Hybrid Catalytic Combustion for Stationary Gas Turbine: Concept and Small Scale Test Results

1987 ◽  
Author(s):  
Tomiaki Furuya ◽  
Terunobu Hayata ◽  
Susumu Yamanaka ◽  
Junji Koezuka ◽  
Toshiyuki Yoshine ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Phase ◽  
Gas Turbines ◽  
Catalytic Combustion ◽  
Small Scale ◽  
Inlet Temperature ◽  
Test Results ◽  
Turbine Inlet Temperature ◽  
Scale Test ◽  
Near Future

Catalytic combustion for gas turbine applications has been investigated. Its significant advantages in reducing combustor emissions, particularly nitrogen oxides (NOx), have been shown. One of the main problems in regard to developing a catalytic combustor is the durability of catalysts, because the catalysts deteriorate during high temperature operation, which is normal for current gas turbines and near future gas turbines. The hybrid catalytic combustion concept has advantages concerned with catalyst durability. This paper shows its concept and small scale test results. This hybrid catalytic combustion concept comprises the following steps; premix fuel and air for a catalyst-packed zone; operate catalysts at rather low temperatures, to prolong catalyst life; add fresh fuel into the stream at the catalyst-packed zone outlet, where gas phase combustion occurs completely without a catalyst; add dilution air into the stream at the gas phase combustion zone outlet with a by-pass valve. Experimental data and analyses indicated that this hybrid catalytic combustion has a potential of being applicable to current gas turbines (turbine inlet temperature is about 1100°C) and near future gas turbines (turbine inlet temperature is about 1300°C).

Development and Fabrication of Silicon Nitride Components for Ceramic Gas Turbine

1997 ◽  
Author(s):  
Keisuke Makino ◽  
Ken-Ichi Mizuno ◽  
Toru Shimamori
Keyword(s):  
High Temperature ◽  
Silicon Nitride ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Turbine Blades ◽  
High Strength ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Spark Plug ◽  
Power Turbine

NGK Spark Plug Co., Ltd. has been developing various silicon nitride materials, and the technology for fabricating components for ceramic gas turbines (CGT) using theses materials. We are supplying silicon nitride material components for the project to develop 300 kW class CGT for co-generation in Japan. EC-152 was developed for components that require high strength at high temperature, such as turbine blades and turbine nozzles. In order to adapt the increasing of the turbine inlet temperature (TIT) up to 1,350 °C in accordance with the project goals, we developed two silicon nitride materials with further unproved properties: ST-1 and ST-2. ST-1 has a higher strength than EC-152 and is suitable for first stage turbine blades and power turbine blades. ST-2 has higher oxidation resistance than EC-152 and is suitable for power turbine nozzles. In this paper, we report on the properties of these materials, and present the results of evaluations of these materials when they are actually used for CGT components such as first stage turbine blades and power turbine nozzles.

Three Spool High Efficiency Small Scale Gas Turbine Concept

2017 ◽  
Author(s):  
Matti Malkamäki ◽  
Ahti Jaatinen-Värri ◽  
Antti Uusitalo ◽  
Aki Grönman ◽  
Juha Honkatukia ◽  
...  
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Gas Turbines ◽  
High Efficiency ◽  
Small Scale ◽  
Inlet Temperature ◽  
Substantial Impact ◽  
Electrical Efficiency ◽  
Partial Load ◽  
Reciprocating Engines

Decentralized electricity and heat production is a rising trend in small-scale industry. There is a tendency towards more distributed power generation. The decentralized power generation is also pushed forward by the policymakers. Reciprocating engines and gas turbines have an essential role in the global decentralized energy markets and improvements in their electrical efficiency have a substantial impact from the environmental and economic viewpoints. This paper introduces an intercooled and recuperated three stage, three-shaft gas turbine concept in 850 kW electric output range. The gas turbine is optimized for a realistic combination of the turbomachinery efficiencies, the turbine inlet temperature, the compressor specific speeds, the recuperation rate and the pressure ratio. The new gas turbine design is a natural development of the earlier two-spool gas turbine construction and it competes with the efficiencies achieved both with similar size reciprocating engines and large industrial gas turbines used in heat and power generation all over the world and manufactured in large production series. This paper presents a small-scale gas turbine process, which has a simulated electrical efficiency of 48% as well as thermal efficiency of 51% and can compete with reciprocating engines in terms of electrical efficiency at nominal and partial load conditions.

Rolls Royce/Allison 501-K Gas Turbine Anti-Fouling Compressor Coatings Evaluation

2002 ◽  
Author(s):  
Daniel E. Caguiat
Keyword(s):  
Gas Turbine ◽  
Fuel Consumption ◽  
Gas Turbines ◽  
Performance Degradation ◽  
Specific Fuel Consumption ◽  
Inlet Temperature ◽  
Test Results ◽  
Turbine Inlet ◽  
Compressor Performance ◽  
Compressor Efficiency

The Naval Surface Warfare Center, Carderock Division (NSWCCD) Gas Turbine Emerging Technologies Code 9334 was tasked by NSWCCD Shipboard Energy Office Code 859 to research and evaluate fouling resistant compressor coatings for Rolls Royce Allison 501-K Series gas turbines. The objective of these tests was to investigate the feasibility of reducing the rate of compressor fouling degradation and associated rate of specific fuel consumption (SFC) increase through the application of anti-fouling coatings. Code 9334 conducted a market investigation and selected coatings that best fit the test objective. The coatings selected were Sermalon for compressor stages 1 and 2 and Sermaflow S4000 for the remaining 12 compressor stages. Both coatings are manufactured by Sermatech International, are intended to substantially decrease blade surface roughness, have inert top layers, and contain an anti-corrosive aluminum-ceramic base coat. Sermalon contains a Polytetrafluoroethylene (PTFE) topcoat, a substance similar to Teflon, for added fouling resistance. Tests were conducted at the Philadelphia Land Based Engineering Site (LBES). Testing was first performed on the existing LBES 501-K17 gas turbine, which had a non-coated compressor. The compressor was then replaced by a coated compressor and the test was repeated. The test plan consisted of injecting a known amount of salt solution into the gas turbine inlet while gathering compressor performance degradation and fuel economy data for 0, 500, 1000, and 1250 KW generator load levels. This method facilitated a direct comparison of compressor degradation trends for the coated and non-coated compressors operating with the same turbine section, thereby reducing the number of variables involved. The collected data for turbine inlet, temperature, compressor efficiency, and fuel consumption were plotted as a percentage of the baseline conditions for each compressor. The results of each plot show a decrease in the rates of compressor degradation and SFC increase for the coated compressor compared to the non-coated compressor. Overall test results show that it is feasible to utilize anti-fouling compressor coatings to reduce the rate of specific fuel consumption increase associated with compressor performance degradation.

Expanding Fuel Flexibility in MHPS’ Dry Low NOx Combustor

2018 ◽  
Author(s):  
Katsuyoshi Tada ◽  
Kei Inoue ◽  
Tomo Kawakami ◽  
Keijiro Saitoh ◽  
Satoshi Tanimura
Keyword(s):  
Power Systems ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Environmental Conservation ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Social Perspectives ◽  
Turbine Inlet ◽  
Fuel Flexibility

Gas-turbine combined-cycle (GTCC) power generation is clean and efficient, and its demand will increase in the future from economic and social perspectives. Raising turbine inlet temperature is an effective way to increase combined cycle efficiency and contributes to global environmental conservation by reducing CO2 emissions and preventing global warming. However, increasing turbine inlet temperature can lead to the increase of NOx emissions, depletion of the ozone layer and generation of photochemical smog. To deal with this issue, MHPS (MITSUBISHI HITACHI POWER SYSTEMS) and MHI (MITSUBISHI HEAVY INDUSTRIES) have developed Dry Low NOx (DLN) combustion techniques for high temperature gas turbines. In addition, fuel flexibility is one of the most important features for DLN combustors to meet the requirement of the gas turbine market. MHPS and MHI have demonstrated DLN combustor fuel flexibility with natural gas (NG) fuels that have a large Wobbe Index variation, a Hydrogen-NG mixture, and crude oils.

Recent Advances of Internal Cooling Techniques for Gas Turbine Airfoils

2013 ◽  
Vol 5 (2) ◽  
Author(s):  
Minking K. Chyu ◽  
Sin Chien Siw
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Energy Demand ◽  
Major Elements ◽  
Inlet Temperature ◽  
Internal Cooling ◽  
Performance Goal ◽  
Turbine Inlet Temperature ◽  
Air Breathing ◽  
Turbine Inlet

The performance goal of modern gas turbine engines, both land-base and air-breathing engines, can be achieved by increasing the turbine inlet temperature (TIT). The level of TIT in the near future can reach as high as 1700 °C for utility turbines and over 1900 °C for advanced military engines. Advanced and innovative cooling techniques become one of the crucial major elements supporting the development of modern gas turbines, both land-based and air-breathing engines with continual increment of turbine inlet temperature (TIT) in order to meet higher energy demand and efficiency. This paper discusses state-of-the-art airfoil cooling techniques that are mainly applicable in the mainbody and trailing edge section of turbine airfoil. Potential internal cooling designs for near-term applications based on current manufacturing capabilities are identified. A literature survey focusing primarily on the past four to five years has also been performed.

scholarly journals Development of a Catalytic Combustor for a Heavy-Duty Utility Gas Turbine

1996 ◽  
Author(s):  
Ralph A. Dalla Betta ◽  
James C. Schlatter ◽  
Sarento G. Nickolas ◽  
Martin B. Cutrone ◽  
Kenneth W. Beebe ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Catalytic Combustion ◽  
Full Scale ◽  
Inlet Temperature ◽  
Nox Emissions ◽  
Combustion System ◽  
Catalytic Reactor ◽  
Heavy Duty ◽  
Catalytic Combustor

The most effective technologies currently available for controlling NOx emissions from heavy-duty industrial gas turbines are either diluent injection in the combustor reaction zone, or lean premixed Dry Low NOx (DLN) combustion. For ultra low emissions requirements, these must be combined with selective catalytic reduction (SCR) DeNOx systems in the gas turbine exhaust. An alternative technology for achieving comparable emissions levels with the potential for lower capital investment and operating cost is catalytic combustion of lean premixed fuel and air within the gas turbine. The design of a catalytic combustion system using natural gas fuel has been prepared for the GE model MS9OOIE gas turbine. This machine has a turbine inlet temperature to the first rotating stage of over 1100°C and produces approximately 105 MW electrical output in simple cycle operation. The 508 mm diameter catalytic combustor designed for this gas turbine was operated at full-scale conditions in tests conducted in 1992 and 1994. The combustor was operated for twelve hours during the 1994 test and demonstrated very low NOx emissions from the catalytic reactor. The total exhaust NOx level was approximately 12–15 ppmv and was produced almost entirely in the preburner ahead of the reactor. A small quantity of steam injected into the preburner reduced the NOx emissions to 5–6 ppmv. Development of the combustion system has continued with the objectives of reducing CO and UHC emissions, understanding the parameters affecting reactor stability and spatial non-uniformities which were observed at low inlet temperature, and improving the structural integrity of the reactor system to a level required for commercial operation of gas turbines. Design modifications were completed and combustion hardware was fabricated for additional full-scale tests of the catalytic combustion system in March 1995 and January 1996. This paper presents a discussion of the combustor design, the catalytic reactor design and the results of full-scale testing of the improved combustor at MS9OOIE cycle conditions in the March 1995 and January 1996 tests. Major improvements in performance were achieved with CO and UHC emissions of 10 ppmv and 0 ppmv at base load conditions. This ongoing program will lead to two additional full-scale combustion system tests in 1996. The results of these tests will be available for discussion at the June 1996 Conference in Birmingham.

scholarly journals 100s and 1000s Mw Open and Semi-Closed Cycle Gas Turbines for Base and Peak Operation

1974 ◽  
Author(s):  
V. V. Uvarov ◽  
V. S. Beknev ◽  
E. A. Manushin
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Simple Cycle ◽  
Inlet Temperature ◽  
Closed Cycle ◽  
Turbine Inlet Temperature ◽  
Unit Capacity ◽  
Temperature And Pressure ◽  
Different Levels

There are two different approaches to develop the gas turbines for power. One can get some megawatts by simple cycle or by more complex cycle units. Both units require very different levels of turbine inlet temperature and pressure ratio for the same unit capacity. Both approaches are discussed. These two approaches lead to different size and efficiencies of gas turbine units for power. Some features of the designing problems of such units are discussed.

Status of the Automotive Ceramic Gas Turbine Development Progrem: Year Four Progress

1995 ◽  
Author(s):  
Tsubura Nishiyama ◽  
Masumi Iwai ◽  
Norio Nakazawa ◽  
Masafumi Sasaki ◽  
Haruo Katagiri ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Inlet Temperature ◽  
Rotor Speed ◽  
Turbine Inlet Temperature ◽  
Turbine Engine ◽  
Turbine Inlet ◽  
Basic Engine ◽  
Energy Center ◽  
Engine Components

The seven-year program, designated “Research & Development of Automotive Ceramic Gas Turbine Engine (CGT Program)”, was started in 1990 with the object of demonstrating the advantageous potentials of ceramic gas turbines for automotive use. This CGT Program is conducted by Petroleum Energy Center. The basic engine is a 100kW, single-shaft regenerative engine having turbine inlet temperature of 1350°C and rotor speed of 110000rpm. In the forth year of the program, the engine components were experimentally evaluated and improved in the various test rigs, and the first assembly test including rotating and stationary components, was performed this year under the condition of turbine inlet temperature of 1200°C.

scholarly journals Exergy Efficiency Optimization for Gas Turbine Based Cogeneration Systems

2013 ◽  
Author(s):  
Ana C. Ferreira ◽  
Senhorinha F. Teixeira ◽  
José C. Teixeira ◽  
Manuel L. Nunes ◽  
Luís B. Martins
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Exergy Analysis ◽  
Exergy Efficiency ◽  
Plant Performance ◽  
System Component ◽  
Inlet Temperature ◽  
Exergy Destruction ◽  
Turbine Inlet Temperature ◽  
Turbine Inlet

Energy degradation can be calculated by the quantification of entropy and loss of work and is a common approach in power plant performance analysis. Information about the location, amount and sources of system deficiencies are determined by the exergy analysis, which quantifies the exergy destruction. Micro-gas turbines are prime movers that are ideally suited for cogeneration applications due to their flexibility in providing stable and reliable power. This paper presents an exergy analysis by means of a numerical simulation of a regenerative micro-gas turbine for cogeneration applications. The main objective is to study the best configuration of each system component, considering the minimization of the system irreversibilities. Each component of the system was evaluated considering the quantitative exergy balance. Subsequently the optimization procedure was applied to the mathematical model that describes the full system. The rate of irreversibility, efficiency and flaws are highlighted for each system component and for the whole system. The effect of turbine inlet temperature change on plant exergy destruction was also evaluated. The results disclose that considerable exergy destruction occurs in the combustion chamber. Also, it was revealed that the exergy efficiency is expressively dependent on the changes of the turbine inlet temperature and increases with the latter.

Redesign of the TG20 Heavy-Duty Gas Turbine to Increase Turbine Inlet Temperature and Global Efficiency

2020 ◽  
Author(s):  
Mirko Baratta ◽  
Francesco Cardile ◽  
Daniela Anna Misul ◽  
Nicola Rosafio ◽  
Simone Salvadori ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Coolant Fluid ◽  
Specific Power ◽  
Inlet Temperature ◽  
Heavy Duty ◽  
Turbine Inlet Temperature ◽  
Rotating Blade ◽  
Turbine Inlet ◽  
Heavy Duty Gas Turbine

Abstract The even more stringent limitations set by the European Commission on pollutant emissions are forcing gas turbine manufacturers towards the redesign of the most important components to increase efficiency and specific power. Current trends in gas turbine design include an increased attention to the design of cooling systems and enhanced best practices for the study of components interaction. At the same time, the recent crisis suffered by the oil and gas industry reduced the interest in brand new gas turbines, thus increasing the service market. Therefore, original equipment manufacturers would rather propose the replacement of specific components within the gas turbine plant during its maintenance with compatible elements that are likely to guarantee increased performance and longer residual lifetime at a more desirable nominal working point. In the present activity the cooling system of the TG20 heavy-duty gas turbine has been redesigned to increase the turbine inlet temperature while contemporaneously reducing the total amount of coolant mass-flow. Specifically, the cooling scheme of the rotating blade of the first turbine row has been reviewed at the Department of Energy (DENERG) of Politecnico di Torino in cooperation with EthosEnergy Italia S.p.a.. The paper presents a new design, which, starting from the original solution featuring fifteen smooth pipes, adopts an improved geometry characterized by the presence of turbulators. The activity has been carried out using Computational Fluid Dynamics (CFD) for the coolant/blade interaction and one-dimensional models developed at EthosEnergy for the redistribution of the cooling flows in the cavities. The mutual effects between the coolant fluid and the blade are analyzed using a Conjugate Heat Transfer (CHT) approach with Star-CCM+. The validation of the computational approach has been performed exploiting the experimental data available for the NASA C3X test case. The TG20 rotating blade of the first turbine row has been analyzed considering the two different coolant configurations. The impact of the main flow on the thermal field has initially been included by imposing a temperature field on the blade surface. The latter field has in turn been obtained by means of a separate computation for the solid only. Full CHT simulations has hence been performed, thus quantifying the accuracy of the proposed approach. The obtained results are discussed in terms of thermo-fluid-dynamic effects.

Sign in / Sign up

Export Citation Format

Share Document