Analytical Solution of the Graetz Problem Extended to Slip-Flow in Microtube

2012 ◽  
Vol 134 (10) ◽  
Author(s):  
Fayao Xu ◽  
Hugen Ma
Keyword(s):  
Analytical Solution ◽  
Energy Equation ◽  
Temperature Jump ◽  
Separation Of Variables ◽  
Slip Flow ◽  
Power Series Expansion ◽  
Velocity Slip ◽  
Jump Condition ◽  
Dimensionless Temperature ◽  
Graetz Problem

The original Graetz problem is extended to slip-flow in microtube. The extended Graetz problem in slip-flow with the isothermal boundary condition on the wall was solved using conventional energy equation with both the velocity slip and the temperature jump condition of slip-flow. The analytical solution was obtained by solving the energy equation with the method of separation of variables. The accurate eigenvalues were obtained by solving the eigenfunction with the method of power series expansion. In the end, temperature distributions, local Nusselt number Nux, and dimensionless temperature jump θs were obtained. In addition, the influences of Knudsen number Kn on Nux, Nu∞, and θs were discussed.

On Temperature Jump Condition for Slip Flow in a Microchannel With Constant Wall Temperature

2017 ◽  
Vol 139 (7) ◽  
Author(s):  
Yutaka Asako ◽  
Chungpyo Hong
Keyword(s):  
Boundary Condition ◽  
Viscous Dissipation ◽  
Wall Temperature ◽  
Energy Equation ◽  
Temperature Jump ◽  
Slip Flow ◽  
Jump Condition ◽  
Constant Wall Temperature ◽  
Maximum Heat ◽  
Maximum Heat Transfer

The analytical solution in the fully developed region of a slip flow in a circular microtube with constant wall temperature is obtained to verify the conventional temperature jump boundary condition when both viscous dissipation (VD) and substantial derivative of pressure (SDP) terms are included in the energy equation. Although the shear work term is not included in the conventional temperature jump boundary condition explicitly, it is verified that the conventional temperature jump boundary condition is valid for a slip flow in a microchannel with constant wall temperature when both viscous dissipation and substantial derivative of pressure terms are included in the energy equation. Numerical results are also obtained for a slip flow in a developing region of a circular tube. The results showed that the maximum heat transfer rate decreases with increasing Mach number.

The Graetz Problem for the Ellis Fluid Model

2018 ◽  
Vol 74 (1) ◽  
pp. 15-24 ◽  
Author(s):  
N. Ali ◽  
M.W.S. Khan
Keyword(s):  
Energy Equation ◽  
Fluid Model ◽  
Separation Of Variables ◽  
Surface Heat ◽  
Thermal Boundary Conditions ◽  
Nusselt Numbers ◽  
Graetz Problem ◽  
Developing Flow ◽  
Sturm Liouville

AbstractThe determination of temperature and auxiliary quantities such as local and average Nusselt numbers for thermally developing flow is referred as the Graetz problem. In the classical Graetz problem, the fluid entering the tube or channel is Newtonian in nature. Here, an extension of the classical Graetz problem is presented by assuming that the fluid entering the tube or channel obeys the Ellis constitutive equation. The energy equation for the considered problem is solved using the separation of variables technique supplemented with the MATLAB routine bvp4c for computation of the eigenvalues and numerical solution of the associated Sturm-Liouville boundary value problem. The problem is solved for two types of thermal boundary conditions, namely, uniform surface temperature and uniform surface heat flux for both flat and circular geometries. Expressions for bulk mean temperature and local and average Nusselt numbers are presented and discussed through tables and graphs.

Zero Mass Flux Dependent on Radiative Magnetohydrodynamics Carreau Nanofluid Over a Radially Surface with Temperature Jump and Slip Flow: A Hybrid Nanofluid Analysis

2021 ◽  
Vol 10 (1) ◽  
pp. 118-127
Author(s):  
Amit Parmar ◽  
Rakesh Choudhary ◽  
Krishna Agrawal
Keyword(s):  
Mass Flux ◽  
Temperature Jump ◽  
Slip Flow ◽  
Velocity Slip ◽  
Concentration Profiles ◽  
Fluid Temperature ◽  
Slip Parameter ◽  
First Order ◽  
Zero Mass ◽  
Carreau Nanofluid

The present study explores the slip flow and heat transfer induced by a radially surface with MHD Carreau nanofluid. In addition, the effects of temperature jump, non-linear radiation and the dependent zero mass flux also taken into account. This study also considers the cross-diffusion effect on temperature and concentration governing profiles. Appropriate transformations are engaged in order to acquire nonlinear differential equations (ODEs) from the partial differential system, their solutions are obtained by Runge-Kutta 4th order with shooting scheme in MATLAB. The impact of pertinent flow parameters such as first and second order velocity slip parameter, temperature jump, magnetic parameter, heat source, radiation parameter, melting surface parameter, temperature ratio parameter on dimensionless velocity, temperature and concentration profiles achieved graphically as well as local skin friction, Nusselt number and Sherwood number are demonstrated in the form of Table. first order velocity slip parameter (slip1) on f′, Θ and Φ profile fields. With an increment in the velocity slip first order parameter (slip1) we have perceived a fall in the momentum boundary layer and concentration profiles and a growth in the fluid temperature field.

scholarly journals Gas Microflows in the Slip Flow Regime: A Critical Review on Convective Heat Transfer

2011 ◽  
Vol 134 (2) ◽  
Author(s):  
Stéphane Colin
Keyword(s):  
Heat Transfer ◽  
Convective Heat Transfer ◽  
Flow Regime ◽  
Convective Heat ◽  
Temperature Jump ◽  
Numerical Models ◽  
Slip Flow ◽  
Velocity Slip ◽  
Constant Wall Temperature ◽  
Slip Flow Regime

Accurate modeling of gas microvection is crucial for a lot of MEMS applications (microheat exchangers, pressure gauges, fluidic microactuators for active control of aerodynamic flows, mass flow and temperature microsensors, micropumps, and microsystems for mixing or separation for local gas analysis, mass spectrometers, vacuum, and dosing valves…). Gas flows in microsystems are often in the slip flow regime, characterized by a moderate rarefaction with a Knudsen number of the order of 10−2–10−1. In this regime, velocity slip and temperature jump at the walls play a major role in heat transfer. This paper presents a state of the art review on convective heat transfer in microchannels, focusing on rarefaction effects in the slip flow regime. Analytical and numerical models are compared for various microchannel geometries and heat transfer conditions (constant heat flux or constant wall temperature). The validity of simplifying assumptions is detailed and the role played by the kind of velocity slip and temperature jump boundary conditions is shown. The influence of specific effects, such as viscous dissipation, axial conduction and variable fluid properties is also discussed.

Three Dimensional Numerical Analysis of Laminar Slip-Flow Heat Transfer in Rectangular Microchannels

2008 ◽  
Author(s):  
H. D. Madhawa Hettiarachchi ◽  
Mihajlo Golubovic ◽  
William M. Worek
Keyword(s):  
Heat Transfer ◽  
Boundary Condition ◽  
Temperature Jump ◽  
Slip Flow ◽  
Three Dimensional ◽  
Velocity Slip ◽  
Thermal Boundary Condition ◽  
Navier Stokes ◽  
Constant Wall Temperature ◽  
Rectangular Microchannels

Slip-flow and heat transfer in rectangular microchannels are studied numerically for constant wall temperature (T) and constant wall heat flux (H2) boundary conditions under thermally developing flow. Navier-Stokes and energy equations with velocity slip and temperature jump at the boundary are solved using finite volume method in a three dimensional cartesian coordinate system. A modified convection-diffusion coefficient at the wall-fluid interface is defined to incorporate the temperature-jump boundary condition. Validity of the numerical simulation procedure is stabilized. The effect of rarefaction on heat transfer in the entrance region is analyzed in detail. The velocity slip has an increasing effect on the Nusselt (Nu) number whereas temperature jump has a decreasing effect, and the combined effect could result increase or decrease in the Nu number. For the range of parameters considered, there could be high as 15% increase or low as 50% decrease in fully developed Nu is plausible for T thermal boundary condition while it could be high as 20% or low as 35% for H2 thermal boundary condition.

Numerical Modeling of Micro Fin Arrays Using Slip Flow and Temperature Jump Boundary Conditions

2008 ◽  
Author(s):  
C. B. Sobhan ◽  
Muhsin M. Ameen ◽  
Praveen P. Abraham
Keyword(s):  
Heat Transfer ◽  
Boundary Conditions ◽  
Temperature Jump ◽  
Slip Flow ◽  
Convection Heat Transfer ◽  
Transient State ◽  
Velocity Slip ◽  
Operating Pressure ◽  
Parametric Studies ◽  
Explicit Finite Difference

A numerical investigation of natural convection heat transfer from a rectangular fin array of microscale dimensions, where a “down and up” flow pattern occurs, is carried out. The stream function vorticity formulation is used in the analysis and the governing equations of the transient two dimensional field are solved using an explicit finite difference scheme. The dimensions of the domain are such that the problem falls under the slip flow regime. The non continuum effects are modeled through Maxwell’s velocity slip and Smoluchowski’s temperature jump boundary conditions. The steady state velocity and temperature distributions in the field are obtained by marching through the transient state. The average heat transfer coefficient and the Nusselt Number are calculated. The influence of the fin spacing, fin height and operating pressure on the performance of the fin array is studied through parametric studies and some conclusions are drawn regarding the significance of non continuum effects in the micro scale dimensions considered.

An analytical solution for natural convective gas microflow in a tall vertical enclosure

2010 ◽  
Vol 225 (1) ◽  
pp. 145-154 ◽  
Author(s):  
H S Panda ◽  
S Ghosh Moulic
Keyword(s):  
Nusselt Number ◽  
Analytical Solution ◽  
Stokes System ◽  
Slip Flow ◽  
Velocity Slip ◽  
Boussinesq Approximation ◽  
Navier Stokes ◽  
First Order ◽  
Vertical Walls ◽  
Slip Flow Regime

An analytical solution for buoyancy-induced gas microflow in a tall differentially heated enclosure with isothermal vertical walls is presented. The Navier—Stokes system has been solved. The Boussinesq approximation has been employed. Wall—fluid interactions are modelled by first-order velocity slip and temperature jump conditions. The analysis presented covers continuum to slip-flow regime. A functional form for the Nusselt number has been derived analytically. The results indicate that as the Knudsen number increases, the Nusselt number decreases.

Hydromagnetic flow and heat transfer with various nanoparticle additives past a wedge with high order velocity slip and temperature jump

2017 ◽  
Vol 95 (5) ◽  
pp. 440-449 ◽  
Author(s):  
Qianfang Liu ◽  
Jing Zhu ◽  
Bandar Bin-Mohsin ◽  
Liancun Zheng
Keyword(s):  
Heat Transfer ◽  
Temperature Jump ◽  
Slip Flow ◽  
Velocity Slip ◽  
Skin Friction Coefficient ◽  
High Order ◽  
Solid Particles ◽  
Flow And Heat Transfer ◽  
Homotopy Analysis ◽  
Fundamental Equations

Nanofluid slip flow with distinct solid particles past a wedge with convective surface and high order slip is discussed in this paper. The wedge model is modified by considering the effects of Brownian motion and thermophphoresis together with the high order velocity slip and temperature jump. In this study, the governing fundamental equations are first transformed into third-order ordinary differential equations and solved by using the homotopy analysis method (HAM). Through error analysis and comparison with previous research, the effectiveness of HAM is ascertained, and the crucial influence of nanoparticles and high-order slip on the fluid skin-friction coefficient and heat transfer coefficient is analyed. Thermophphoresis parameter and suction/injection parameter are found to cause an increase in velocity and temperature. The rate of heat transfer in the Cu–water nanofluid is found to be higher than the others.

Slip Flow Structures in Confined Geometries

2008 ◽  
Author(s):  
Steffen Jebauer ◽  
Justyna Czerwinska
Keyword(s):  
Gas Flow ◽  
Temperature Jump ◽  
Complex Structure ◽  
Slip Flow ◽  
Velocity Slip ◽  
Navier Stokes ◽  
Flow Structures ◽  
Complex Flow ◽  
Vortex Patterns ◽  
Slip Flows

This paper presents various flow structures related to velocity slip and temperature jump in very low Reynolds number gas flow. The structures differ significantly from the ones observed in continuum regime for laminar flow, especially if the geometry has complex structure, which is very often the case in microfluidic devices. We are modelling the flow as a continuum Navier-Stokes gas flow with additional velocity slip and temperature jump boundary conditions for curved surfaces for slip flows with Knudsen numbers Kn < 0.1. For complex channel geometries with obstacles and curved walls vortex patterns are observed that are related to the thermal stress slip flow. This type of flow is induced only when non-uniform temperature distributions inside flow domains are present. The investigated geometries consist of one or more cylinder walls with diameters of up to a few 100 μm placed inside of confined microchannels, with all setups being two-dimensional. In gaseous microdevices the resulting complex flow patterns can be utilised to enhance mixing or heat transfer.

Sign in / Sign up

Export Citation Format

Share Document