End-Wall and Profile Losses in a Low-Speed Axial Flow Compressor Rotor

1986 ◽  
Vol 108 (1) ◽  
pp. 22-31 ◽  
Author(s):  
B. Lakshminarayana ◽  
N. Sitaram ◽  
J. Zhang
Keyword(s):  
Axial Flow ◽  
Pressure Rise ◽  
Tip Clearance ◽  
Blade Loading ◽  
Pressure Losses ◽  
Axial Flow Compressor ◽  
Compressor Rotor ◽  
Profile Losses ◽  
Flow Compressor ◽  
End Wall

The blade-to-blade variation of relative stagnation pressure losses in the tip region inside the rotor of a single-stage, axial-flow compressor is presented and interpreted in this paper. The losses are measured at two flow coefficients (one at the design point and the other at the near peak pressure rise point) to discern the effect of blade loading on the end-wall losses. The tip clearance losses are found to increase with an increase in the pressure rise coefficient. The losses away from the tip region and near the hub regions are measured downstream. The losses are integrated and interpreted in this paper.

scholarly journals Effect of Circumferential Single Casing Groove Location on the Flow Stability under Tip-Clearance Effect in a Transonic Axial Flow Compressor Rotor

Energies ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 6143
Author(s):  
Xiaoxiong Wu ◽  
Bo Liu ◽  
Botao Zhang ◽  
Xiaochen Mao
Keyword(s):  
Control Mechanism ◽  
Incidence Angle ◽  
Axial Flow ◽  
Flow Stability ◽  
Tip Clearance ◽  
Tip Leakage Flow ◽  
Flow Angle ◽  
Axial Flow Compressor ◽  
Compressor Rotor ◽  
Flow Compressor

Numerical simulations have been performed to study the effect of the circumferential single-grooved casing treatment (CT) at multiple locations on the tip-flow stability and the corresponding control mechanism at three tip-clearance-size (TCS) schemes in a transonic axial flow compressor rotor. The results show that the CT is more efficient when its groove is located from 10% to 40% tip axial chord, and G2 (located at near 20% tip axial chord) is the best CT scheme in terms of stall-margin improvement for the three TCS schemes. For effective CTs, the tip-leakage-flow (TLF) intensity, entropy generation and tip-flow blockage are reduced, which makes the interface between TLF and mainstream move downstream. A quantitative analysis of the relative inlet flow angle indicates that the reduction of flow incidence angle is not necessary to improve the flow stability for this transonic rotor. The control mechanism may be different for different TCS schemes due to the distinction of the stall inception process. For a better application of CT, the blade tip profile should be further modified by using an optimization method to adjust the shock position and strength during the design of a more efficient CT.

Numerical Investigations of the Coupled Flow Through a Subsonic Compressor Rotor and Axial Skewed Slot

2008 ◽  
Vol 131 (1) ◽  
Author(s):  
Xingen Lu ◽  
Wuli Chu ◽  
Junqiang Zhu ◽  
Yangfeng Zhang
Keyword(s):  
Axial Flow ◽  
Tip Clearance ◽  
Stall Margin ◽  
Tip Clearance Flow ◽  
Casing Treatment ◽  
Axial Flow Compressor ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Flow Through ◽  
Flow Compressor

In order to advance the understanding of the fundamental mechanisms of axial skewed slot casing treatment and their effects on the subsonic axial-flow compressor flow field, the coupled unsteady flow through a subsonic compressor rotor and the axial skewed slot was simulated with a state-of-the-art multiblock flow solver. The computational results were first compared with available measured data, that showed the numerical procedure calculates the overall effect of the axial skewed slot correctly. Then, the numerically obtained flow fields were interrogated to identify the physical mechanism responsible for improvement in stall margin of a modern subsonic axial-flow compressor rotor due to the discrete skewed slots. It was found that the axial skewed slot casing treatment can increase the stall margin of subsonic compressor by repositioning of the tip clearance flow trajectory further toward the trailing of the blade passage and retarding the movement of the incoming∕tip clearance flow interface toward the rotor leading edge plane.

1118 Effect of Tip Clearance on Rotating Stall Inception in an Axial Flow Compressor Rotor

2009 ◽  
Vol 2009 (0) ◽  
pp. 377-378 ◽  
Author(s):  
Hiroaki KIKUTA ◽  
Masato FURUKAWA ◽  
Satoshi GUNJISHIMA ◽  
Kenichiro IWAKIRI ◽  
Takuro KAMEDA
Keyword(s):  
Axial Flow ◽  
Rotating Stall ◽  
Tip Clearance ◽  
Stall Inception ◽  
Axial Flow Compressor ◽  
Compressor Rotor ◽  
Flow Compressor

2415 Effect of Tip Clearance on Structure of Rotating Stall Cell in an Axial Flow Compressor Rotor

2006 ◽  
Vol 2006.2 (0) ◽  
pp. 149-150
Author(s):  
Sho BONKOHARA ◽  
Ken-ichiro IWAKIRI ◽  
Ryusuke OHTAGURO ◽  
Yasuhiro SHIBAMOTO ◽  
Masato FURUKAWA
Keyword(s):  
Axial Flow ◽  
Rotating Stall ◽  
Tip Clearance ◽  
Axial Flow Compressor ◽  
Compressor Rotor ◽  
Flow Compressor

Experimental Investigation of Stepped Tip Gap Effects on the Performance of a Transonic Axial-Flow Compressor Rotor

1998 ◽  
Vol 120 (3) ◽  
pp. 477-486 ◽  
Author(s):  
D. W. Thompson ◽  
P. I. King ◽  
D. C. Rabe
Keyword(s):  
Mass Flow ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Axial Flow Compressor ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Percent Improvement ◽  
Flow Compressor

The effects of stepped-tip gaps and clearance levels on the performance of a transonic axial-flow compressor rotor were experimentally determined. A two-stage compressor with no inlet guide vanes was tested in a modern transonic compressor research facility. The first-stage rotor was unswept and was tested for an optimum tip clearance with variations in stepped gaps machined into the casing near the aft tip region of the rotor. Nine causing geometries were investigated consisting of three step profiles at each of three clearance levels. For small and intermediate clearances, stepped tip gaps were found to improve pressure ratio, efficiency, and flow range for most operating conditions. At 100 percent design rotor speed, stepped tip gaps produced a doubling of mass flow range with as much as a 2.0 percent increase in mass flow and a 1.5 percent improvement in efficiency. This study provides guidelines for engineers to improve compressor performance for an existing design by applying an optimum casing profile.

Experimental Investigation of Stepped Tip Gap Effects on the Performance of a Transonic Axial-Flow Compressor Rotor

1997 ◽  
Author(s):  
Donald W. Thompson ◽  
Paul I. King ◽  
Douglas C. Rabe
Keyword(s):  
Mass Flow ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Axial Flow Compressor ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Compressor Performance ◽  
Flow Compressor

The effects of stepped tip gaps and clearance levels on the performance of a transonic axial-flow compressor rotor were experimentally determined. A two-stage compressor with no inlet guide vanes was tested in a modern transonic compressor research facility. The first-stage rotor was unswept and was tested for an optimum tip clearance with variations in stepped gaps machined into the casing near the aft tip region of the rotor. Nine casing geometries were investigated consisting of three step profiles at each of three clearance levels. For small and intermediate clearances, stepped tip gaps were found to improve pressure ratio, efficiency, and flow range for most operating conditions. At 100% design rotor speed, stepped tip gaps produced a doubling of mass flow range with as much as a 2.0% increase in mass flow and a 1.5% improvement in efficiency. This study provides guidelines for engineers to improve compressor performance for an existing design by applying an optimum casing profile.

Flow Fields in an Axial Flow Compressor During Four-Quadrant Operation

2013 ◽  
Author(s):  
Andrew Gill ◽  
Theodor W. von Backström ◽  
Thomas M. Harms ◽  
Dwain Dunn
Keyword(s):  
Flow Direction ◽  
Tangential Velocity ◽  
Axial Compressor ◽  
Axial Flow ◽  
Pressure Rise ◽  
Flow Fields ◽  
Time Dependent ◽  
Axial Flow Compressor ◽  
Compressor Rotor ◽  
Flow Compressor

It has been shown in previous investigations that when all combinations of both positive and negative direction of rotation and flow direction are allowed in operating a multistage axial flow compressor, the operating point may be in any of the four quadrants of the pressure rise versus flow characteristic. The present paper is the first discussion of the flow field of all possible modes of operation of an axial flow compressor. During the present study interstage time dependent hot film velocity measurements and five hole pneumatic probe measurements were combined with steady and time dependent CFD solutions to investigate the flow fields in the three-stage axial compressor. Results are presented in terms of mean-line velocity triangles, mean stream surface plots, mid-span radial velocity contours right through the compressor, rotor-downstream radial distributions of axial and tangential velocity, stator-downstream axial velocity contours and mid-span entropy contours through the compressor. Main flow features are pointed out and discussed. The study was instigated in an effort to understand possible accident scenarios in a three-shaft closed cycle nuclear powered helium gas turbine.

Combined Effects of Forward Sweep and Tip Clearance on the Performance of Axial Flow Compressor Stage

2009 ◽  
Author(s):  
P. V. Ramakrishna ◽  
M. Govardhan
Keyword(s):  
Total Pressure ◽  
Axial Compressor ◽  
Axial Flow ◽  
Pressure Rise ◽  
Tip Clearance ◽  
Numerical Work ◽  
Low Speed ◽  
Operating Range ◽  
Axial Flow Compressor ◽  
Flow Compressor

There are a number of performance indices for a turbomachine on the basis of which its strength is evaluated. In the case of axial compressors, pressure ratio, efficiency and stall margin are few such indices which are of major concern in the design phase as well as in the evaluation of performance of the machine. In the process of improving the blade design, 3D blade stacking, where the aerofoil sections constituting the blade are moved in relation to the flow. Tilting the blade sections to the flow direction (blade sweep) would increase the operating range of an axial compressor due to modifications in the pressure and velocity fields on the suction surface. On the other hand, blade tip gap, though finite, has great influence on the performance of a turbomachine. The present work investigates the combined effect of these two factors on various flow characteristics in a low speed axial flow compressor. The objective of the present paper is thereby confined to study the collective effects of sweep and tip clearance without attempting to suggest an outright new design. In the present numerical work, the performance of Tip Chordline Sweeping (TCS) and Axial Sweeping (AXS) of low speed axial compressor rotor blades are studied. For this, 15 computational domains were modeled for five rotor sweep configurations and three different clearance levels for each rotor. Through the results, 20°AXS rotor is found to be distinctive among all the rotors with highest pressure rise, higher operating range and less tip clearance loss characteristics. TCS rotors produced improved total pressure rise at the low flow coefficients when the tip gap is increased. Hence there is a chance that an “optimum” tip gap exists for the TCS rotors in terms of total pressure coefficient and operating range, while AXS rotors are at their best with the minimum possible clearance.

scholarly journals Study of Sweep and Induced Dihedral Effects in Subsonic Axial Flow Compressor Passages—Part II: Detailed Study of the Effects on Tip Leakage Phenomena

2010 ◽  
Vol 2010 ◽  
pp. 1-13 ◽  
Author(s):  
P. V. Ramakrishna ◽  
M. Govardhan
Keyword(s):  
Axial Compressor ◽  
Axial Flow ◽  
High Sensitivity ◽  
Tip Clearance ◽  
Flow Coefficient ◽  
Tip Vortex ◽  
Pressure Losses ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Flow Compressor

This article presents the detailed study of rotor tip leakage related phenomena in a low speed axial compressor rotor passages for three sweep configurations [Unswept (UNS), Tip Chordline Swept (TCS) and Axially Swept (AXS)]. Fifteen domains are numerically studied with 5 sweep configurations (0°, 20°TCS, 30°TCS, 20°AXS, and 30°AXS) and for 3 tip clearances (0.0%, 0.7% and 2.7% of the blade chord). Results were well validated with experimental data. Observations near the tip reveal that UNS rotor shows high sensitivity than the swept rotors in the blade pressure distribution with change in tip clearance. AXS rotor has high loading capability and less tip clearance effect on blade loading at the near stall mass flow. Downstream shift of the vortex rollup along the chord is observed with increased flow coefficient and increment in the tip gap height. In particular, the effect of flow coefficient is more predominant on this effect. Tip vortex-related flow blockage is less with the swept rotors. Among the rotors, the AXS rotor is found to incur low total pressure losses attributable to tip leakage. Effect of incidence is observed on the flow leakage direction.

Sign in / Sign up

Export Citation Format

Share Document