An Investigation of the Stability Enhancement of a Centrifugal Compressor Stage Using a Porous Throat Diffuser

2017 ◽  
Vol 140 (1) ◽  
Author(s):  
Lee Galloway ◽  
Stephen Spence ◽  
Sung In Kim ◽  
Daniel Rusch ◽  
Klemens Vogel ◽  
...  
Keyword(s):  
Centrifugal Compressor ◽  
Compressor Stage ◽  
Vaned Diffuser ◽  
Flow Rates ◽  
Stall Inception ◽  
Centrifugal Compressor Stage ◽  
Operating Range ◽  
Stable Operating ◽  
The Stability ◽  
Circumferential Pressure

The stable operating range of a centrifugal compressor stage of an engine turbocharger is limited at low mass flow rates by aerodynamic instabilities which can lead to the onset of rotating stall or surge. There have been many techniques employed to increase the stable operating range of centrifugal compressor stages. The literature demonstrates that there are various possibilities for adding special treatments to the nominal diffuser vane geometry, or including injection or bleed flows to modify the diffuser flow field in order to influence diffuser stability. One such treatment is the porous throat diffuser (PTD). Although the benefits of this technique have been proven in the existing literature, a comprehensive understanding of how this technique operates is not yet available. This paper uses experimental measurements from a high pressure ratio (PR) compressor stage to acquire a sound understanding of the flow features within the vaned diffuser which affect the stability of the overall compression system and investigate the stabilizing mechanism of the porous throat diffuser. The nonuniform circumferential pressure imposed by the asymmetric volute is experimentally and numerically examined to understand if this provides a preferential location for stall inception in the diffuser. The following hypothesis is confirmed: linking of the diffuser throats via the side cavity equalizes the diffuser throat pressure, thus creating a more homogeneous circumferential pressure distribution, which delays stall inception to lower flow rates. The results of the porous throat diffuser configuration are compared to a standard vaned diffuser compressor stage in terms of overall compressor performance parameters, circumferential pressure nonuniformity at various locations through the compressor stage and diffuser subcomponent analysis. The diffuser inlet region was found to be the element most influenced by the porous throat diffuser, and the stability limit is mainly governed by this element.

An Investigation of the Stability Enhancement of a Centrifugal Compressor Stage Using a Porous Throat Diffuser

2017 ◽  
Author(s):  
Lee Galloway ◽  
Stephen Spence ◽  
Sung In Kim ◽  
Daniel Rusch ◽  
Klemens Vogel ◽  
...  
Keyword(s):  
Centrifugal Compressor ◽  
Compressor Stage ◽  
Vaned Diffuser ◽  
Flow Rates ◽  
Stall Inception ◽  
Centrifugal Compressor Stage ◽  
Operating Range ◽  
Stable Operating ◽  
The Stability ◽  
Circumferential Pressure

The stable operating range of a centrifugal compressor stage of an engine turbocharger is limited at low mass flow rates by aerodynamic instabilities which can lead to the onset of rotating stall or surge. There have been many techniques employed to increase the stable operating range of centrifugal compressor stages. The literature demonstrates that there are various possibilities for adding special treatments to the nominal diffuser vane geometry, or including injection or bleed flows to modify the diffuser flow field in order to influence diffuser stability. One such treatment is the porous throat diffuser. Although the benefits of this technique have been proven in the existing literature, a comprehensive understanding of how this technique operates is not yet available. This paper uses experimental measurements from a high pressure ratio compressor stage to acquire a sound understanding of the flow features within the vaned diffuser which affect the stability of the overall compression system and investigate the stabilising mechanism of the porous throat diffuser. The non-uniform circumferential pressure imposed by the asymmetric volute is experimentally and numerically examined to understand if this provides a preferential location for stall inception in the diffuser. The following hypothesis is confirmed: linking of the diffuser throats via the side cavity equalizes the diffuser throat pressure, thus creating a more homogeneous circumferential pressure distribution, which delays stall inception to lower flow rates. The results of the porous throat diffuser configuration are compared to a standard vaned diffuser compressor stage in terms of overall compressor performance parameters, circumferential pressure non-uniformity at various locations through the compressor stage and diffuser sub-component analysis. The diffuser inlet region was found to be the element most influenced by the porous throat diffuser and the stability limit is mainly governed by this element.

A centrifugal compressor stage with wide flow range vaned diffusers and different inlet configurations

2002 ◽  
Vol 216 (4) ◽  
pp. 307-320 ◽  
Author(s):  
Y Kim ◽  
A Engeda ◽  
R Aungier ◽  
N Amineni
Keyword(s):  
Centrifugal Compressor ◽  
Design Procedure ◽  
Substantial Improvement ◽  
Primary Objective ◽  
Compressor Stage ◽  
Vaned Diffuser ◽  
Centrifugal Compressor Stage ◽  
Stable Operating ◽  
Compressor Performance ◽  
Competitive Efficiency

In most cases, the diffuser system of a centrifugal compressor comes in the two general categories of a vaneless or a vaned diffuser. The vaned diffuser can generally be subdivided into two types depending on channel geometry (straight or curved channel) or depending on solidity. For the three different vaned diffusers of a centrifugal compressor stage, the design procedure is presented and experimental data are compared. The primary objective of the diffuser design was to achieve substantial improvement, compared with the stage currently used for the intended application, for the stable operating flow range as well as for the head rise from design to surge flow. The design goals also included achieving competitive efficiency levels, which required a significant efficiency improvement. Test results showed a much wider stable operating range than had been expected. This stage operated well beyond the expected vaned diffuser stall limit. The inlet configuration and inlet flow structure are known significantly to affect the compressor performance. Each of the three diffusers is tested for two different types of inlet configuration, and the relative performances are assessed.

scholarly journals Flow Studies in a Centrifugal Compressor Stage

2014 ◽  
Author(s):  
R. Rajendran
Keyword(s):  
Centrifugal Compressor ◽  
Flow Behavior ◽  
Compressor Stage ◽  
Impeller Blade ◽  
Vaned Diffuser ◽  
Flow Angle ◽  
Centrifugal Compressor Stage ◽  
Operating Range ◽  
Impeller Outlet ◽  
Outlet Flow

The overall efficiency of a compressor is dependent on the design of both the impeller and the diffuser. The vaned diffuser reduces the operating range compared to the vaneless diffuser. However, by proper setting of the diffuser with reference to the impeller, it is possible to achieve a good stage performance. This paper describes the experimental investigation of the detailed flow behavior inside a centrifugal compressor stage for three different setting angles of the vaned diffuser with reference to the fixed impeller blade outlet angle. It is seen that diffuser setting angles lower than the impeller outlet flow angle gives wide operating range.

scholarly journals Operating Range Extension of an Open Impeller Centrifugal Compressor Stage Utilising 3D Diffuser End Wall Contouring

2020 ◽  
Vol 5 (1) ◽  
pp. 4
Author(s):  
Daniel Hermann ◽  
Manfred Wirsum ◽  
Douglas Robinson ◽  
Philipp Jenny
Keyword(s):  
Centrifugal Compressor ◽  
Side Wall ◽  
Stability Limit ◽  
Scale Model ◽  
Compressor Stage ◽  
Vaned Diffuser ◽  
Efficient Operation ◽  
Baseline Design ◽  
Centrifugal Compressor Stage ◽  
Operating Range

State-of-the-art centrifugal compressor units utilised in pipeline and in energy storage applications face the challenge of flexible and highly efficient operation. Geometric contouring on the hub side near a vaned diffuser affects the flow in a way which increases operational flexibility by delaying the incipience of instability and thereby increases compressor operating range. In the present paper, a hub-side wall contouring is applied within the vaneless space and the vaned diffuser of an open impeller centrifugal compressor stage. The performance characteristic of the novel hub contouring is evaluated in a scale-model test rig and compared against a baseline design. A stable operating range increase of 8% is achieved for the contoured design at Mu 2 = 1.16. 5-hole probe measurements covering a complete diffuser blade-to-blade passage are performed upstream the diffuser and compared both against CFD simulations and against the measurements of the baseline design for an operating point near the stability limit.

Experimental Validation of a Wide-Range Centrifugal Compressor Stage for Supercritical CO2 Power Cycles

2019 ◽  
Vol 141 (6) ◽  
Author(s):  
Timothy C. Allison ◽  
Natalie R. Smith ◽  
Robert Pelton ◽  
Jason C. Wilkes ◽  
Sewoong Jung
Keyword(s):  
Centrifugal Compressor ◽  
Operating Conditions ◽  
Successful Implementation ◽  
Compressor Stage ◽  
Test Results ◽  
Power Cycles ◽  
Casing Treatment ◽  
Centrifugal Compressor Stage ◽  
Operating Range ◽  
Wide Range

Successful implementation of sCO2 power cycles requires high compressor efficiency at both the design-point and over a wide operating range in order to maximize cycle power output and maintain stable operation over a wide range of transient and part-load operating conditions. This requirement is particularly true for air-cooled cycles where compressor inlet density is a strong function of inlet temperature that is subject to daily and seasonal variations as well as transient events. In order to meet these requirements, a novel centrifugal compressor stage design was developed that incorporates multiple novel range extension features, including a passive recirculating casing treatment and semi-open impeller design. This design, presented and analyzed for CO2 operation in a previous paper, was fabricated via direct metal laser sintering and tested in an open-loop test rig in order to validate simulation results and the effectiveness of the casing treatment configuration. Predicted performance curves in air and CO2 conditions are compared, resulting in a reduced diffuser width requirement for the air test in order to match design velocities and demonstrate the casing treatment. Test results show that the casing treatment performance generally matched computational fluid dynamics (CFD) predictions, demonstrating an operating range of 69% and efficiency above air predictions across the entire map. The casing treatment configuration demonstrated improvements over the solid wall configuration in stage performance and flow characteristics at low flows, resulting in an effective 14% increase in operating range with a 0.5-point efficiency penalty. The test results are also compared to a traditional fully shrouded impeller with the same flow coefficient and similar head coefficient, showing a 42% range improvement over traditional designs.

Some Studies on Low Solidity Vaned Diffusers of a Centrifugal Compressor Stage

2005 ◽  
Author(s):  
T. Ch. Siva Reddy ◽  
G. V. Ramana Murty ◽  
Prasad Mukkavilli ◽  
D. N. Reddy
Keyword(s):  
Centrifugal Compressor ◽  
Static Pressure ◽  
Pressure Ratio ◽  
Pressure Recovery ◽  
Compressor Stage ◽  
Recovery Coefficient ◽  
Vaned Diffuser ◽  
Flow Angle ◽  
Centrifugal Compressor Stage ◽  
Pressure Recovery Coefficient

Numerical simulation of impeller and low solidity vaned diffuser (LSD) of a centrifugal compressor stage is performed individually using CFX- BladeGen and BladeGenPlus codes. The tip mach number for the chosen study was 0.35. The same configuration was used for experimental investigation for a comparative study. The LSD vane is formed using standard NACA profile with marginal modification at trailing edge. The performance parameters obtained form numerical studies at the exit of impeller and the diffuser have been compared with the corresponding experimental data. These parameters are pressure ratio, polytropic efficiency and flow angle at the impeller exit where as the parameters those have been compared at the exit of diffuser are the static pressure recovery coefficient and the exit flow angle. In addition, the numerical prediction of the blade loading in terms of blade surface pressure distribution on LSD vane has been compared with the corresponding experimental results. Static pressure recovery coefficient and flow angle at diffuser exit is seen to match closely at higher flows. The difference at lower flows could be due to the effect of interaction between impeller and diffuser combinations, as the numerical analysis was done separately for impeller and diffuser and the effect of impeller diffuser interaction was not considered.

Surge Inception in a Transonic Centrifugal Compressor Stage

2011 ◽  
Author(s):  
Isabelle Tre´binjac ◽  
Nicolas Bulot ◽  
Xavier Ottavy ◽  
Nicolas Buffaz
Keyword(s):  
Centrifugal Compressor ◽  
Short Wavelength ◽  
Stokes Equations ◽  
Pressure Sensors ◽  
Experimental Investigations ◽  
Compressor Stage ◽  
Vaned Diffuser ◽  
Choked Flow ◽  
Centrifugal Compressor Stage ◽  
Transonic Centrifugal Compressor

Numerical and experimental investigations were conducted in a transonic centrifugal compressor stage composed of a backswept splittered unshrouded impeller and a vaned diffuser. Unsteady 3D simulations were performed with the code elsA that solves the turbulent averaged Navier-Stokes equations, at three operating points: choked flow, peak efficiency and near surge. Unsteady pressure measurements up to 150 kHz were carried out in the entry zone of the vaned diffuser (in the vaneless space and in the semi-vaneless space) when the compressor came into surge. These static pressure sensors were mounted on the shroud enwall. The paper focuses on the vaneless and semi-vaneless space where the surge originates. A detailed analysis of the flow pattern coming from the unsteady computations from choked flow towards surge led to identify the physical mechanisms involved in the surge inception. It is shown that, when approaching surge, the flow is destabilized by a severe modification of the shock system in the vaned diffuser inlet. The first perturbation is acquired from the transducer located just upstream of the shock foot (i.e. on the vane suction side surface), indicating a movement of the shock towards the vaneless space. This perturbation travels upstream and leads to the strongest short-wavelength perturbation acquired from the transducer located just upstream of the vane leading edge. This strongest short-wavelength perturbation which level may reach almost four times the mean exit pressure value triggers the full scale instability.

Study on Aerodynamic Redesign of a High Pressure Ratio Centrifugal Compressor

2010 ◽  
Author(s):  
Chaolei Zhang ◽  
Qinghua Deng ◽  
Zhenping Feng
Keyword(s):  
Centrifugal Compressor ◽  
Cfd Simulation ◽  
Pressure Ratio ◽  
Aerodynamic Performance ◽  
Compressor Stage ◽  
Operation Condition ◽  
Vaned Diffuser ◽  
Centrifugal Compressor Stage ◽  
Optimum Configuration ◽  
Operation Conditions

This paper describes the aerodynamic redesign and optimization of a typical single stage centrifugal compressor, in which the total pressure ratio was improved from the original 4.0 to final 5.0 with the restrictions of keeping the impeller tip diameter, the design rotational speed and the design mass flow rate unchanged. Firstly the backsweep angle and the outlet blade height of the impeller were adjusted and the vaned diffuser was redesigned. Then a sensitivity analysis of the aerodynamic performance correlated to the primary redesign centrifugal compressor stage with respect to the chosen redesign variables was conducted, according to the parameterized results of the impeller and the vaned diffuser. Secondly the impeller and the vaned diffuser were optimized respectively under the stage environment at the design operation condition to improve the stage isentropic efficiency by using a global optimization method which coupled Evolutionary Algorithm (EA) and Artificial Neural Network (ANN), provided by the commercial software NUMECA DESIGN-3D. Subsequently the detailed performance maps of the centrifugal compressor stage corresponding to the primary redesign configuration and the optimum configuration were presented by Computational Fluid Dynamics (CFD) simulation. Finally the flow fields correlated to the centrifugal compressor configurations before and after optimization at the design operation condition were also compared and analyzed in detail. As a result the design target was achieved after the primary redesign, as a 2.7% gain in stage efficiency and a 3.6% increase in stage pressure ratio were obtained when compared with the primary redesign configuration after optimization. Moreover, the aerodynamic performance of the optimum configuration at the off-design operation conditions was also improved.

Analytical and Test Experiences Using a Rib Diffuser in a High Flow Centrifugal Compressor Stage

2001 ◽  
Author(s):  
James M. Sorokes ◽  
Jason A. Kopko
Keyword(s):  
Centrifugal Compressor ◽  
Quantitative Agreement ◽  
High Flow ◽  
Flow Coefficient ◽  
Centrifugal Impeller ◽  
Compressor Stage ◽  
Vaneless Diffuser ◽  
Vaned Diffuser ◽  
Centrifugal Compressor Stage ◽  
Qualitative And Quantitative

The paper addresses the use of a rib style (partial height) vaned diffuser to improve the flowfield downstream of a high flow coefficient centrifugal impeller. Empirical and analytical (3-D CFD) results are presented for both the original vaneless diffuser and the replacement rib configuration. Comparisons are made between the CFD results and the data obtained through single stage rig (SSTR) testing. Comments are offered regarding the qualitative and quantitative agreement between the empirical and analytical results.

On the Influence of the Diffuser Inlet Shape on the Performance of a Centrifugal Compressor Stage

1983 ◽  
Author(s):  
K. Bammert ◽  
M. Jansen ◽  
M. Rautenberg
Keyword(s):  
Experimental Study ◽  
Flow Field ◽  
Centrifugal Compressor ◽  
Field Measurements ◽  
Single Stage ◽  
Compressor Stage ◽  
Vaned Diffuser ◽  
Centrifugal Compressor Stage ◽  
Essential Components

Results from an experimental study of the influence of the diffuser inlet shape on the performance of the diffuser and the whole compressor stage are presented. The investigations were carried out using a single stage centrifugal compressor. Three different vaned diffusers were tested. From detailed flow field measurements the influence of the diffuser inlet shape on the performance of the essential components of the compressor stage, i.e. the impeller, the diffuser, and the collecting chamber was analyzed. It is shown that the reaction of the vaned diffuser on the efficiency of the impeller is only weak but the losses in the collecting chamber are considerably affected by the used diffuser types.

Sign in / Sign up

Export Citation Format

Share Document