The Impact of the Human Body Position Changes During Wheelchair Propelling On Motion Resistance Force

Author(s):  
Bartosz Wieczorek ◽  
Lukasz Wargula ◽  
Mateusz Kukla ◽  
Dominik Rybarczyk ◽  
Jan Górecki ◽  
...  

Abstract Purpose - The aim of this research was to analyse the impact of the human body position changes caused by propelling a wheelchair with the pushrim propulsion on the value of motion resistance force. Material and methods - The research was carried out in the group of six persons propelling a wheelchair whose frame was inclined, in respect to the horizontal plain, under the angle of 0°, 7° and 14°. The area of the position variability of the human body centre of gravity and the coefficients of wheelchair rolling resistance have been determined in the research. Results -The results obtained, depending on the wheelchair inclination angle, ranged from 9.82 N to 22.81 N. In addition, it has been determined that the percentage increase in rolling resistance force, with the body position proper for the initial propulsion phase, in relation to the body position for the final propulsion phase, amounted to: 35.6% for the inclination angle of 0°, 43.2% for the inclination angle of 7°, and 48.3% for the inclination angle of 14°. Conclusion - the research done demonstrated the impact of the centre of gravity position change on the change of motion resistance. Thus, the research supplemented knowledge with a new parameter which, like a surface type and wheel type, affects motion resistances.

2013 ◽  
Vol 2013 ◽  
pp. 1-9 ◽  
Author(s):  
Dan B. Marghitu ◽  
Seung Lee

In this study, the experimental and the simulation results for a planar free link impacting a granular medium are analyzed. The resistance force of the granular medium on the body from the moment of the impact until the body stops is very important. Horizontal and vertical static resistance forces developed by theoretical and empirical approaches are considered. The penetrating depth of the impacting end of the free link increases with the increase of the initial impacting velocity. We define the stopping time as the time interval from the moment of impact until the vertical velocity of the link end is zero. The stopping time of the end decreases as the initial velocity increases. The faster the end of the link impacts the surface of the granular medium, the sooner it will come to a stop. This phenomenon involves how rapidly a free link strikes the granular medium and how it slows down upon contact.


Author(s):  
Cécile Fabre

This article examines the impact of medical technologies on the concept of justice and the human body. Traditionally, theories of justice require individuals to transfer material resources to other individuals who are needier or worse off. But three technologies, organ transplantation, genetic engineering, and artificial wombs, have changed our obligations to one another. It appears that justice now requires us to subject our body to sometimes invasive procedures should others need our bodily resources, particular genes, or nutrients which we no longer want to provide through our body itself.


2020 ◽  
Vol 8 (10) ◽  
pp. 686-693
Author(s):  
Manisha A ◽  

One can survive without food but not without water. A human body is comprised of 70% of water which helps in other activities of the body like digestion and metabolic processes. Water is the most critical issue in todays world and its purity is the second. Currently,Watertreatmentmethodsincludefiltrationandheatathightemperaturetokillthebacteria inside it. As a result, consumer demand for water purifier has been increases. Several companies like KENT, HUL, Tata, Eureka Forbes, LG, Bajaj etc. have entered this segment and have launched various brands of water purifiers. Existing demand has also attracted to local players who have entered in the market and assembling water purifiers in minimum cost such as Aqua fres h, Aqua plus, Aqua grand, Aqua care, Aqua pearl, Aqua pure, Liv pro, etc. They vary in size, purification technology, price, color, patterns, usage etc. This study is conducted in Dehradun city a popular tourist place in Uttarakhand. The study mainly aims to analyze the impact of brand preference of respondents on various local water purifiers available in the market. The study also focuses on the consumer behavior towards water purifiers. This research is based on both Primary Survey, 2020 and secondary data. Study finds that, maximum of the respondents is influenced by design and comfortable size of water purifier.


2019 ◽  
Vol 56 (4) ◽  
pp. 831-839
Author(s):  
Emanuela Georgiana Gal-Nadasan ◽  
Norbert Gal-Nadasan ◽  
Dan V. Poenaru ◽  
Dan Surducan ◽  
Diana Popa-Andrei ◽  
...  

At young ages the spinal column, which is the central support system of the human body, is susceptible to malformations, especially if the children are sitting in an incorrect position for long period. Our study examines the case of several elementary school students from a developed rural area. The aim of this study to analyze the impact of long sitting hours (5-6 hours) in incorrect position at on the normal standing up position at elementary school students. The study group for our study consisted of 80 elementary school students were recruited from a local rural elementary school. Each student was evaluated using a Kinect based system to determine their general standing up position. For 14 weeks, twice a week, each student has executed 5 type of Schroth exercises to improve their general body position. The first evaluation has shown that the students general standing up position is affected from the long sitting hours in the school benches. Most of them have shown misalignments at the shoulder and hip levels. In many cases one of the shoulders was higher than the other and the same is true for the hips as well. After 14 weeks of physiotherapy based on Schroth exercises the miss alignments were reduced to a bare minim. The results have shown that long sitting hours in incorrect positions can affect the spinal column and the standing up posture of the human body. In many cases malicious postures start to develop from childhood. If not treated they can transform in hyper-kyphotic and scoliotic postures which can induce other complications. If these malicious postures are observed in early stages of the children and with only 2 hours a week of physiotherapy based on Schroth exercise the postures can be corrected and the hyper-kyphotic and scoliotic postures can be avoided.


2020 ◽  
Vol 7 (3) ◽  
pp. 104-135
Author(s):  
L. Novoselova

In this article, an attempt is made to determine the legal status of the human body (organs and tissue) both while a person is alive and after a person dies. The article discusses the points of view of various authors in relation to the possibility of considering the human body, its organs and tissue, after their separation from the body, as objects of a person’s property rights, and also as an object of a person’s non-property rights. The article argues the impossibility of qualifying the human body and the organs that were not separated from it during life as parts – and perhaps critical parts – of the existence of the total human being, as objects of real (property) rights including the rights of the persons themselves. The human body as a single object is a personal non-property benefit. The organs and tissue separated from the body may be considered objects of real rights, but on several conditions: if they were indeed separated from the body and if the person gave permission for this in a will. The specific characteristics of the legal status of the separated organs and tissue of a human being are analyzed as things (possessions) with limited turnover. The specific characteristics of the legal status of the organs and tissue separated from the body as possessions in limited turnover are reviewed as well as the impact of personal non-property rights on this status. The main focus of the article is on the legal status of the human body and the organs separated from it after death in view of the fact that transplantology and postmortem organ donation are becoming more and more widespread. This issue is analyzed in terms of the body as a whole and as it applies to the organs and tissue that are not used for transplantation. The proposal is to base our analysis on the status of the human body after death which as a rule cannot be the object of property rights. The human body is disposed of within the framework of the protection of the personal non-property rights of the deceased, including the right of physical inviolability that covers the organs and tissue separated from the body. The article characterizes the legal nature of living wills when people give instructions as to the procedure of their burial and other means of handling their body, including donation of their bodies to science. The article examines the possibility of the right of ownership to organs and tissue separated from the body after death. This right can exist if a complex legal construct is present, including a direct or assumed living will of the person. The specific characteristics of living acts concerning the possibility of after-death organ and tissue harvesting for further use, including for transplantation purposes, and the differences between such acts and last wills are determined.


Author(s):  
Inga DABOLINA ◽  
Jelizaveta Fomina ◽  
Eva Lapkovska ◽  
Liene Silina

Correct body posture is a balanced musculoskeletal body position; however, today many people face severe posture defects, and their body posture may be far from a normal, causing progressive musculoskeletal deformities and pain, as well as affecting the functionality and appearance of the body. Human daily habits, lack of physical activities and overall a sedentary lifestyle cause such phenomena. The research focuses on studies of human body measurements and body characteristics while wearing posture-corrective equipment for the assessment of the effectiveness of different posture correctors (abbreviated as PoC). Four test-persons were selected and scanned using 3D anthropometrical scanner in relaxed stand position wearing five different posture correctors for a prolonged period of time in order to determine the effectiveness and functionality of each PoC. Four distance (linear) human body measurements were gained to quantify postural changes - scapula position depth, upper torso position, shoulder projection height and hip-waist depth. General feedbacks on each subject impression of wearing PoCs were also received. Correction of posture could serve as a preventive or treatment for spine-related problems; though, commercially available correctors could negatively affect wearer’s health due to non-conformity of the design and/or used material. Therefore, PoC selection and wearing procedures should be solved with more personalized and customized approaches.


1976 ◽  
Vol 4 (1) ◽  
pp. 3-15 ◽  
Author(s):  
D. J. Schuring

Abstract The concept of rolling resistance force is replaced by that of energy dissipated in unit distance traveled. The energy loss per unit distance, which is a function of slip angle, inclination angle, wheel torque, and other variables, is shown to reach a minimum under driving conditions. The new formula is compared with those given by Gough and by the Society of Automotive Engineers.


Author(s):  
Володимир Петрович Олійник ◽  
Дар’я Вікторівна Теличко

The issues of long-term implants using in the human body are considered. Particular attention is paid to the problem of contactless supply of power to artificial organs with significant energy consumption. Using non-contact energy supply to a fully implanted technical device reduces the risk of infections getting into the patient's body as compared to the use of a power line that is output through internal tissues to the skin surface. The well-known developments of artificial heart apparatus were used as the object of analysis. Their main technical characteristics are considered. The maximum power consumption of these devices is about 20 watts, including models AbioCor. The design of the AbioCor was produced as a fully implanted contactless power unit, but the project was not completed. Although the principle of contactless power supply is undoubtedly an innovative step in the development of implant designs. As a result of the technical implementation of this principle, the following was obtained: it is advisable to use an alternating magnetic field with an inductive coupling between an external and an internal inductor for non-contact energy supply of implants; the use of frequencies of an alternating magnetic field of ~ 100 kHz makes it possible to obtain a compromise solution between the required depth of penetration into biotissues, insignificant heat formation in them and the size and mass of inductors. Under such conditions, the location in the body of the receiving inductor can be determined by medical recommendations. Evaluation experiments were carried out to determine the effective scheme of inclusion of the transmitting and receiving circuits, and the effect on the transmission coefficient of the electrophysical properties of the environment between them. It is shown that for working out of technical solutions of hardware realization of contactless power supply, implantation elements can be placed in saline solution as a model of bioenvironment. It is recommended to use serial element base and circuit solutions used for contactless power supply of radio electronic devices. Also, a quantitative assessment of the additional heat load of the implant on the human body was carried out, since part of the energy of the apparatus and its work, in accordance with the efficiency, inevitably goes into the heat eventually. A simplified calculation of the impact of implant energy losses on the thermal state of the body showed that overheating by 1 °C would be achieved provided the complete insulation of the area, on average, 8.6 hours. This proves the non-critical overheating of the body with implants, and allows the maintenance of a stable body temperature by physiological mechanisms.


2019 ◽  
Vol 2 (1) ◽  
pp. 138-160 ◽  
Author(s):  
Scott Zimmerman ◽  
Russel.J. Reiter

Melatonin is fundamental to the lighting, display, and architectural industries as the primary biomarker used in circadian theory. Billions of dollars are being spent on research, product development, and marketing based on the impact of visible light on melatonin produced by the pineal gland. It has now been shown that the mitochondria produce melatonin in many cells in quantities which are orders of magnitude higher than that produced in the pineal gland. This subcellular melatonin does not necessarily fluctuate with our circadian clock or release into the circulation system, but instead has been proposed to be consumed locally in response to the free radical density within each cell, in particular in response to Near Infrared (NIR) exposure. The main point of this review hypothesizes that the subcellular melatonin is being produced in response to the NIR photons which make up the majority of natural sunlight. Given the number of cells and quantity of subcellular melatonin identified to date, it is reasonable to propose that the body produces and maintains a melatonin reservoir that is separate and apart from the circulatory melatonin generated by the pineal gland. To understand how sunlight may support or stimulate this antioxidant reservoir, it becomes necessary to quantify the free radical density in various parts of the human body. To do this, it is necessary to move away from two-dimensional empirical approaches and develop three-dimensional bio-optical models based on the underlying biological processes at play. Three-dimensional Mechanistic Bio-optical Models (MBM) of the skin, eye, and brain based on non-sequential optical ray tracing and Electron Spin Resonance (ESR) data clearly indicate that the NIR portion of natural sunlight provides the primary stimulus during the day to the majority of the cells in the human body, impacting over 60% of the cells in an adult body and 100% of the cells in the fetus and young children. It is also shown that optically, the human body, under the assumption of natural sunlight, has developed optical mechanisms to gather and localize NIR photons in the most sensitive areas of the human body: blood vessels, retina, brain, skin, and even the fetus.  That assumption is no longer valid in modern societies where the majority of our time is spent exposed to visible only lighting and displays, which emit zero NIR photons. Based on an optical and biological review of the literature and the MBM results, it is proposed that the NIR portion of natural sunlight stimulates an excess of antioxidants in each of our healthy cells and that the cumulative effect of this antioxidant reservoir is to enhance the body’s ability to rapidly and locally deal with changing conditions throughout the day. In this approach the role of circulatory melatonin produced by the pineal gland is to provide an efficient method of delivering supplemental melatonin during periods of low cellular activity and solar stimulus to damaged or aging cells in both diurnal and nocturnal animals. While circulatory melatonin may be the “Hormone of Darkness”, subcellular melatonin may be the “Hormone of Daylight”. 


2018 ◽  
Vol 44 ◽  
pp. 00085 ◽  
Author(s):  
Dariusz Kurz ◽  
Lena Morawska ◽  
Robert Piechota ◽  
Grzegorz Trzmiel

This paper addresses the subject of the building integrated photovoltaics (BIPV). The flexible thin-film CIGS module has been subjected to testing in order to investigate its electrical parameters and the possibilities of adaptation to the building structure. During analysis of performance of the tested building in real conditions, particular attention has been paid to changes in its parameters depending on the inclination angle and the shape of its surface in relation to the incident solar radiation. Current-voltage characteristics and power curves in the selected configuration of module deflections have been analysed. Changing the module’s inclination angle from the optimal 40° to 0° (horizontal arrangement of the module on the ground) reduced the value of generated current (by approx. 26%), voltage increase (by approx. 4%) and output power reduction by approx. 25%. The module generated a lower power compared to the basic test due to the irradiation limit reaching its surface (decrease in the irradiance value of less than 60% from 800 to 330 W/m2). Bending the module at an angle 90° to the ground affected the large unevenness of solar radiation values reaching its surface and even greater losses of generated energy. The values of idle voltage, short-circuit current and voltage in MPP did not change much in relation to the base measurement, however, a large drop in the value of current in MPP was noted, which led to a significant reduction of output power. Thus, the need to strive for the most advantageous exposure of BIPV elements in relation to the sun was demonstrated and the losses on energy yields resulting from the integration of photovoltaic tiles into the body of the building have been estimated.


Sign in / Sign up

Export Citation Format

Share Document