scholarly journals Influence of Pulse Characteristics On Turbocharger Radial Turbine

2021 ◽  
Author(s):  
Roberto Mosca ◽  
ShyangM. Lim ◽  
Mihai Mihaescu
Keyword(s):  
Mass Flow ◽  
Pulse Amplitude ◽  
Pulse Frequency ◽  
Operating Conditions ◽  
System Response ◽  
Primary Parameter ◽  
Temporal Gradient ◽  
Reciprocating Engine ◽  
Turbine Performance ◽  
Pulse Characteristics

Abstract Due to the reciprocating engine, a pulsating flow occurs in the turbine turbocharger, which experiences conditions far from the continuous flow scenario. In this work, the effects of the characteristics of the mass flow pulse, parameterized through amplitude, frequency and temporal gradient, are decoupled and studied via unsteady Computational Fluid Dynamics calculations under on-engine operating conditions. Firstly, the model is validated based on comparisons with experimental data in steady flow conditions. Then, the effect of each parameter on exergy budget is assessed by considering a +/-10% variation with respect to a baseline pulse. The other factors defining the operating conditions (e.g. mass flow, shaft speed and inflow exergy) are kept the same as the baseline. The adopted approach enables to completely isolate the effects of each parameter in contrast with previous literature studies. Based on the results observed, pulse amplitude is identified as the primary parameter affecting the hot-side system response in terms of turbine performance, heat transfer and entropy generation, while frequency and temporal gradient show a smaller influence compared to it. As the pulse amplitude increases, the turbine work is reported to improve up to 9.4%. Smaller variations are observed for the frequency and temporal gradient analysis. With a 10% increase of the pulse frequency the turbine work is registered to improve by 5.0%, while the same percentage reduction of the temporal gradient leads to an increase of turbine work equal to 3.6%.

scholarly journals Turbocharger Radial Turbine Response to Pulse Amplitude

2021 ◽  
pp. 1-15
Author(s):  
Roberto Mosca ◽  
Shyang M. Lim ◽  
Mihai Mihaescu
Keyword(s):  
Heat Transfer ◽  
Viscous Friction ◽  
Pulse Amplitude ◽  
Operating Conditions ◽  
System Response ◽  
Flow Conditions ◽  
Temporal Gradient ◽  
Beneficial Effects ◽  
Turbine Performance ◽  
Radial Turbine

Abstract Under on-engine operating conditions, a turbocharger turbine is subject to a pulsating flow and, consequently, experiences deviations from the performance measured in gas-stand flow conditions. Furthermore, due to the high exhaust gases temperatures, heat transfer further deteriorates the turbine performance. The complex interaction of the aerothermodynamic mechanisms occurring inside the hot-side, and consequently the turbine behavior, is largely affected by the shape of the pulse, which can be parameterized through three parameters: pulse amplitude, frequency, and temporal gradient. This paper investigates the hot-side system response to the pulse amplitude via Detached Eddy Simulations (DES) of a turbocharger radial turbine system including exhaust manifold. Firstly, the computational model is validated against experimental data obtained in gas-stand flow conditions. Then, two different mass flow pulses, characterized by a pulse amplitude difference of 5%, are compared. An exergy-based post-processing approach shows the beneficial effects of increasing the pulse amplitude. An improvement of the turbine power by 1.3%, despite the increment of the heat transfer and total internal irreversibilities by 5.8% and 3.4\%, respectively, is reported. As a result of the higher maximum speeds, internal losses by viscous friction are responsible for the growth of the total internal irreversibilities as pulse amplitude increases.

Turbocharger Radial Turbine Response to Pulse Amplitude

2021 ◽  
Author(s):  
Roberto Mosca ◽  
Shyang Maw Lim ◽  
Mihai Mihaescu
Keyword(s):  
Heat Transfer ◽  
Continuous Flow ◽  
Viscous Friction ◽  
Pulse Amplitude ◽  
Operating Conditions ◽  
System Response ◽  
Maximum Speed ◽  
Detached Eddy Simulation ◽  
Beneficial Effects ◽  
Eddy Simulation

Abstract Under on-engine operating conditions, a turbocharger turbine is subject to a pulsating flow and, consequently, experiences deviations from the performance measured under continuous flow. Furthermore, due to the high exhaust gas temperatures, heat transfer further deteriorates the turbine performance. The complex interaction of the aerothermodynamic mechanisms occurring inside the hot-side, and consequently the turbine behavior, is largely affected by the shape of the pulse, which can be parameterized through three parameters: pulse amplitude, frequency, and temporal gradient. This paper investigates the hot-side system response to the pulse amplitude via a Detached Eddy Simulation (DES) approach of a radial turbocharger turbine system including exhaust manifold. Firstly, the computational model is validated against experimental data obtained under gas stand continuous flow conditions. Then, two different mass flow pulses, characterized by a pulse amplitude difference of ≈ 5%, are compared. An exergy-based post-processing approach shows the beneficial effects of increasing pulse amplitude. An improvement of the turbine power by 1.3%, despite the increment of the heat transfer and total internal irreversibilities by 5.8% and 3.4%, respectively, is reported. As a result of the higher maximum speed, internal losses by viscous friction are responsible for the growth of the total internal irreversibilities as pulse amplitude increases.

Impact of the wastegate opening on radial turbine performance under steady and pulsating flow conditions

2019 ◽  
Vol 234 (2-3) ◽  
pp. 652-668 ◽  
Author(s):  
Ahmed Ketata ◽  
Zied Driss ◽  
Mohamed Salah Abid
Keyword(s):  
Mass Flow ◽  
Large Deviation ◽  
Pulse Frequency ◽  
Pulsating Flow ◽  
Flow Conditions ◽  
One Dimensional ◽  
Loop Area ◽  
Modeling Methodology ◽  
Turbine Performance ◽  
The One

The present article attempts to describe the behavior of wastegated turbines under various steady and pulsating flow conditions. For this, meanline and one-dimensional numerical codes including appropriate modeling approaches for wastegated turbines have been developed with the FORTRAN language. These codes were validated against experiments with an established test rig at the National School of Engineers of Sfax. The discharge coefficient map of the wastegate was determined with a developed correlation built from experiments, and it was served as an input to the developed codes for interpolations during computation. This correlation is based on a two-dimensional non-linear dose-response fitting relationship instead of classical polynomial function which is one novelty of the article in addition to the one-dimensional modeling methodology. The normalized root mean square error (NRMSE) of both cycle-averaged efficiency and mass flow parameter (MFP) remains below 2% which confirms the validity of the proposed calculation approach. The results indicated a large deviation in the turbine performance under pulsating flow conditions compared to the steady state ones. The shape of the hysteresis loop of the turbine efficiency remains unchanged toward the variation of the wastegate valve angle at the same pulse frequency. The mass flow hystereses loop area is decreased by around 50% as the pulse frequency increases from 33 up to 133.33 Hz. An increase of less than 1% of the cycle-averaged efficiency has been reported when the bypass flow through the wastegate increases. The fluctuation of the efficiency is decreased by 1.5% when the wastegate valve becomes fully opened under the whole range of the pulse frequency.

Age alters pulsatile prolactin release: influence of dopaminergic inhibition

1990 ◽  
Vol 258 (5) ◽  
pp. E799-E804
Author(s):  
S. L. Greenspan ◽  
A. Klibanski ◽  
J. W. Rowe ◽  
D. Elahi
Keyword(s):  
Pulse Height ◽  
Pulse Amplitude ◽  
Pulse Frequency ◽  
Prolactin Secretion ◽  
Serum Prolactin ◽  
Dopamine Antagonist ◽  
Elderly Men ◽  
Pulsatile Secretion ◽  
Older Subjects ◽  
Pulse Characteristics

To determine the effect of age on pulsatile prolactin secretion, we examined prolactin pulse characteristics by cluster analysis in healthy young and old male subjects during the day and night. Pulsatile prolactin secretion was identified in all subjects during the day and night, and prolactin pulse frequency remains stable with age. Younger subjects had a significantly higher prolactin pulse amplitude, area, and peak interval during the night compared with older subjects. In contrast, daytime prolactin pulse characteristics were similar in young and old subjects. Because the major neuroregulator of prolactin is dopamine and because normal aging has been reported to be associated with reductions in hypothalamic dopamine content and effect, we determined whether the mechanism of altered day-night prolactin pulsatile secretion was due to changes in dopaminergic tone. We examined endogenous prolactin secretion after administration of the dopamine antagonist metoclopramide. Metoclopramide significantly increased mean serum prolactin concentration and prolactin pulse height and amplitude in all subjects during the day and night. However, net prolactin pulse amplitude after metoclopramide stimulation at night was significantly higher in older subjects compared with younger subjects. We conclude that prolactin pulse amplitude is blunted in elderly men at night and that daytime pulsatile prolactin secretion is unaltered by age in normal men. The mechanism for this alteration of nighttime prolactin pulsatile secretion in elderly men may be due to age-associated changes in dopaminergic regulation.

Treatment system response to transient AOX (adsorbable organic halogen) loadings

1997 ◽  
Vol 35 (2-3) ◽  
pp. 85-91
Author(s):  
D. A. Barton ◽  
J. D. Woodruff ◽  
T. M. Bousquet ◽  
A. M. Parrish
Keyword(s):  
Paper Industry ◽  
Model Development ◽  
Operating Conditions ◽  
System Response ◽  
Additional Information ◽  
Organic Halogen ◽  
Aox Removal ◽  
Variable Operating Conditions ◽  
Plant Shutdown

If promulgated as proposed, effluent guidelines for the U.S. pulp and paper industry will impose average monthly and maximum daily numerical limits of discharged AOX (adsorbable organic halogen). At this time, it is unclear whether the maximum-day variability factor used to establish the proposed effluent guidelines will provide sufficient margin for mills to achieve compliance during periods of normal but variable operating conditions within the pulping and bleaching processes. Consequently, additional information is needed to relate transient AOX loadings with final AOX discharges. This paper presents a simplistic dynamic model of AOX decay during treatment. The model consists of hydraulic characterization of an activated sludge process and a first-order decay coefficient for AOX removal. Data for model development were acquired by frequent collection of influent and effluent samples at a bleach kraft mill during a bleach plant shutdown and startup sequence.

Stability of Ring-Type MEMS Gyroscopes Subjected to Stochastic Angular Speed Fluctuation

2017 ◽  
Vol 139 (4) ◽  
Author(s):  
Samuel F. Asokanthan ◽  
Soroush Arghavan ◽  
Mohamed Bognash
Keyword(s):  
Angular Velocity ◽  
Degrees Of Freedom ◽  
Microelectromechanical Systems ◽  
Damping Ratio ◽  
Operating Conditions ◽  
System Stability ◽  
System Response ◽  
Ring Type ◽  
Mems Gyroscopes ◽  
The Stability

Effect of stochastic fluctuations in angular velocity on the stability of two degrees-of-freedom ring-type microelectromechanical systems (MEMS) gyroscopes is investigated. The governing stochastic differential equations (SDEs) are discretized using the higher-order Milstein scheme in order to numerically predict the system response assuming the fluctuations to be white noise. Simulations via Euler scheme as well as a measure of largest Lyapunov exponents (LLEs) are employed for validation purposes due to lack of similar analytical or experimental data. The response of the gyroscope under different noise fluctuation magnitudes has been computed to ascertain the stability behavior of the system. External noise that affect the gyroscope dynamic behavior typically results from environment factors and the nature of the system operation can be exerted on the system at any frequency range depending on the source. Hence, a parametric study is performed to assess the noise intensity stability threshold for a number of damping ratio values. The stability investigation predicts the form of threshold fluctuation intensity dependence on damping ratio. Under typical gyroscope operating conditions, nominal input angular velocity magnitude and mass mismatch appear to have minimal influence on system stability.

scholarly journals Modelling of Humidity Dynamics for Open-Cathode Proton Exchange Membrane Fuel Cell

2021 ◽  
Vol 12 (3) ◽  
pp. 106
Author(s):  
Fengxiang Chen ◽  
Liming Zhang ◽  
Jieran Jiao
Keyword(s):  
Fuel Cell ◽  
Mass Flow ◽  
Proton Exchange Membrane ◽  
Flow Model ◽  
Transport Theory ◽  
Gas Diffusion ◽  
Proton Exchange ◽  
Operating Conditions ◽  
Output Performance ◽  
Exchange Membrane

The durability and output performance of a fuel cell is highly influenced by the internal humidity, while in most developed models of open-cathode proton exchange membrane fuel cells (OC-PEMFC) the internal water content is viewed as a fixed value. Based on mass and energy conservation law, mass transport theory and electrochemistry principles, the model of humidity dynamics for OC-PEMFC is established in Simulink® environment, including the electrochemical model, mass flow model and thermal model. In the mass flow model, the water retention property and oxygen transfer characteristics of the gas diffusion layer is modelled. The simulation indicates that the internal humidity of OC-PEMFC varies with stack temperature and operating conditions, which has a significant influence on stack efficiency and output performance. In order to maintain a good internal humidity state during operation, this model can be used to determine the optimal stack temperature and for the design of a proper control strategy.

Changes in the characteristics of pulsatile luteinizing hormone secretion during the oestrous cycle and after ovariectomy and oestrogen treatment in female rats

1982 ◽  
Vol 94 (2) ◽  
pp. 177-182 ◽  
Author(s):  
Takashi Higuchi ◽  
Masazumi Kawakami
Keyword(s):  
Hormone Secretion ◽  
Pulse Amplitude ◽  
Pulse Frequency ◽  
Oestrous Cycle ◽  
Female Rats ◽  
Ovariectomized Rats ◽  
Luteinizing Hormone Secretion ◽  
Oestrogen Treatment ◽  
Serum Lh ◽  
Lh Release

Changes in the characteristics of LH secretory pulses in female rats were determined in different hormonal conditions; during the oestrous cycle and after ovariectomy and oestrogen treatment. The frequency and amplitude of the LH pulses were stable during the oestrous cycle except at oestrus when a pattern could not be discerned because of low LH concentrations. These were significantly lower than those measured during other stages of the cycle. Mean LH concentrations and LH pulse amplitudes increased with time up to 30 days after ovariectomy. The frequency of the LH pulse was unchanged 4 days after ovariectomy when mean LH levels had already increased. The frequency increased 10 days after ovariectomy and then remained stable in spite of a further increase in mean serum LH concentrations. Oestradiol-17β injected into ovariectomized rats caused a decrease in LH pulse amplitude but no change in pulse frequency. One day after treatment with oestradiol benzoate no LH pulse was detectable, probably because the amplitude was too small. A generator of pulsatile LH release is postulated and an oestrogen effect on its function is discussed.

scholarly journals Experimental Investigation and Modeling of Inertance Tubes

2005 ◽  
Vol 127 (5) ◽  
pp. 1029-1037 ◽  
Author(s):  
L. O. Schunk ◽  
G. F. Nellis ◽  
J. M. Pfotenhauer
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Acoustic Power ◽  
Operating Conditions ◽  
Thermodynamic Efficiency ◽  
Pulse Tube ◽  
Design Charts ◽  
Wide Range ◽  
Pulse Tube Refrigerators

Growing interest in larger scale pulse tubes has focused attention on optimizing their thermodynamic efficiency. For Stirling-type pulse tubes, the performance is governed by the phase difference between the pressure and mass flow, a characteristic that can be conveniently adjusted through the use of inertance tubes. In this paper we present a model in which the inertance tube is divided into a large number of increments; each increment is represented by a resistance, compliance, and inertance. This model can include local variations along the inertance tube and is capable of predicting pressure, mass flow rate, and the phase between these quantities at any location in the inertance tube as well as in the attached reservoir. The model is verified through careful comparison with those quantities that can be easily and reliably measured; these include the pressure variations along the length of the inertance tube and the mass flow rate into the reservoir. These experimental quantities are shown to be in good agreement with the model’s predictions over a wide range of operating conditions. Design charts are subsequently generated using the model and are presented for various operating conditions in order to facilitate the design of inertance tubes for pulse tube refrigerators. These design charts enable the pulse tube designer to select an inertance tube geometry that achieves a desired phase shift for a given level of acoustic power.

Pulsatile secretion of progesterone from the human corpus luteum: poor correlation with bioactive LH pulses

1986 ◽  
Vol 111 (4) ◽  
pp. 553-557 ◽  
Author(s):  
Inese Z. Beitins ◽  
Maria L. Dufau
Keyword(s):  
Corpus Luteum ◽  
Temporal Relationship ◽  
Pulse Amplitude ◽  
Pulse Frequency ◽  
Biologically Active ◽  
Poor Correlation ◽  
Serum Progesterone ◽  
Progesterone Secretion ◽  
Wide Range ◽  
Human Corpus Luteum

Abstract. Having previously established that biologically active luteinizing hormone (LH) is secreted in episodic pulsations that vary in relation to the menstrual cycle, we investigated the possibility that a temporal relationship could exist between the bioactive LH pulses and progesterone secretion from the late corpus luteum. In 4 young women blood was withdrawn every 15 min for 8 h. Serum progesterone concentrations fluctuated at a mean frequency of 0.9 h with a wide range of amplitudes (13.8 to 1.7 ng/ml). Serum bioactive LH pulse frequency in contrast was 0.25 pulses/h in all subjects. The pulse amplitude was 18.2 to 12.4 mIU/ml (2nd IRP-hMG). These data reveal that within the 8 h-period studied, progesterone secretory pulses occurred four times more frequently as those for bioactive LH. Therefore it is unlikely that a temporal relationship exists between individual bioactive LH and pulses of progesterone secreted by the late corpus luteum.

Sign in / Sign up

Export Citation Format

Share Document