The Dependence of Power Cycles’ Performance on Their Location Relative to the Andrews Curve

1969 ◽  
Author(s):  
C. Casci ◽  
G. Angelino
Keyword(s):  
Heat Transfer ◽  
State Diagram ◽  
Combustion Products ◽  
Industrial Applications ◽  
Working Fluid ◽  
Specific Work ◽  
Closed Cycle ◽  
Working Fluids ◽  
Power Cycles ◽  
Working Media

The adoption of the closed cycle and of working fluids other than steam or air gives the possibility of utilizing for power cycles regions of the temperature-entropy diagram which are inaccessible when the working media are water or combustion products and which enjoy some useful peculiarities. A number of fluids are presented which are suitable for industrial applications and which allow the organization of power cycles covering the liquid, gaseous, and hypercritical regions of the state diagram of a typical substance. Efficiency, specific work, heat transfer surfaces, dimensions of turbomachines, distribution of losses among the various components relating to different fluids and cycles are analyzed and reported. The results strongly support the conclusion that the nature of the working fluid is a powerful tool to adapt the characteristics of power cycles to the widely differing requirements encountered in technical applications.

Performance Analysis and Comparison Study of Transcritical Power Cycles Using CO2-Based Mixtures as Working Fluids

2016 ◽  
Author(s):  
Jiaxi Xia ◽  
Jiangfeng Wang ◽  
Pan Zhao ◽  
Dai Yiping
Keyword(s):  
Critical Temperature ◽  
Parametric Optimization ◽  
Design Parameters ◽  
Working Fluid ◽  
Comparison Study ◽  
Software Environment ◽  
Working Fluids ◽  
Power Cycles ◽  
Power Cycle ◽  
Thermodynamic Performance

CO2 in a transcritical CO2 cycle can not easily be condensed due to its low critical temperature (304.15K). In order to increase the critical temperature of working fluid, an effective method is to blend CO2 with other refrigerants to achieve a higher critical temperature. In this study, a transcritical power cycle using CO2-based mixtures which blend CO2 with other refrigerants as working fluids is investigated under heat source. Mathematical models are established to simulate the transcritical power cycle using different CO2-based mixtures under MATLAB® software environment. A parametric analysis is conducted under steady-state conditions for different CO2-based mixtures. In addition, a parametric optimization is carried out to obtain the optimal design parameters, and the comparisons of the transcritical power cycle using different CO2-based mixtures and pure CO2 are conducted. The results show that a raise in critical temperature can be achieved by using CO2-based mixtures, and CO2-based mixtures with R32 and R22 can also obtain better thermodynamic performance than pure CO2 in transcritical power cycle. What’s more, the condenser area needed by CO2-based mixture is smaller than pure CO2.

Multi-Fluid Gas Turbine Components Scaling for a Generation IV Nuclear Power Plant Performance Simulation

2018 ◽  
Author(s):  
Emmanuel O. Osigwe ◽  
Arnold Gad-Briggs ◽  
Theoklis Nikolaidis ◽  
Pericles Pilidis ◽  
Suresh Sampath
Keyword(s):  
Power Plant ◽  
Nuclear Power Plant ◽  
Gas Turbine ◽  
Nuclear Power ◽  
Working Fluid ◽  
Simulation Tool ◽  
Closed Cycle ◽  
Performance Simulation ◽  
Working Fluids ◽  
Component Map

One major challenge to the accurate development of performance simulation tool for component-based nuclear power plant engine models is the difficulty in accessing component performance maps; hence, researchers or engineers often rely on estimation approach using various scaling techniques. This paper describes a multi-fluid scaling approach used to determine the component characteristics of a closed-cycle gas turbine plant from an existing component map with their design data, which can be applied for different working fluids as may be required in closed-cycle gas turbine operations to adapt data from one component map into a new component map. Each component operation is defined by an appropriate change of state equations which describes its thermodynamic behavior, thus, a consideration of the working fluid properties is of high relevance to the scaling approach. The multi-fluid scaling technique described in this paper was used to develop a computer simulation tool called GT-ACYSS, which can be valuable for analyzing the performance of closed-cycle gas turbine operations with different working fluids. This approach makes it easy to theoretically scale existing map using similar or different working fluids without carrying out a full experimental test or repeating the whole design and development process. The results of selected case studies show a reasonable agreement with available data.

Application of Supercritical Fluids in Thermal- and Nuclear-Power Engineering

2021 ◽  
pp. 601-658
Author(s):  
Igor L. Pioro
Keyword(s):  
Heat Transfer ◽  
Carbon Dioxide ◽  
Supercritical Fluids ◽  
Nuclear Power ◽  
Power Plants ◽  
Thermal Power ◽  
Rankine Cycle ◽  
Working Fluid ◽  
Thermal Power Plants ◽  
Power Cycles

Supercritical Fluids (SCFs) have unique thermophyscial properties and heat-transfer characteristics, which make them very attractive for use in power industry. In this chapter, specifics of thermophysical properties and heat transfer of SCFs such as water, carbon dioxide, and helium are considered and discussed. Also, particularities of heat transfer at Supercritical Pressures (SCPs) are presented, and the most accurate heat-transfer correlations are listed. Supercritical Water (SCW) is widely used as the working fluid in the SCP Rankine “steam”-turbine cycle in fossil-fuel thermal power plants. This increase in thermal efficiency is possible by application of high-temperature reactors and power cycles. Currently, six concepts of Generation-IV reactors are being developed, with coolant outlet temperatures of 500°C~1000°C. SCFs will be used as coolants (helium in GFRs and VHTRs, and SCW in SCWRs) and/or working fluids in power cycles (helium, mixture of nitrogen (80%) and helium (20%), nitrogen and carbon dioxide in Brayton gas-turbine cycles, and SCW/“steam” in Rankine cycle).

scholarly journals Fluid Selection of Transcritical Rankine Cycle for Engine Waste Heat Recovery Based on Temperature Match Method

Energies ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1830
Author(s):  
Zhijian Wang ◽  
Hua Tian ◽  
Lingfeng Shi ◽  
Gequn Shu ◽  
Xianghua Kong ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Specific Heat ◽  
Waste Heat ◽  
Working Fluid ◽  
Exhaust Gas ◽  
Match Method ◽  
Working Fluids ◽  
Cold Source ◽  
Working Fluid Selection ◽  
Transfer Zone

Engines waste a major part of their fuel energy in the jacket water and exhaust gas. Transcritical Rankine cycles are a promising technology to recover the waste heat efficiently. The working fluid selection seems to be a key factor that determines the system performances. However, most of the studies are mainly devoted to compare their thermodynamic performances of various fluids and to decide what kind of properties the best-working fluid shows. In this work, an active working fluid selection instruction is proposed to deal with the temperature match between the bottoming system and cold source. The characters of ideal working fluids are summarized firstly when the temperature match method of a pinch analysis is combined. Various selected fluids are compared in thermodynamic and economic performances to verify the fluid selection instruction. It is found that when the ratio of the average specific heat in the heat transfer zone of exhaust gas to the average specific heat in the heat transfer zone of jacket water becomes higher, the irreversibility loss between the working fluid and cold source is improved. The ethanol shows the highest net power output of 25.52 kW and lowest electricity production cost of $1.97/(kWh) among candidate working fluids.

Fluid Flow and Boiling Heat Transfer in Mini Channels

2010 ◽  
Author(s):  
M. Venkatesan ◽  
M. Aravinthan ◽  
Sarit K. Das ◽  
A. R. Balakrishnan
Keyword(s):  
Heat Transfer ◽  
Fluid Flow ◽  
Boiling Heat Transfer ◽  
Industrial Applications ◽  
Tube Diameter ◽  
Working Fluid ◽  
Phase Flow ◽  
Two Phase ◽  
Mini Channels ◽  
Micro Propulsion

Two phase flows in mini channels occur in many industrial applications such as electronic cooling, compact heat exchangers, compact refrigeration systems and in micro propulsion devices. Due to its significance, research on two phase flow in mini channels has become attractive. However, in recent times a controversy exists whether flow in minichannel is different from macro flow because there are still substantial disagreements among various experimental results. In the present study an experimental investigation is carried out for fluid flow and boiling heat transfer characteristics of mini channels with tube diameters ranging from 1–3mm. The tubes were made of SS with water as the working fluid. The variation in friction factor and Nusselt number with decrease in tube diameter for single phase flow was systematically studied. The point of Onset of Nucelate Boiling (ONB) was identified based on wall temperature profile. The effect of heat flux and mass flux on two phase pressure drop with three different tube diameters during sub cooled boiling were investigated. The results reveal that there is an unmistakable effect of tube diameter on fluid friction and onset of boiling during sub cooled boiling in tubes of mini channel dimensions.

Creep Rupture Behavior of Selected Turbine Materials in Air, Ultra-High Purity Helium, and Simulated Closed Cycle Brayton Helium Working Fluids

1981 ◽  
Vol 103 (2) ◽  
pp. 331-337 ◽  
Author(s):  
R. L. Ammon ◽  
L. R. Eisenstatt ◽  
G. O. Yatsko
Keyword(s):  
High Purity ◽  
Creep Rupture ◽  
Working Fluid ◽  
Closed Cycle ◽  
Working Fluids ◽  
Ultra High Purity ◽  
Rupture Properties ◽  
Rupture Behavior

Five turbine materials, IN100, 713LC, MAR-M-509, MA-754 and TZM were selected as candidate materials for use in a Compact Closed Cycle Brayton System (CCCBS) study in which helium served as the working fluid. The suitability of the alloys to serve in the CCCBS environment at 927 C (1700 F) was evaluated on the basis of creep-rupture tests conducted in air, ultra-high purity helium (>99.9999 percent), and a controlled impurity helium environment. Baseline reference creep rupture properties for times up to 10,000 hr were established in a static ultra-high purity helium environment.

A Systematic Comparison and Multi-Objective Optimisation of Humid Power Cycles: Part II—Economics

2008 ◽  
Author(s):  
Ronan M. Kavanagh ◽  
Geoffrey T. Parks
Keyword(s):  
Power Systems ◽  
Gas Turbine ◽  
Search Algorithm ◽  
Working Fluid ◽  
Specific Work ◽  
Power Cycles ◽  
System Parameters ◽  
Multi Objective ◽  
Fluid Properties ◽  
The Impact

The STIG, HAT and TOPHAT cycles lie at the centre of the debate on which humid power cycle will deliver optimal performance when applied to an aero-derivative gas turbine and, indeed, when such cycles will be implemented. Of these humid cycles, it has been claimed that the TOPHAT cycle has the highest efficiency and specific work, followed closely by the HAT (Humid Air Turbine) and then the STIG (STeam Injected Gas turbine) cycle. In this study, the systems have been simulated using consistent thermodynamic and economic models for the components and working fluid properties, allowing a consistent and non-biased appraisal of these systems. Part 1 of these two papers focussed on the thermodynamic performance and the impact of the system parameters on the performance, part 2 studies the economic performance of these cycles. The three humid power systems and up to ten system parameters are optimised using a multi-objective Tabu Search algorithm, developed in the Cambridge Engineering Design Centre.

scholarly journals A Review on the Thermal-Hydraulic Performance and Optimization of Compact Heat Exchangers

Energies ◽  
2021 ◽  
Vol 14 (19) ◽  
pp. 6056
Author(s):  
Gaoliang Liao ◽  
Zhizhou Li ◽  
Feng Zhang ◽  
Lijun Liu ◽  
Jiaqiang E
Keyword(s):  
Heat Transfer ◽  
Performance Evaluation ◽  
Heat Exchangers ◽  
Industrial Applications ◽  
Working Fluids ◽  
Evaluation Indexes ◽  
Compact Heat Exchangers ◽  
Printed Circuit ◽  
Different Types ◽  
Selection Of

Heat exchangers play an important role in power, the chemical industry, petroleum, food and many other industrial productions, while compact heat exchangers are more favored in industrial applications due to their high thermal efficiency and small size. This paper summarizes the research status of different types of compact heat exchangers, especially the research results of heat transfer and pressure drop of printed circuit heat exchangers, so that researchers can have an overall understanding of the development of compact heat exchangers and get the required information quickly. In addition, this paper summarizes and analyzes several main working fluids selected in compact heat exchangers, and puts forward some discussions and suggestions on the selection of working fluids. Finally, according to the existing published literature, the performance evaluation indexes of compact heat exchangers are summarized and compared, which is convenient for developers and researchers to better grasp the design direction.

scholarly journals Investigation of heat transfer enhancement in an annular conduit with angled fins using functionalized GNP colloidal suspension

2021 ◽  
Vol 945 (1) ◽  
pp. 012058
Author(s):  
Sayshar Ram Nair ◽  
Cheen Sean Oon ◽  
Ming Kwang Tan ◽  
S.N. Kazi
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Heat Exchanger ◽  
Heat Exchangers ◽  
Power Plants ◽  
Colloidal Suspension ◽  
Industrial Applications ◽  
Point Of View ◽  
Solid Particles ◽  
Working Fluid

Abstract Heat exchangers are important equipment with various industrial applications such as power plants, HVAC industry and chemical industries. Various fluids that are used as working fluid in the heat exchangers such as water, oil, and ethylene glycol. Researchers have conducted various studies and investigations to improve the heat exchanger be it from material or heat transfer point of view. There have been attempts to create mixtures with solid particles suspended. This invention had some drawbacks since the pressure drop was compromised, on top of the occurrence of sedimentation or even erosion, which incurs higher maintenance costs. A new class of colloidal suspension fluid that met the demands and characteristics of a heat exchanger was then created. This novel colloidal suspension mixture was then and now addressed as “nanofluid”. In this study, the usage of functionalized graphene nanoplatelet (GNP) nanofluids will be studied for its thermal conductivity within an annular conduit with angled fins, which encourage swirling flows. The simulation results for the chosen GNP nanofluid concentrations have shown an enhancement in thermal conductivity and heat transfer coefficient compared to the corresponding base fluid thermal properties. The data from this research is useful in industrial applications which involve heat exchangers with finned tubes.

Design and Operational Challenges of Switching Working Fluid for a Gen IV Nuclear Powered Closed-Cycle Gas Turbine: Case Studies of Nitrogen and Air, Helium and Argon

2020 ◽  
Author(s):  
Emmanuel O. Osigwe ◽  
Arnold Gad-Briggs ◽  
Nasiru Tukur ◽  
Pericles Pilidis
Keyword(s):  
Gas Turbine ◽  
Case Studies ◽  
Nuclear Power ◽  
Cycle Performance ◽  
Working Fluid ◽  
Closed Cycle ◽  
Working Fluids ◽  
First Case ◽  
Gen Iv

Abstract A unique benefit of using the closed-cycle gas turbine and gas turbomachines employed in the Gen-IV nuclear power plant is the flexibility it offers in terms of working fluid usage. This is so because of the self-containing nature of the closed-cycle gas turbine. To this end, the selection of the working fluid for the cycle operation is driven by several factors such as the cycle performance, system design, and component material compatibility with fluid properties, availability, and many more. This paper provides an understanding of the design and operational challenges of switching working fluids for a nuclear powered closed-cycle gas turbine. Using the plant output power of a simple closed-cycle configuration as a baseline condition, two case studies have been presented in this paper to explore the design and operational challenges of switching working fluids. In the first case study, the fluid was switched from nitrogen to air and in the second case study, helium and argon were utilised. In both cases, using thermodynamic flow relationship, the closed-cycle gas turbine turbomachinery components maps were analysed to understand the operational requirements for switching the working fluids. The paper also provided an insight into the turbomachinery component design considerations for this to be achieved. The overarching results from a thermodynamic perspective showed fluids with similar thermodynamic behaviour could be switched during idle synchronous speed.

Sign in / Sign up

Export Citation Format

Share Document