scholarly journals An Algebraic Method to Check the Singularity-Free Paths for Parallel Robots

2015 ◽  
Author(s):  
R. Jha ◽  
D. Chablat ◽  
F. Rouillier ◽  
G. Moroz
Keyword(s):  
Degrees Of Freedom ◽  
Complex Shape ◽  
Algebraic Method ◽  
Parallel Manipulators ◽  
Parallel Robot ◽  
Joint Space ◽  
Parallel Robots ◽  
Singular Configuration ◽  
End Effectors ◽  
Three Degrees Of Freedom

Trajectory planning is a critical step while programming the parallel manipulators in a robotic cell. The main problem arises when there exists a singular configuration between the two poses of the end-effectors while discretizing the path with a classical approach. This paper presents an algebraic method to check the feasibility of any given trajectories in the workspace. The solutions of the polynomial equations associated with the trajectories are projected in the joint space using Gröbner based elimination methods and the remaining equations are expressed in a parametric form where the articular variables are functions of time t unlike any numerical or discretization method. These formal computations allow to write the Jacobian of the manipulator as a function of time and to check if its determinant can vanish between two poses. Another benefit of this approach is to use a largest workspace with a more complex shape than a cube, cylinder or sphere. For the Orthoglide, a three degrees of freedom parallel robot, three different trajectories are used to illustrate this method.

Performing Nonsingular Transitions Between Assembly Modes in Analytic Parallel Manipulators by Enclosing Quadruple Solutions

2015 ◽  
Vol 137 (12) ◽  
Author(s):  
Adrián Peidró ◽  
José María Marín ◽  
Arturo Gil ◽  
Óscar Reinoso
Keyword(s):  
Degrees Of Freedom ◽  
Parallel Manipulators ◽  
Joint Space ◽  
Parallel Robots ◽  
Forward Kinematics ◽  
Characteristic Polynomials ◽  
Forward Kinematic ◽  
Three Degrees Of Freedom

This paper analyzes the multiplicity of the solutions to forward kinematics of two classes of analytic robots: 2RPR-PR robots with a passive leg and 3-RPR robots with nonsimilar flat platform and base. Since their characteristic polynomials cannot have more than two valid roots, one may think that triple solutions, and hence nonsingular transitions between different assembly modes, are impossible for them. However, the authors show that the forward kinematic problems of these robots always admit quadruple solutions and obtain analytically the loci of points of the joint space where these solutions occur. Then, it is shown that performing trajectories in the joint space that enclose these points can produce nonsingular transitions, demonstrating that it is possible to design simple analytic parallel robots with two and three degrees-of-freedom (DOF) and the ability to execute these transitions.

DeltaBot: A New Cable-Based Ultra High Speed Robot

2003 ◽  
Author(s):  
Saeed Behzadipour ◽  
Robert Dekker ◽  
Amir Khajepour ◽  
Edmon Chan
Keyword(s):  
High Speed ◽  
Degrees Of Freedom ◽  
Manufacturing Industry ◽  
Design Procedure ◽  
Parallel Manipulators ◽  
Parallel Robot ◽  
Parallel Robots ◽  
Manufacturing Cost ◽  
End Effector ◽  
Serial Manipulators

The growing needs for high speed positioning devices in the automated manufacturing industry have been challenged by robotic science for more than two decades. Parallel manipulators have been widely used for this purpose due to their advantage of lower moving inertia over the conventional serial manipulators. Cable actuated parallel robots were introduced in 1980’s to reduce the moving inertia even further. In this work, a new cable-based parallel robot is introduced. For this robot, the cables are used not only to actuate the end-effector but also to apply the necessary kinematic constraints to provide three pure translational degrees of freedom. In order to maintain tension in the cables, a passive air cylinder is used to push the end-effector against the stationary platform. In addition to low moving inertia, the new design benefits from simplicity and low manufacturing cost by eliminating joints from the robot’s mechanism. The design procedure and the results of experiments will be discussed in the following.

Fully-Isotropic T1R2-Type Parallel Robots With Three Degrees of Freedom

2005 ◽  
Author(s):  
Grigore Gogu
Keyword(s):  
Degrees Of Freedom ◽  
Jacobian Matrix ◽  
Parallel Manipulators ◽  
Parallel Robots ◽  
Velocity Space ◽  
Linear Transformations ◽  
Matrix Mapping ◽  
Joint Velocity ◽  
First Time ◽  
Three Degrees Of Freedom

The paper presents singularity-free fully-isotropic T1R2-type parallel manipulators (PMs) with three degrees of freedom. The mobile platform has one independent translation (T1) and two rotations (R2). A method is proposed for structural synthesis of fully-isotropic T1R2-type PMs based on the theory of linear transformations. A one-to-one correspondence exists between the actuated joint velocity space and the external velocity space of the moving platform. The Jacobian matrix mapping the two vector spaces of fully-isotropic T1R2-type PMs presented in this paper is the 3x3 identity matrix throughout the entire workspace. The condition number and the determinant of the Jacobian matrix being equal to one, the manipulator performs very well with regard to force and motion transmission capabilities. As far as we are aware, this paper presents for the first time in the literature solutions of singularity-free T1R2-type PMs with decoupled an uncoupled motions, along with the fully-isotropic solutions.

The QuadroG Robot, a Parallel Robot With a Configurable Platform for Haptic Applications

2015 ◽  
Author(s):  
Salua Hamaza ◽  
Patrice Lambert ◽  
Marco Carricato ◽  
Just Herder
Keyword(s):  
Kinematic Analysis ◽  
Degrees Of Freedom ◽  
Closed Loop ◽  
Parallel Robot ◽  
Parallel Robots ◽  
End Effector ◽  
Contact Points ◽  
Loop Chain ◽  
End Effectors ◽  
4 Degrees Of Freedom

This paper explores the fundamentals of parallel robots with configurable platforms (PRCP), as well as the design and the kinematic analysis of those. The concept behind PRCP is that the rigid (non-configurable) end-effector is replaced by a closed-loop chain, the configurable platform. The use of a closed-loop chain allows the robot to interact with the environment from multiple contact points on the platform, which reflects the presence of multiple end-effectors. This results in a robot that successfully combines motion and grasping capabilities into a structure that provides an inherent high stiffness. This paper aims to introduce the QuadroG robot, a 4 degrees of freedom PRCP which finely merges planar motion together with grasping capabilities.

scholarly journals Kinematics, Workspace, and Singularity Analysis of a Parallel Robot With Five Operation Modes

2018 ◽  
Vol 10 (3) ◽  
Author(s):  
Damien Chablat ◽  
Xianwen Kong ◽  
Chengwei Zhang
Keyword(s):  
Degrees Of Freedom ◽  
Rotation Axis ◽  
Operation Mode ◽  
Parallel Robot ◽  
Joint Space ◽  
Singularity Analysis ◽  
Parallel Robots ◽  
Operation Modes ◽  
Serial Chain ◽  
Kinematic Study

Most multimode parallel robots can change operation modes by passing through constraint singularities. This paper deals with a comprehensive kinematic study of a three degrees-of-freedom (DOF) multimode three-PRPiR parallel robot developed at Heriot-watt University. This robot is able to reach several operation modes without crossing any constraint singularity by using lockable Pi and R joints. Here, a Pi joint may act as a 1DOF planar parallelogram if its lockable P (prismatic) joint is locked or a 2DOF RR serial chain if its lockable P joint is released. The operation modes of the robot include a 3T operation mode and four 2T1R operation modes with two different directions of the rotation axis of the moving platform. The inverse kinematics and forward kinematics of the robot in each operation mode are dealt with in detail. The joint space and workspace analysis of the robot allow us to know the regions of the workspace that the robot can reach in each operation mode. It is shown that the robot is able to change assembly mode in one operation mode by passing through another operation mode.

scholarly journals Modeling and Control of a Cable-Suspended Sling-Like Parallel Robot for Throwing Operations

2020 ◽  
Vol 10 (24) ◽  
pp. 9067
Author(s):  
Deng Lin ◽  
Giovanni Mottola ◽  
Marco Carricato ◽  
Xiaoling Jiang
Keyword(s):  
Mathematical Models ◽  
Degrees Of Freedom ◽  
Parallel Robot ◽  
Parallel Robots ◽  
Target Point ◽  
Inertial Effects ◽  
End Effector ◽  
Modeling And Control ◽  
And Control ◽  
Three Degrees Of Freedom

Cable-driven parallel robots can provide interesting advantages over conventional robots with rigid links; in particular, robots with a cable-suspended architecture can have very large workspaces. Recent research has shown that dynamic trajectories allow the robot to further increase its workspace by taking advantage of inertial effects. In our work, we consider a three-degrees-of-freedom parallel robot suspended by three cables, with a point-mass end-effector. This model was considered in previous works to analyze the conditions for dynamical feasibility of a trajectory. Here, we enhance the robot’s capabilities by using it as a sling, that is, by throwing a mass at a suitable time. The mass is carried at the end-effector by a gripper, which releases the mass so that it can reach a given target point. Mathematical models are presented that provide guidelines for planning the trajectory. Moreover, results are shown from simulations that include the effect of cable elasticity. Finally, suggestions are offered regarding how such a trajectory can be optimized.

scholarly journals Rotational Workspace Expansion of a Planar CDPR with a Circular End-Effector Mechanism Allowing Passive Reconfiguration

Robotics ◽  
2019 ◽  
Vol 8 (3) ◽  
pp. 57 ◽  
Author(s):  
Marco Carpio Alemán ◽  
Roque Saltaren ◽  
Alejandro Rodriguez ◽  
Gerardo Portilla ◽  
Juan Placencia
Keyword(s):  
Degrees Of Freedom ◽  
Parallel Robot ◽  
Parallel Robots ◽  
End Effector ◽  
Effector Mechanism ◽  
Circular Structure ◽  
Adams Software ◽  
Anchor Points ◽  
Orientation Workspace ◽  
Three Degrees Of Freedom

Cable-Driven Parallel Robots (CDPR) operate over a large positional workspace and a relatively large orientation workspace. In the present work, the expansion of the orientation Wrench Feasible Workspace (WFW) in a planar four-cable passive reconfigurable parallel robot with three degrees of freedom was determined. To this end, we proposed a circular-geometry effector mechanism, whose structure allows automatic mobility of the two anchor points of the cables supporting the End Effector (EE). The WFW of the proposed circular structure robot was compared with that of a traditional robot with a rectangular geometry and fixed anchor points. Considering the feasible geometric and tension forces on the cables, the generated workspace volume of the robot was demonstrated in an analysis-by-intervals. The results were validated by simulating the orientation movements of the robot in ADAMS software and a real experimental test was developed for a hypothetical case. The proposed design significantly expanded the orientation workspace of the robot. The remaining limitation is the segment of the travel space in which the mobile connection points can slide. Overcoming this limitation would enable the maximum rotation of the EE.

Oscillation Reduction and Frequency Analysis of Under-Constrained Cable-Driven Parallel Robot with Three Cables

Robotica ◽  
2019 ◽  
Vol 38 (3) ◽  
pp. 375-395 ◽  
Author(s):  
Sung Wook Hwang ◽  
Jeong-Hyeon Bak ◽  
Jonghyun Yoon ◽  
Jong Hyeon Park
Keyword(s):  
Frequency Analysis ◽  
Degrees Of Freedom ◽  
Natural Frequencies ◽  
Vibration Suppression ◽  
Parallel Manipulators ◽  
Parallel Robot ◽  
Parallel Robots ◽  
Input Shaping ◽  
End Effector ◽  
Multi Mode

SummaryCable-driven parallel robots (CDPRs) possess a lot of advantages over conventional parallel manipulators and link-based robot manipulators in terms of acceleration due to their low inertia. This paper deals with under-constrained CDPRs, which manipulate the end-effector to carrying the payload by using a number of cables less than six, often used preferably owing to their simple structures. Since a smaller number of cables than six are used, the end-effector of CDPR has uncontrollable degrees of freedom and that causes swaying motion and oscillations. In this paper, a scheme to curb on the unwanted oscillation of the end-effector of the CDPR with three cables is proposed based on multimode input shaping. The precise dynamic model of the under-constrained CDPR is obtained to find natural frequencies, which depends on the position of the end-effector. The advantage of the proposed method is that it is practicable to generate the trajectories for vibration suppression based on multi-mode input-shaping scheme in spite of the complexity in the dynamics and the difficulty in computing the natural frequencies of the CDPR, which are required in any input-shaping scheme. To prove the effectiveness of the proposed method, computer simulations and experiments were carried out by using 3-D motion for CDPR with three cables.

Clearance-Induced Position Uncertainty of Planar Linkages and Parallel Manipulators

2017 ◽  
Vol 9 (6) ◽  
Author(s):  
Kwun-Lon Ting ◽  
Kuan-Lun Hsu ◽  
Jun Wang
Keyword(s):  
Degrees Of Freedom ◽  
Kinematic Model ◽  
Target Position ◽  
Parallel Manipulators ◽  
Parallel Robot ◽  
Parallel Robots ◽  
Joint Clearance ◽  
Position Uncertainty ◽  
Kinematic Effect ◽  
Joint Clearances

The paper presents a simple and effective kinematic model and methodology to assess and evaluate the extent of the position uncertainty caused by joint clearances for multiple-loop linkage and manipulators connected with revolute or prismatic pairs. The model is derived and explained with geometric rigor based on Ting's rotatability laws. The significant contributions include (1) the clearance link model for a P-joint that catches the translation and oscillation characteristics of the slider within the clearance and separates the geometric effect of clearances from the input error, (2) the generality of the method, which is effective for multiloop linkages and parallel manipulators, and (3) settling the dispute on the position uncertainty effect to parallel and serial robots due to joint clearance. The discussion is illustrated and carried out through symmetrically configured planar 8 bar parallel robots. It is found that at a target position, the uncertainty region of a three degrees-of-freedom (DOF) three-leg parallel robot is enclosed by a hexagon with curve edges, while that of its serial counterpart is enclosed by a circle included in the hexagon. A numerical example is presented. The finding and proof, though only based on three-leg planar 8 bar parallel robots, may have a wider implication suggesting that based on the kinematic effect of joint clearance, parallel robots tends to inherit more position uncertainty than their serial counterparts. The use of more loops in not only parallel robots but also single-DOF linkages cannot fully offset the adverse effect on position uncertainty caused by the use of more joints.

A learning-based control framework for cable-driven parallel robots with unknown Jacobians

2020 ◽  
Vol 234 (9) ◽  
pp. 1024-1036
Author(s):  
Hao Xiong ◽  
Lin Zhang ◽  
Xiumin Diao
Keyword(s):  
Neural Network ◽  
Control Strategy ◽  
Degrees Of Freedom ◽  
Inverse Dynamics ◽  
Parallel Robot ◽  
Joint Space ◽  
Parallel Robots ◽  
The Neural Network ◽  
Control Framework ◽  
In Series

Cable-driven parallel robots have been studied by many researchers in the past decades. The Jacobian of a cable-driven parallel robot may not be determined in some applications such as rehabilitation. In order to control the pose of a fully constrained cable-driven parallel robot with unknown Jacobian and driven by torque-controlled actuators, a learning-based control framework consisting of a robust controller and a neural network in series is proposed in this article. The neural network takes over the role of the Jacobian by mapping a wrench applied on the end-effector of the cable-driven parallel robot at a pose in the task space to a set of cable tensions in the joint space. In this way, the cable-driven parallel robot can be controlled by cable tensions derived from such a mapping, rather than solving the inverse dynamics problem based on the Jacobian. As an example, a control strategy is developed to demonstrate how the proposed control framework works. The control strategy includes a proportional–integral–derivative controller and a feedforward neural network. Simulation results show that the control strategy can successfully control a cable-driven parallel robot with four cables, three degrees of freedom, and unknown Jacobian.

Sign in / Sign up

Export Citation Format

Share Document