scholarly journals Analysis of Bifurcations in Multiharmonic Analysis of Nonlinear Forced Vibrations of Gas Turbine Engine Structures With Friction and Gaps

2016 ◽  
Vol 138 (10) ◽  
Author(s):  
E. P. Petrov
Keyword(s):  
Gas Turbine ◽  
Large Scale ◽  
Parameter Variation ◽  
Forced Vibrations ◽  
Forced Response ◽  
Operating Conditions ◽  
Frequency Domain Method ◽  
Cubic Nonlinearity ◽  
Turbine Engine ◽  
Detection And Localization

An efficient frequency-domain method has been developed to analyze the forced response of large-scale nonlinear gas turbine structures with bifurcations. The method allows detection and localization of the design and operating conditions sets where bifurcations occur, calculation of tangents to the solution trajectory, and continuation of solutions under parameter variation for structures with bifurcations. The method is aimed at calculation of steady-state periodic solution, and multiharmonic representation of the variation of displacements in time is used. The possibility of bifurcations in realistic gas-turbine structures with friction contacts and with cubic nonlinearity has been shown.

scholarly journals Analysis of Bifurcations in Multiharmonic Analysis of Nonlinear Forced Vibrations of Gas-Turbine Engine Structures With Friction and Gaps

2015 ◽  
Author(s):  
E. P. Petrov
Keyword(s):  
Gas Turbine ◽  
Large Scale ◽  
Parameter Variation ◽  
Forced Vibrations ◽  
Forced Response ◽  
Operating Conditions ◽  
Frequency Domain Method ◽  
Cubic Nonlinearity ◽  
Turbine Engine ◽  
Detection And Localization

An efficient frequency-domain method has been developed to analyse the forced response of large-scale nonlinear gas-turbine structures with bifurcations. The method allows: detection and localization of the design and operating conditions sets where bifurcations occur; calculation of tangents to the solution trajectory and continuation of solutions under parameter variation for structures with bifurcations. The method is aimed at calculation of steady-state periodic solution and multiharmonic representation of the variation of displacements in time is used. The possibility of bifurcations in realistic gas-turbine structures with friction contacts and with cubic nonlinearity has been shown.

scholarly journals Stability Analysis of Multiharmonic Nonlinear Vibrations for Large Models of Gas-Turbine Engine Structures With Friction and Gaps

2016 ◽  
Author(s):  
E. P. Petrov
Keyword(s):  
Gas Turbine ◽  
Large Scale ◽  
Frequency Domain Analysis ◽  
Gas Turbine Engine ◽  
Forced Response ◽  
Scale Model ◽  
Turbine Engine ◽  
Nonlinear Springs ◽  
Large Scale Model ◽  
The Stability

An efficient method is proposed for the multiharmonic frequency domain analysis of the stability for nonlinear periodic forced vibrations in gas-turbine engine structures and turbomachines with friction, gaps and other types of nonlinear contact interfaces. The method allows using large-scale finite element models for structural components together with detailed description of nonlinear interactions at contact interfaces between these components. The highly accurate reduced models are applied in the assessment of stability of periodic regimes for large-scale model of gas-turbine structures. An approach is proposed for the highly-accurate calculation of motion of a structure after it is perturbed from the periodic nonlinear forced response. Efficiency of the developed approach is demonstrated on a set of test cases including simple models and large-scale realistic bladed disc models with different types of nonlinearities: friction, gaps and cubic nonlinear springs.

scholarly journals Stability Analysis of Multiharmonic Nonlinear Vibrations for Large Models of Gas Turbine Engine Structures With Friction and Gaps

2016 ◽  
Vol 139 (2) ◽  
Author(s):  
E. P. Petrov
Keyword(s):  
Gas Turbine ◽  
Large Scale ◽  
Frequency Domain Analysis ◽  
Gas Turbine Engine ◽  
Forced Response ◽  
Scale Model ◽  
Turbine Engine ◽  
Nonlinear Springs ◽  
Large Scale Model ◽  
The Stability

An efficient method is proposed for the multiharmonic frequency-domain analysis of the stability for nonlinear periodic forced vibrations in gas turbine engine structures and turbomachines with friction, gaps, and other types of nonlinear contact interfaces. The method allows using large-scale finite element models for structural components together with detailed description of nonlinear interactions at contact interfaces between these components. The highly accurate reduced models are applied in the assessment of stability of periodic regimes for large-scale model of gas turbine structures. An approach is proposed for the highly accurate calculation of motion of a structure after it is perturbed from the periodic nonlinear forced response. Efficiency of the developed approach is demonstrated on a set of test cases including simple models and large-scale realistic bladed disk models with different types of nonlinearities: friction, gaps, and cubic nonlinear springs.

Design and Analysis of an Intentional Mistuning Experiment Reducing Flutter Susceptibility and Minimizing Forced Response of a Jet Engine Fan

2017 ◽  
Author(s):  
Felix Figaschewsky ◽  
Arnold Kühhorn ◽  
Bernd Beirow ◽  
Jens Nipkau ◽  
Thomas Giersch ◽  
...  
Keyword(s):  
Computational Model ◽  
Paint Layer ◽  
Forced Vibrations ◽  
Forced Response ◽  
Operating Conditions ◽  
Jet Engines ◽  
Jet Engine ◽  
Aspect Ratios ◽  
Engine Order ◽  
Stall Flutter

Recent demands for a reduction of specific fuel consumption of jet engines have been opposed by increasing propulsive efficiency with higher bypass ratios and increased engine sizes. At the same time the challenge for the engine development is to design safe and efficient fan blades of high aspect ratios. Since the fan is the very first rotor stage, it experiences significant distortions in the incoming flow depending on the operating conditions. Flow distortions do not only lead to a performance and stall margin loss but also to remarkable low engine order (LEO) excitation responsible for forced vibrations of fundamental modes. Additionally, fans of jet engines typically suffer from stall flutter, which can be additionally amplified by reflections of acoustic pressure waves at the intake. Stall flutter appears before approaching the stall line on the fan’s characteristic and limits its stable operating range. Despite the fact that this “flutter bite” usually affects only a very narrow speed range, it reduces the overall margin of safe operation significantly. With increasing aspect ratios of ultra-high bypass ratio jet engines the flutter susceptibility will probably increase further and emphasizes the importance of considering aeromechanical analyses early in the design phase of future fans. This paper aims at proving that intentional mistuning is able to remove the flutter bite of modern jet engine fans without raising issues due to heavily increased forced vibrations induced by LEO excitation. Whereas intentional mistuning is an established technology in mitigating flutter, it is also known to amplify the forced response. However, recent investigations considering aeroelastic coupling revealed that under specific circumstances mistuning can also reduce the forced response due to engine order excitation. In order to allow a direct comparison and to limit costs as well as effort at the same time, the intentional mistuning is introduced in a non-destructive way by applying heavy paint to the blades. Its impact on the blade’s natural frequencies is estimated via finite element models with an additional paint layer. In parallel, this procedure is experimentally verified with painted fan blades in the laboratory. A validated SNM (subset of nominal system modes) representation of the fan is used as a computational model to characterize its mistuned vibration behavior. Its validation is done by comparing mistuned mode shape envelopes and frequencies of an experimental modal analysis at rest with those obtained by the updated computational model. In order to find a mistuning pattern minimizing the forced response of mode 1 and 2 at the same time and satisfying stability and imbalance constraints, a multi-objective optimization has been carried out. Finally, the beneficial properties of the optimized mistuning pattern are verified in a rig test of the painted rotor.

Evaluation of Fuel Preparation Systems for Lean Premixing-Prevaporizing Combustors

1986 ◽  
Vol 108 (2) ◽  
pp. 391-395
Author(s):  
W. J. Dodds ◽  
E. E. Ekstedt
Keyword(s):  
System Design ◽  
Large Scale ◽  
Fuel Injection ◽  
Operating Conditions ◽  
Turbine Engine ◽  
Fuel Injectors ◽  
Design Concepts ◽  
Mixture Preparation ◽  
Design Variables ◽  
System Length

A series of tests was conducted to provide data for the design of premixing-prevaporizing fuel-air mixture preparation systems for aircraft gas turbine engine combustors. Fifteen configurations of four different fuel-air mixture preparation system design concepts were evaluated to determine fuel-air mixture uniformity at the system exit over a range of conditions representative of cruise operation for a modern commercial turbofan engine. Operating conditions, including pressure, temperature, fuel-air ratio, and velocity had no clear effect on mixture uniformity in systems which used low-pressure fuel injectors. However, performance of systems using pressure atomizing fuel nozzles and large-scale mixing devices was shown to be sensitive to operating conditions. Variations in system design variables were also evaluated and correlated. Mixture uniformity improved with increased system length, pressure drop, and number of fuel injection points per unit area. A premixing system compatible with the combustor envelope of a typical combustion system and capable of providing mixture nonuniformity (standard deviation/mean) below 15% over a typical range of cruise operating conditions was demonstrated.

Optimal State-Space Control of a Gas Turbine Engine

1992 ◽  
Vol 114 (4) ◽  
pp. 763-767 ◽  
Author(s):  
J. W. Watts ◽  
T. E. Dwan ◽  
C. G. Brockus
Keyword(s):  
State Space ◽  
Gas Turbine ◽  
State Space Model ◽  
Gas Turbine Engine ◽  
The State ◽  
Operating Conditions ◽  
Turbine Engine ◽  
Analog Control ◽  
Linear State ◽  
High Level

An analog fuel control for a gas turbine engine was compared with several state-space derived fuel controls. A single-spool, simple cycle gas turbine engine was modeled using ACSL (high level simulation language based on FORTRAN). The model included an analog fuel control representative of existing commercial fuel controls. The ACSL model was stripped of nonessential states to produce an eight-state linear state-space model of the engine. The A, B, and C matrices, derived from rated operating conditions, were used to obtain feedback control gains by the following methods: (1) state feedback; (2) LQR theory; (3) Bellman method; and (4) polygonal search. An off-load transient followed by an on-load transient was run for each of these fuel controls. The transient curves obtained were used to compare the state-space fuel controls with the analog fuel control. The state-space fuel controls did better than the analog control.

The Effect of Heat Transfer Coefficient Increase on Tip Clearance Control in H.P. Compressors in Gas Turbine Engine

2013 ◽  
Author(s):  
Godwin Ita Ekong ◽  
Christopher A. Long ◽  
Peter R. N. Childs
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Gas Turbine ◽  
Time Constant ◽  
Gas Turbine Engine ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Test Facility ◽  
Turbine Engine

Compressor tip clearance for a gas turbine engine application is the radial gap between the stationary compressor casing and the rotating blades. The gap varies significantly during different operating conditions of the engine due to centrifugal forces on the rotor and differential thermal expansions in the discs and casing. The tip clearance in the axial flow compressor of modern commercial civil aero-engines is of significance in terms of both mechanical integrity and performance. In general, the clearance is of critical importance to civil airline operators and their customers alike because as the clearance between the compressor blade tips and the casing increases, the aerodynamic efficiency will decrease and therefore the specific fuel consumption and operating costs will increase. This paper reports on the development of a range of concepts and their evaluation for the reduction and control of tip clearance in H.P. compressors using an enhanced heat transfer coefficient approach. This would lead to improvement in cruise tip clearances. A test facility has been developed for the study at the University of Sussex, incorporating a rotor and an inner shaft scaled down from a Rolls-Royce Trent aero-engine to a ratio of 0.7:1 with a rotational speed of up to 10000 rpm. The idle and maximum take-off conditions in the square cycle correspond to in-cavity rotational Reynolds numbers of 3.1×106 ≤ Reφ ≤ 1.0×107. The project involved modelling of the experimental facilities, to demonstrate proof of concept. The analysis shows that increasing the thermal response of the high pressure compressor (HPC) drum of a gas turbine engine assembly will reduce the drum time constant, thereby reducing the re-slam characteristics of the drum causing a reduction in the cold build clearance (CBC), and hence the reduction in cruise clearance. A further reduction can be achieved by introducing radial inflow into the drum cavity to further increase the disc heat transfer coefficient in the cavity; hence a further reduction in disc drum time constant.

scholarly journals Comprehensive report on Materials for Gas Turbine Engine Components

2019 ◽  
Vol 9 (2S2) ◽  
pp. 155-158
Keyword(s):  
Gas Turbine ◽  
Turbine Blade ◽  
Thermal Stresses ◽  
Prolonged Exposure ◽  
Raw Materials ◽  
Turbine Blades ◽  
Gas Turbine Engine ◽  
Operating Conditions ◽  
Turbine Engine ◽  
Engine Component

In the past three decades, it is very challenging for the researchers to design and development a best gas turbine engine component. Engine component has to face different operating conditions at different working environments. Nickel based superalloys are the best material to design turbine components. Inconel 718, Inconel 617, Hastelloy, Monel and Udimet are the common material used for turbine components. Directional solidification is one of the conventional casting routes followed to develop turbine blades. It is also reported that the raw materials are heat treated / age hardened to enrich the desired properties of the material implementation. Accordingly they are highly susceptible to mechanical and thermal stresses while operating. The hot section of the turbine components will experience repeated thermal stress. The halides in the combination of sulfur, chlorides and vanadate are deposited as molten salt on the surface of the turbine blade. On prolonged exposure the surface of the turbine blade starts to peel as an oxide scale. Microscopic images are the supportive results to compare the surface morphology after complete oxidation / corrosion studies. The spectroscopic results are useful to identify the elemental analysis over oxides formed. The predominant oxides observed are NiO, Cr2O3, Fe2O3 and NiCr2O4. These oxides are vulnerable on prolonged exposure and according to PB ratio the passivation are very less. In recent research, the invention on nickel based superalloys turbine blades produced through other advanced manufacturing process is also compared. A summary was made through comparing the conventional material and advanced materials performance of turbine blade material for high temperature performance.

Method for calculating the thrust and specific thrust of a double-flow gas turbine engine based on the results of tests at the laboratory unit «Flame»

2021 ◽  
pp. 58-64
Author(s):  
S.M. Sergeev ◽  
◽  
V.A. Kudriashov ◽  
N.V. Petrukhin ◽  
◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbine Engine ◽  
Operating Conditions ◽  
Similarity Criteria ◽  
Fuel Quality ◽  
Jet Engines ◽  
Laboratory Unit ◽  
Turbine Engine ◽  
Specific Thrust ◽  
The Cost

The main technical characteristics of jet engines depend on the fuel quality: thrust and fuel consumption. As a rule, the comparative assessment of real engines is carried by specific values. Specific thrust is one of the most important parameters of the gas turbine engine (GTE). The larger it is, the smaller the required air flow rate through the engine at a given thrust and therefore its dimensions and mass. To date, a system for evaluating the performance properties of fuels based on qualification methods has been created. However, these methods do not allow calculating the thrust and specific thrust of the engine and potentially assessing the effect of fuels on these characteristics. Therefore, the issues of efficient use of fuels for GTE are solved almost exclusively on the basis of tests at testing units with full-scale engines, which are carried out repeatedly, which leads to a significant increase in the cost of testing. The article proposes a method for calculating the thrust and specific thrust of a double-flow gas turbine engine according to the results of tests at a constant volume laboratory unit of bypass type “Flame”. The method is based on modeling the engine operating conditions using the similarity criteria of the bench reactor and the real engine and allows reducing significantly the material and time costs for testing. The experimental of the combustion characteristics of hydrocarbon fuels and the rated values of their thrust and specific thrust for a double-flow gas turbine engine are presented.

scholarly journals Investigation of Micro Gas Turbine Systems for High Speed Long Loiter Tactical Unmanned Air Systems

Aerospace ◽  
2019 ◽  
Vol 6 (5) ◽  
pp. 55 ◽  
Author(s):  
James Large ◽  
Apostolos Pesyridis
Keyword(s):  
Gas Turbine ◽  
Fuel Consumption ◽  
High Speed ◽  
Engine Performance ◽  
Operating Conditions ◽  
Turbine Engine ◽  
Micro Gas Turbine ◽  
Fan Speed ◽  
Relative Design ◽  
Design Simplicity

In this study, the on-going research into the improvement of micro-gas turbine propulsion system performance and the suitability for its application as propulsion systems for small tactical UAVs (<600 kg) is investigated. The study is focused around the concept of converting existing micro turbojet engines into turbofans with the use of a continuously variable gearbox, thus maintaining a single spool configuration and relative design simplicity. This is an effort to reduce the initial engine development cost, whilst improving the propulsive performance. The BMT 120 KS micro turbojet engine is selected for the performance evaluation of the conversion process using the gas turbine performance software GasTurb13. The preliminary design of a matched low-pressure compressor (LPC) for the proposed engine is then performed using meanline calculation methods. According to the analysis that is carried out, an improvement in the converted micro gas turbine engine performance, in terms of thrust and specific fuel consumption is achieved. Furthermore, with the introduction of a CVT gearbox, the fan speed operation may be adjusted independently of the core, allowing an increased thrust generation or better fuel consumption. This therefore enables a wider gamut of operating conditions and enhances the performance and scope of the tactical UAV.

Sign in / Sign up

Export Citation Format

Share Document