A Model for Stall and Surge in Low-Speed Contra-Rotating Fans

2019 ◽  
Vol 141 (8) ◽  
Author(s):  
Mohammad Javad Shahriyari ◽  
Hossein Khaleghi ◽  
Martin Heinrich
Keyword(s):  
Rotational Speed ◽  
Current Model ◽  
Characteristic Curve ◽  
Pressure Rise ◽  
Rotating Stall ◽  
Negative Slope ◽  
Initial Slope ◽  
Speed Ratio ◽  
Low Speed ◽  
Fan Performance

This paper reports on a theory for poststall transients in contra-rotating fans, which is developed from the basic Moore–Greitzer theory. A second-order hysteresis term is assumed for the fan pressure rise, which gives the theory more capabilities in predicting the fan instabilities. The effect of the rotational speed ratio of the two counter rotating rotors on the fan performance during the occurrence of surge and rotating stall are studied (the rotational speed of the front rotor is assumed to be kept constant whereas the speed of the rear rotor is variable). One of the new capabilities of the current model is the possibility of investigating the effect of the initial slope on the fan characteristic. Results reveal that unlike the conventional fans and compressors, in the current contra-rotating fan stall cannot be initiated from the negative slope portion of the fan pressure rise characteristic curve. One of the important advantages of the developed model is that it enables investigation of the effect of the rate of throttling on the instabilities. Results show that more the rotational speed of the rear rotor, the more robust to surge (caused by throttling) the fan is.

Effect of Tip Clearance on Stall Evolution Process in a Low-Speed Axial Compressor Stage

2004 ◽  
Author(s):  
Masahiro Inoue ◽  
Motoo Kuroumaru ◽  
Shinichi Yoshida ◽  
Takahiro Minami ◽  
Kazutoyo Yamada ◽  
...  
Keyword(s):  
Spectral Power ◽  
Axial Compressor ◽  
Pressure Rise ◽  
Rotating Stall ◽  
Short Length ◽  
Tip Clearance ◽  
Evolution Process ◽  
Length Scale ◽  
Compressor Stage ◽  
Low Speed

Effect of the tip clearance on the transient process of rotating stall evolution has been studied experimentally in a low-speed axial compressor stage with various stator-rotor gaps. In the previous authors’ experiments for the small tip clearance, the stall evolution process of the rotor was sensitive to the gaps between the blade rows. For the large tip clearance, however, little difference is observed in the evolution processes independently of the blade row gap. In the first half process, it is characterized by gradual reduction of overall pressure-rise with flow rate decreasing, and the number of short length-scale disturbances is increasing with their amplitude increasing. In the latter half a long length-scale disturbance develops rapidly to result in deep stall. Just before the stall inception the spectral power density of the casing wall pressure reveals the existence of rotating disturbances with broadband high frequency near a quarter of the blade passing frequency. This is caused by the short length-scale disturbances occurring intermittently. A flow model is presented to explain mechanisms of the rotating short length-scale disturbance, which includes a tornado-like separation vortex and tip-leakage vortex breakdown. The model is supported by a result of a numerical unsteady flow simulation.

An Experimental Study of Stall Suppression and Associated Changes to the Flow Structures in the Tip Region of an Axial Low Speed Fan Rotor by Axial Casing Grooves

2017 ◽  
Author(s):  
Huang Chen ◽  
Yuanchao Li ◽  
Subhra Shankha Koley ◽  
Nick Doeller ◽  
Joseph Katz
Keyword(s):  
Flow Rate ◽  
Large Scale ◽  
Pressure Rise ◽  
Leading Edge ◽  
Suction Side ◽  
Rotating Stall ◽  
Flow Structures ◽  
Flow Angle ◽  
Low Speed ◽  
Flow Characterization

The effects of axial casing grooves on the performance and flow structures in the tip region of an axial low speed fan rotor have been studied experimentally in the JHU refractive index-matched liquid facility. The four-per-passage semicircular grooves are skewed by 45° in the positive circumferential direction, and have a diameter of 65% of the rotor blade axial chord length. A third of the groove overlaps with the blade front, and the rest extends upstream. These grooves have a dramatic effect on the machine performance, reducing the stall flow rate by 40% compared to the same machine with a smooth endwall. However, they reduce the pressure rise at high flow rates. The flow characterization consists of qualitative visualizations of vortical structures using cavitation, as well as stereo-PIV (SPIV) measurements in several meridional and (z,θ) planes covering the tip region and interior of the casing grooves. The experiments are performed at a flow rate corresponding to pre-stall conditions for the untreated machine. They show that the flow into the downstream sides of the grooves and the outflow from their upstream sides vary periodically. The inflow peaks when the downstream end is aligned with the pressure side (PS) of the blade, and decreases, but does not vanish, when this end is located near the suction side (SS). These periodic variations have three primary effects: First, substantial fractions of the leakage flow and the tip leakage vortex (TLV) are entrained periodically into the groove. Consequently, in contrast to the untreated flow, The TLV remnants remain confined to the vicinity of the entrance to the groove, and the TLV strength diminishes starting from the mid-chord. Second, the grooves prevent the formation of large scale backflow vortices (BFVs), which are associated with the TLV, propagate from one blade passage to the next, and play a key role in the onset of rotating stall in the untreated fan. Third, the flow exiting from the grooves causes periodic variations of about 10° in the relative flow angle around the blade leading edge, presumably affecting the blade loading. The distributions of turbulent kinetic energy provide statistical evidence that in contrast to the untreated casing, very little turbulence originating from a previous TLV, including the BFVs, propagates from the PS to the SS of the blade. Hence, the TLV-related turbulence remain confined to the entrance to groove. Elevated, but lower turbulence is also generated as the outflow from the groove jets into the passage.

Clearance Effects on Centrifugal Compressor Characteristic and Stability

2007 ◽  
Author(s):  
Yong Sang Yoon ◽  
Shin Hyung Kang ◽  
Seung Jin Song
Keyword(s):  
Centrifugal Compressor ◽  
Rotational Speed ◽  
Pressure Rise ◽  
Rotating Stall ◽  
Tip Clearance ◽  
Flow Coefficient ◽  
Component Level ◽  
Stall Inception ◽  
Stability Model ◽  
Number Of Cells

The effects of impeller inlet tip clearance and diffuser width on centrifugal compressor characteristic and stability have been experimentally investigated in a centrifugal compressor with a vaneless diffuser. An increase in the impeller inlet tip clearance decreases the overall pressure rise across the compressor, mainly due to the tip clearance loss in the impeller. However, the effect of inlet tip clearance on diffuser pressure rise or compressor stability is weak. A decrease in the diffuser width significantly lowers the compressor pressure rise, especially at hight flow rates. At the component level, the impeller is insensitive to the diffuser width variation, and the pressure rise across the diffuser actually increases as diffuser width is decreased. Upon further investigation, it has been found that the overall compressor characteristic is strongly influenced by the region between the impeller exit and the diffuser inlet. Also, a decrease in the diffuser width delays stall inception by increasing the radial velocity of the flow in the diffuser. Thus, the stalling flow coefficient is more sensitive to the variation in the diffuser than the inlet tip clearance. In all cases, rotating stall consists of two or three cells rotating at about approximately one tenth of the compressor rotational speed. When the number of cells changes from three to two, the rotational speed drops. However, when the number of cells remains constant, the cells’ rotational speed increases as flow coefficient is lowered. All of these trends agree well with predictions from a new stability model developed by the first author.

Effect of Speed Ratio and Axial Spacing Variations on the Performance of a High Aspect Ratio, Low Speed Contra-Rotating Fan

2012 ◽  
Author(s):  
Chetan S. Mistry ◽  
A. M. Pradeep
Keyword(s):  
Aspect Ratio ◽  
Numerical Simulations ◽  
High Aspect Ratio ◽  
Total Pressure ◽  
Experimental Studies ◽  
Pressure Rise ◽  
Operating Conditions ◽  
Speed Ratio ◽  
Stall Margin ◽  
Low Speed

This paper explores the effect of speed ratio and axial spacing between high aspect ratio, low speed contra-rotating pair rotors on their aerodynamic performance. The blades were designed with a low hub-tip ratio of 0.35 and an aspect ratio of 3.0. Numerical and experimental studies are carried out on these contra-rotating rotors operating at a Reynolds number of 1.258 × 105 (based on blade chord). The first and second rotors were designed to develop a pressure rise of 1100 Pa and 900 Pa, respectively, for total mass flow rate of 6 kg/s when both operating at a design speed of 2400 rpm. The performance of the fan was evaluated based on variations of total pressure and flow angles at off-design operating conditions. The measurementsof total pressure rise, flow angles etc. are taken upstream of the first rotor and in between the two rotors and downstream of the second rotor. The performance of the contra rotating stage is mainly influenced by the axial spacing between the rotors and speed ratio of both the rotors. The study reveals that the aerodynamics of the contra-rotating stage and stall margin is significantly affected by both the speed ratio as well as the axial spacing between the rotors. It was found that with increasing the speed ratio, the strong suction generated by the second rotor, improves the stage pressure rise and stall margin. Lower axial spacing changes the flow incidence to the second rotor and thereby improves the overall performance of the stage. This however, is accompanied by an increased noise level. The performance is investigated at different speed ratios of the rotors at varying axial spacing. Detailed numerical simulations have been conducted using ANSYS CFX13© using mixing plane approach between rotors. Numerical simulations are compared with experimental results at off-design conditions. These results are validated using the experimental data. Numerical simulations are expected to provide deeper insight into the flow physics of contra-rotating rotors which may be difficult to capture experimentally.

Experimental Study on Different Tip Clearance of Low-Speed Axial Fan

2021 ◽  
Author(s):  
Ming Zhang ◽  
Jia Li ◽  
Xu Dong ◽  
Dakun Sun ◽  
Xiaofeng Sun
Keyword(s):  
Experimental Studies ◽  
Pressure Rise ◽  
Rotating Stall ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Signal Spectrum ◽  
Tip Clearance Flow ◽  
Low Speed ◽  
Clearance Flow ◽  
Casing Pressure

Abstract Tip clearance flow is not only the source of undesirable noise but also a potential indicator for critical operating conditions with rotating stall or surge. It can induce blade vibration, which would cause premature blade failure when the vibration is strong enough. The paper presents experimental studies on the effects of tip clearance on the stall inception process in a low-speed high-load single stage fan with different tip clearance. From the point of view of flow range, it has been proved by computations that there is an optimal gap value, and an explanation is given according to different stall mechanisms of large and small tip clearance. However, the experiment of no tip clearance is not easy to achieve. In this experiment, a wearable soft wall casing was used to achieve “zero clearance”, and an explicit conclusion was obtained. The pressure rise and efficiency are improved at small tip clearance. Instantaneous Casing Pressure Field Measurement was carried out: instantaneous casing pressure fields were measured by 9 high response pressure transducers mounted on the casing wall. At the near stall point with large tip clearance, a narrow band increase of the amplitudes in the frequency spectrum at roughly half of the blade passing frequency can be observed according to the spectrum of static pressure at points on the endwall near the leading-edge and above the rotor. This phenomenon was explained from two aspects: tip clearance flow structure and pressure signal spectrum.

Aeromechanical Control of High-Speed Axial Compressor Stall and Engine Performance—Part II: Assessments of Methodology

2013 ◽  
Vol 135 (5) ◽  
Author(s):  
K. L. Coleman ◽  
O. G. McGee, III
Keyword(s):  
Structural Design ◽  
High Speed ◽  
Control Strategies ◽  
Structural Parameters ◽  
Axial Compressor ◽  
Pressure Rise ◽  
Engine Performance ◽  
Rotating Stall ◽  
Tip Clearance ◽  
Low Speed

A theoretical assessment was made explaining how aeromechanical feedback control can be implemented to stabilize rotating stall inception in high-speed axial compression systems. Ten aeromechanical control strategies were quantitatively evaluated based on the control-theoretic formulations and dimensionless performance analysis outlined in the Part I companion paper (McGee and Coleman, 2013, “Aeromechanical Control of High-Speed Axial Compressor Stall and Engine Performance—Part I: Control-Theoretic Models,” ASME J. Fluids Eng., 135(3), p. 031101). The maximum operating range for each aeromechanical control scheme was predicted for optimized structural parameters. Predictability and changeability in the hydrodynamic pressure, temperature, density, operability, and aeromechanical performance of dynamically-compensated, high-speed compressor maps of corrected pressure, corrected mass flow, corrected speeds, temperature ratios, and optimum efficiency were compared for the various aeromechanical control strategies. Compared with dynamically-compensated, low-speed compressor maps of pressure rise and flow coefficient (Gysling and Greitzer, 1995, “Dynamic Control of Rotating Stall in Axial Flow Compressors Using Aeromechanical Feedback,” ASME J. Turbomach., 117(3), pp. 307–319; McGee et al., 2004, “Tailored Structural Design and Aeromechanical Control of Axial Compressor Stall—Part I: Development of Models and Metrics, ASME J. Turbomach, 126(1), pp. 52–62; Fréchette et al., 2004, “Tailored Structural Design and Aeromechanical Control of Axial Compressor Stall—Part II: Evaluation of Approaches,” ASME J. Turbomach., 126(1), pp. 63–72), the present study shows that the most promising aeromechanical designs and controls for a class of high-speed compressors were the use of dynamic fluid injection. Dynamic compensations involving variable duct geometries and dynamically-re-staggered IGV and rotor blades were predicted to yield less controllability under high-speed flow environments. The aeromechanical interaction of a flexible casing wall was predicted to be destabilizing, and thus should be avoided in high-speed compression systems as in low-speed ones by designing sufficiently rigid structures to prevent casing ovalization or other structurally-induced variations in tip clearance.

A theory for rotating stall in contra-rotating fans

2020 ◽  
pp. 095440622096253
Author(s):  
Hossein Khaleghi ◽  
Mohammad Javad Shahriyari ◽  
Martin Heinrich
Keyword(s):  
Single Cell ◽  
Critical Role ◽  
Pressure Rise ◽  
Transient Behavior ◽  
Rotating Stall ◽  
Speed Ratio ◽  
Rotor Speed ◽  
Modified Model ◽  
Stall Cells ◽  
Stagger Angle

This paper reports on a theory of rotating stall in contra-rotating fans and compressors. The theory is developed from Moore’s theory. A second-order hysteresis is used in the current study for the pressure rise of the counter-rotating rows. This enables the model to predict the transient behavior of the stall cell. Comparing the experimental results with the theory shows that the modified model can predict the speed of the stall cells fairly accurately. Results show that the rotor speed ratio plays a critical role in the stall cell speed and its direction of rotation. Furthermore, the developed model makes it possible to study the effects of stagger angle and number of stall cells. The conditions under which pure rotating stall can occur in contra-rotating fans are also discussed in this paper. It is shown that the stall cells merge to form a single cell before a stable fully-developed rotating stall is established.

Aeroacoustic Analysis of Low-Speed Axial Fans With Different Rotational Speeds in the Design Point

2017 ◽  
Author(s):  
Patrick Buchwald ◽  
Damian M. Vogt ◽  
Julien Grilliat ◽  
Wolfgang Laufer ◽  
Michael B. Schmitz ◽  
...  
Keyword(s):  
Flow Separation ◽  
Rotational Speed ◽  
Numerical Study ◽  
Pressure Rise ◽  
Far Field ◽  
Noise Sources ◽  
Blade Loading ◽  
Design Point ◽  
Low Speed ◽  
Axial Fans

One of the main design decisions in the development of low-speed axial fans is the right choice of the blade loading versus rotational speed, since a target pressure rise could either be achieved with a slow spinning fan and high blade loading or a fast spinning fan with less flow turning in the blade passages. Both the blade loading and the fan speed have an influence on the fan performance and the fan acoustics and there is a need to find the optimum choice in order to maximize efficiency while minimizing noise emissions. The present paper addresses this problem by investigating five different fans with the same pressure rise but different rotational speeds in the design point. In the first part of the numerical study, the fan design is described and steady-state Reynolds-averaged Navier-Stokes (RANS) simulations are conducted in order to identify the performance of the fans in the design point and in off-design conditions. The investigations show the existence of an optimum in rotational speed regarding fan efficiency and identify a flow separation on the hub causing a deflection of the outflow in radial direction as the main loss source for slow spinning fans with high blade loadings. Subsequently, Large Eddy Simulations (LES) along with the acoustic analogy of Ffowcs Williams and Hawkings (FW-H) are performed in the design point to identify the main noise sources and to determine the far-field acoustics. The identification of the noise sources within the fans in the near-field is performed with the help of the power spectral density of the pressure. In the far-field, the sound power level is computed using different parts of the fan surface as FW-H sources. Both methods show the same trends regarding noise emissions and allow for a localization of the noise sources. The flow separation on the hub is one of the main noise sources along with the tip vortex with an increase in its strength towards lower rotational speeds and higher loading. Furthermore, a horseshoe vortex detaching from the rotor leading edge and impinging on the pressure side as well as the turbulent boundary layer on the suction side represent significant noise sources. In the present investigation, the maximum in efficiency coincides with the minimum in noise emissions.

CFD - Based Investigation of Effects of Obstruction in Front of Small Axial Cooling Fan and Deterioration of Supply Flow Rate

2021 ◽  
Author(s):  
Tetsushi Fukuda ◽  
Yukio Masuda ◽  
Takashi Fukue ◽  
Yasuhiro Sugimoto ◽  
Tomoyuki Hatakeyama ◽  
...  
Keyword(s):  
Flow Pattern ◽  
Flow Rate ◽  
Pressure Rise ◽  
Leading Edge ◽  
Rotating Stall ◽  
High Density ◽  
Electronic Equipment ◽  
Fan Performance ◽  
Cooling Fan ◽  
High Density Packaging

Abstract This study describes the deterioration of a small axial fan’s supply flow rate in high-density packaging electronic equipment. A cooling fan flow rate can be predicted by its P-Q curve, which shows a relationship between a pressure rise at a fan (ΔP) and a supply flow rate (Q). However, in high-density packaging electronic equipment, the fan performance is affected by the mounting components around the fans, and the accurate prediction of the supply flow rate becomes difficult. This paper tried to do flow visualization around a small axial cooling fan’s impellers when the obstruction was mounted in front of the fan through CFD analysis. A relationship between the supply flow rate by the fan and the flow pattern around the impellers was investigated while changing the distance between the test fan and the obstruction. Through this study, the following results can be obtained. The fan’s flow is stable in the rotating stall region and the higher flow rate operating points regardless of whether or without the obstruction. At the lower flow rate conditions, the formation of a complex unsteady flow is reproduced. As the flow rate decreases, the flow’s separation point becomes closer to the leading edge of the impeller. In the case of obstruction, the change of the flow pattern causes a larger attack angle. As a result, fan performance is degraded.

A Low Speed Axial Compressor With a Cascade of Magnus Rotors to Replace the Aerofoils of the Stator

2004 ◽  
Author(s):  
M. G. Rose
Keyword(s):  
Rotational Speed ◽  
High Speed ◽  
Axial Compressor ◽  
Pressure Rise ◽  
Flow Coefficient ◽  
Recovery Coefficient ◽  
High Rotational Speed ◽  
Aerodynamic Efficiency ◽  
Low Speed ◽  
Conventional Machine

The low speed axial research compressor ‘Rheinfall’ in the Turbomachinery Labs at ETH Zu¨rich has been modified to include a novel stator row. The conventional stator’s vanes have been replaced with a cascade of rotating cylinders or ‘Magnus Rotors’. The initial aim was to demonstrate that such a cascade could reproduce the effect of the aerofoils. This paper gives an overview of the design, experimental results and conclusions drawn from simple modeling of the experiment. The behaviour of the compressor is essentially preserved; the conventional rotor stalls at a slightly higher flow coefficient (φ = 0.4). The pressure rise across the compressor is a function of the cylinder rotational speed. The pressure recovery coefficient Cpr across the stator can be increased by up to 60% compared to the conventional aerofoils with high rotational speed. The stator pressure rise is maintained at much lower flow coefficient (φ = 0.23). Lift coefficients of up to 7.0 have been stably demonstrated. The stator is capable of very high turning (>60°), to axial and beyond. From simple flow modeling the aerodynamic efficiency appears to be about the same as the conventional machine. However, the parasitic losses in the high-speed Magnus spindles double the power absorbed. The recorded characteristics show strong hysteresis across the whole flow range.

Sign in / Sign up

Export Citation Format

Share Document