Controlling Gasoline Low Temperature Combustion by Diesel Micro Pilot Injection

2012 ◽  
Vol 134 (7) ◽  
Author(s):  
Johannes Eichmeier ◽  
Uwe Wagner ◽  
Ulrich Spicher
Keyword(s):  
Low Temperature ◽  
Combustion Process ◽  
Pressure Rise ◽  
Reaction Rates ◽  
Pollutant Emissions ◽  
Experimental Investigations ◽  
Injection Timing ◽  
Pilot Injection ◽  
Low Temperature Combustion ◽  
Temperature Combustion

The simultaneous reduction of fuel consumption and pollutant emissions, namely NOx and soot, is the predominant goal in modern engine development. In this context, low temperature combustion concepts are believed to be the most promising approaches to resolve the above mentioned conflict of goals. Disadvantageously these combustion concepts show high peak pressures or high rates of pressure rise due to early ignition and high reaction rates especially at high loads. Furthermore, there are still challenges in controlling combustion phasing. In this context using a small amount of pilot diesel injected directly into the combustion chamber to ignite a highly diluted gasoline air mixture can overcome the aforementioned difficulties. As the gasoline does not ignite without the diesel, the pilot injection timing can be used to control combustion phasing. By increasing dilution even high loads with low rates of pressure rise and without knocking are possible. This paper shows the results of experimental investigations carried out on a heavy duty boosted single cylinder diesel engine. Based on the indicated cylinder pressure, the combustion process is characterized by performing knock analyses as well as thermodynamic analyses. Furthermore, an optically accessible engine has been set up to investigate both the diesel injection and the combustion process by means of digital high speed imaging. Together with the thermodynamic analyses the results of these optical investigations make up the base for the presented theoretical model of this combined diesel-gasoline combustion process. To show the load potential of this Dual-Fuel-CAI concept, the engine was operated at 2100 1/min with an IMEP of 19 bar. NOx emissions did not exceed 0.027 g/kWh.

Controlling Gasoline Low Temperature Combustion by Diesel Micro Pilot Injection

2011 ◽  
Author(s):  
Johannes Eichmeier ◽  
Uwe Wagner ◽  
Ulrich Spicher
Keyword(s):  
Low Temperature ◽  
Combustion Process ◽  
Pressure Rise ◽  
Reaction Rates ◽  
Pollutant Emissions ◽  
Experimental Investigations ◽  
Injection Timing ◽  
Pilot Injection ◽  
Low Temperature Combustion ◽  
Temperature Combustion

The simultaneous reduction of fuel consumption and pollutant emissions, namely NOx and soot, is the predominant goal in modern engine development. In this context, low temperature combustion concepts are believed to be the most promising approaches to resolve the above mentioned conflict of goals. Disadvantageously these combustion concepts show high peak pressures or high rates of pressure rise due to early ignition and high reaction rates especially at high loads. Furthermore, there are still challenges in controlling combustion phasing. In this context using a small amount of pilot Diesel injected directly into the combustion chamber to ignite a highly diluted gasoline air mixture can overcome the aforementioned difficulties. As the gasoline does not ignite without the Diesel, the pilot injection timing can be used to control combustion phasing. By increasing dilution even high loads with low rates of pressure rise and without knocking are possible. This paper shows the results of experimental investigations carried out on a heavy duty boosted single cylinder Diesel engine. Based on the indicated cylinder pressure, the combustion process is characterised by performing knock analyses as well as thermodynamic analyses. Furthermore an optically accessible engine has been set up to investigate both the Diesel injection and the combustion process by means of digital high speed imaging. Together with the thermodynamic analyses the results of these optical investigations make up the base for the presented theoretical model of this combined Diesel gasoline combustion process. To show the load potential of this Dual-Fuel-CAI concept, the engine was operated at 2100 1/min with an IMEP of 19 bar. NOx emissions did not exceed 0.027 g/kWh.

scholarly journals Impact of injection strategies on combustion characteristics, efficiency and emissions of gasoline compression ignition operation in a heavy-duty multi-cylinder engine

2018 ◽  
Vol 21 (8) ◽  
pp. 1426-1440 ◽  
Author(s):  
Buyu Wang ◽  
Michael Pamminger ◽  
Ryan Vojtech ◽  
Thomas Wallner
Keyword(s):  
High Temperature ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Pressure Rise ◽  
Pilot Injection ◽  
Low Temperature Combustion ◽  
Compression Ignition ◽  
Temperature Combustion ◽  
Gas Recirculation ◽  
Direct Fuel Injection

Gasoline compression ignition using a single gasoline-type fuel for direct/port injection has been shown as a method to achieve low-temperature combustion with low engine-out NOx and soot emissions and high indicated thermal efficiency. However, key technical barriers to achieving low-temperature combustion on multi-cylinder engines include the air handling system (limited amount of exhaust gas recirculation) as well as mechanical engine limitations (e.g. peak pressure rise rate). In light of these limitations, high-temperature combustion with reduced amounts of exhaust gas recirculation appears more practical. Furthermore, for high-temperature gasoline compression ignition, an effective aftertreatment system allows high thermal efficiency with low tailpipe-out emissions. In this work, experimental testing was conducted on a 12.4 L multi-cylinder heavy-duty diesel engine operating with high-temperature gasoline compression ignition combustion with port and direct injection. Engine testing was conducted at an engine speed of 1038 r/min and brake mean effective pressure of 1.4 MPa for three injection strategies, late pilot injection, early pilot injection, and port/direct fuel injection. The impact on engine performance and emissions with respect to varying the combustion phasing were quantified within this study. At the same combustion phasing, early pilot injection and port/direct fuel injection had an earlier start of combustion and higher maximum pressure rise rates than late pilot injection attributable to more premixed fuel from pilot or port injection; however, brake thermal efficiencies were higher with late pilot injection due to reduced heat transfer. Early pilot injection also exhibited the highest cylinder-to-cylinder variations due to differences in injector behavior as well as the spray/wall interactions affecting mixing and evaporation process. Overall, peak brake thermal efficiency of 46.1% and 46% for late pilot injection and port/direct fuel injection was achieved comparable to diesel baseline (45.9%), while early pilot injection showed the lowest brake thermal efficiency (45.3%).

Effects of fuel properties on combustion and pollutant emissions of a low temperature combustion mode diesel engine

Fuel ◽  
2020 ◽  
Vol 267 ◽  
pp. 117123 ◽  
Author(s):  
Song Li ◽  
Jinping Liu ◽  
Yu Li ◽  
Mingrui Wei ◽  
Helin Xiao ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Low Temperature ◽  
Fuel Properties ◽  
Pollutant Emissions ◽  
Low Temperature Combustion ◽  
Combustion Mode ◽  
Temperature Combustion

A Computational Investigation of the Impact of Multiple Injection Strategies on Combustion Efficiency in Diesel-Natural Gas Dual Fuel Low Temperature Combustion Engine

2019 ◽  
Author(s):  
Lorenzo Bartolucci ◽  
Stefano Cordiner ◽  
Vincenzo Mulone ◽  
Sundar R. Krishnan ◽  
Kalyan K. Srinivasan
Keyword(s):  
Experimental Data ◽  
Low Temperature ◽  
Natural Gas ◽  
Combustion Efficiency ◽  
Dual Fuel ◽  
Pilot Injection ◽  
Low Temperature Combustion ◽  
Single Cylinder ◽  
Temperature Combustion ◽  
The Impact

Abstract Dual fuel diesel-methane low temperature combustion (LTC) has been investigated by various research groups, showing high potential for emissions reduction (especially oxides of nitrogen (NOx) and particulate matter (PM)) without adversely affecting fuel conversion efficiency in comparison with conventional diesel combustion. However, when operated at low load conditions, dual fuel LTC typically exhibit poor combustion efficiencies. This behavior is mainly due to low bulk gas temperatures under lean conditions, resulting in unacceptably high carbon monoxide (CO) and unburned hydrocarbon (UHC) emissions. A feasible and rather innovative solution may be to split the pilot injection of liquid fuel into two injection pulses, with the second pilot injection supporting the methane combustion once the process is initiated by the first one. In this work, diesel-methane dual fuel LTC is investigated numerically in a single-cylinder heavy-duty engine operating at 5 bar brake mean effective pressure (BMEP) at 85% and 75% percentage of energy substitution (PES) by methane (taken as a natural gas surrogate). A multidimensional model is first validated in comparison with experimental data obtained on the same single-cylinder engine for early single pilot diesel injection at 310 CAD and 500 bar rail pressure. With the single pilot injection case as baseline, the effects of multiple pilot injections and different rail pressures on combustion emissions are investigated, again showing good agreement with experimental data. Apparent heat release rate and cylinder pressure histories as well as combustion efficiency trends are correctly captured by the numerical model. Results prove that higher rail pressures yield reductions of HC and CO by 90% and 75%, respectively, at the expense of NOx emissions, which increase by ∼30% from baseline. Furthermore, it is shown that post-injection during the expansion stroke does not support the stable development of the combustion front as the combustion process is confined close to the diesel spray core.

scholarly journals A Review on Homogeneous Charge Compression Ignition and Low Temperature Combustion by Optical Diagnostics

2015 ◽  
Vol 2015 ◽  
pp. 1-23 ◽  
Author(s):  
Chao Jin ◽  
Zunqing Zheng
Keyword(s):  
Low Temperature ◽  
Chemical Reaction ◽  
Homogeneous Charge Compression Ignition ◽  
Optical Diagnostics ◽  
Diagnostic Methods ◽  
Pollutant Emissions ◽  
Low Temperature Combustion ◽  
Compression Ignition ◽  
Temperature Combustion ◽  
Homogeneous Charge

Optical diagnostics is an effective method to understand the physical and chemical reaction processes in homogeneous charge compression ignition (HCCI) and low temperature combustion (LTC) modes. Based on optical diagnostics, the true process on mixing, combustion, and emissions can be seen directly. In this paper, the mixing process by port-injection and direct-injection are reviewed firstly. Then, the combustion chemical reaction mechanism is reviewed based on chemiluminescence, natural-luminosity, and laser diagnostics. After, the evolution of pollutant emissions measured by different laser diagnostic methods is reviewed and the measured species including NO, soot, UHC, and CO. Finally, a summary and the future directions on HCCI and LTC used optical diagnostics are presented.

Operating Limits of Spark-Assisted Compression Ignition Combustion Under Boosted Ultra-EGR Dilute Conditions in a Negative Valve Overlap Engine

2019 ◽  
Author(s):  
Vassilis Triantopoulos ◽  
Jason B. Martz ◽  
Jeff Sterniak ◽  
George Lavoie ◽  
Dennis N. Assanis ◽  
...  
Keyword(s):  
Low Temperature ◽  
Heat Release ◽  
Engine Speed ◽  
Pressure Rise ◽  
Stability Limit ◽  
Maximum Pressure ◽  
Low Temperature Combustion ◽  
Compression Ignition ◽  
Temperature Combustion ◽  
Operating Limits

Abstract Spark-assisted compression ignition (SACI) is a low temperature combustion mode that can offer thermal efficiency improvements and lower nitrogen oxide emissions compared to conventional spark-ignited combustion. However, the SACI operating range is often limited due to excessive pressure rise rates driven by rapid heat release rates. Well-controlled experiments were performed to investigate the SACI operating limits under previously unexplored boosted, stoichiometric, EGR dilute conditions, where low temperature combustion engines promise high thermodynamic efficiencies. At higher intake boost, the SACI high load limit shifted towards lower fuel-to-charge equivalence ratio mixtures, creating a larger gap between the conventional spark-ignition EGR dilution limit and the boosted SACI operating limits. Combustion phasing retard was very effective at reducing maximum pressure rise rate levels until the stability limit, primarily due to slower end-gas burn rates. Gross fuel conversion efficiency improvements up to 10% were observed by using intake boost for either load expansion or dilution extension. Changes in engine speed necessitated changes in unburned gas temperature to match autoignition timing, but were shown to have negligible impact on the heat release profile on a crank angle basis. Lower engine speeds were favorable for load expansion, as time-based peak pressure rise rates scaled with engine speed.

Sign in / Sign up

Export Citation Format

Share Document