Optimum Fin Parameters of Radial Heat Sinks Subjected to Natural Convection

2019 ◽  
Vol 11 (5) ◽  
Author(s):  
S. Manna ◽  
S. K. Ghosh ◽  
S. C. Haldar
Keyword(s):  
Heat Transfer ◽  
Heat Sink ◽  
Heat Sinks ◽  
Computational Domain ◽  
Active Length ◽  
Vorticity Vector ◽  
Radial Heat ◽  
In The Beginning ◽  
Opposing Effects ◽  
Fin Thickness

Free convection from an upward facing radial heat sink with fins at an equal angular gap attached to an isothermal base has been investigated numerically. The governing equations in primitive variables were changed to vorticity-vector potential formulation, and an in-house code was developed using finite difference technique. To close the computational domain, two pseudo boundaries were considered. Length, height, and number of fins strongly influence the rate of heat transfer while the fin thickness has a marginal role. As the fin length increases, the rate of heat transfer first increases and then remains almost unaffected. However, the active length of the fins depends on the strength of buoyancy. Heat transfer continuously increases with fin height but with diminishing effect. Adding more number of fins has two opposing effects. It provides more surface area for convection, but at the same time, the induced air is unable to reach the interior of the heat sink making the inner portion of the fins inoperative. As a result of these two opposing influences, heat transfer increases in the beginning and then decreases as more fins are added. This article suggests various fin parameters to achieve maximum cooling. In addition, one can estimate the rate of cooling to be achieved by any radial heat sink.

Enhanced Heat Transfer in Radial Heat Sinks for LED Lamps

2018 ◽  
Author(s):  
Fernando Cano-Banda ◽  
Ana Gallardo-Gutierrez ◽  
Jesus Garcia-Gonzalez ◽  
Abel Hernandez-Guerrero ◽  
Luis Luviano-Ortiz
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Heat Sink ◽  
Heat Dissipation ◽  
Heat Sinks ◽  
Output Analysis ◽  
Maximum Heat ◽  
Maximum Heat Transfer ◽  
Longitudinal Orientation ◽  
Radial Heat

A radial design of a passive heat sink for cooling LED illumination devices is analyzed numerically in order to identify the geometric shape that promotes better heat dissipation rates. Natural convection with the surrounding is considered during the operation of the heat sink. Due to the fact that natural convection is the main mechanism of heat transfer, the shape of the heat sink has a high influence in the heat dissipated. An analysis of the influence of different parameters of a heat sink is conducted in the presented study. The radial heat sink under analysis consists in a flat disc with rectangular fins on it, and the fins are distributed with a radial longitudinal orientation in a circular row arrangement. The number of rows can vary but there is a constant relation of two times the number of fins between the number of fins in an inner row and the next outer row. In order to find a correct configuration to improve the dissipation of heat, parameters like the number of fins, the length of the fins and the separation between fins are studied. The average Nusselt number and thermal resistance for each geometric configuration are compared. The output analysis provides the best shape for a maximum heat transfer.

Heat-Transfer Characteristics and Design Optimization for a Small-Sized Plate-Fin Heat Sink Array

2007 ◽  
Vol 129 (4) ◽  
pp. 518-521 ◽  
Author(s):  
Gaowei Xu ◽  
Yingjun Cheng ◽  
Le Luo
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Heat Sink ◽  
Convective Heat Transfer Coefficient ◽  
Heat Sinks ◽  
Heat Transfer Characteristics ◽  
Fin Thickness

The heat-transfer characteristics of 128 small-sized plate-fin heat sinks in a supercomputer chassis are investigated with CFD simulation. The V-shaped curves of the chip temperature versus fin pitch and fin thickness are derived and a thermal resistance model is built to explore the profile and obtain the convective heat-transfer coefficient of the heat sinks. It turns out that the V-shaped profile arises from the joint action of the thermal conduction and convection of heat sink, which can be attributed to the intricacy of the dependencies of thermal resistances on either fin pitch or thickness. It can be further concluded that Biot criterion is applicable to estimate the Biot number of large-scale plate-fin heat sink but not applicable for the small-sized one. The convective heat-transfer coefficient is a complicated function of fin pitch and fin thickness. The empirical formulas of heat transfer are obtained and the fin pitch and fin thickness are optimized.

Proposal of a Micro/Mini Cooling Device Using Fins-Installed Porous Media for High Heat Flux Removal Exceeding 1000W/cm2

2009 ◽  
Author(s):  
Kazuhisa Yuki ◽  
Akira Matsui ◽  
Hidetoshi Hashizume ◽  
Koichi Suzuki
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Sink ◽  
Heat Transfer Performance ◽  
High Heat ◽  
Heat Sinks ◽  
High Heat Flux ◽  
Transfer Performance ◽  
Cooling Device ◽  
Fin Thickness

Heat transfer characteristics of micro-sized bronze particle-sintered porous heat sinks and copper minichannel-fins heat sinks are experimentally investigated in order to clarify the feasibility of a newly proposed micro/mini cooling device using fins-installed porous media. Regarding the porous heat sinks, fin effect toward more inside of the porous medium is promoted by sintering the porous heat sink on the heat transfer surface, which results in increasing the heat transfer performance up to 0.8MW/m2K at heat flux of 8.2MW/m2 though there still remains a large pressure loss issue. In addition, the results clarify that the heat exchanging area exists only in the vicinity of the heat transfer surface. As to the minichannel-fins heat sinks, the influence of the channel width and the fin thickness are evaluated in detail. As a result, the minichannel-fins heat sink having the narrower channel width (i.e. scale effect) and lower porosity (i.e. thicker fin thickness with larger heat capacity) achieves higher heat transfer performance up to 0.10MW/m2K at 8.3MW/m2. However, rapid increase of pressure loss, which is occasionally observed in a microchannel due to vapor bubbles choking the narrow channel, still remains as an issue under flow boiling conditions in the minichannel. Finally, heat transfer performance of the fin-installed porous heat sink is numerically predicted by the control volume method. The simulation confirms that the heat transfer coefficient at each wall superheat of 0 and 30 degrees has performance 2.5 times and 2.0 times higher than that of the normal fins, which indicates that this heat sink coupling the micro and mini channels has high potential as efficient cooling method under high heat flux conditions exceeding 10MW/m2.

Comparison of the Effect of Embedded Grooves on the Heat Removal and Pressure Drop in Microchannel Heat Sinks

2011 ◽  
Author(s):  
Farnaz Faily ◽  
Haleh Shafeie ◽  
Omid Abouali
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Heat Sink ◽  
Heat Removal ◽  
Heat Sinks ◽  
Coefficient Of Performance ◽  
Maximum Heat ◽  
Different Types ◽  
Microchannel Heat Sinks ◽  
Fin Thickness

This paper presents a numerical study for the single phase heat transfer of water in the heat sinks with different types of the grooved microchannels. The cross section of the grooves is either rectangular or arced shape. The grooves are embedded vertically in the side walls of the microchannel but for the floor, different orientation angles of the grooves in the range of 0–60° are investigated. As well, for the grooves on the floor of the channel, the chevron-shape is another pattern which has bee studied. A 3-D computational model is developed for each of the studied cases and the conjugate heat transfer in both solid and liquid is investigated. The governing equations are solved numerically to determine the pressure drop and heat transfer through the heat sink. The results of the heat removal and coefficient of performance (COP) for different types of the grooved microchannel heat sinks are compared to each other as well with those for a simple microchannel heat sink with minimum fin thickness. The comparison shows that the case with minimum vertical fin thickness and arc grooves aligned in 60° on the floor has the maximum heat removal and COP among the studied cases.

Fluid Flow and Heat Transfer of Liquid Sodium in Small-Scale Heat Sinks With Different Geometries

2021 ◽  
Author(s):  
Mahyar Pourghasemi ◽  
Nima Fathi
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Cross Sections ◽  
Heat Sink ◽  
Volume Ratio ◽  
Heat Sinks ◽  
Liquid Sodium ◽  
Small Scale ◽  
Nusselt Numbers ◽  
The Difference

Abstract 3-D numerical simulations are performed to investigate liquid sodium (Na) flow and the heat transfer within miniature heat sinks with different geometries and hydraulic diameters of less than 5 mm. Two different straight small-scale heat sinks with rectangular and triangular cross-sections are studied in the laminar flow with the Reynolds number up to 1900. The local and average Nusselt numbers are obtained and compared against eachother. At the same surface area to volume ratio, rectangular minichannel heat sink leads to almost 280% higher convective heat transfer rate in comparison with triangular heat sink. It is observed that the difference between thermal efficiencies of rectangular and triangular minichannel heat sinks was independent of flow Reynolds number.

Pin-Fin Heat Sink With Horizontal Base and Blocked Edges

2008 ◽  
Author(s):  
D. Sahray ◽  
H. Shmueli ◽  
N. Segal ◽  
G. Ziskind ◽  
R. Letan
Keyword(s):  
Heat Transfer ◽  
Free Convection ◽  
Contact Resistance ◽  
Cross Section ◽  
Heat Input ◽  
Heat Sink ◽  
Numerical Study ◽  
Heat Sinks ◽  
Transfer Enhancement ◽  
Pin Fin

In the present work, horizontal-base pin fin heat sinks exposed to free convection in air are studied. They are made of aluminum, and there is no contact resistance between the base and the fins. For the same base dimensions the fin height and pitch vary. The fins have a constant square cross-section. The edges of the sink are blocked: the surrounding insulation is flush with the fin tips. The effect of fin height and pitch on the performance of the sink is studied experimentally and numerically. In the experiments, the heat sinks are heated using foil electrical heaters. The heat input is set, and temperatures of the base and fins are measured. In the corresponding numerical study, the sinks and their environment are modeled using the Fluent 6 software. The results show that heat transfer enhancement due to the fins is not monotonic. The differences between sparsely and densely populated sinks are analyzed for various fin heights. Also assessed are effects of the blocked edges as compared to the previously studied cases where the sink edges were exposed to the surroundings.

Compact Modeling of Fluid Flow and Heat Transfer in Straight Fin Heat Sinks

2004 ◽  
Vol 126 (2) ◽  
pp. 247-255 ◽  
Author(s):  
Duckjong Kim ◽  
Sung Jin Kim
Keyword(s):  
Heat Transfer ◽  
Porous Medium ◽  
Fluid Flow ◽  
Pressure Drop ◽  
Heat Sink ◽  
Volume Averaging ◽  
Thermal Design ◽  
Heat Sinks ◽  
Compact Modeling ◽  
Flow And Heat Transfer

In the present work, a compact modeling method based on a volume-averaging technique is presented. Its application to an analysis of fluid flow and heat transfer in straight fin heat sinks is then analyzed. In this study, the straight fin heat sink is modeled as a porous medium through which fluid flows. The volume-averaged momentum and energy equations for developing flow in these heat sinks are obtained using the local volume-averaging method. The permeability and the interstitial heat transfer coefficient required to solve these equations are determined analytically from forced convective flow between infinite parallel plates. To validate the compact model proposed in this paper, three aluminum straight fin heat sinks having a base size of 101.43mm×101.43mm are tested with an inlet velocity ranging from 0.5 m/s to 2 m/s. In the experimental investigation, the heat sink is heated uniformly at the bottom. The resulting pressure drop across the heat sink and the temperature distribution at its bottom are then measured and are compared with those obtained through the porous medium approach. Upon comparison, the porous medium approach is shown to accurately predict the pressure drop and heat transfer characteristics of straight fin heat sinks. In addition, evidence indicates that the entrance effect should be considered in the thermal design of heat sinks when Re Dh/L>∼O10.

Performance Comparison of Microchannel Heat Sink Using Boron-Based Ceramic Materials

2021 ◽  
Vol 1163 ◽  
pp. 73-88
Author(s):  
Md Tanbir Sarowar
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Sink ◽  
Electronic Devices ◽  
Ceramic Materials ◽  
Substrate Material ◽  
Heat Sinks ◽  
Maximum Temperature ◽  
Microchannel Heat Sink ◽  
Small Surface

Microchannel heat sink plays a vital role in removing a considerable amount of heat flux from a small surface area from different electronic devices. In recent times, the rapid development of electronic devices requires the improvement of these heat sinks to a greater extent. In this aspect, the selection of appropriate substrate materials of the heat sinks is of vital importance. In this paper, three boron-based ultra-high temperature ceramic materials (ZrB2, TiB2, and HfB2) are compared as a substrate material for the microchannel heat sink using a numerical approach. The fluid flow and heat transfer are analyzed using the finite volume method. The results showed that the maximum temperature of the heat source didn’t exceed 355K at 3.6MWm-2 for any material. The results also indicated HfB2 and TiB2 to be more useful as a substrate material than ZrB2. By applying 3.6 MWm-2 heat flux at the source, the maximum obtained surface heat transfer coefficient was 175.2 KWm-2K-1 in a heat sink having substrate material HfB2.

Two-Phase Heat Sinks With Microporous Coating

2011 ◽  
Author(s):  
Tadej Semenic ◽  
Seung M. You
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Sink ◽  
Heat Sinks ◽  
Porous Coating ◽  
Two Phase ◽  
Small Channel ◽  
Rectangular Channels ◽  
Microporous Coating ◽  
Channel Aspect Ratio

To minimize flow boiling instabilities in two-phase heat sinks, two different types of microporous coatings were developed and applied on mini- and small-channel heat sinks and tested using degassed R245fa refrigerant. The first coating was epoxy-based and was sprayed on heat sink channels while the second coating was formed by sintering copper particles on heat sink channels. Mini-channel heat sinks had overall dimensions 25.4 mm × 25.4 mm × 6.4 mm and twelve rectangular channels with a hydraulic diameter 1.7 mm and a channel aspect ratio of 2.7. Small-channel heat sinks had the same overall dimensions, but only three rectangular channels with hydraulic diameter 4.1 mm and channel aspect ratio 0.6. The microporous coatings were found to minimize parallel channel instabilities for mini-channel heat sinks and to reduce the amplitude of heat sink base temperature oscillations from 6 °C to slightly more than 1 °C. No increase in pressure drop or pumping power due to the microporous coating was measured. The mini-channel heat sinks with porous coating had in average 1.5-times higher heat transfer coefficient than uncoated heat sinks. Also, the small-channel heat sinks with the “best” porous coating had in average 2.5-times higher heat transfer coefficient and the critical heat flux was 1.5 to 2-times higher compared with the uncoated heat sinks.

Thermal Performance Measurement for Confined Heat Sinks by Using a Modified Transient Liquid Crystal Technique

2003 ◽  
Author(s):  
S. T. Kuo ◽  
M. P. Wang ◽  
M. C. Wu ◽  
Y. H. Hung
Keyword(s):  
Heat Transfer ◽  
Liquid Crystal ◽  
Heat Sink ◽  
Heat Sinks ◽  
Experimental Investigations ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics ◽  
Flow And Heat Transfer ◽  
Preheating Temperature ◽  
Parametric Studies

A series of experimental investigations with a new modified transient liquid crystal method on the studies related to the fluid flow and heat transfer characteristics in a channel installed with a heat sink have been successfully performed. The parametric studies on the local and average effective heat transfer characteristics for confined heat sinks have been explored. The influencing parameters and conditions include air preheating temperature at channel inlet, flow velocity and heat sink types. Besides, a concept of the amount of enhanced heat transfer (AEHT) is introduced and defined as the ratio of j/f. The j/f ratio is almost independent of Reynolds number for a specific confined heat sink. The j/f ratios are 0.0603 and 0.0124 for fully-confined and unconfined heat sinks, respectively.

Sign in / Sign up

Export Citation Format

Share Document