Numerical Simulation of Dynamic Bending Deflection of a Disc Cam Profile With Roller Follower System

2020 ◽  
Author(s):  
Louay S. Yousuf ◽  
Yaakob K. H. Dabool
Keyword(s):  
Numerical Simulation ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Dynamic Response ◽  
Contact Pressure ◽  
Infrared Camera ◽  
Radius Of Curvature ◽  
Element Analysis ◽  
Cam Profile ◽  
Maximum Contact

Abstract The bending deflection of the disc cam profile and the dynamic response of the follower were discussed and analyzed for three paths of contact. The objective of this paper was to study the influence of maximum contact pressure on the bending deflection of the cam profile. Numerical simulation was carried out using SolidWorks Software to simulate the follower displacement, velocity and acceleration. Finite element analysis was used taking into account the use of ANSYS package to calculate the bending deflection. The experiment setup had been done through an infrared camera device. The bending deflection of point (18) is bigger than the bending deflection of point (4) because of the bigness of radius of curvature of nose (2).

scholarly journals Deflection calculation of cam profile due to a Hertzian contact pressure

2020 ◽  
Vol 37 ◽  
pp. 149-160
Author(s):  
Louay S Yousuf
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Dynamic Response ◽  
Contact Pressure ◽  
Reduction Rate ◽  
Hertzian Contact ◽  
Element Analysis ◽  
Cam Profile ◽  
The Impact ◽  
Contact Parameters

Abstract The bending deflection of cam profile was analyzed for three paths of contact and distinct Hertzian contact pressure. The impact happened between the disc cam and roller follower based on the contact parameters. The contact parameters are contact body stiffness, sliding contact velocity, exponent and penetration. A disc cam and roller follower system were discussed and analyzed for the dynamic response of the follower and bending deflection of the cam profile. The objective of this paper was to study the effect of contact load on the bending deflection. A system with spring stiffness (k) and viscous damping coefficient (c) at the end of the follower stem was used to reduce the bending deflection on the cam profile. The theory of circular plate was applied to derive the analytic solution of the bending deflection. The dynamic response of the follower had been determined by using the SolidWorks software based on the contact parameters. The experimental setup was done through an infrared camera device. Finite-element analysis was used to calculate the bending deflection of the cam profile numerically. Finite-element analysis was carried out by using the ANSYS version 19.2 package. The analytic and simulation results are checked and verified for bending deflection at the point of contact. The reduction rate for bending deflection was 73.425% for path no. (1), 85.925% for path no. (2) and 61.467% for path no. (3).

Evaluation of the Elliptical Flange Configurations for 24-Inch and 30-Inch Heater/Cooler Units

2007 ◽  
Author(s):  
Chris Alexander ◽  
Wade Armer ◽  
Stuart Harbert
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Heat Exchanger ◽  
Contact Pressure ◽  
Parameter Study ◽  
Element Analysis ◽  
Iterative Design ◽  
Pressure Changes ◽  
Geometric Changes ◽  
Maximum Contact

KOCH Heat Transfer Company contracted Stress Engineering Services, Inc. to perform a design/parameter study of a return bonnet used in hairpin heat exchangers that employs an elliptical flange design. The return bonnet is an important component of the heat exchanger as it can be removed to permit inspection of the heat exchanger tubes. The return bonnet is bolted to the hairpin leg flange. To maintain sealing integrity a gasket is placed between the return bonnet flange and the hairpin leg flange. The sealing efficiency of two return bonnet sizes (24-inch and 30-inch) was investigated in this study using finite element analysis. The sealing efficiency is an indication of how the contact pressure changes circumferentially around the gasket and is calculated by dividing the local contact pressure by the maximum contact pressure calculated in the gasket for each respective design. The study assessed the effects of geometric changes to the mating flanges. Using an iterative design process using finite element analysis, the elliptical flanges were optimized to maximize sealing efficiency. Upon completion of the study, the manufacturer successfully employed the modifications as evidenced with multiple successful hydrotests.

Flexible Flowline Walking Tendency on Seabed With Longitudinal Undulations and Transverse Gradients

2018 ◽  
Author(s):  
Graeme Roberts ◽  
T. Sriskandarajah ◽  
Gianluca Colonnelli ◽  
Arnaud Roux ◽  
Alan Roy ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Temperature Gradients ◽  
Radius Of Curvature ◽  
Bend Radius ◽  
Lateral Buckling ◽  
Element Analysis ◽  
Slip Tendency ◽  
Start Ups ◽  
The Impact

A method of carrying out a combined axial walking and lateral buckling assessment for a flexible flowline has been developed using finite element analysis. The method overcomes limitations of screening assessments which could be inconclusive when applied either to a flexible flowline on an undulating seabed with transverse gradients or to one that buckles during hydrotest. Flexible flowlines that were to be surface-laid on a seabed with longitudinal undulations and transverse gradients were assessed using the method. The flexible flowlines were simulated in their as-laid state, and the simulation incorporated hydrotest pressure and the pressure & temperature gradients and transients associated with multiple start-ups. The objective was to quantify the axial walking and lateral slip tendency of the flexible flowlines and the impact that walking might have on the connected end structures. The lateral buckle locations predicted by finite element analysis were compared to a post-hydrotest survey and the radius of curvature from analysis was compared to the minimum bend radius of the flexible.

scholarly journals Effect of coronal plane acetabular correction on joint contact pressure in Periacetabular osteotomy: a finite-element analysis

2022 ◽  
Vol 23 (1) ◽  
Author(s):  
Kenji Kitamura ◽  
Masanori Fujii ◽  
Miho Iwamoto ◽  
Satoshi Ikemura ◽  
Satoshi Hamai ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Contact Pressure ◽  
Periacetabular Osteotomy ◽  
Anterior Wall ◽  
Coronal Plane ◽  
Patient Specific ◽  
Element Analysis ◽  
Joint Contact ◽  
Joint Contact Pressure

Abstract Background The ideal acetabular position for optimizing hip joint biomechanics in periacetabular osteotomy (PAO) remains unclear. We aimed to determine the relationship between acetabular correction in the coronal plane and joint contact pressure (CP) and identify morphological factors associated with residual abnormal CP after correction. Methods Using CT images from 44 patients with hip dysplasia, we performed three patterns of virtual PAOs on patient-specific 3D hip models; the acetabulum was rotated laterally to the lateral center-edge angles (LCEA) of 30°, 35°, and 40°. Finite-element analysis was used to calculate the CP of the acetabular cartilage during a single-leg stance. Results Coronal correction to the LCEA of 30° decreased the median maximum CP 0.5-fold compared to preoperatively (p <  0.001). Additional correction to the LCEA of 40° further decreased CP in 15 hips (34%) but conversely increased CP in 29 hips (66%). The increase in CP was associated with greater preoperative extrusion index (p = 0.030) and roundness index (p = 0.038). Overall, virtual PAO failed to normalize CP in 11 hips (25%), and a small anterior wall index (p = 0.049) and a large roundness index (p = 0.003) were associated with residual abnormal CP. Conclusions The degree of acetabular correction in the coronal plane where CP is minimized varied among patients. Coronal plane correction alone failed to normalize CP in 25% of patients in this study. In patients with an anterior acetabular deficiency (anterior wall index < 0.21) and an aspherical femoral head (roundness index > 53.2%), coronal plane correction alone may not normalize CP. Further studies are needed to clarify the effectiveness of multiplanar correction, including in the sagittal and axial planes, in optimizing the hip joint’s contact mechanics.

The Numerical Simulation and Finite-Element Analysis of the Motor Vibration Problem Based on the Base Anchor Softening Layer

2013 ◽  
Vol 815 ◽  
pp. 860-867
Author(s):  
Yu Gu ◽  
Shao Xiong Li ◽  
Rui Li ◽  
Qiang Li
Keyword(s):  
Numerical Simulation ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Exciting Force ◽  
Element Analysis ◽  
Comparison Results ◽  
Inherent Frequency ◽  
Motor Model ◽  
Motor Vibration ◽  
Important Significance

Vibration results from situation when the inherent frequency close to the external exciting force during the operation of the motor, so accurate and effective calculation of the natural frequency of the motor has an important significance to damping noise. By numerical simulation model and the ANSYS finite element modal, the inherent frequencies were got of the motor and comparison results verify the effectiveness of the motor model. The effect of the modulus of elasticity of the softening layer between the motor and the ground to the inherent frequency was researched intensively, and puts forward related suggestions.

Dynamic Finite Element Analysis of a Cylindrical Roller Bearing

2011 ◽  
Vol 143-144 ◽  
pp. 437-442
Author(s):  
Bao Hong Tong ◽  
Yin Liu ◽  
Xiao Qian Sun ◽  
Xin Ming Cheng
Keyword(s):  
Numerical Simulation ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Roller Bearing ◽  
Element Analysis ◽  
Dynamic Finite Element ◽  
Dynamic Finite Element Analysis ◽  
Simulation Results ◽  
Cylindrical Roller Bearing ◽  
Cylindrical Roller

A dynamic finite element analysis model for cylindrical roller bearing is developed, and the complex stress distribution and dynamic contacting nature of the bearing are investigated carefully based on ANSYS/LS-DYNA. Numerical simulation results show that the stress would be bigger when the element contacting with the inner or outer ring than at other times, and the biggest stress would appear near the area that roller contacting with the inner ring. Phenomenon of stress concentration on the roller is found to be very obvious during the operating process of the bearing system. The stress distributions of different elements are uneven on the same side surface of roller in its axis direction. Numerical simulation results can give useful references for the design and analysis of rolling bearing.

scholarly journals An Analysis Tool for the Installation of Submarine Cables in an S-Lay Configuration Including “In and Out of Water” Cable Segments

2020 ◽  
Vol 8 (1) ◽  
pp. 48 ◽  
Author(s):  
Vasileios A. Mamatsopoulos ◽  
Constantine Michailides ◽  
Efstathios E. Theotokoglou
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Design Criterion ◽  
Limiting Factors ◽  
Radius Of Curvature ◽  
Analysis Tool ◽  
Analysis Software ◽  
Element Analysis ◽  
Analysis And Design ◽  
Custom Made

Today, the offshore oil and gas and wind power industry is a heavily regulated segment, and current standards have established restrictions which yield a very limited weather window for submarine cable installations due to experience with cable failure in bad weather. There are two main limiting factors in current practice during cable installation of an S-lay configuration: the design criterion for the minimum allowable radius of curvature in the touch down point and the avoidance of axial compression in the touch down zone. Accurate assessment of the cable integrity during offshore installation has drawn great attention and is related to the existing available analysis and design tools. The main purpose of this paper is to develop and propose a quick and easy custom-made analysis tool, which is able to export similar results as sophisticated finite element analysis software. The developed tool utilizes analytical equations of a catenary-type submarine structure extended to account for varying cross-sections with different weights and/or stiffnesses, as is the real practice. A comparative study is presented in this paper to evaluate the significance for the modeling of the “out of water” cable segment required for accurate safety factor quantification during a laying operation. The efficiency and accuracy of the proposed tool are proven through a validation study comparing the results and the computational effort and time with commercial finite element analysis software. The analysis error in the case of not modeling the “out of water” cable part is significant, especially in shallow water areas, which proves the importance of using the proposed analysis tool.

Finite Element Analysis for Gear Contact Based on UG and ABAQUS

2013 ◽  
Vol 442 ◽  
pp. 229-232 ◽  
Author(s):  
Li Mei Wu ◽  
Fei Yang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Contact Stress ◽  
Three Dimensional ◽  
Element Model ◽  
Tooth Surface ◽  
Element Analysis ◽  
Tooth Width ◽  
Gear Contact ◽  
Maximum Contact

According to the cutting theory of involute tooth profile, established an exact three-dimensional parametric model by UG. Used ABAQUS to crate finite element model for gear meshing. After simulated the meshing process, discussed the periodicity of the tooth surface contact stress. Based on the result of finite element analysis, made a comparison of the maximum contact stress between finite element solution and Hertz theoretical solution, analyzed the contact stress distribution on tooth width, and researched the effect of friction factor on contact stress. All that provided some theoretical basis for gear contact strength design.

Sign in / Sign up

Export Citation Format

Share Document