scholarly journals Numerical Simulation of Stall Inception Mechanisms in a Centrifugal Compressor With Vaned Diffuser

2016 ◽  
Vol 138 (12) ◽  
Author(s):  
Y. Bousquet ◽  
N. Binder ◽  
G. Dufour ◽  
X. Carbonneau ◽  
M. Roumeas ◽  
...  
Keyword(s):  
Mass Flow ◽  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Suction Side ◽  
Boundary Layer Separation ◽  
Flow Topology ◽  
Vaned Diffuser ◽  
Stall Inception ◽  
Flow Reduction

The present paper numerically investigates the stall inception mechanisms in a centrifugal compressor stage composed of a splittered unshrouded impeller and a vaned diffuser. Unsteady numerical simulations have been conducted on a calculation domain comprising all the blade passages over 360 deg for the impeller and the diffuser. Three stable operating points are simulated along a speed line, and the full path to instability is investigated. The paper focusses first on the effects of the mass flow reduction on the flow topology at the inlet of both components. Then, a detailed analysis of stall inception mechanisms is proposed. It is shown that at the inlet of both components, the mass flow reduction induces boundary layer separation on the blade suction side, which results in a vortex tube having its upper end at the casing and its lower end at the blade wall. Some similarities with flows in axial compressor operating at stall condition are outlined. The stall inception process starts with the growth of the amplitude of a modal wave rotating in the vaneless space. As the flow in the compressor is subsonic, the wave propagates upstream and interacts with the impeller flow structure. This interaction leads to the drop in the impeller pressure ratio.

scholarly journals Analysis of the Unsteady Flow Field in a Centrifugal Compressor from Peak Efficiency to Near Stall with Full-Annulus Simulations

2014 ◽  
Vol 2014 ◽  
pp. 1-11 ◽  
Author(s):  
Yannick Bousquet ◽  
Xavier Carbonneau ◽  
Guillaume Dufour ◽  
Nicolas Binder ◽  
Isabelle Trebinjac
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
Mass Flow ◽  
Centrifugal Compressor ◽  
Incidence Angle ◽  
Pressure Ratio ◽  
Suction Side ◽  
Operating Point ◽  
Peak Efficiency ◽  
Vaned Diffuser

This study concerns a 2.5 pressure ratio centrifugal compressor stage consisting of a splittered unshrouded impeller and a vaned diffuser. The aim of this paper is to investigate the modifications of the flow structure when the operating point moves from peak efficiency to near stall. The investigations are based on the results of unsteady three-dimensional simulations, in a calculation domain comprising all the blade. A detailed analysis is given in the impeller inducer and in the vaned diffuser entry region through time-averaged and unsteady flow field. In the impeller inducer, this study demonstrates that the mass flow reduction from peak efficiency to near stall leads to intensification of the secondary flow effects. The low momentum fluid accumulated near the shroud interacts with the main flow through a shear layer zone. At near stall condition, the interface between the two flow structures becomes unstable leading to vortices development. In the diffuser entry region, by reducing the mass flow, the high incidence angle from the impeller exit induces a separation on the diffuser vane suction side. At near stall operating point, vorticity from the separation is shed into vortex cores which are periodically formed and convected downstream along the suction side.

Effect of Unsteadiness on the Performance of a Transonic Centrifugal Compressor Stage

2009 ◽  
Vol 131 (4) ◽  
Author(s):  
Isabelle Trébinjac ◽  
Pascale Kulisa ◽  
Nicolas Bulot ◽  
Nicolas Rochuon
Keyword(s):  
Shock Wave ◽  
Mass Flow ◽  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Wake Flow ◽  
Experimental Investigations ◽  
Compressor Stage ◽  
Vaned Diffuser ◽  
Centrifugal Compressor Stage ◽  
Transonic Centrifugal Compressor

Numerical and experimental investigations were conducted in a transonic centrifugal compressor stage composed of a backswept splittered unshrouded impeller and a vaned diffuser. The characteristic curves of the compressor stage resulting from the unsteady simulations and the experiments show a good agreement over the whole operating range. On the contrary, the total pressure ratio resulting from the steady simulations is clearly overestimated. A detailed analysis of the flow field at design operating point led to identify the physical mechanisms involved in the blade row interaction that underlie the observed shift in performance. Attention was focused on the deformation in shape of the vane bow shock wave due its interaction with the jet and wake flow structure emerging from the impeller. An analytical model is proposed to quantify the time-averaged effects of the associated entropy increase. The model is based on the calculation of the losses across a shock wave at various inlet Mach numbers corresponding to the moving of the jet and wake flow in front of the shock wave. The model was applied to the compressor stage performance calculated with the steady simulations. The resulting curve of the overall pressure ratio as a function of the mass flow is clearly shifted toward the unsteady results. The model, in particular, enhances the prediction of the choked mass flow.

scholarly journals Performance Improvement of Axial Compressors and Fans with Plasma Actuation

2009 ◽  
Vol 2009 ◽  
pp. 1-13 ◽  
Author(s):  
Sebastien Lemire ◽  
Huu Duc Vo ◽  
Michael W. Benner
Keyword(s):  
Computational Study ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Suction Side ◽  
Boundary Layer Separation ◽  
Plasma Actuator ◽  
Control Device ◽  
Axial Compressors ◽  
Compressor Rotor ◽  
Flow Control Device

This paper proposes the use of plasma actuator to suppress boundary layer separation on a compressor blade suction side to increase axial compressor performance. Plasma actuators are a new type of electrical flow control device that imparts momentum to the air when submitted to a high AC voltage at high frequency. The concept presented in this paper consists in the positioning of a plasma actuator near the separation point on a compressor rotor suction side to increase flow turning. In this computational study, three parameters have been studied to evaluate the effectiveness of plasma actuator: actuator strength, position and actuation method (steady versus unsteady). Results show that plasma actuator operated in steady mode can increase the pressure ratio, efficiency, and power imparted by the rotor to the air and that the pressure ratio, efficiency and rotor power increase almost linearly with actuator strength. On the other hand, the actuator's position has limited effect on the performance increase. Finally, the results from unsteady simulations show a limited performance increase but are not fully conclusive, due possibly to the chosen pulsing frequencies of the actuator and/or to limitations of the CFD code.

Spike and Modal Stall Inception in an Advanced Turbocharger Centrifugal Compressor

2009 ◽  
Vol 131 (3) ◽  
Author(s):  
Z. S. Spakovszky ◽  
C. H. Roduner
Keyword(s):  
Centrifugal Compressor ◽  
High Speed ◽  
Pressure Ratio ◽  
Pressure Sensors ◽  
Rotating Stall ◽  
Vaned Diffuser ◽  
Stall Inception ◽  
Compression System ◽  
The Impact ◽  
Highly Loaded

In turbocharger applications, bleed air near the impeller exit is often used for secondary flow systems to seal bearing compartments and to balance the thrust load on the bearings. There is experimental evidence that the performance and operability of highly-loaded centrifugal compressor designs can be sensitive to the amount of bleed air. To investigate the underlying mechanisms and to assess the impact of bleed air on the compressor dynamic behavior, a research program was carried out on a preproduction, 5.0 pressure ratio, high-speed centrifugal compressor stage of advanced design. The investigations showed that bleed air can significantly reduce the stable flow range. Compressor rig experiments, using an array of unsteady pressure sensors and a bleed valve to simulate a typical turbocharger environment, suggest that the path into compression system instability is altered by the bleed flow. Without the bleed flow, the prestall behavior is dominated by short-wavelength disturbances, or so called “spikes,” in the vaneless space between the impeller and the vaned diffuser. Introducing bleed flow at the impeller exit reduces endwall blockage in the vaneless space and destabilizes the highly-loaded vaned diffuser. The impact is a 50% reduction in stable operating range. The altered diffuser characteristic reduces the compression system damping responsible for long-wavelength modal prestall behavior. A four-lobed backward traveling rotating stall wave is experimentally measured in agreement with calculations obtained from a previously developed dynamic compressor model. In addition, a self-contained endwall blockage control strategy was employed, successfully recovering 75% of the loss in surge-margin due to the bleed flow and yielding a one point increase in adiabatic compressor efficiency.

Effect of Unsteadiness on the Performance of a Transonic Centrifugal Compressor Stage

2008 ◽  
Author(s):  
Isabelle Tre´binjac ◽  
Pascale Kulisa ◽  
Nicolas Bulot ◽  
Nicolas Rochuon
Keyword(s):  
Shock Wave ◽  
Mass Flow ◽  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Wake Flow ◽  
Experimental Investigations ◽  
Compressor Stage ◽  
Vaned Diffuser ◽  
Centrifugal Compressor Stage ◽  
Transonic Centrifugal Compressor

Numerical and experimental investigations were conducted in a transonic centrifugal compressor stage composed of a backswept splittered unshrouded impeller and a vaned diffuser. The characteristic curves of the compressor stage resulting from the unsteady simulations and the experiments show a good agreement over the whole operating range. On the contrary, the total pressure ratio resulting from the steady simulations is clearly overestimated. A detailed analysis of the flow field at design operating point led to identify the physical mechanisms involved in the blade row interaction that underlie the observed shift in performance. Attention was focused on the deformation in shape of the vane bow shock wave due its interaction with the jet and wake flow structure emerging from the impeller. An analytical model is proposed to quantify the time-averaged effects of the associated entropy increase. The model is based on the calculation of the losses across a shock wave at various inlet Mach numbers corresponding to the moving of the jet and wake flow in front of the shock wave. The model was applied to the compressor stage performance calculated with the steady simulations. The resulting curve of the overall pressure ratio as a function of the mass flow is clearly shifted towards the unsteady results. The model in particular enhances the prediction of the choked mass flow.

An Investigation of Centrifugal Compressor Stability Enhancement Using a Novel Vaned Diffuser Recirculation Technique

2018 ◽  
Vol 140 (12) ◽  
Author(s):  
Lee Galloway ◽  
Daniel Rusch ◽  
Stephen Spence ◽  
Klemens Vogel ◽  
René Hunziker ◽  
...  
Keyword(s):  
Mass Flow ◽  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Vaned Diffuser ◽  
Casing Treatment ◽  
Operating Range ◽  
Stable Operating ◽  
Mass Flow Rates ◽  
Low Mass ◽  
Casing Treatments

The main centrifugal compressor performance criteria are pressure ratio, efficiency, and wide flow range. The relative importance of these criteria, and therefore the optimum design balance, varies between different applications. Vaned diffusers are generally used for high-performance applications as they can achieve higher efficiencies and pressure ratios, but have a reduced operating range, in comparison to vaneless diffusers. Many impeller-based casing treatments have been developed to enlarge the operating range of centrifugal compressors over the last decades but there is much less information available in open literature for diffuser focused methods, and they are not widely adopted in commercial compressor stages. The development of aerodynamic instabilities at low mass flow rate operating conditions can lead to the onset of rotating stall or surge, limiting the stable operating range of the centrifugal compressor stage. More understanding of these aerodynamic instabilities has been established in recent years. Based on this additional knowledge, new casing treatments can be developed to prevent or suppress the development of these instabilities, thus increasing the compressor stability at low mass flow rates. This paper presents a novel vaned diffuser casing treatment that successfully increased the stable operating range at low mass flow rates and high pressure ratios. Detailed experimental measurements from a high pressure ratio turbocharger compressor stage combined with complementary CFD simulations were used to examine the effect of the new diffuser casing treatment on the compressor flow field and led to the improvement in overall compressor stability. A detailed description of how the new casing treatment operates is presented within the paper.

Spike and Modal Stall Inception in an Advanced Turbocharger Centrifugal Compressor

2007 ◽  
Author(s):  
Z. S. Spakovszky ◽  
C. H. Roduner
Keyword(s):  
Centrifugal Compressor ◽  
High Speed ◽  
Pressure Ratio ◽  
Pressure Sensors ◽  
Rotating Stall ◽  
Vaned Diffuser ◽  
Stall Inception ◽  
Compression System ◽  
The Impact ◽  
Highly Loaded

In turbocharger applications bleed air near the impeller exit is often used for secondary flow systems to seal bearing compartments and to balance the thrust load on the bearings. There is experimental evidence that the performance and operability of highly loaded centrifugal compressor designs can be sensitive to the amount of bleed air. To investigate the underlying mechanisms and to assess the impact of bleed air on the compressor dynamic behavior, a research program was carried out on a pre-production, 5.0 pressure ratio, high-speed centrifugal compressor stage of advanced design. The investigations showed that bleed air can significantly reduce the stable flow range. Compressor rig experiments, using an array of unsteady pressure sensors and a bleed valve to simulate a typical turbocharger environment, suggest that the path into compression system instability is altered by the bleed flow. Without bleed flow, the pre-stall behavior is dominated by short wavelength disturbances, or so called ‘spikes’, in the vaneless space between the impeller and the vaned diffuser. Introducing bleed flow at impeller exit reduces endwall blockage in the vaneless space and destabilizes the highly-loaded vaned diffuser. The impact is a 50% reduction in stable operating range. The altered diffuser characteristic reduces the compression system damping responsible for long wavelength, modal pre-stall behavior. A four-lobed backward traveling rotating stall wave is experimentally measured, in agreement with calculations obtained from a previously developed dynamic compressor model. In addition, a self-contained, endwall blockage control strategy was employed, successfully recovering 75% of the loss in surge-margin due to bleed flow and yielding a 1 point increase in adiabiatic compressor efficiency.

Impact of Tip Clearance Size and Rotation Speed on the Surge Onset in a High Pressure Centrifugal Compressor

2012 ◽  
Author(s):  
Nicolas Buffaz ◽  
Isabelle Trébinjac
Keyword(s):  
Centrifugal Compressor ◽  
Rotation Speed ◽  
Pressure Sensors ◽  
Leading Edge ◽  
Suction Side ◽  
Boundary Layer Separation ◽  
Tip Clearance ◽  
Vaned Diffuser ◽  
The Impact ◽  
Blade Leading Edge

The results presented in the paper aim at investigating the impact of tip clearance size and rotation speed on the surge onset in a transonic single-stage centrifugal compressor composed of a backswept splittered unshrouded impeller and a vaned diffuser. For that purpose, various slow throttle ramps into surge were conducted from 100% to 60% design speed of the compressor and two different tip clearance heights were investigated. The 1MW LMFA-ECL test rig was used to carry out the tests in the compressor stage. Unsteady pressure measurements up to 150 KHz were carried out in the inducer (i.e. the entry zone of the impeller between the main blade leading edge and the splitter blade leading edge) and in the diffuser thanks to nine and fifteen static pressure sensors respectively. At cruise rotation speed (92.7% of the nominal rotation speed), the surge is triggered by a boundary layer separation on the diffuser vane suction side whatever the tip clearance height may be. No precursor of surge or pre-surge activity has been recorded in the diffuser or in the impeller. The surge reveals a spike-type inception and the tip clearance increase does not change the path into instability. At lower rotation speeds high frequency disturbances (nearly half the BPF) have been recorded in the inducer before surge. These disturbances can be understood as “tip clearance rotating disturbances” because they are generated at the leading edge of the main blades and move along the tip clearance trajectory. These disturbances reveal a very unstable behavior while the compressor runs into a stable operating point even if the flow at the tip of impeller is dramatically affected by these disturbances. But these disturbances do not trigger the surge which always originates in the diffuser.

An Experimental Investigation on the Clocking Effect Between Inlet Guide Vanes and Vaned Diffuser in a Centrifugal Compressor Stage

2008 ◽  
Author(s):  
Jiang Hua ◽  
Xi Guang ◽  
Zhang Wei ◽  
WuQi Gong ◽  
ZhiHeng Wang
Keyword(s):  
Experimental Investigation ◽  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Centrifugal Impeller ◽  
Vaned Diffuser ◽  
Guide Vanes ◽  
Inlet Guide Vanes ◽  
Stage Efficiency ◽  
Peak Value

Different circumferential angle positions between stator or rotor vane rows in turbomachinery can lead to different flow structures or stage performances. The clocking effect phenomenon has been detected in axial compressor and turbine by investigators, but rarely reported on centrifugal compressor. The present work is an experimental investigation on the stator clocking effect between inlet guide vanes (IGV) and vaned diffuser in a low-speed centrifugal compressor. The experimental rig consists of a circumferentially rotatable IGV, an unshrouded centrifugal impeller, a vaned diffuser, a volute and etc. The impeller diameter is 796mm, and the rotate speed is about 3100 rpm. At each inlet prewhirl angle of −20°, 0° and +20°, the stage performance curves are measured at three clocking angle positions of 0°, 8° and 16°. The result shows that at the circumferential angles of 0° and 8°, the efficiency curve has a double peak value feature, but at the angle of 16° being the conventional single peak value curve. Further, at the circumferential angles of 0° and 8°, the stage efficiency is bigger 3.6% than that case of the angle being 16°, where the IGV prewhirl angles are 0° and 20°. When the IGV prewhirl angle is changed into −20°, the stage efficiency increases about 2.0% near the first peak value position at the circumferential angles of 0°and 8° than at 16°, however, at the second peak value position, the stage efficiency at the circumferential angle of 0° is bigger about 1.4% than at 8° and 16°. Moreover, the circumferential angle positions between IGV and vaned diffuser have corresponding influence on the pressure ratio.

scholarly journals Axial Flow Compressor Stability Enhancement: Circumferential T-Shape Grooves Performance Investigation

Aerospace ◽  
2021 ◽  
Vol 8 (1) ◽  
pp. 12
Author(s):  
Marco Porro ◽  
Richard Jefferson-Loveday ◽  
Ernesto Benini
Keyword(s):  
Vortex Breakdown ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Suction Side ◽  
Treatment Technique ◽  
Tip Leakage Flow ◽  
Stall Inception ◽  
Stall Margin ◽  
Casing Treatment ◽  
Stall Margin Improvement

This work focuses its attention on possibilities to enhance the stability of an axial compressor using a casing treatment technique. Circumferential grooves machined into the case are considered and their performances evaluated using three-dimensional steady state computational simulations. The effects of rectangular and new T-shape grooves on NASA Rotor 37 performances are investigated, resolving in detail the flow field near the blade tip in order to understand the stall inception delay mechanism produced by the casing treatment. First, a validation of the computational model was carried out analysing a smooth wall case without grooves. The comparisons of the total pressure ratio, total temperature ratio and adiabatic efficiency profiles with experimental data highlighted the accuracy and validity of the model. Then, the results for a rectangular groove chosen as the baseline case demonstrated that the groove interacts with the tip leakage flow, weakening the vortex breakdown and reducing the separation at the blade suction side. These effects delay stall inception, improving compressor stability. New T-shape grooves were designed keeping the volume as a constant parameter and their performances were evaluated in terms of stall margin improvement and efficiency variation. All the configurations showed a common efficiency loss near the peak condition and some of them revealed a stall margin improvement with respect to the baseline. Due to their reduced depth, these new configurations are interesting because they enable the use of a thinner light-weight compressor case as is desirable in aerospace applications.

Sign in / Sign up

Export Citation Format

Share Document