Rounded Cutting Edge Model for the Prediction of Bone Sawing Forces

2012 ◽  
Vol 134 (7) ◽  
Author(s):  
Thomas P. James ◽  
John J. Pearlman ◽  
Anil Saigal
Keyword(s):  
Cutting Force ◽  
High Speed ◽  
Orthogonal Cutting ◽  
Friction Model ◽  
Cutting Edge ◽  
Resultant Force ◽  
Hertzian Contact ◽  
Depth Of Cut ◽  
Force Magnitude ◽  
Variable Friction

A new analytical model to predict bone sawing forces is presented. Development of the model was based on the concept of a single tooth sawing at a depth of cut less than the cutting edge radius. A variable friction model was incorporated as well as elastic Hertzian contact stress to determine a lower bound for the integration limits. A new high speed linear apparatus was developed to simulate cutting edge speeds encountered with sagittal and reciprocating bone saws. Orthogonal cutting experiments in bovine cortical bone were conducted for comparison to the model. A design of the experiment’s approach was utilized with linear cutting speeds between 2600 and 6200 mm/s for depths of cut between 2.5 and 10 μm. Resultant forces from the design of experiments were in the range of 8 to 11 N, with higher forces at greater depths of cut. Model predictions for resultant force magnitude were generally within one standard deviation of the measured force. However, the model consistently predicted a thrust to cutting force ratio that was greater than measured. Consequently, resultant force angles predicted by the model were generally 20 deg higher than calculated from experimental thrust and cutting force measurements.

scholarly journals Machinability of Scots pine during peripheral milling with helical cutters

BioResources ◽  
2021 ◽  
Vol 16 (4) ◽  
pp. 8172-8183
Author(s):  
Dong Jin ◽  
Kejun Wei
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Scots Pine ◽  
Inclination Angle ◽  
Cutting Speed ◽  
Cutting Edge ◽  
Resultant Force ◽  
Orthogonal Experimental Design ◽  
Depth Of Cut ◽  
Peripheral Milling

Scots pine (Pinus sylvestris L.) is a fast-growing wood that has been widely manufactured into various furnishing products. To improve the machinability of Scots pine, the cutting force and surface roughness during peripheral milling with helical cutters was assessed via an orthogonal experimental design. Experimental results revealed that the resultant cutting force is positively related to the depth of cut, but negatively correlated with inclination angle of cutting edge and cutting speed. However, surface roughness first declines and then increases with increasing inclination angle, and it also shows an increasing trend with the increasing depth of cut and decreasing cutting speed. Furthermore, the depth of cut significantly contributes to the resultant force and surface roughness, while both the cutting speed and inclination angle have insignificant impacts on the resultant force and surface roughness. Finally, the optimized milling parameters were determined as 62° inclination angle of cutting edge, 45 m/min cutting speed, and 0.2 mm depth of cut, and these parameters are proposed for the quality finishing of Scots pine machining.

scholarly journals Influence of tool edge form factor and cutting parameters on milling performance

2021 ◽  
Vol 13 (4) ◽  
pp. 168781402110090
Author(s):  
Xuefeng Zhao ◽  
Hao Qin ◽  
Zhiguo Feng
Keyword(s):  
Form Factor ◽  
Simulation Model ◽  
Cutting Force ◽  
Surface Quality ◽  
High Speed ◽  
Orthogonal Cutting ◽  
Cutting Temperature ◽  
Tool Edge ◽  
Drag Finishing ◽  
Edge Preparation

Tool edge preparation can improve the tool life, as well as cutting performance and machined surface quality, meeting the requirements of high-speed and high-efficiency cutting. In general, prepared tool edges could be divided into symmetric or asymmetric edges. In the present study, the cemented carbide tools were initially edge prepared through drag finishing. The simulation model of the carbide cemented tool milling steel was established through Deform software. Effects of edge form factor, spindle speed, feed per tooth, axial, and radial cutting depth on the cutting force, the tool wear, the cutting temperature, and the surface quality were investigated through the orthogonal cutting simulation. The simulated cutting force results were compared to the results obtained from the orthogonal milling experiment through the dynamometer Kistler, which verified the simulation model correctness. The obtained results provided a basis for edge preparation effect along with high-speed and high effective cutting machining comprehension.

Cutting Temperature and Cutting Forces Investigation Based on the Taguchi Design Method when High-Speed Milling of Titanium Matrix Composites with PCD Tool

2016 ◽  
Vol 836-837 ◽  
pp. 168-174 ◽  
Author(s):  
Ying Fei Ge ◽  
Hai Xiang Huan ◽  
Jiu Hua Xu
Keyword(s):  
Cutting Force ◽  
Feed Rate ◽  
Cutting Forces ◽  
High Speed ◽  
Volume Fraction ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
High Speed Milling ◽  
Radial Depth

High-speed milling tests were performed on vol. (5%-8%) TiCp/TC4 composite in the speed range of 50-250 m/min using PCD tools to nvestigate the cutting temperature and the cutting forces. The results showed that radial depth of cut and cutting speed were the two significant influences that affected the cutting forces based on the Taguchi prediction. Increasing radial depth of cut and feed rate will increase the cutting force while increasing cutting speed will decrease the cutting force. Cutting force increased less than 5% when the reinforcement volume fraction in the composites increased from 0% to 8%. Radial depth of cut was the only significant influence factor on the cutting temperature. Cutting temperature increased with the increasing radial depth of cut, feed rate or cutting speed. The cutting temperature for the titanium composites was 40-90 °C higher than that for the TC4 matrix. However, the cutting temperature decreased by 4% when the reinforcement's volume fraction increased from 5% to 8%.

scholarly journals Cutting Force Prediction Models by FEA and RSM When Machining X56 Steel with Single Diamond Grit

Micromachines ◽  
2021 ◽  
Vol 12 (3) ◽  
pp. 326
Author(s):  
Lan Zhang ◽  
Xianbin Sha ◽  
Ming Liu ◽  
Liquan Wang ◽  
Yongyin Pang
Keyword(s):  
Cutting Force ◽  
Coefficient Of Friction ◽  
High Speed ◽  
Prediction Models ◽  
Pipeline Steel ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Cutting Force Prediction ◽  
Force Prediction ◽  
Diamond Wire Saw

In the field of underwater emergency maintenance, submarine pipeline cutting is generally performed by a diamond wire saw. The process, in essence, involves diamond grits distributed on the surface of the beads cutting X56 pipeline steel bit by bit at high speed. To find the effect of the different parameters (cutting speed, coefficient of friction and depth of cut) on cutting force, the finite element (FEA) method and response surface method (RSM) were adopted to obtain cutting force prediction models. The former was based on 64 simulations; the latter was designed according to DoE (Design of Experiments). Confirmation experiments were executed to validate the regression models. The results indicate that most of the prediction errors were within 10%, which were acceptable in engineering. Based on variance analyses of the RSM models, it could be concluded that the depth of the cut played the most important role in determining the cutting force and coefficient the of friction was less influential. Despite making little direct contribution to the cutting force, the cutting speed is not supposed to be high for reducing the coefficient of friction. The cutting force models are instructive in manufacturing the diamond beads by determining the protrusion height of the diamond grits and the future planning of the cutting parameters.

Effects of Cutting Parameters on Chip Side-Curl Mechanisms and Variable Tool-Chip Contact in Turning

1999 ◽  
Author(s):  
A. K. Balaji ◽  
I. S. Jawahir
Keyword(s):  
High Speed ◽  
Cutting Parameters ◽  
Sem Analysis ◽  
Tool Geometry ◽  
Depth Of Cut ◽  
Nose Radius ◽  
Turning Operations ◽  
Variable Friction ◽  
On Chip ◽  
Bar Turning

Abstract This paper presents the results of an investigative study on the chip side-curling mechanism and the associated variable tool-chip contact in turning operations. The effect of various cutting and tool geometry parameters such as depth of cut-nose radius ratio, feed, inclination angle, etc. on chip side-curling are established in a hierarchical manner. The importance of variable friction at the tool-chip interface along the developed length of the cutting edge is shown from the experimental observations of the tool-chip contact area using a SEM analysis. The significant influence of the radial cutting force component on the resultant chip side-curl is established using a high speed-filming analysis of comparative experiments in tube and bar turning operations.

scholarly journals Optimization of Boring Process Parameters in Manufacturing of Polyacetal Bushing using High Speed Steel

2019 ◽  
Vol 130 ◽  
pp. 01031 ◽  
Author(s):  
The Jaya Suteja ◽  
Yon Haryono ◽  
Andri Harianto ◽  
Esti Rinawiyanti
Keyword(s):  
Surface Roughness ◽  
Process Parameters ◽  
Feed Rate ◽  
High Speed ◽  
Removal Rate ◽  
High Speed Steel ◽  
Cutting Edge ◽  
Depth Of Cut ◽  
Optimum Result ◽  
Edge Angle

Polyacetal is commonly used as bushing material because of its low coefficient of friction and self lubricant characteristics. The polyacetal is machined by using boring process to produce bushing in certain surface roughness. The objectives of this research are to optimize three independent parameters (depth of cut, feed rate and principal cutting edge angle) of boring process of polyacetal using high speed steel tool to achieve the highest material removal rate and the required surface roughness. Response Surface Methodology is used to investigate the influence of the parameters and optimize the boring process. The research shows that the influence of the boring process parameters on polyacetal is similar compared to on metal. The result reveals that the optimum result is achieved by applying the value of depth of cut, feed rate, and principal cutting edge angle is 2.9 × 10–3 m, 0.229 mm rev–1, and 99.1° respectively. By applying these values, the maximum material rate removal achieved in this research is 1263.4 mm3 s–1 and the surface roughness achieved is 1.57 × 10–6 m.

Investigation of Surface Characteristics and Chip Morphology in High Speed Cutting of Inconel718 Based on SHPB System

2019 ◽  
Author(s):  
Zengqiang Wang ◽  
Zhanfei Zhang ◽  
Wenhu Wang ◽  
Ruisong Jiang ◽  
Kunyang Lin ◽  
...  
Keyword(s):  
Surface Roughness ◽  
High Speed ◽  
Split Hopkinson Pressure Bar ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Surface Profile ◽  
Chip Morphology ◽  
Depth Of Cut ◽  
Machined Surface ◽  
High Speed Cutting

Abstract High speed cutting (HSC) technology has the characteristics of high material removal rates and high machining precision. In order to study the relationships between chip morphology and machining surface characteristic in high speed cutting of superalloy Inconel718. High-speed orthogonal cutting experiment are carried out by used a high speed cutting device based on split Hopkinson pressure bar (SHPB). The specimen surfaces and collected chips were then detected with optical microscope, scanning electron microscope and three-dimensional surface profile measuring instrument. The results show that within the experimental parameters (cutting speed from 8–16m/s, depth of cut 0.1–0.5mm), the obtained chips are sawtooth chips and periodic micro-ripple appear on the machined surface. With the cutting speed increases, machining surface roughness is decreases from 1.4 to 0.99μm, and the amplitude of periodic ripples also decreases. With the cutting depth increases, the machining surface roughness increases from 0.96 to 5.12μm and surface topography becomes worse. With the increase of cutting speed and depth of cut, the chips are transform from continues sawtooth to sawtooth fragment. By comparing the frequency of surface ripples and sawtooth chips, it is found that they are highly consistent.

Comparative Study on Cutting Force Simulation Using DEFORM 3D Software during High Speed Machining of Ti-6Al-4V

2020 ◽  
Vol 856 ◽  
pp. 50-56
Author(s):  
Kundan Kumar Prasad ◽  
Santosh Kumar Tamang ◽  
M. Chandrasekaran
Keyword(s):  
Finite Element ◽  
Cutting Force ◽  
High Speed ◽  
Cutting Temperature ◽  
Experimental Result ◽  
Depth Of Cut ◽  
Work Piece ◽  
High Speed Machining ◽  
3D Software ◽  
Deform 3D

The finite element-based machining simulations for evaluation/computation of different machining responses (i.e., cutting temperature, tool wear, cutting force, and power/energy consumption) are investigated by number of researchers. In this work, finite element machining simulation was performed to obtain knowledge about cutting forces during machining of hard materials. Titanium alloy (Ti-6Al-4V) has been increasingly used in aerospace and biomedical applications due to high toughness and good corrosion resistance. The high speed machining (HSM) simulation of Ti-6Al-4V work-piece using carbide tool coated with TiCN has been conducted with different combination of cutting conditions for prediction of main cutting force (Fz). The simulated result obtained from Deform 3D software is validated with experimental result and it was found that the result found in good agreement. The parametric variation shows that depth of cut and feed are influencing parameters on cutting force.

Study on Determination of Friction Model at the Tool-Chip Interface of Titanium Alloy Ti6Al4V Based on Orthogonal Cutting

2011 ◽  
Vol 117-119 ◽  
pp. 1788-1791
Author(s):  
Yue Feng Yuan ◽  
Wu Yi Chen
Keyword(s):  
Titanium Alloy ◽  
Cutting Force ◽  
Metal Cutting ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Friction Model ◽  
Carbide Tool ◽  
Orthogonal Turning ◽  
Titanium Alloy Ti6al4v

It is necessary for cutting simulation to determine the friction model at the tool-chip interface suitable for metal cutting process. Cutting force experiments in orthogonal turning titanium alloy TI6AL4V are carried out with cement carbide tool KW10. The Coulomb frictions at the tool-chip interface are calculated based on measured cutting force, and the friction model is regressed, where cutting speed and feed rate are presented.

Sign in / Sign up

Export Citation Format

Share Document