Three-Dimensional Wing Design Towards the Future Mars Airplane

2011 ◽  
Author(s):  
Ryoji Kojima ◽  
Donghi Lee ◽  
Tomoaki Tatsukawa ◽  
Taku Nonomura ◽  
Akira Oyama ◽  
...  
Keyword(s):  
Reynolds Number ◽  
Aspect Ratio ◽  
Drag Coefficient ◽  
Lift Coefficient ◽  
Three Dimensional ◽  
Aerodynamic Characteristics ◽  
Viscous Drag ◽  
Stream Velocity ◽  
Main Stream ◽  
Lower Reynolds Number

The effects of aspect ratio and Reynolds number on aerodynamic characteristics of three-dimensional rectangular wing at low Reynolds number of 103 to 105, are investigated with Reynolds-averaged Navier-Stokes solver with the Baldwin-Lomax model. Present results show that lift coefficient decreases drastically at lower aspect ratio than 4. Besides, the much larger viscous drag coefficient is obtained at the lower Reynolds number, especially lower than 104. In order to focus on designing practical wings, the particular cases under the condition of fixed wing-surface area and fixed main stream velocity are conducted. The results show that there is trade-off between the decrease in viscous drag coefficient with increasing Reynolds number and the increase in lift coefficient with increasing aspect ratio. At the lower Reynolds number condition, as the former effect is stronger than the latter one, maximum lift-to-drag ratio is obtained at lower aspect ratio.

Experimental Aerodynamic Characteristics of a Compound Wing in Ground Effect

2014 ◽  
Vol 136 (5) ◽  
Author(s):  
Saeed Jamei ◽  
Adi Maimun Abdul Malek ◽  
Shuhaimi Mansor ◽  
Nor Azwadi Che Sidik ◽  
Agoes Priyanto
Keyword(s):  
Reynolds Number ◽  
Drag Coefficient ◽  
Center Of Pressure ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Leading Edge ◽  
Ground Effect ◽  
Reynolds Numbers ◽  
Aerodynamic Characteristics ◽  
Ground Clearance

Wing configuration is a parameter that affects the performance of wing-in-ground effect (WIG) craft. In this study, the aerodynamic characteristics of a new compound wing were investigated during ground effect. The compound wing was divided into three parts with a rectangular wing in the middle and two reverse taper wings with anhedral angle at the sides. The sectional profile of the wing model is NACA6409. The experiments on the compound wing and the rectangular wing were carried to examine different ground clearances, angles of attack, and Reynolds numbers. The aerodynamic coefficients of the compound wing were compared with those of the rectangular wing, which had an acceptable increase in its lift coefficient at small ground clearances, and its drag coefficient decreased compared to rectangular wing at a wide range of ground clearances, angles of attack, and Reynolds numbers. Furthermore, the lift to drag ratio of the compound wing improved considerably at small ground clearances. However, this improvement decreased at higher ground clearance. The drag polar of the compound wing showed the increment of lift coefficient versus drag coefficient was higher especially at small ground clearances. The Reynolds number had a gradual effect on lift and drag coefficients and also lift to drag of both wings. Generally, the nose down pitching moment of the compound wing was found smaller, but it was greater at high angle of attack and Reynolds number for all ground clearance. The center of pressure was closer to the leading edge of the wing in contrast to the rectangular wing. However, the center of pressure of the compound wing was later to the leading edge at high ground clearance, angle of attack, and Reynolds number.

scholarly journals Numerical Analysis of the Aerodynamic Characteristics of NACA-4312 Airfoil

2020 ◽  
Vol 01 (02) ◽  
pp. 29-36
Author(s):  
Md Rhyhanul Islam Pranto ◽  
Mohammad Ilias Inam
Keyword(s):  
Reynolds Number ◽  
Drag Coefficient ◽  
Lift Coefficient ◽  
Turbulence Models ◽  
Aerodynamic Characteristics ◽  
Numerical Results ◽  
Ansys Fluent ◽  
Coefficient Increase ◽  
Lift And Drag ◽  
Lift And Drag Coefficient

The aim of the work is to investigate the aerodynamic characteristics such as lift coefficient, drag coefficient, pressure distribution over a surface of an airfoil of NACA-4312. A commercial software ANSYS Fluent was used for these numerical simulations to calculate the aerodynamic characteristics of 2-D NACA-4312 airfoil at different angles of attack (α) at fixed Reynolds number (Re), equal to 5×10^5 . These simulations were solved using two different turbulence models, one was the Standard k-ε model with enhanced wall treatment and other was the SST k-ω model. Numerical results demonstrate that both models can produce similar results with little deviations. It was observed that both lift and drag coefficient increase at higher angles of attack, however lift coefficient starts to reduce at α =13° which is known as stalling condition. Numerical results also show that flow separations start at rare edge when the angle of attack is higher than 13° due to the reduction of lift coefficient.

Effects of wavelength and amplitude of a wavy cylinder in cross-flow at low Reynolds numbers

2009 ◽  
Vol 620 ◽  
pp. 195-220 ◽  
Author(s):  
K. LAM ◽  
Y. F. LIN
Keyword(s):  
Reynolds Number ◽  
Laminar Flow ◽  
Circular Cylinder ◽  
Drag Coefficient ◽  
Shear Layer ◽  
Lift Coefficient ◽  
Three Dimensional ◽  
Spanwise Direction ◽  
Free Shear Layer ◽  
The Mean

Three-dimensional numerical simulations of laminar flow around a circular cylinder with sinusoidal variation of cross-section along the spanwise direction, named ‘wavy cylinder’, are performed. A series of wavy cylinders with different combinations of dimensionless wavelength (λ/Dm) and wave amplitude (a/Dm) are studied in detail at a Reynolds number of Re = U∞Dm/ν = 100, where U∞ is the free-stream velocity and Dm is the mean diameter of a wavy cylinder. The results of variation of mean drag coefficient and root mean square (r.m.s.) lift coefficient with dimensionless wavelength show that significant reduction of mean and fluctuating force coefficients occurs at optimal dimensionless wavelengths λ/Dm of around 2.5 and 6 respectively for the different amplitudes studied. Based on the variation of flow structures and force characteristics, the dimensionless wavelength from λ/Dm = 1 to λ/Dm = 10 is classified into three wavelength regimes corresponding to three types of wake structures. The wake structures at the near wake of different wavy cylinders are captured. For all wavy cylinders, the flow separation line varies along the spanwise direction. This leads to the development of a three-dimensional free shear layer with periodic repetition along the spanwise direction. The three-dimensional free shear layer of the wavy cylinder is larger and more stable than that of the circular cylinder, and in some cases the free shear layer even does not roll up into a mature vortex street behind the cylinder. As a result, the mean drag coefficients of some of the typical wavy cylinders are less than that of a corresponding circular cylinder with a maximum drag coefficient reduction up to 18%. The r.m.s. lift coefficients are greatly reduced to practically zero at optimal wavelengths. In the laminar flow regime (60 ≤ Re ≤ 150), the values of optimal wavelength are Reynolds number dependent.

Validation of Numerical Analysis to Estimate Airfoil Aerodynamic Characteristics at Low Reynolds Number Region

2015 ◽  
Author(s):  
Donghwi Lee ◽  
Taku Nonomura ◽  
Akira Oyama ◽  
Kozo Fujii
Keyword(s):  
Reynolds Number ◽  
Numerical Method ◽  
Low Reynolds Number ◽  
Lift Coefficient ◽  
Three Dimensional ◽  
Aerodynamic Characteristics ◽  
Navier Stokes ◽  
Two Dimensional ◽  
Eddy Simulation ◽  
Low Reynolds

In this study, two-dimensional laminar simulation (2-D Lam), two-dimensional Reynolds Averaged Navier-Stokes simulation with the Spalart-Allmaras turbulence model (2-D RANS(SA)), and implicit three-dimensional large-eddy simulation (3-D LES) are performed for NACA0012, NACA0006, and Ishii airfoils at Rec = 3.0 × 104. The relation between a predictability of airfoil aerodynamic characteristics and a dependence of airfoil geometry shape of each numerical method is evaluated at the low Reynolds number. Although little discrepancy is observed for the lift coefficient predictability, significant differences are presented in terms of the separation and reattachment points predictability depending on the numerical methods. The 2-D Lam simulation can predict the lift coefficients as well as the separation and reattachment points qualitatively as similar to the 3-D LES results except for the high angle of attack which is accompanied by the massive separation. The 2-D RANS(SA), the weak nonlinearity and stall phenomena for the lift coefficients are observed. A good predictability of the separation point are shown, however, it cannot be estimated the reattachment points due to the trend to predict widely for the separation region. The predictabilities of each numerical method appear regardless of the airfoil shapes.

scholarly journals Lift and Drag Coefficient Map of NACA4415 Airfoil

2021 ◽  
Vol 2076 (1) ◽  
pp. 012066
Author(s):  
Rui Yin ◽  
Jing Huang ◽  
Zhi-Yuan He
Keyword(s):  
Reynolds Number ◽  
Drag Coefficient ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Aerodynamic Characteristics ◽  
Optimal Angle ◽  
Fluent Software ◽  
Lift And Drag ◽  
Drag Ratio ◽  
Lift To Drag Ratio

Abstract The NACA4415 airfoil was numerically simulated with the help of the Fluent software to analyze its aerodynamic characteristics. Results are acquired as follows: The calculation accuracy of Fluent software is much higher than that of XFOIL software; the calculation result of SST k-ω(sstkw) turbulence model is closest to the experimental value; within a certain range, the larger the Reynolds number is, the larger the lift coefficient and lift-to-drag ratio of the airfoil will be, and the smaller the drag coefficient will be; when the angle of attack is less than the optimal angle of attack, the Reynolds number has less influence on the lift-to-drag coefficient and the lift-to-drag ratio; as the Reynolds number increases, the optimal angle of attack increases slightly, and the applicable angle of attack range for high lift-to-drag ratios becomes smaller.

scholarly journals Effect of the Reynolds Number and Clearance Flow on the Aerodynamic Characteristics of a New Variable Inlet Guide Vane

Aerospace ◽  
2021 ◽  
Vol 8 (7) ◽  
pp. 172
Author(s):  
Hengtao Shi
Keyword(s):  
Reynolds Number ◽  
Guide Vane ◽  
Three Dimensional ◽  
High Growth ◽  
Aerodynamic Characteristics ◽  
Inlet Guide Vane ◽  
Separation Region ◽  
Clearance Flow ◽  
New Type ◽  
Variable Inlet Guide Vane

Recently, a new type of low-loss variable inlet guide vane (VIGV) was proposed for improving a compressor’s performance under off-design conditions. To provide more information for applications, this work investigated the effect of the Reynolds number and clearance flow on the aerodynamic characteristics of this new type of VIGV. The performance and flow field of two representative airfoils with different chord Reynolds numbers were studied with the widely used commercial software ANSYS CFX after validation was completed. Calculations indicate that, with the decrease in the Reynolds number Rec, the airfoil loss coefficient ω and deviation δ first increase slightly and then entered a high growth rate in a low range of Rec. Afterwards, a detailed boundary-layer analysis was conducted to reveal the flow mechanism for the airfoil performance degradation with a low Reynolds number. For the design point, it is the appearance and extension of the separation region on the rear portion; for the maximum incidence point, it is the increase in the length and height of the separation region on the former portion. The three-dimensional VIGV research confirms the Reynolds number effect on airfoils. Furthermore, the clearance leakage flow forms a strong stream-wise vortex by injection into the mainflow, resulting in a high total-pressure loss and under-turning in the endwall region, which shows the potential benefits of seal treatment.

Dynamic Stall Simulation of Flow Over NACA0012 Airfoil at 1 Million Reynolds Number

2015 ◽  
Author(s):  
Venkata Ravishankar Kasibhotla ◽  
Danesh Tafti
Keyword(s):  
Reynolds Number ◽  
Flow Field ◽  
Lift Coefficient ◽  
Three Dimensional ◽  
Dynamic Stall ◽  
Sharp Drop ◽  
Airfoil Surface ◽  
Naca0012 Airfoil ◽  
Reduced Frequency ◽  
Edge Vortex

The paper is concerned with the prediction and analysis of dynamic stall of flow past a pitching NACA0012 airfoil at 1 million Reynolds number based on the chord length of the airfoil and at reduced frequency of 0.25 in a three dimensional flow field. The turbulence in the flow field is resolved using large eddy simulations with the dynamic Smagorinsky model at the sub grid scale. The development of dynamic stall vortex, shedding and reattachment as predicted by the present study are discussed in detail. This study has shown that the downstroke phase of the pitching motion is strongly three dimensional and is highly complex, whereas the flow is practically two dimensional during the upstroke. The lift coefficient agrees well with the measurements during the upstroke. However, there are differences during the downstroke. The computed lift coefficient undergoes a sharp drop during the start of the downstroke as the convected leading edge vortex moves away from the airfoil surface. This is followed by a recovery of the lift coefficient with the formation of a secondary trailing edge vortex. While these dynamics are clearly reflected in the predicted lift coefficient, the experimental evolution of lift during the downstroke maintains a fairly smooth and monotonic decrease in the lift coefficient with no lift recovery. The simulations also show that the reattachment process of the stalled airfoil is completed before the start of the upstroke in the subsequent cycle due to the high reduced frequency of the pitching cycle.

Performance Estimation of Axial Flow Turbines

1970 ◽  
Vol 185 (1) ◽  
pp. 407-424 ◽  
Author(s):  
H. R. M. Craig ◽  
H. J. A. Cox
Keyword(s):  
Reynolds Number ◽  
Aspect Ratio ◽  
Gas Turbines ◽  
Three Dimensional ◽  
Axial Flow ◽  
Performance Estimation ◽  
Speed Ratio ◽  
Test Results ◽  
Wide Range ◽  
Relevant Variables

A comprehensive method of estimating the performance of axial flow steam and gas turbines is presented, based on analysis of linear cascade tests on blading, on a number of turbine test results, and on air tests of model casings. The validity of the use of such data is briefly considered. Data are presented to allow performance estimation of actual machines over a wide range of Reynolds number, Mach number, aspect ratio and other relevant variables. The use of the method in connection with three-dimensional methods of flow estimation is considered, and data presented showing encouraging agreement between estimates and available test results. Finally ‘carpets’ are presented showing the trends in efficiencies that are attainable in turbines designed over a wide range of loading, axial velocity/blade speed ratio, Reynolds number and aspect ratio.

A Simple and Robust Subsonic Boundary Layer Method to Be Used with the Panel Method for Wing Calculations Using a Wing Strip Approach

2015 ◽  
Vol 798 ◽  
pp. 596-601
Author(s):  
R.F. Francisco Reis ◽  
Guilherme A. Santana ◽  
Paulo Iscold ◽  
Carlos A. Cimini
Keyword(s):  
Boundary Layer ◽  
Lift Coefficient ◽  
Aircraft Design ◽  
Aerodynamic Characteristics ◽  
Viscous Drag ◽  
Layer Method ◽  
Boundary Layer Method ◽  
Dimensional Boundary ◽  
Classical Integral ◽  
Empirical Corrections

This paper will present the development of a simple subsonic boundary layer method suitable to be used coupled with panel methods in order to estimate the aerodynamic characteristics, including viscous drag and maximum lift coefficient, of 3D wings. The proposed method does not require viscous-inviscid iterations and is based on classical integral bi-dimensional boundary layer theory using Thwaites and Head ́s models with bi-dimensional empirical corrections applied to each wing strip being therefor robust and efficient to be used in the early conceptual stage of aircraft design. Presented results are compared to the Modified CS Method in an IBL scheme and experimental data and are shown to provide good results.

scholarly journals Aerodynamic and Vibration Characteristics of the Micro-Octocopter at Low Reynolds Number

2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Xiaohua Zou ◽  
Mingsheng Ling ◽  
Wenzheng Zhai
Keyword(s):  
Reynolds Number ◽  
Load Capacity ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Aerodynamic Characteristics ◽  
Vibration Characteristics ◽  
Low Reynolds ◽  
Vibration Performance ◽  
Drag Ratio ◽  
Lift To Drag Ratio

With the development of flight technology, the need for stable aerodynamic and vibration performance of the aircraft in the civil and military fields has gradually increased. In this case, the requirements for aerodynamic and vibration characteristics of the aircraft have also been strengthened. The existing four-rotor aircraft carries limited airborne equipment and payload, while the current eight-rotor aircraft adopts a plane layout. The size of the propeller is generally fixed, including the load capacity. The upper and lower tower layout analyzed in this paper can effectively solve the problems of insufficient four-axis load and unstable aerodynamic and vibration performance of the existing eight-axis aircraft. This paper takes the miniature octorotor as the research object and studies the aerodynamic characteristics of the miniature octorotor at different low Reynolds numbers, different air pressures and thicknesses, and the lift coefficient and lift-to-drag ratio, as well as the vibration under different elastic moduli and air pressure characteristics. The research algorithm adopted in this paper is the numerical method of fluid-solid cohesion and the control equation of flow field analysis. The research results show that, with the increase in the Reynolds number within a certain range, the aerodynamic characteristics of the miniature octorotor gradually become better. When the elastic modulus is 2.5 E, the aircraft’s specific performance is that the lift increases, the critical angle of attack increases, the drag decreases, the lift-to-drag ratio increases significantly, and the angle of attack decreases. However, the transition position of the flow around the airfoil surface is getting closer to the leading edge, and its state is more likely to transition from laminar flow to turbulent flow. When the unidirectional carbon fiber-reinforced thickness is 0.2 mm and the thin arc-shaped airfoil with the convex structure has a uniform thickness of 2.5% and a uniform curvature of 4.5%, the aerodynamic and vibration characteristics of the octorotor aircraft are most beneficial to flight.

Sign in / Sign up

Export Citation Format

Share Document