Effect of Biodiesel-Ethanol Blended Fuel Spray Characteristics on the Reduction of Exhaust Emissions in a Common-Rail Diesel Engine

2008 ◽  
Author(s):  
Seung Hyun Yoon ◽  
Su Han Park ◽  
Hyun Kyu Suh ◽  
Chang Sik Lee
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Injection Rate ◽  
Fuel Spray ◽  
Exhaust Emission ◽  
Emission Characteristics ◽  
Blended Fuel ◽  
Ethanol Blends ◽  
Blended Fuels ◽  
Conventional Diesel Fuel

An experiment was performed to analyze the effects of biodiesel-ethanol blended fuel spray on the combustion and exhaust emission characteristics of a single-cylinder common-rail diesel engine. To analyze the macroscopic and microscopic characteristics of biodiesel blended fuel spray, measurements of the injection rate, droplet diameter, and spray tip penetration were taken using an injection rate meter, spray visualization and a droplet measuring system. The combustion, exhaust emission characteristics and size distributions of particulate matter were determined for various engine operating conditions using biodiesel-ethanol blends, and the results were compared to those of conventional diesel fuel. In this investigation, the measured results of biodiesel-ethanol blended fuels show that the Sauter mean diameter (SMD) decreased with an increase of relative velocity between the injected fuel and ambient gas. Comparing the combustion characteristics of diesel fuel and biodiesel-ethanol blended fuels, both diesel and blended fuel showed similar trends in combustion pressure and the rate of heat release. However, the combustion of biodiesel-ethanol blends had lower combustion characteristics such as combustion pressures and heat release rates than those of diesel fuel because of their lower heating values. In the case of exhaust gas recirculation (EGR), the indicated specific NOx (ISNOx), and soot concentrations were lower than those of conventional diesel fuel.

Effect of Biodiesel-Ethanol Blended Fuel Spray Characteristics on the Reduction of Exhaust Emissions in a Common-Rail Diesel Engine

2010 ◽  
Vol 132 (4) ◽  
Author(s):  
Seung Hyun Yoon ◽  
Su Han Park ◽  
Hyun Kyu Suh ◽  
Chang Sik Lee
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Diesel Fuel ◽  
Injection Rate ◽  
Combustion Characteristics ◽  
Common Rail ◽  
Fuel Spray ◽  
Blended Fuel ◽  
Ethanol Blends ◽  
Conventional Diesel Fuel

An experimental investigation was performed to analyze the effects of biodiesel-ethanol blended fuel spray on the combustion, and exhaust emission characteristics in a single cylinder common-rail diesel engine. In order to analyze the macroscopic and microscopic characteristics of biodiesel blended fuel spray, parameters, such as injection rate, droplet diameter, and spray tip penetration, were measured using an injection rate meter system, spray visualization, and droplet measuring system. Also, measurements of combustion, exhaust emissions, and size distributions of particulate matter were carried out under various engine operating conditions for biodiesel-ethanol blends and the results were compared with those of conventional diesel fuel. In this investigation, the measured results of biodiesel-ethanol blended fuel show that the Sauter mean diameter decreased with the increase of relative velocity between the injected fuel and the ambient gas. Comparing the combustion characteristics of diesel fuel and biodiesel-ethanol blended fuels, both diesel and blended fuel show similar trends of combustion pressure and rate of heat release. However, the combustion of biodiesel-ethanol blends indicated lower combustion characteristics, such as combustion pressures and heat release rates, than those of diesel fuel because of its lower heating value. In the case of exhaust gas recirculation, the indicated specific NOx(ISNOx) and soot concentration results showed lower emissions compared with those of conventional diesel fuel.

Spray and Combustion Characteristics of Biodiesel∕Diesel Blended Fuel in a Direct Injection Common-Rail Diesel Engine

2008 ◽  
Vol 130 (3) ◽  
Author(s):  
Hyun Kyu Suh ◽  
Hyun Gu Roh ◽  
Chang Sik Lee
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Direct Injection ◽  
Injection Rate ◽  
Combustion Characteristics ◽  
Biodiesel Fuel ◽  
Injection Timing ◽  
Pilot Injection ◽  
Blended Fuel ◽  
Conventional Diesel Fuel

The aim of this work is to investigate the effect of the blending ratio and pilot injection on the spray and combustion characteristics of biodiesel fuel and compare these factors with those of diesel fuel in a direct injection common-rail diesel engine. In order to study the factors influencing the spray and combustion characteristics of biodiesel fuel, experiments involving exhaust emissions and engine performance were conducted at various biodiesel blending ratios and injection conditions for engine operating conditions. The macroscopic and microscopic spray characteristics of biodiesel fuel, such as injection rate, split injection effect, spray tip penetration, droplet diameter, and axial velocity distribution, were compared with the results from conventional diesel fuel. For biodiesel blended fuel, it was revealed that a higher injection pressure is needed to achieve the same injection rate at a higher blending ratio. The spray tip penetration of biodiesel fuel was similar to that of diesel. The atomization characteristics of biodiesel show that it has higher Sauter mean diameter and lower spray velocity than conventional diesel fuel due to high viscosity and surface tension. The peak combustion pressures of diesel and blending fuel increased with advanced injection timing and the combustion pressure of biodiesel fuel is higher than that of diesel fuel. As the pilot injection timing is retarded to 15deg of BTDC that is closed by the top dead center, the dissimilarities of diesel and blending fuels combustion pressure are reduced. It was found that the pilot injection enhanced the deteriorated spray and combustion characteristics of biodiesel fuel caused by different physical properties of the fuel.

scholarly journals Effect of Adding RON97 Into Waste Cooking Oil as an Alternative Fuel for Diesel Engine

2018 ◽  
Vol 7 (3.11) ◽  
pp. 113
Author(s):  
Idris Saad ◽  
Wardatul Hayah Ab Rashid ◽  
Nur Hidayah Saidon
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Calorific Value ◽  
Alternative Fuel ◽  
Waste Cooking Oil ◽  
Fuel Blend ◽  
Cooking Oil ◽  
Blended Fuel ◽  
Blended Fuels ◽  
Conventional Diesel Fuel

Petroleum-based fuel reserves are drastically depleting due to a high demand on sustaining a better lifestyle. This paper presents the utilization of waste cooking oil (WCO) as an alternative fuel for diesel engine. Although WCO and conventional diesel fuel have similar physiochemical properties, the properties of WCO is considered inferior than conventional diesel fuel. It is due to higher viscosity and density of WCO while its calorific value is lower than conventional diesel fuel. In this research, unmodified WCO was blended with petrol fuel grade RON97.  Five blended fuels samples were prepared from five to 25 percent volume base with five percent step increment. The density and calorific value of all fuel blend samples together with unmodified WCO were measured and compared to the conventional diesel and RON97 fuels. Each of the blended fuel and conventional diesel were used to run a single cylinder diesel engine. The performance characteristic of the engine was recorded at different engine speeds ranging between 1500 and 3000 rpm. Results showed that the properties of blended fuel were inferior compared to the conventional diesel fuel; however, by adding 15 percent of RON97 into the unmodified WCO, the results were comparable to the conventional diesel fuel.  

Study of Lubricant Viscosity From Diesel Engine Operating on Various Percentages of Coconut Oil Blended Fuel

2005 ◽  
Author(s):  
M. Varman ◽  
M. S. Faizul ◽  
H. H. Masjuki ◽  
M. A. Kalam ◽  
T. M. I. Mahlia
Keyword(s):  
Diesel Engine ◽  
Life Span ◽  
Diesel Fuel ◽  
Coconut Oil ◽  
Fuel System ◽  
Lower Viscosity ◽  
Blended Fuel ◽  
Blended Fuels ◽  
Conventional Diesel Fuel ◽  
Lubricant Viscosity

In this study, the lubricant viscosity from a diesel engine operating on various percentages of coconut oil blended fuel is investigated to determine the suitable mixture appropriate for a diesel engine. The coconut oil was blended with conventional diesel fuel at an amount varying from ten to fifty percent. The lubricant used in this study is the conventional commercially available lubricant (SAE 40). After proper blending of diesel with coconut oil, the blended fuels are loaded into the fuel tank. The engine is operated at half throttle setting running at 1600 rpm for 100 hours. At every ten hour interval, one lubricant sample was collected and analyzed using a viscometer at 100 °C and 40 °C. The results show that the viscosity for all the blended fuel remain about constant throughout the 100 hours test. However, fifty percent coconut oil blended fuel at 40 °C shows slightly lower viscosity level in comparison to other percentages of blended fuel system. It is expected this is due to high fuel dilution in lube oil. As a result, ten to thirty percent coconut oil blended fuels seems suitable for diesel engine because it’s able to prolong lubricant life span by maintaining its viscosity.

Diesel Fuel Multiple Injection Effects on Emission Characteristics of Diesel Engine Mixed Ammonia Gas Into Intake Air

2019 ◽  
Vol 141 (6) ◽  
Author(s):  
Yoichi Niki ◽  
Yoshifuru Nitta ◽  
Hidenori Sekiguchi ◽  
Koichi Hirata
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Internal Combustion Engines ◽  
Experimental Results ◽  
Exhaust Emission ◽  
N2o Emissions ◽  
Emission Characteristics ◽  
Exhaust Gas ◽  
N2o Production ◽  
Combustion Processes

This study focuses NH3 as an alternative fuel for internal combustion engines, because NH3 is known as a H2 carrier and its combustion does not produce CO2 causing global warming. On the other hand, some reports show that unburned NH3 and N2O appear in exhaust gas, when NH3 is used as fuel for compression ignition or spark ignition engines. NH3 is toxic and N2O is one of the greenhouse gases. These emissions should not be emitted. These reports point out that exhaust gas after treatments and/or injection strategies can be effective to reduce these emissions. From our previous investigations, it was confirmed that NH3 and N2O were contained in the exhaust gas of a conventional diesel engine with NH3 gas mixed into the engine intake. In this study, NH3 combustion processes in the diesel engine were investigated from the experimental results. Based on the investigations, a pilot or postinjection was conducted to reduce emissions of NH3 and N2O. In this paper, first the experimental results of the combustion and exhaust emission characteristics on the conventional diesel engine with NH3 gas mixed into the engine intake are shown. NH3 and N2O emissions are then verified by analyzing the exhaust gas. Next, NH3 combustion processes in the diesel engine are considered from the experimental results to report on the effects of a pilot and postdiesel fuel injection on NH3 and N2O production processes. The experimental results suggest that the multiple diesel fuel injections would be one of the effective measures to reduce N2O and NH3 emissions on NH3 and diesel dual-fueled engine.

APPLICATION ON OXYGENATED FUEL OF MONO-ETHER GROUP IN AN IDI DIESEL ENGINE

2012 ◽  
Vol 06 ◽  
pp. 425-430
Author(s):  
HYUNG-GON KIM ◽  
SEUNG-HUN CHOI ◽  
YOUNG-TAIG OH
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Engine Performance ◽  
Exhaust Emission ◽  
Emission Characteristics ◽  
Butyl Ether ◽  
Ether Group ◽  
Oxygenated Fuel ◽  
Effect Of Oxygen ◽  
Gas Recirculation

Effect of oxygen components of fuels on exhaust emissions has been investigated by applying an indirect injection (IDI) diesel engine. This research analyzed variation and/or difference of the engine performance and exhaust emission characteristics of the IDI diesel engine by fueling the commercial diesel fuel and four different mixed ratios of oxygenated blended fuels. Effect of the exhaust gas recirculation (EGR) method was analyzed on the NOx emission characteristics. Ethylene glycol mono-n-butyl ether (EGBE) contains 27% of oxygen components in itself, and it is a kind of effective oxygenated fuel of mono-ether group. Smoke emission from the EGBE was reduced remarkably relative to the commercial diesel fuel. The EGBE can supply oxygen components sufficiently at higher diesel engine loads and speeds. It was found that a simultaneous reduction of the smoke and the NOx was achieved with the oxygenated fuel (10 vol-%) and the cooled EGR method (10%).

Exhaust Emission Characteristics of a Three-Wheeler Auto Diesel Engine Fueled with Pongamia, Mahua and Jatropha Biodiesels

2019 ◽  
Vol 13 ◽  
Author(s):  
Bobbili Prasadarao ◽  
Aditya Kolakoti ◽  
Pudi Sekhar
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Diesel Fuel ◽  
Edible Oils ◽  
Cetane Number ◽  
Alternative Fuel ◽  
Exhaust Emissions ◽  
International Standards ◽  
Exhaust Emission ◽  
Emission Characteristics

: This paper presents the production of biodiesel from three different non edible oils of Pongamia, Mahua and Jatropha as an alternative fuel for diesel engine. Biodiesel is produced by followed transesterification process, using catalyst sodium hydroxide (NaOH) and methyl alcohol (CH3OH). A single cylinder four stroke three-wheeler auto diesel engine is used to evaluate the exhaust emission characteristics at a constant speed of 1500rpm with varying loads. Diesel as a reference fuel and cent percent of Pongamia Methyl Ester (PME), Mahua Methyl Ester (MME) and Jatropha Methyl Ester (JME) are used as an alternative fuel. The physicochemical properties of biodiesels are within the limits of international standards (ASTM D6751) noticeably. The results of tested biodiesels offer low exhaust emissions compared to diesel fuel, owing to presence of molecular oxygen and high cetane number. At maximum load the NOx emission reduced by 18.41% for JME, 17.46% for MME and 7.61% for PME. Low levels of CO emissions are recorded for JME (66%) followed by MME (33%) and PME (22%). Unburnt hydrocarbon emissions were reduced by 85.75% for JME and MME, for PME 14.28% reduction is observed. Exhaust smoke emissions are also reduced for PME and MME by 18.84%, for JME 14.49%. As a conclusion, it is observed that all the methyl esters exhibit significant reduction in harmful exhaust emissions compared to diesel fuel and JME is noted as a better choice.

Sign in / Sign up

Export Citation Format

Share Document