Surgical Robot With Variable Remote Center of Motion Mechanism Using Flexible Structure

2018 ◽  
Vol 10 (3) ◽  
Author(s):  
Sho Yoshida ◽  
Takahiro Kanno ◽  
Kenji Kawashima
Keyword(s):  
Degrees Of Freedom ◽  
Translational Motion ◽  
Three Dimensional ◽  
Flexible Structure ◽  
Control Law ◽  
Surgical Robots ◽  
Pitch Motion ◽  
Bending Radius ◽  
Phantom Tissue ◽  
Pneumatic Cylinders

Remote center of motion (RCM) mechanisms are often used in surgical robots for laparoscopic surgery. In this paper, a RCM mechanism for holding a robotic forceps that facilitates adjustment using a flexible structure is proposed. The flexible structure is designed and manufactured with polypropylene-like resin material using a three-dimensional (3D) printer. Super elastic NI-Ti rods are inserted in the structure to have elasticity for bending and have rigidity for twisting. The structure achieves pitch motion around the remote center with two pneumatic cylinders. One cylinder drives the position and the other cylinder controls the bending radius of the structure. Therefore, the location of the remote center can be variable. This allows easier adjustment of the remote center before or during operation. The holder robot including the mechanism has four degrees-of-freedom (DOFs) in total, consisting of the pitch, a rotation around yaw axis, a translation in the direction of forceps insertion and a rotation of the forceps. Pneumatic rotary actuators are used for rotations and a cylinder is used for the translational motion. The model of the flexible structure is derived experimentally to design a controller for the pitch motion. A pneumatically driven robotic forceps is mounted on the holder to construct a master–slave control system. Experimental results show that the proposed control law achieves the desired rotational pitch motion. We compare the holder with a rigid link RCM holder and confirm the robustness of the proposed holder for variable remote center. Finally, the effectiveness of the system is confirmed with suturing tasks using a phantom tissue.

A First Example: The “Particle in a Box“ and Quantized Translational Motion

2020 ◽  
pp. 59-96
Author(s):  
Jochen Autschbach
Keyword(s):  
Degrees Of Freedom ◽  
Separation Of Variables ◽  
Translational Motion ◽  
Three Dimensional ◽  
Potential Wells ◽  
Quantum Tunnelling ◽  
Atomic Force ◽  
Quantum Behavior ◽  
The One ◽  
Three Degrees Of Freedom

The simple ‘particle in a box’ (Piab) is introduced in this chapter so that the reader can get familiar with applying the quantum recipe and atomic units. The PiaB is introduced in its one, two, and three dimensional variants, which demonstrates the use of the separation of variables technique as a strategy to solve the Schrodinger equation for a particle with two or three degrees of freedom. It is shown that the confinement of the particle causes the energy to be quantized. The one-dimensional PiaB is then applied to treat the electronic spectra of cyanine dyes and their absorption colors. The chapter then introduces more general setups with finite potential wells, in order to introduce the phenomenon of quantum tunnelling and to discuss more generally with the unintuitive ‘quantum behavior’ of particles such as electrons. Scanning tunnelling and atomic force microscopes are also discussed briefly.

scholarly journals Design, Fabrication, and Testing of a Novel 3D 3-Fingered Electrothermal Microgripper with Multiple Degrees of Freedom

Micromachines ◽  
2021 ◽  
Vol 12 (4) ◽  
pp. 444
Author(s):  
Guoning Si ◽  
Liangying Sun ◽  
Zhuo Zhang ◽  
Xuping Zhang
Keyword(s):  
Degrees Of Freedom ◽  
Dynamic Properties ◽  
Three Dimensional ◽  
Polyimide Film ◽  
Zebrafish Embryos ◽  
Multiple Degrees Of Freedom ◽  
Electrothermal Actuator ◽  
3D Space ◽  
Pick And Place

This paper presents the design, fabrication, and testing of a novel three-dimensional (3D) three-fingered electrothermal microgripper with multiple degrees of freedom (multi DOFs). Each finger of the microgripper is composed of a V-shaped electrothermal actuator providing one DOF, and a 3D U-shaped electrothermal actuator offering two DOFs in the plane perpendicular to the movement of the V-shaped actuator. As a result, each finger possesses 3D mobilities with three DOFs. Each beam of the actuators is heated externally with the polyimide film. The durability of the polyimide film is tested under different voltages. The static and dynamic properties of the finger are also tested. Experiments show that not only can the microgripper pick and place microobjects, such as micro balls and even highly deformable zebrafish embryos, but can also rotate them in 3D space.

scholarly journals Asymmetry in Three-Dimensional Sprinting with and without Running-Specific Prostheses

Symmetry ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 580
Author(s):  
Anna Lena Emonds ◽  
Katja Mombaur
Keyword(s):  
Degrees Of Freedom ◽  
Body Position ◽  
Three Dimensional ◽  
Problem Formulation ◽  
Contact Phase ◽  
Individual Level ◽  
Lower Trunk ◽  
Floating Base ◽  
The Asymmetry ◽  
Limb Asymmetry

As a whole, human sprinting seems to be a completely periodic and symmetrical motion. This view is changed when a person runs with a running-specific prosthesis after a unilateral amputation. The aim of our study is to investigate differences and similarities between unilateral below-knee amputee and non-amputee sprinters—especially with regard to whether asymmetry is a distracting factor for sprint performance. We established three-dimensional rigid multibody models of one unilateral transtibial amputee athlete and for reference purposes of three non-amputee athletes. They consist of 16 bodies (head, ipper, middle and lower trunk, upper and lower arms, hands, thighs, shanks and feet/running specific prosthesis) with 30 or 31 degrees of freedom (DOFs) for the amputee and the non-amputee athletes, respectively. Six DOFs are associated with the floating base, the remaining ones are rotational DOFs. The internal joints are equipped with torque actuators except for the prosthetic ankle joint. To model the spring-like properties of the prosthesis, the actuator is replaced by a linear spring-damper system. We consider a pair of steps which is modeled as a multiphase problem with each step consisting of a flight, touchdown and single-leg contact phase. Each phase is described by its own set of differential equations. By combining motion capture recordings with a least squares optimal control problem formulation including constraints, we reconstructed the dynamics of one sprinting trial for each athlete. The results show that even the non-amputee athletes showed less symmetrical sprinting than expected when examined on an individual level. Nevertheless, the asymmetry is much more pronounced in the amputee athlete. The amputee athlete applies larger torques in the arm and trunk joints to compensate the asymmetry and experiences a destabilizing influence of the trunk movement. Hence, the inter-limb asymmetry of the amputee has a significant effect on the control of the sprint movement and the maintenance of an upright body position.

Kinematic Analysis and Optimization of a Novel Robot for Surgical Tool Manipulation

2008 ◽  
Author(s):  
Xiaoli Zhang ◽  
Carl A. Nelson
Keyword(s):  
Inverse Kinematics ◽  
Degrees Of Freedom ◽  
Force Feedback ◽  
Robotic Systems ◽  
Small Space ◽  
Surgical Robots ◽  
Tool Positioning ◽  
Rotation Axes ◽  
Surgical Tool ◽  
Linear Nature

The size and limited dexterity of current surgical robotic systems are factors which limit their usefulness. To improve the level of assimilation of surgical robots in minimally invasive surgery (MIS), a compact, lightweight surgical robotic positioning mechanism with four degrees of freedom (DOF) (three rotational DOF and one translation DOF) is proposed in this paper. This spatial mechanism based on a bevel-gear wrist is remotely driven with three rotation axes intersecting at a remote rotation center (the MIS entry port). Forward and inverse kinematics are derived, and these are used for optimizing the mechanism structure given workspace requirements. By evaluating different spherical geared configurations with various link angles and pitch angles, an optimal design is achieved which performs surgical tool positioning throughout the desired kinematic workspace while occupying a small space bounded by a hemisphere of radius 13.7 cm. This optimized workspace conservatively accounts for collision avoidance between patient and robot or internally between the robot links. This resultant mechanism is highly compact and yet has the dexterity to cover the extended workspace typically required in telesurgery. It can also be used for tool tracking and skills assessment. Due to the linear nature of the gearing relationships, it may also be well suited for implementing force feedback for telesurgery.

scholarly journals Estimation of Wave Period from Pitch and Roll of a Lidar Buoy

Sensors ◽  
2021 ◽  
Vol 21 (4) ◽  
pp. 1310
Author(s):  
Andreu Salcedo-Bosch ◽  
Francesc Rocadenbosch ◽  
Miguel A. Gutiérrez-Antuñano ◽  
Jordi Tiana-Alsina
Keyword(s):  
Degrees Of Freedom ◽  
Translational Motion ◽  
Cutoff Frequency ◽  
Peak Level ◽  
Wave Period ◽  
Estimation Methods ◽  
Zero Crossing ◽  
Power Spectral ◽  
Period Estimation ◽  
Wind Lidar

This work proposes a new wave-period estimation (L-dB) method based on the power-spectral-density (PSD) estimation of pitch and roll motional time series of a Doppler wind lidar buoy under the assumption of small angles (±22 deg) and slow yaw drifts (1 min), and the neglection of translational motion. We revisit the buoy’s simplified two-degrees-of-freedom (2-DoF) motional model and formulate the PSD associated with the eigenaxis tilt of the lidar buoy, which was modelled as a complex-number random process. From this, we present the L-dB method, which estimates the wave period as the average wavelength associated to the cutoff frequency span at which the spectral components drop off L decibels from the peak level. In the framework of the IJmuiden campaign (North Sea, 29 March–17 June 2015), the L-dB method is compared in reference to most common oceanographic wave-period estimation methods by using a TriaxysTM buoy. Parametric analysis showed good agreement (correlation coefficient, ρ = 0.86, root-mean-square error (RMSE) = 0.46 s, and mean difference, MD = 0.02 s) between the proposed L-dB method and the oceanographic zero-crossing method when the threshold L was set at 8 dB.

Three-dimensional asymmetric maximum weight lifting prediction considering dynamic joint strength

2021 ◽  
pp. 095441192098703
Author(s):  
Rahid Zaman ◽  
Yujiang Xiang ◽  
Jazmin Cruz ◽  
James Yang
Keyword(s):  
Experimental Data ◽  
Degrees Of Freedom ◽  
Inverse Dynamics ◽  
Three Dimensional ◽  
Optimization Method ◽  
Weight Lifting ◽  
Joint Torque ◽  
Maximum Weight ◽  
Angular Velocities ◽  
Asymmetric Lifting

In this study, the three-dimensional (3D) asymmetric maximum weight lifting is predicted using an inverse-dynamics-based optimization method considering dynamic joint torque limits. The dynamic joint torque limits are functions of joint angles and angular velocities, and imposed on the hip, knee, ankle, wrist, elbow, shoulder, and lumbar spine joints. The 3D model has 40 degrees of freedom (DOFs) including 34 physical revolute joints and 6 global joints. A multi-objective optimization (MOO) problem is solved by simultaneously maximizing box weight and minimizing the sum of joint torque squares. A total of 12 male subjects were recruited to conduct maximum weight box lifting using squat-lifting strategy. Finally, the predicted lifting motion, ground reaction forces, and maximum lifting weight are validated with the experimental data. The prediction results agree well with the experimental data and the model’s predictive capability is demonstrated. This is the first study that uses MOO to predict maximum lifting weight and 3D asymmetric lifting motion while considering dynamic joint torque limits. The proposed method has the potential to prevent individuals’ risk of injury for lifting.

Determination of the Workspace of a Three-Degrees-of-Freedom Parallel Manipulator Using a Three-Dimensional Computer-Aided-Design Software Package and the Concept of Virtual Chains1

2015 ◽  
Vol 8 (2) ◽  
Author(s):  
Andrew Johnson ◽  
Xianwen Kong ◽  
James Ritchie
Keyword(s):  
Computer Aided Design ◽  
Parallel Manipulator ◽  
Degrees Of Freedom ◽  
Graphical Representation ◽  
Three Dimensional ◽  
Parallel Manipulators ◽  
Workspace Analysis ◽  
Computer Aided ◽  
Aided Design

The determination of workspace is an essential step in the development of parallel manipulators. By extending the virtual-chain (VC) approach to the type synthesis of parallel manipulators, this technical brief proposes a VC approach to the workspace analysis of parallel manipulators. This method is first outlined before being illustrated by the production of a three-dimensional (3D) computer-aided-design (CAD) model of a 3-RPS parallel manipulator and evaluating it for the workspace of the manipulator. Here, R, P and S denote revolute, prismatic and spherical joints respectively. The VC represents the motion capability of moving platform of a manipulator and is shown to be very useful in the production of a graphical representation of the workspace. Using this approach, the link interferences and certain transmission indices can be easily taken into consideration in determining the workspace of a parallel manipulator.

Biomechanical characteristics of C1–2 cable fixations

1996 ◽  
Vol 85 (2) ◽  
pp. 316-322 ◽  
Author(s):  
Curtis A. Dickman ◽  
Neil R. Crawford ◽  
Christopher G. Paramore
Keyword(s):  
Cyclic Loading ◽  
Translational Motion ◽  
Biomechanical Testing ◽  
Three Dimensional ◽  
Constrained Motion ◽  
Content Type ◽  
Physiological Range ◽  
Fixation Techniques ◽  
Cable Fixation ◽  
Fine Print

✓ The biomechanical characteristics of four different methods of C1–2 cable fixation were studied to assess the effectiveness of each technique in restoring atlantoaxial stability. Biomechanical testing was performed on the upper cervical spines of four human cadaveric specimens. Physiological range loading was applied to the atlantoaxial specimens and three-dimensional motion was analyzed with stereophotogrammetry. The load–deformation relationships and kinematics were measured, including the stiffness, the angular ranges of motion, the linear ranges of motion, and the axes of rotation. Specimens were nondestructively tested in the intact state, after surgical destabilization, and after each of four different methods of cable fixation. Cable fixation techniques included the interspinous technique, the Brooks technique, and two variants of the Gallie technique. All specimens were tested immediately after fixation and again after the specimen was fatigued with 6000 cycles of physiological range torsional loading. All four cable fixation methods were moderately flexible immediately; the different cable fixations allowed between 5° and 40° of rotational motion and between 0.6 and 7 mm of translational motion to occur at C1–2. The Brooks and interspinous methods controlled C1–2 motion significantly better than both of the Gallie techniques. The motion allowed by one of the Gallie techniques did not differ significantly from the motion of the unfixed destabilized specimens. All cable fixation techniques loosened after cyclic loading and demonstrated significant increases in C1–2 rotational and translational motions. The bone grafts shifted during cyclic loading, which reduced the effectiveness of the fixation. The locations of the axes of rotation, which were unconstrained and mobile in the destabilized specimens, became altered with cable fixation. The C1–2 cables constrained motion by shifting the axes of rotation so that C-1 rotated around the fixed cable and graft site. After the specimen was fatigued, the axes of rotation became more widely dispersed but were usually still localized near the cable and graft site. Adequate healing requires satisfactory control of C1–2 motion. Therefore, some adjunctive fixation is advocated to supplement the control of motion after C1–2 cable fixation (that is, a cervical collar, a halo brace, or rigid internal fixation with transarticular screws).

Investigation of Train Dynamics in Passing Through Curves Using a Full Model

Joint Rail ◽  
2004 ◽  
Author(s):  
Mohammad Durali ◽  
Mohammad Mehdi Jalili Bahabadi
Keyword(s):  
Degrees Of Freedom ◽  
Equations Of Motion ◽  
Three Dimensional ◽  
Full Model ◽  
Bogie Frame ◽  
Nonlinear Characteristics ◽  
Train Derailment ◽  
Train Dynamics

In this article a train model is developed for studying train derailment in passing through bends. The model is three dimensional, nonlinear, and considers 43 degrees of freedom for each wagon. All nonlinear characteristics of suspension elements as well as flexibilities of wagon body and bogie frame, and the effect of coupler forces are included in the model. The equations of motion for the train are solved numerically for different train conditions. A neural network was constructed as an element in solution loop for determination of wheel-rail contact geometry. Derailment factor was calculated for each case. The results are presented and show the major role of coupler forces on possible train derailment.

Sign in / Sign up

Export Citation Format

Share Document