Numerical Analysis of a Solar Organic Rankine Cycle (ORC) Unit With R245fa as Working Fluid

2012 ◽  
Author(s):  
Musbaudeen O. Bamgbopa ◽  
Eray Uzgoren
Keyword(s):  
Mass Flow ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Hot Water ◽  
Critical Parameters ◽  
Working Fluid ◽  
Flow Rates ◽  
Steady State Operation ◽  
Mass Flow Rates ◽  
Solar Field

This paper presents a solar Organic Rankine Cycle (ORC) for electricity generation; where a regression based approach is used for the working fluid. Models of the unit’s sub-components (pump, evaporator, expander and condenser) are also presented. Heat supplied by the solar field can heat the water up to 80–95 °C at mass flow rates of 2–12 kg/s and deliver energy to the ORC’s heat exchanger unit. Simulation results of steady state operation using the developed model shows a maximum power output of around 40 kWe. Both refrigerant and hot water mass flow rates in the system are identified as critical parameters to optimize the power production and the cycle efficiency.

Experimental Study on the Organic Rankine Cycle Power System Adopting Dual Expanders in Parallel

2014 ◽  
Author(s):  
Eunkoo Yoon ◽  
Hyun Jun Park ◽  
Hyun Dong Kim ◽  
Kyung Chun Kim ◽  
Sang Youl Yoon
Keyword(s):  
Heat Source ◽  
Power System ◽  
Water Temperature ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Hot Water ◽  
Working Fluid ◽  
Electric Heater ◽  
Shaft Power ◽  
Scroll Expanders

This study aims to evaluate the performance of an organic Rankine cycle (ORC) power system adopting dual expanders in parallel by experiment. A dual-expander ORC system was designed to provide competitive advantages over a general single expander ORC system in typical applications with large thermal fluctuation of heat sources such as solar heat, marine waste heat, and etc. The ORC system consists of two scroll expanders installed in parallel, a hydraulic diaphragm type pump to feed and pressurize the working fluid, R-245fa, two plate heat exchangers for the evaporator and the condenser, and two generators with shaft power torque meters. The two scroll expanders were modified from two oil-free air scroll compressors, and were tested in the ORC loop with R245fa. The maximum isentropic efficiency of each expander was measured about 53%, and the shaft power was reached to about 2kW. The hot water was used as heat source, and the water temperature was controlled up to 150 °C by the 100 kW-class electric heater. A circulating air-cooled chiller was utilized for the control of the cooling water temperature. In order to determine the static performance of the system, efficiencies and shaft powers were measured with 130 °C heat source temperature. In addition, performance tests were conducted with various working fluid mass flow rates to control pressure ratios. The characteristics and total thermal efficiency of the dual parallel expander ORC system and optimal operating modes are addressed.

Simulations of Waste Heat Recovery System Using R123 and R245fa for Heavy-Duty Diesel Engines

2013 ◽  
Vol 805-806 ◽  
pp. 1827-1835 ◽  
Author(s):  
Ming Shan Wei ◽  
Lei Shi ◽  
Chao Chen Ma ◽  
Danish Syed Noman
Keyword(s):  
Mass Flow ◽  
Thermal Efficiency ◽  
Waste Heat ◽  
Rankine Cycle ◽  
Heavy Duty ◽  
Engine Exhaust ◽  
Flow Rates ◽  
Working Fluids ◽  
Mass Flow Rates ◽  
Heavy Duty Diesel

To improve fuel economy, an Organic Rankine Cycle (ORC) system is proposed to recover waste heat from heavy-duty diesel engines. R123 and R245fa were selected as working fluids. Extensive numerical simulations were conducted to find thermal efficiency of the system under different evaporation pressures, mass flow rates of working fluids and temperature of engine exhaust gases. Results show that the system thermal efficiency was increased with the increase in evaporation pressure for both R123 and R245fa. Efficiency of R123 system was found to be greater than that of R245fa system. For Rankine cycle with both R123 and R245fa, mass flow rate range varied with the evaporation pressure. Limited by evaporation rates and thermal decomposition of the working fluid, the range of mass flow rates in R245fa system was narrower than the R123 system. The thermal efficiency with different temperatures of engine exhaust gases was similar under the fixed evaporation pressure.

Effect of nozzle angle, turbine inlets and mass flow rate on the performance of a bladeless turbine

2019 ◽  
Vol 234 (8) ◽  
pp. 1101-1107
Author(s):  
Muhammad Ali Kamran ◽  
Shahryar Manzoor
Keyword(s):  
Experimental Study ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Working Fluid ◽  
Operating Parameters ◽  
Lower Mass ◽  
Flow Rates ◽  
Significant Parameter ◽  
Mass Flow Rates

A comprehensive experimental study on the effects of different operating parameters on the efficiency of tesla turbine is reported. A bladeless turbine with nine discs and up to four turbine inlets was used, with water as the working fluid. The parameters investigated are the nozzle angle, number of turbine inlets and mass flow rates. Contrary to earlier studies, an effort was made to determine the performance under varying loading conditions, and hence identify the complete performance characteristics. The study revealed that efficiency of the turbine increases at lower nozzle angles and higher number of turbine inlets. It was observed that the nozzle angle becomes a significant parameter when the number of turbine inlets is increased. Efficiencies up to 78% were achieved when the working fluid entered the turbine through two nozzles at an angle of 7°. It was also noted that the turbine is most efficient at the designed mass flow rate, and the efficiency reduces appreciably if lower mass flow rates are fed to the turbine. The results obtained are an important contribution to the available knowledge and can be used as design references for further studies.

scholarly journals Assessment of a District Trigeneration Biomass Powered Double Organic Rankine Cycle as Primed Mover and Supported Cooling

Energies ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 1030
Author(s):  
Muhammad Tauseef Nasir ◽  
Michael Chukwuemeka Ekwonu ◽  
Yoonseong Park ◽  
Javad Abolfazli Esfahani ◽  
Kyung Chun Kim
Keyword(s):  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Hot Water ◽  
Design Parameters ◽  
Working Fluid ◽  
Small Scale ◽  
Vapor Compression ◽  
Medium Temperature ◽  
Exergetic Analysis ◽  
The Impact

This study presents a combined cooling, heating, and power system powered by biogas, suitable for small scale communities in remote locations. To run such a system, in order to obtain the daily life essentials of electricity, hot water, and cooling, municipal waste can be considered as an option. Furthermore, the organic Rankine cycle part of the organic Rankine cycle powered vapor compression chiller can be used in times of need for additional electric production. The system comprises a medium temperature organic Rankine cycle utilizing M-xylene as its working fluid, and the cooling was covered by an Isobutane vapor compression cycle powered by an R245fa employing organic Rankine cycle. The system analyzed was designated to provide 250 kW of electricity. The energetic and exergetic analysis was performed, considering several system design parameters. The impact of the design parameters in the prime mover has a much greater effect on the whole system. The system proposed can deliver cooling values at the rate between 9.19 and 22 kW and heating values ranging from 879 up to 1255 kW, depending on the design parameter. Furthermore, the second law efficiency of the system was found to be approximately 56% at the baseline conditions and can be increased to 64.5%.

scholarly journals Inert Gas and Refrigerating Vapor Mass Flow Rates Ratio: A Much Promising Parameter for Diffusion-Absorption-Refrigeration Systems Performances Evaluation

2021 ◽  
Vol 8 (2) ◽  
pp. 253-258
Author(s):  
Djallel Zebbar ◽  
Souhila Zebbar ◽  
Sahraoui Kherris ◽  
Kouider Mostefa
Keyword(s):  
Mass Flow ◽  
Gas Flow ◽  
Inert Gas ◽  
Coefficient Of Performance ◽  
Working Fluid ◽  
Absorption Refrigeration ◽  
Flow Rates ◽  
Mass Flow Rates ◽  
Diffusion Absorption ◽  
Vapor Mass

This paper is consecrated to the thermodynamic study and analysis of diffusion-absorption-refrigeration (DAR) plants. The mass and energy balances analysis at the evaporator has allowed to highlight a new and original parameter, which can be used to analyze DAR system performances. It is the ratio of inert gas to refrigerant vapor mass flow rates at the evaporator inlets. This coefficient, which expression has been for the first time deduced mathematically, informs about the quality of the cycle and its performance, which are deeply affected by the growth of the inert gas flow energy expended to drive the refrigerant through the evaporator. The study shows that the coefficient of performance is decreasing with the increase of the mass flow rates ratio. The latter can be also used to find the optimal operating mode for the DAR machine with a specified working fluid.

scholarly journals Evaluation of the Energy Performance of an Organic Rankine Cycle-Based Micro Combined Heat and Power System Involving a Hermetic Scroll Expander

2013 ◽  
Vol 135 (4) ◽  
Author(s):  
Jean-François Oudkerk ◽  
Sylvain Quoilin ◽  
Sébastien Declaye ◽  
Ludovic Guillaume ◽  
Eric Winandy ◽  
...  
Keyword(s):  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Combined Heat And Power ◽  
Hot Water ◽  
Working Fluid ◽  
Inlet Temperature ◽  
Electrical Efficiency ◽  
Scroll Expander ◽  
Significant Difference ◽  
Temperature Application

This paper evaluates the performance of an organic Rankine cycle (ORC) based micro- combined heat and power (CHP) unit using a scroll expander. The considered system consists of a fuel boiler coupled with an ORC engine. As a preliminary step, the results of an experimental campaign and the modeling of a hermetic, lubricated scroll compressor used as an expander are presented. Then, a fluid comparison based on several criteria is conducted, leading to the selection of R245fa as working fluid for the ORC. A simulation model is then built to evaluate the performance of the system. The model associates an ORC model and a boiler model, both experimentally validated. This model is used to optimize and size the system. The optimization is performed considering two degrees of freedom: the evaporating temperature and the heat transfer fluid (HTF) mass flow rate. Seasonal simulation is finally performed with a bin method according to the standard PrEN14825 for an average European climate and for four heat emitter heating curves. Simulation results show that the electrical efficiency of the system varies from 6.35% for hot water at 65 °C (high temperature application) to 8.6% for a hot water temperature of 22 °C (low temperature application). Over one entire year, the system exhibits an overall electrical efficiency of about 8% and an overall thermal efficiency around 87% without significant difference between the four heat emitter heating curves. Finally, some improvements of the scroll expander are evaluated. It is shown that by increasing the maximum inlet temperature (limited to 140 °C due to technical reasons) and using two scroll expanders in series, the overall electrical efficiency reaches 12.5%.

Approach to Designing a Solar Concentrator for Small Scale Remote Power Application

2010 ◽  
Author(s):  
Khaled Metwally ◽  
Lamyaa A. El-Gabry ◽  
Ahmed Makhlouf
Keyword(s):  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Hot Water ◽  
Heat Transfer Fluid ◽  
Working Fluid ◽  
Small Scale ◽  
Concentrated Solar Power ◽  
Parabolic Trough ◽  
Capstone Project ◽  
Power Application

A small-scale concentrated solar power unit was designed to provide electricity and hot water using an organic Rankine cycle for Egypt as part of an undergraduate capstone project. The system was designed for a target power output of 3 KW. It uses parabolic troughs to heat ethylene glycol used as the heat transfer fluid which absorbs heat in the trough collector and transfers it to the working fluid through a heat exchanger. The system consists of 9 parabolic troughs and a total aperture area of 67 square meters, providing the required 3 KW of energy to the ORC. One parabolic trough was manufactured to test its thermal efficiency according to ASHRAE standard 93-2003 and compare it to its calculated value. A simple microcontroller-based system was used to track the sun.

scholarly journals Design and Analysis of the Domestic Micro-Cogeneration Potential for an ORC System Adapted to a Solar Domestic Hot Water System

Entropy ◽  
2019 ◽  
Vol 21 (9) ◽  
pp. 911 ◽  
Author(s):  
Daniel Leal-Chavez ◽  
Ricardo Beltran-Chacon ◽  
Paola Cardenas-Terrazas ◽  
Saúl Islas ◽  
Nicolás Velázquez
Keyword(s):  
Solar Collector ◽  
Electric Energy ◽  
Water System ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Point Of View ◽  
Hot Water ◽  
Working Fluid ◽  
Condensation Temperature ◽  
Domestic Hot Water

This paper proposes the configuration of an Organic Rankine Cycle (ORC) coupled to a solar domestic hot water system (SDHWS) with the purpose of analyzing the cogeneration capacity of the system. A simulation of the SDHWS was conducted at different temperatures, observing its performance to determine the amounts of useable heat generated by the solar collector; thus, from an energy balance point of view, the amount of heat that may be used by the ORC could be determined. The working fluid that would be suitable for the temperatures and pressures in the system was selected. The best fluid for the given conditions of superheated vapor at 120 °C and 604 kPa and a condensation temperature of 60 °C and 115 kPa was acetone. The main parameters for the expander thermodynamic design that may be used by the ORC were obtained, with the possibility of generating 443 kWh of annual electric energy with 6.65% global efficiency of solar to electric power, or an overall efficiency of the cogeneration system of 56.35% with a solar collector of 2.84 m2.

scholarly journals Simulation of the Part Load Behavior of Combined Heat Pump-Organic Rankine Cycle Systems

Energies ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3870
Author(s):  
Bernd Eppinger ◽  
Mustafa Muradi ◽  
Daniel Scharrer ◽  
Lars Zigan ◽  
Peter Bazan ◽  
...  
Keyword(s):  
Heat Pump ◽  
Mass Flow ◽  
Thermal Energy ◽  
Renewable Energy Sources ◽  
Organic Rankine Cycle ◽  
Rankine Cycle ◽  
Thermal Storage ◽  
Working Fluid ◽  
Part Load ◽  
Load Behavior

Pumped Thermal Energy Storages (PTES) are suitable for bridging temporary energy shortages, which may occur due to the utilization of renewable energy sources. A combined heat pump (HP)-Organic Rankine Cycle (ORC) system with suitable thermal storage offers a favorable way to store energy for small to medium sized applications. To address the aspect of flexibility, the part load behavior of a combined HP-ORC system, both having R1233zd(E) (Trans-1-chloro-3,3,3-trifluoropropene) as working fluid and being connected through a water filled sensible thermal energy storage, is investigated using a MATLAB code with integration of the fluid database REFPROP. The influence on the isentropic efficiency of the working machines and therefore the power to power efficiency (P2P) of the complete system is shown by variation of the mass flow and a temperature drop in the thermal storage. Further machine-specific parameters such as volumetric efficiency and internal leakage efficiency are also considered. The results show the performance characteristics of the PTES as a function of the load. While the drop in storage temperature has only slight effects on the P2P efficiency, the reduction in mass flow contributes to the biggest decrease in the efficiency. Furthermore, a simulation for dynamic load analysis of a small energy grid in a settlement is conducted to show the course of energy demand, supplied energy by photovoltaic (PV) systems, as well as the PTES performance indicators throughout an entire year. It is shown that the use of PTES is particularly useful in the period between winter and summer time, when demand and supplied photovoltaic energy are approximately equal.

Sign in / Sign up

Export Citation Format

Share Document