing ◽  
Cylinder Pressure ◽  
Frequency Spectra ◽  
Single Cylinder ◽  
Direct Injection Diesel Engine ◽  
Injection Parameters

Acoustic noise emitted by a diesel engine generally exceeds that produced by its spark-ignited equivalent and may hinder the acceptance of this more efficient engine type in the passenger car market (1). This work characterizes the combustion noise from a single-cylinder direct-injection diesel engine and examines the degree to which it may be minimized by optimal choice of injection parameters. The relative contribution of motoring, combustion and resonance components to overall engine noise are determined by decomposition of in-cylinder pressure traces over a range of load, injection pressure and start of injection. The frequency spectra of microphone signals recorded external to the engine are correlated with those of in-cylinder pressure traces. Short Time Fourier Transformation (STFT) is applied to cylinder pressure traces to reveal the occurrence of motoring, combustion noise and resonance in the frequency domain over the course of the engine cycle. Loudness is found to increase with enhanced resonance, in proportion to the rate of cylinder pressure rise and under conditions of high injection pressure, load and advanced injection timing.

Effect of Injection System Parameters on Performance and Emission Characteristics of a Small Single Cylinder Diesel Engine

2021 ◽  
Vol 18 (2) ◽  
Author(s):  
D.K. Dond ◽  
N.P. Gulhane
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Direct Injection ◽  
Common Rail ◽  
Injection System ◽  
Injection Timing ◽  
Emission Characteristics ◽  
Performance And Emission ◽  
System Parameters ◽  
Main Injection

Limited fossil fuel reservoir capacity and pollution caused by them is the big problem in front of researchers. In the present paper, an attempt was made to find a solution to the same. The conventional fuel injection system was retrofitted with a simple version of the common rail direct injection system for the small diesel engine. Further, the effect of injection system parameters was observed on the performance and emission characteristics of the retrofitted common rail direct injection diesel engine. The parameters such as injection pressure, the start of pilot injection timing, the start of main injection timing and quantity of percentage fuel injection during the pilot and main injection period were considered for experimental investigation. It was observed that all the evaluated parameters were found vital for improving the engine’s performance and emission characteristics. The retrofitted common rail direct injection system shows an average 7% rise in brake thermal efficiency with economic, specific fuel consumption. At the same time, much more reduction in hydrocarbon, carbon monoxide and smoke opacity with a penalty of a slight increase in nitrogen oxides.

An Experimental Investigation of Hydrogen Fumigation in a Small Direct-Injection Diesel Engine During Part-Load Operation

2011 ◽  
Author(s):  
William E. Marin ◽  
Daniel P. Wiese ◽  
Paul A. Erickson
Keyword(s):  
Diesel Engine ◽  
Flow Rate ◽  
Thermal Efficiency ◽  
Direct Injection ◽  
Low Energy ◽  
Injection Timing ◽  
Effective Pressure ◽  
Cylinder Pressure ◽  
Indicated Mean Effective Pressure ◽  
Hydrogen Enrichment

Hydrogen enrichment may offer enhanced performance of internal combustion engines. Hydrogen’s high specific energy, wide flammability limits, and high flame speed are all desirable traits that can potentially enhance combustion. However, hydrogen’s low energy density and its need to be produced from another energy source pose significant challenges for implementation. Hydrogen enrichment involves co-firing of hydrogen and another primary fuel. The hydrogen can be aspirated through the intake manifold via fumigation or injected at the port or cylinder with the primary fuel. The effect of hydrogen fumigation in diesel engines has been studied to some degree but is not fully understood. In this research, a single-cylinder four-stroke direct-injection diesel engine was modified for hydrogen fumigation and was instrumented to monitor combustion related performance parameters. This engine is representative of low-cost systems that are widely used in developing nations for agricultural and other low power applications. A factorial design of experiments was implemented to study the effects and interactions of hydrogen fumigation flow rate, injection timing, and diesel fuel flow rate on part-load engine performance. At relatively low energy fractions, hydrogen was found to have statistically insignificant effects on brake torque and indicated mean effective pressure, leading to modest decreases in brake thermal efficiency. Exhaust gas temperature increased with hydrogen enrichment. The coefficient of variance of indicated mean effective pressure decreased with hydrogen enrichment, and visible changes to the in-cylinder pressure trace were observed, particularly when injection timing was retarded. The results of this investigation show that for this specific configuration, hydrogen enrichment is not beneficial to the combustion process. The marginal improvements in coefficient of variance and changes of in-cylinder pressure cannot justify the decrease in thermal efficiency of the engine.

Sign in / Sign up

Export Citation Format

Share Document