Pressure-Plus-Moment Limit-Load Analysis for a Cylindrical Shell Nozzle

1987 ◽  
Vol 109 (3) ◽  
pp. 297-301 ◽  
Author(s):  
C. J. Tabone ◽  
R. H. Mallett
Keyword(s):  
Cylindrical Shell ◽  
Three Dimensional ◽  
Limit Load ◽  
Element Model ◽  
Combined Loading ◽  
Inelastic Behavior ◽  
Limit Loads ◽  
Out Of Plane ◽  
Load Analysis ◽  
The Moment

A finite element model of a nozzle in a cylindrical shell is analyzed for three cases; pressure, out-of-plane moment and combined pressure plus out-of-plane moment. The model uses three-dimensional finite elements and the analysis considers inelastic behavior at small displacements. Load versus displacement behavior is given for the three cases. Estimates of limit loads are obtained based upon extrapolation of load versus inverse displacement data curves. An interaction expression is used to show the effect of the combined loading for a case in which an internal pressure reduces the moment capability of the nozzle by 35 percent.

Limit Load Analysis of Crack Contained Thick Walled Cylinders

2010 ◽  
Author(s):  
Saeid Hadidi-Moud ◽  
David John Smith
Keyword(s):  
Plastic Deformation ◽  
Limit State ◽  
Limit Load ◽  
Combined Loading ◽  
Finite Element Analyses ◽  
Limit Loads ◽  
Integrity Assessment ◽  
Crack Configuration ◽  
Load Analysis

Reliable limit load estimations for thick walled pressurized cylinders containing defects are required for the assessment of integrity of structures that experience significant plastic deformation prior to failure. Analytical and finite element analyses of limit load in thick walled cylinders containing defects are presented in this paper. FE analyses were conducted to obtain estimates of the limit state of loading for a range of combined loading schemes and loading sequences for open-end and closed-end cylinder. Part through shallow and deep hoop cracks in the cylinder for uniform radial, uniform axial and combined loading were examined. The results suggest that adjustments to the estimates of limit loads obtained from conventional methods reported in literature are needed in order to reflect the role of material response, crack configuration and boundary conditions on the limit loads of defected thick walled pipes and cylinders. These findings are very important and should be noted carefully, especially in the context of treatment of hoop and axial residual stresses in the integrity assessment of pipelines containing part through cracks.

Limit Load Analysis of Cracked Components Using the Reference Volume Method

2006 ◽  
Vol 129 (3) ◽  
pp. 391-399 ◽  
Author(s):  
R. Adibi-Asl ◽  
R. Seshadri
Keyword(s):  
Elastic Modulus ◽  
Three Dimensional ◽  
Local Limit ◽  
Limit Load ◽  
Multiple Cracks ◽  
Element Analysis ◽  
Limit Loads ◽  
Integrity Assessment ◽  
Reference Volume ◽  
Volume Method

Cracks and flaws occur in mechanical components and structures, and can lead to catastrophic failures. Therefore, integrity assessment of components with defects is carried out. This paper describes the Elastic Modulus Adjustment Procedures (EMAP) employed herein to determine the limit load of components with cracks or crack-like flaw. On the basis of linear elastic Finite Element Analysis (FEA), by specifying spatial variations in the elastic modulus, numerous sets of statically admissible and kinematically admissible distributions can be generated, to obtain lower and upper bounds limit loads. Due to the expected local plastic collapse, the reference volume concept is applied to identify the kinematically active and dead zones in the component. The Reference Volume Method is shown to yield a more accurate prediction of local limit loads. The limit load values are then compared with results obtained from inelastic FEA. The procedures are applied to a practical component with crack in order to verify their effectiveness in analyzing crack geometries. The analysis is then directed to geometries containing multiple cracks and three-dimensional defect in pressurized components.

Lateral Buckling of Cantilevered Circular Arches Under Various End Moments

2020 ◽  
Vol 20 (07) ◽  
pp. 2071005
Author(s):  
Y. B. Yang ◽  
Y. Z. Liu
Keyword(s):  
Differential Equations ◽  
Boundary Conditions ◽  
Analytical Solutions ◽  
Analytical Approach ◽  
Three Dimensional ◽  
Curved Beams ◽  
Lateral Buckling ◽  
Circular Arch ◽  
Out Of Plane ◽  
The Moment

Lateral buckling of cantilevered circular arches under various end moments is studied using an analytical approach. Three types of conservative moments are considered, i.e. the quasi-tangential moments of the 1st and 2nd kinds, and the semi-tangential moment. The induced moments associated with each of the moment mechanisms undergoing three-dimensional rotations are included in the Newman boundary conditions. Using the differential equations available for the out-of-plane buckling of curved beams, the analytical solutions are derived for a cantilevered circular arch, which can be used as the benchmarks for calibration of other methods of analysis.

Study of arching behaviour and strength of concrete masonry infills under out-of-plane loading

2019 ◽  
Vol 46 (10) ◽  
pp. 896-908 ◽  
Author(s):  
Ehsan Nasiri ◽  
Yi Liu
Keyword(s):  
Numerical Study ◽  
Three Dimensional ◽  
Element Model ◽  
Contributing Factors ◽  
Concrete Frames ◽  
Masonry Infills ◽  
Concrete Masonry ◽  
Wide Range ◽  
Out Of Plane ◽  
Three Dimensional Finite Element

A numerical study using a three-dimensional finite element model was conducted to investigate the arching behaviour and strength of concrete masonry infills bounded by reinforced concrete frames subjected to out-of-plane loading. Physical specimens were concurrently tested to provide results for validation of the model as well as evidence of directional characteristics of arching behaviour of masonry infills. A subsequent parametric study using the model included a wide range of infilled frame geometric properties. The results showed in detail the difference in one-way and two-way arching in terms of both strength and failure mechanism, and the contributing factors to this difference. Evaluation of the two main design equations for out-of-plane strength of masonry infills led to proposal of modifications to provide a more rational consideration of directional behaviour of concrete masonry infills. A comparison study using the available test results showed a marked improvement of strength prediction based on the proposed modification.

Effect of Bend Angle on Plastic Limit Loads of Pipe Bends Under In-Plane Bending Moment

2016 ◽  
Author(s):  
Shunjie Li ◽  
Changyu Zhou ◽  
Jian Li ◽  
Xinting Miao
Keyword(s):  
Finite Element ◽  
Stress Concentration ◽  
Large Strain ◽  
Large Angle ◽  
Three Dimensional ◽  
Bending Moment ◽  
Limit Load ◽  
Bend Angle ◽  
Plastic Limit ◽  
Limit Loads

The effect of bend angle on plastic limit loads of pipe bends (elbows) under in-plane opening and closing bending moment is presented using three-dimensional large strain nonlinear finite element analyses. The results show that the presence of ovality significantly leads to the stress concentration in the middle cross section, which is the critical section of pipe bends. Meanwhile the state of stress concentration is also associated with the loading modes including the in-plane opening bending moment and the closing bending moment. Then plastic limit loads of pipe bends are further studied. It is found that plastic limit loads are decreasing with the increase of bend angles. Especially the variation of plastic limit loads of small angle pipe bends (bend angle from the 0 degree to 90 degree) is larger than that of large angle pipe bends (bend angle greater than 90 degree). Based on the finite element results, the present plastic limit load solutions are not fit for the large angle pipe bends (bend angle greater than 90 degree).

Plastic Limit Analysis of an Elbow with Various Wall-Thinning Geometries

2008 ◽  
Vol 385-387 ◽  
pp. 833-836
Author(s):  
Sang Min Lee ◽  
Young Hwan Choi ◽  
Hae Dong Chung ◽  
Yoon Suk Chang ◽  
Young Jin Kim
Keyword(s):  
Nuclear Power ◽  
Three Dimensional ◽  
Bending Moment ◽  
Limit Load ◽  
Nuclear Industry ◽  
Bend Angle ◽  
Piping System ◽  
Plastic Limit ◽  
Limit Loads ◽  
Wall Thinning

A piping system including straight pipes, elbows and tee branches in a nuclear power plant is mostly subjected to severe loading conditions with high temperature and pressure. In particular, the wall-thinning of an elbow due to flow accelerated corrosion is one of safety issues in the nuclear industry. In this respect, it is necessary to investigate the limit loads of an elbow with a wall-thinned part for evaluating integrity. In this paper, three dimensional plastic limit analyses are performed to obtain limit loads of an elbow with different bend angles as well as defect geometries under internal pressure and in-plane/out-of-plane bending moment. The limit loads are also compared with the results from limit load solutions of an uninjured elbow based on the von Mises yield criteria. Finally, the effects of significant factors, bend angle and defect shape, are quantified to estimate the exact load carrying capacity of an elbow during operation.

Effect of Mechanical Model on Limit Load Analysis of High Pressure Heater Tubesheet

2017 ◽  
Author(s):  
Yan-Nan Du ◽  
Xiao-Ying Tang ◽  
Jia-huan Wang ◽  
Zhi-Gang Yang ◽  
Yi-Feng Ren ◽  
...  
Keyword(s):  
High Pressure ◽  
Mechanical Model ◽  
High Stress ◽  
Local Stress ◽  
Limit Load ◽  
Element Model ◽  
Plastic Collapse ◽  
Analysis Design ◽  
Load Analysis ◽  
Collapse Assessment

Tubesheet is the main part of high pressure heater, which is very thick based on chinese code GB151 for the design of heat exchangers. Increased tubesheet with large thermal stress are not conducive to manufacture, heat transmission and detection. The stress and structure of tubesheet are so complex that the time costs too large during the analysis design, and stress classification exists uncertainty. Limit load method contributes to tubesheet lightweight. 3-D finite element model used for analysis design should be simplified reasonably. In this paper, the effect of mechanical model on limit load analysis of high pressure heater tubesheet conforming to the design-by-analysis code is researched. It is found that the tubesheet could pass the plastic collapse assessment, and the thickness of tubesheet could be decreased. The difference between the equivalent sold tubesheet model and the whole tubesheet model exists during plastic collapse assessment. Though the local stress distribution is different, the limit load results occurred plastic collapse by the equivalent sold tubesheet model is close to that by the whole tubesheet model. The limit load occurred plastic collapse is influenced by max circular diameter of tube layout little. The reason is attributed to original tubesheet owning enough rigidity related to thickness, and high stress appeares on the inner wall of jointing of tubesheet with head. The equivalent sold tubesheet model could be used for primary evaluation of limit load, and the whole tubesheet model is suited for partial analysis. The results provide some reference for the design-by-analysis of high pressure heater tubesheet.

scholarly journals Significance of geotechnical loads on local buckling response of buried pipelines with respect to conventional practice

2013 ◽  
Vol 50 (1) ◽  
pp. 68-80 ◽  
Author(s):  
Hiva Mahdavi ◽  
Shawn Kenny ◽  
Ryan Phillips ◽  
Radu Popescu
Keyword(s):  
Load Transfer ◽  
Mechanical Performance ◽  
Three Dimensional ◽  
Local Buckling ◽  
Element Model ◽  
Combined Loading ◽  
Buried Pipelines ◽  
Buried Pipe ◽  
Limit States ◽  
New Criterion

Long-term large deformation geohazards can impose excessive deformation on a buried pipeline. The ground displacement field may initiate pipeline deformation mechanisms that exceed design acceptance criteria with respect to serviceability requirements or ultimate limit states. The conventional engineering approach to define the mechanical performance of pipelines has been based on combined loading events for in-air conditions. This methodology may be conservative, as it ignores the soil effect that imposes geotechnical loads, and also provides restraint, on buried pipelines. The importance of pipeline–soil interaction and load-transfer mechanisms that may affect local buckling of buried pipelines is not well understood. A three-dimensional continuum finite element model, simulating the local buckling response of a buried pipe, using the software package ABAQUS/Standard was developed and calibrated. A comprehensive parametric study was previously conducted to investigate the effect of several parameters on local buckling response of pipelines buried in firm clay. A new strain criterion for local buckling of buried pipelines in firm clay through response surface methodology was developed. In this paper, the new criterion is compared with several existing in-air criteria to study the effect of soil restraint on the local buckling response of buried pipelines. The criterion developed in this study predicts greater characteristic critical strain capacity than in-air based criteria that highlights the influence of soil restraint.

Numerical Simulation on Spiral Hot Bending Process for End Sheet of Tubular Pile

2012 ◽  
Vol 562-564 ◽  
pp. 1373-1376
Author(s):  
Shi Min Xu ◽  
Hua Gui Huang ◽  
Deng Yue Sun
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Radial Direction ◽  
Three Dimensional ◽  
Element Model ◽  
Manufacturing Method ◽  
Forming Technology ◽  
Bending Process ◽  
Simulation Results ◽  
The Moment

A new manufacturing method of spiral hot bending process for the end sheet of tubular pile was introduced in this paper. A three-dimensional (3-D) thermal-mechanical coupled elastic-plasticity finite element model was setup to simulate the hot bending process, and then, the section deformation mechanism from hot bar by rolling to the end sheet has been investigated from the simulation results. The industry manufacture conditions show that the efficiency and quality has been highly improved by the spiral hot bending process. The thickness variety along the radial direction of the workpiece has also been analyzed, the moment and force during the hot bending was also presented in this paper. These conclusions obtained can guide for the forming technology making for both the end sheet of tubular pile and other ring parts.

scholarly journals Inf–sup conditions on convex cones and applications to limit load analysis

2019 ◽  
Vol 24 (10) ◽  
pp. 3331-3353 ◽  
Author(s):  
Jaroslav Haslinger ◽  
Stanislav Sysala ◽  
Sergey Repin
Keyword(s):  
Yield Criterion ◽  
Failure Mechanisms ◽  
Limit Load ◽  
Convex Cones ◽  
Mesh Adaptivity ◽  
Limit Loads ◽  
Perfectly Plastic ◽  
Dual Cones ◽  
Geotechnical Stability ◽  
Load Analysis

The paper is devoted to a family of specific inf–sup conditions generated by tensor-valued functions on convex cones. First, we discuss the validity of such conditions and estimate the value of the respective constant. Then, the results are used to derive estimates of the distance to dual cones, which are required in the analysis of limit loads of perfectly plastic structures. The equivalence between the static and kinematic approaches to limit analysis is proven and computable majorants of the limit load are derived. Particular interest is paid to the Drucker–Prager yield criterion. The last section exposes a collection of numerical examples including basic geotechnical stability problems. The majorants of the limit load are computed and expected failure mechanisms of structures are visualized using local mesh adaptivity.

Sign in / Sign up

Export Citation Format

Share Document