Surface Texture and Machining Conditions. Part 1: Model Building Logic in View of Process Control

1983 ◽  
Vol 105 (4) ◽  
pp. 259-263 ◽  
Author(s):  
A. Villa ◽  
S. Rossetto ◽  
R. Levi
Keyword(s):  
Process Control ◽  
Surface Texture ◽  
Model Building ◽  
Surface Profile ◽  
Cutting Parameters ◽  
Tool Geometry ◽  
Machining Processes ◽  
Tool Marks ◽  
Machining Conditions ◽  
Cutting Processes

Surface texture generation in machining processes is examined in view of establishing a model building procedure capable of linking surface finish parameters to machining conditions. In the first part of the paper, with reference to cutting processes with defined tool geometry, a model capable of describing a surface profile as an ordered sequence of tool marks is developed. The use of such a model for process control is also discussed. In the second part, the identification procedure of a model describing profile generation in face milling versus cutting parameters is presented.

Optimisation of the Bauer Equation Using the Least Squares Method for Thermoplastics Turning

2018 ◽  
Vol 8 (1) ◽  
pp. 21-36
Author(s):  
János Farkas ◽  
Etele Csanády ◽  
Levente Csóka
Keyword(s):  
Surface Roughness ◽  
Least Squares Method ◽  
Composite Ceramic ◽  
Cutting Parameters ◽  
Machining Process ◽  
Tool Geometry ◽  
Machining Processes ◽  
Simple Formulation ◽  
Plastic Composite ◽  
Cutting Speeds

A number of equations are available for predicting the output of machining processes. These equations are most commonly used for the prediction of surface roughness after tooling. Surface roughness can be influenced by many factors, including cutting parameters, tool geometry and environmental factors such as the coolant used. It is difficult to create a universally applicable equation for all machining because of the variations in different materials' behaviours (e.g. metal, wood, plastic, composite, ceramic). There are also many differences between the various types of machining process such as the machining tools, rotational or translational movements, cutting speeds, cutting methods, etc. The large number of parameters required would make such an equation unusable, and difficult to apply quickly. The goal is thus to create a simple formulation with three or four inputs to predict the final surface roughness of the machined part within adequate tolerances. The two main equations used for this purpose are the Bauer and Brammertz formulas, both of which need to be optimised for a given material. In this paper, the turning of thermoplastics was investigated, with the aim of tuning the Bauer formula for use with thermoplastics. Eleven different plastics were used to develop a material-dependent surface roughness equation. Only new tooling inserts were used to eliminate the effects of tool wear.

Machining Conditions Effect to Machining Temperature and Forces in Orthogonal Machining of Bone

2013 ◽  
Vol 658 ◽  
pp. 223-226 ◽  
Author(s):  
Denni Kurniawan ◽  
N. Jiawkok ◽  
M.Y. Noordin
Keyword(s):  
Analytical Study ◽  
Cutting Speed ◽  
Tool Geometry ◽  
Depth Of Cut ◽  
Machining Processes ◽  
Allowable Limit ◽  
Machining Conditions ◽  
Orthogonal Machining ◽  
Dental Implantation ◽  
Cutting Direction

Bone machining processes are often performed in orthopaedic surgery and dental implantation, yet its analytical study is lacking. Towards contributing analysis on bone machining, this study reviews available references on orthogonal machining of bones. Considering the allowable limit in temperature and duration during bone machining to avoid thermal necrosis, machining temperature and forces are the machining responses of interest. Machining conditions (cutting speed, depth of cut, cooling method, tool geometry, and cutting direction) are analyzed in term of their effect to those machining responses.

Influence of Cutting Parameters and Tool Geometry on Cutting Forces and Damage on 2D and 3D Carbon/Epoxy Composites in Drilling

2014 ◽  
Vol 611-612 ◽  
pp. 1217-1225 ◽  
Author(s):  
Yosra Turki ◽  
Malek Habak ◽  
Raphael Velasco ◽  
Pascal Vantomme ◽  
Kamel Khellil
Keyword(s):  
Cutting Forces ◽  
Thrust Force ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Epoxy Composites ◽  
Tool Geometry ◽  
Machining Conditions ◽  
Force Moment ◽  
2D And 3D ◽  
The Relationship

The evolution of carbon/epoxy composites use in aeronautics requires a better comprehension of the machining conditions influence on these materials. This study aim is to establish, based on the experimentation, the relationship between machining conditions and the behavior of drilled 2D and 3D carbon/epoxy composites. Two drill geometries, seam introducing and a range of cutting speed and feed have been tested. The effect of each parameter has been assessed in terms of thrust force, moment (recorded during machining) and defects (performed by macroscopic analyses and quantified using delamination factor Fd). Experimental results have shown significant influences of feed and drill geometry on delamination reduction. The use of a spur drill and a low feed generates minor defects and produces the best results. Furthermore, stitching helps reduce damage inside the hole.

scholarly journals Modeling of Cutting Parameters and Tool Geometry for Multi-Criteria Optimization of Surface Roughness and Vibration via Response Surface Methodology in Turning of AISI 5140 Steel

Materials ◽  
2020 ◽  
Vol 13 (19) ◽  
pp. 4242 ◽  
Author(s):  
Mustafa Kuntoğlu ◽  
Abdullah Aslan ◽  
Danil Yurievich Pimenov ◽  
Khaled Giasin ◽  
Tadeusz Mikolajczyk ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Prediction Models ◽  
High Reliability ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Cutting Edge ◽  
Tool Geometry ◽  
Machining Processes

AISI 5140 is a steel alloy used for manufacturing parts of medium speed and medium load such as gears and shafts mainly used in automotive applications. Parts made from AISI 5140 steel require machining processes such as turning and milling to achieve the final part shape. Limited research has been reported on the machining vibration and surface roughness during turning of AISI 5140 in the open literature. Therefore, the main aim of this paper is to conduct a systematic study to determine the optimum cutting conditions, analysis of vibration and surface roughness under different cutting speeds, feed rates and cutting edge angles using response surface methodology (RSM). Prediction models were developed and optimum turning parameters were obtained for averaged surface roughness (Ra) and three components of vibration (axial, radial and tangential) using RSM. The results demonstrated that the feed rate was the most affecting parameter in increasing the surface roughness (69.4%) and axial vibration (65.8%) while cutting edge angle and cutting speed were dominant on radial vibration (75.5%) and tangential vibration (64.7%), respectively. In order to obtain minimum vibration for all components and surface roughness, the optimum parameters were determined as Vc = 190 m/min, f = 0.06 mm/rev, κ = 60° with high reliability (composite desirability = 90.5%). A good agreement between predicted and measured values was obtained with the developed model to predict surface roughness and vibration during turning of AISI 5140 within a 10% error range.

Studying The Effect of a New Mixed Cutting Fluid on Surface Roughness

2020 ◽  
Vol 38 (11A) ◽  
pp. 1593-1601
Author(s):  
Mohammed H. Shaker ◽  
Salah K. Jawad ◽  
Maan A. Tawfiq
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Cutting Parameters ◽  
Machining Process ◽  
Cutting Fluid ◽  
Depth Of Cut ◽  
Cutting Fluids ◽  
Machining Processes ◽  
Dry Cutting ◽  
Cutting Speeds

This research studied the influence of cutting fluids and cutting parameters on the surface roughness for stainless steel worked by turning machine in dry and wet cutting cases. The work was done with different cutting speeds, and feed rates with a fixed depth of cutting. During the machining process, heat was generated and effects of higher surface roughness of work material. In this study, the effects of some cutting fluids, and dry cutting on surface roughness have been examined in turning of AISI316 stainless steel material. Sodium Lauryl Ether Sulfate (SLES) instead of other soluble oils has been used and compared to dry machining processes. Experiments have been performed at four cutting speeds (60, 95, 155, 240) m/min, feed rates (0.065, 0.08, 0.096, 0.114) mm/rev. and constant depth of cut (0.5) mm. The amount of decrease in Ra after the used suggested mixture arrived at (0.21µm), while Ra exceeded (1µm) in case of soluble oils This means the suggested mixture gave the best results of lubricating properties than other cases.

scholarly journals Temperature monitoring in the subsurface during single lip deep hole drilling

2020 ◽  
Vol 87 (12) ◽  
pp. 757-767
Author(s):  
Robert Wegert ◽  
Vinzenz Guski ◽  
Hans-Christian Möhring ◽  
Siegfried Schmauder
Keyword(s):  
Cutting Parameters ◽  
Drill Hole ◽  
Machining Process ◽  
Hole Drilling ◽  
Drilling Process ◽  
Deep Hole ◽  
Machining Processes ◽  
Deep Hole Drilling ◽  
Feed Force ◽  
Cutting Zone

AbstractThe surface quality and the subsurface properties such as hardness, residual stresses and grain size of a drill hole are dependent on the cutting parameters of the single lip deep hole drilling process and therefore on the thermomechanical as-is state in the cutting zone and in the contact zone between the guide pads and the drill hole surface. In this contribution, the main objectives are the in-process measurement of the thermal as-is state in the subsurface of a drilling hole by means of thermocouples as well as the feed force and drilling torque evaluation. FE simulation results to verify the investigations and to predict the thermomechanical conditions in the cutting zone are presented as well. The work is part of an interdisciplinary research project in the framework of the priority program “Surface Conditioning in Machining Processes” (SPP 2086) of the German Research Foundation (DFG).This contribution provides an overview of the effects of cutting parameters, cooling lubrication and including wear on the thermal conditions in the subsurface and mechanical loads during this machining process. At first, a test set up for the in-process temperature measurement will be presented with the execution as well as the analysis of the resulting temperature, feed force and drilling torque during drilling a 42CrMo4 steel. Furthermore, the results of process simulations and the validation of this applied FE approach with measured quantities are presented.

scholarly journals FEM and Analytical Modeling of the Incipient Chip Formation for the Generation of Micro-Features

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3789
Author(s):  
Michele Lanzetta ◽  
Marco Picchi Picchi Scardaoni ◽  
Armin Gharibi ◽  
Claudia Vivaldi
Keyword(s):  
Material Properties ◽  
Analytical Modeling ◽  
Cutting Tool ◽  
Sustainable Manufacturing ◽  
Cutting Parameters ◽  
Micro Machining ◽  
Machining Processes ◽  
Steel Alloys ◽  
Diamond Blade ◽  
Micro Features

This paper explores the modeling of incipient cutting by Abaqus, LS-Dyna, and Ansys Finite Element Methods (FEMs), by comparing also experimentally the results on different material classes, including common aluminum and steel alloys and an acetal polymer. The target application is the sustainable manufacturing of gecko adhesives by micromachining a durable mold for injection molding. The challenges posed by the mold shape include undercuts and sharp tips, which can be machined by a special diamond blade, which enters the material, forms a chip, and exits. An analytical model to predict the shape of the incipient chip and of the formed grove as a function of the material properties and of the cutting parameters is provided. The main scientific merit of the current work is to approach theoretically, numerically, and experimentally the very early phase of the cutting tool penetration for new sustainable machining and micro-machining processes.

scholarly journals Effect of Cutting Parameters and Tool Geometry on the Performance Analysis of One-Shot Drilling Process of AA2024-T3

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 854
Author(s):  
Muhammad Aamir ◽  
Khaled Giasin ◽  
Majid Tolouei-Rad ◽  
Israr Ud Din ◽  
Muhammad Imran Hanif ◽  
...  
Keyword(s):  
Feed Rate ◽  
Surface Defects ◽  
Thrust Force ◽  
Cutting Tools ◽  
Chip Thickness ◽  
Cutting Parameters ◽  
Spindle Speed ◽  
Machining Process ◽  
Tool Geometry ◽  
Drilling Process

Drilling is an important machining process in various manufacturing industries. High-quality holes are possible with the proper selection of tools and cutting parameters. This study investigates the effect of spindle speed, feed rate, and drill diameter on the generated thrust force, the formation of chips, post-machining tool condition, and hole quality. The hole surface defects and the top and bottom edge conditions were also investigated using scan electron microscopy. The drilling tests were carried out on AA2024-T3 alloy under a dry drilling environment using 6 and 10 mm uncoated carbide tools. Analysis of Variance was employed to further evaluate the influence of the input parameters on the analysed outputs. The results show that the thrust force was highly influenced by feed rate and drill size. The high spindle speed resulted in higher surface roughness, while the increase in the feed rate produced more burrs around the edges of the holes. Additionally, the burrs formed at the exit side of holes were larger than those formed at the entry side. The high drill size resulted in greater chip thickness and an increased built-up edge on the cutting tools.

Experimental investigation of the influence of cutting parameters on surface quality and on the special characteristics of micro-milled surfaces of hardened steels

2021 ◽  
pp. 095440622110130
Author(s):  
Barnabás Zoltán Balázs ◽  
Márton Takács
Keyword(s):  
Surface Quality ◽  
Surface Profile ◽  
Cutting Parameters ◽  
Relevant Information ◽  
Milling Process ◽  
Micro Milling ◽  
Machined Surface ◽  
Analysis Of Dynamics ◽  
Five Axis ◽  
Coated Carbide

Micro-milling is one of the most essential technologies to produce micro components, but due to the size effect, it has many special characteristics and challenges. The process can be characterised by strong vibrations, relatively large run-out and tool deformation, which directly affects the quality of the machined surface. This paper deals with a detailed investigation of the influence of cutting parameters on surface roughness and on the special characteristics of micro-milled surfaces. Several systematic series of experiments were carried out and analysed in detail. A five-axis micromachining centre and a two fluted, coated carbide micro-milling tool with a diameter of 500 µm were used for the tests. The experiments were conducted on AISI H13 hot-work tool steel and Böhler M303 martensitic corrosion resistance steel with a hardness of 50 HRC in order to gain relevant information of machining characteristics of potential materials of micro-injection moulding tools. The effect of the cutting parameters on the surface quality and on the ratio of Rz/ Ra was investigated in a comprehensive cutting parameter range. ANOVA was used for the statistical evaluation. A novel method is presented, which allows a detailed analysis of the surface profile and repetitions, and identify the frequencies that create the characteristic profile of the surface. The procedure establishes a connection between the frequencies obtained during the analysis of dynamics (forces, vibrations) of the micro-milling process and the characterising repetitions and frequencies of the surface.

Sign in / Sign up

Export Citation Format

Share Document