Dispersion of Particles Coming Out of the Mouth While Speaking in a Ventilated Indoor Environment

2021 ◽  
Author(s):  
Morteza Ali Masoomi ◽  
Mazyar Salmanzadeh ◽  
Goodarz Ahmadi
Keyword(s):  
Coming Out ◽  
Indoor Environment ◽  
Distribution Systems ◽  
Ventilation System ◽  
Field Studies ◽  
Continuous Phase ◽  
Ansys Fluent ◽  
Air Mixing ◽  
Long Time ◽  
Discrete Phase

Abstract Breathing air that contains virus-infected droplets is the leading cause of Covid-19 transmission. Sneezing, coughing, breathing, and talking of an infected person would generate aerosolized droplets that carry the coronavirus. Earlier research efforts have focused on sneezing and coughing as the primary transmission sources. New experiments and field studies have shown that breathing and talking are also effective mechanisms in spreading viruses. In this article, the dispersion of particles/droplets during speaking is studied. COVID-19 virus is about 120 nanometers and is suspended in saliva or mucus droplets emitted by an injected person. These droplets evaporate in a fraction of a second as they enter the environment and reduce in size. However, the droplets’ viral content remains the same as they move by the room’s airflow. The particles from sneezing and coughing are larger than those released by speaking. As the particles/droplets are small, the effect of gravity is small, and they remain suspended in the air for a long time. Also, being small makes them more easily penetrate the respiratory passages. Using the computational fluid dynamics method in conjunction with the ANSYS-Fluent software, the particle transport and dispersion were simulated. The Eulerian approach modeled the airflow (continuous phase), and the Lagrangian approach modeled the particle (discrete phase) movements. This study also investigated the ventilation system’s effects on the distribution of particles in the indoor environment. The displacement and mixing air distribution systems were considered. Simulation results showed that droplets remain suspended in the room for a relatively long time after evaporation. Large particles were deposited quickly, and a significant percentage of smaller particles were removed by the ventilation system. The concentration of particles in the upper half of the room was also quite low for the mixing ventilation system. This was due to the fact that the room air mixing system is relatively uniform; this uniformity of airflow caused the particles to get trapped quickly. Also, for the displacement system, the room airflow was not uniform; these particles were then dispersed in the room and spent more time in the indoor environment.

scholarly journals ENHANCEMENT OF MICROCLIMATE SUPPORT SYSTEMS IN POTATO STORE BUILDINGS

2020 ◽  
Vol 11 (3) ◽  
pp. 54-63
Author(s):  
M. P Kalashnikov
Keyword(s):  
Energy Efficient ◽  
Distribution Systems ◽  
Fruits And Vegetables ◽  
Ventilation System ◽  
Electric Energy ◽  
Field Studies ◽  
Storage Conditions ◽  
Air Distribution ◽  
Gas Composition

When storing fruits and vegetables, vital processes (respiration, heat and carbon dioxide) are actively proceeding. These processes lead to loss of production, significantly affect the temperature, humidity and gas composition of the air in the storage. The optimal storage conditions for fruits and vegetables are rather low positive temperatures and rather high humidity with a sufficient oxygen content in the air. Achieving this difficult task is most effectively accomplished by using active ventilation systems in the storage. The article provides a comparative assessment of setting up air exchange by energy-efficient microclimate systems in potato storages. The results of field studies of air conditions during operation of active air distribution systems in a potato storage are presented. Studies have shown that intensive flow ventilation of products close to the supply duct leads to an increase in losses (shrinkage) of vegetables up to 15 %. Since a number of containers with products are adjacent to large supply air holes thus subjected to the most severe blowing, the quality of potatoes is bound to deteriorate. The use in the active ventilation system of a highly efficient regenerative rotary heat exchanger ( E ≥ 85-90 %) and electronically-switched EC fans allows saving heat and electric energy, as well as reducing the mass loss of products by 21-26 % with directional supply of treated air to the inter-container space and containers with products.

scholarly journals CFD-based numerical simulation of cyclone separator for separating stigmas from petals of saffron

2020 ◽  
Author(s):  
Javad Nemati ◽  
Babak Beheshti ◽  
Ali Mohammad Borghei
Keyword(s):  
Separation Efficiency ◽  
Solid Phase ◽  
Equations Of Motion ◽  
Fluid Phase ◽  
Reynolds Stress Model ◽  
Continuous Phase ◽  
Solid Particles ◽  
Inlet Section ◽  
Ansys Fluent ◽  
Discrete Phase

This study numerically modeled the flow of a fluid (air) and solid particles (saffron flower) inside a cyclone using the finite volume method (FVM) in ANSYS Fluent. The continuous phase was simulated under steady state conditions, as the initial condition, using the Reynolds Stress Model (RSM) for turbulence at three constant inlet air velocities of 1.5 m/s, 2.5 m/s, and 3.5 m/s over the inlet section. One-way coupling was assumed to govern all numerical analyses. The fluid phase and particles were treated as the continuous medium (within a Eulerian framework) and discrete phase (within a Lagrangian framework), respectively. The equations governing the gas phase included the compressible Navier–Stokes and the conservation of mass. The discrete phase equations included the equations of motion for three different particles including petals, stigmas, and anthers. According to the numerical results, the cyclone separation efficiency was calculated, and the static pressure and velocity contours were plotted. The results showed the capability of the CFD-based simulation for an accurate demonstration of the behavior of the fluid–solid phase. Accordingly, it can be used to predict the efficiency of stigma separation from petals of saffron using airflow in the cyclone. According to the results, the highest cyclonic separation efficiency of 89% was achieved at an inlet air velocity of 3.5 m/s, which was very close to the experimental data.

scholarly journals Effects of Blade Parameters on the Flow Field and Classification Performance of the Vertical Roller Mill via Numerical Investigations

2020 ◽  
Vol 2020 ◽  
pp. 1-15
Author(s):  
Chang Liu ◽  
Zuobing Chen ◽  
Weili Zhang ◽  
Chenggang Yang ◽  
Ya Mao ◽  
...  
Keyword(s):  
Flow Field ◽  
Pressure Difference ◽  
Continuous Phase ◽  
Classification Performance ◽  
Field Analysis ◽  
Discrete Phase Model ◽  
Roller Mill ◽  
Discrete Phase ◽  
Vertical Roller ◽  
Classification Efficiency

The vertical roller mill is an important crushing and grading screening device widely used in many industries. Its classification efficiency and the pressure difference determine the entire producing capacity and power consumption, respectively, which makes them the two key indicators describing the mill performance. Based on the DPM (Discrete Phase Model) and continuous phase coupling model, the flow field characteristics in the vertical roller mill including the velocity and pressure fields and the discrete phase distributions had been analyzed. The influence of blade parameters like the shape, number, and rotating speed on the flow field and classification performance had also been comprehensively explored. The numerical simulations showed that there are vortices in many zones in the mill and the blades are of great significance to the mill performance. The blade IV not only results in high classification efficiency but also reduces effectively the pressure difference in the separator and also the whole machine. The conclusions of the flow field analysis and the blade effects on the classification efficiency and the pressure difference could guide designing and optimizing the equipment structure and the milling process, which is of great importance to obtain better overall performance of the vertical roller mill.

Numerical Analysis on the CO-NO Formation Production near Burner Throat in Swirling Flow Combustion System

2014 ◽  
Vol 69 (2) ◽  
Author(s):  
Mohamad Shaiful Ashrul Ishak ◽  
Mohammad Nazri Mohd Jaafar
Keyword(s):  
Swirling Flow ◽  
Reverse Flow ◽  
Flow Behavior ◽  
Recirculation Region ◽  
Mixing Enhancement ◽  
Ansys Fluent ◽  
Pressure Losses ◽  
No Formation ◽  
Swirl Angle ◽  
Air Mixing

The main purpose of this paper is to study the Computational Fluid Dynamics (CFD) prediction on CO-NO formation production inside the combustor close to burner throat while varying the swirl angle of the radial swirler. Air swirler adds sufficient swirling to the inlet flow to generate central recirculation region (CRZ) which is necessary for flame stability and fuel air mixing enhancement. Therefore, designing an appropriate air swirler is a challenge to produce stable, efficient and low emission combustion with low pressure losses. A liquid fuel burner system with different radial air swirler with 280 mm inside diameter combustor of 1000 mm length has been investigated. Analysis were carried out using four different radial air swirlers having 30°, 40°, 50° and 60° vane angles. The flow behavior was investigated numerically using CFD solver Ansys Fluent. This study has provided characteristic insight into the formation and production of CO and pollutant NO inside the combustion chamber. Results show that the swirling action is augmented with the increase in the swirl angle, which leads to increase in the center core reverse flow, therefore reducing the CO and pollutant NO formation. The outcome of this work will help in finding out the optimum swirling angle which will lead to less emission.  

A Preliminary Study of the Blade Erosion for a Wind Turbine Operating in a Dusty Environment

2016 ◽  
Author(s):  
Ahmed Hossam El-Din ◽  
Aya Diab
Keyword(s):  
Leading Edge ◽  
Particle Collision ◽  
Turbine Engines ◽  
Surface Erosion ◽  
Coal Slurry ◽  
Predictive Tool ◽  
Ansys Fluent ◽  
Flow Parameters ◽  
Discrete Phase Modeling ◽  
Discrete Phase

The process of surface erosion due to particle collision has been the focus of a number of investigations with regards to gas turbine engines, aircraft, reentry missiles, pipelines carrying coal slurry, etc. Recently, increased interest in wind energy by countries in the Saharan regions of the Middle East and North Africa (MENA) brings about some concern about leading edge erosion of wind turbines operating under such dusty conditions. Leading edge erosion can have a detrimental impact on the extracted energy as it changes the blade surface roughness causing premature/unpredictable separation. Though erosion may not be easily avoided; it may be mitigated via using airfoil families characterized by low roughness sensitivity. In this paper, a model of an airfoil erosion subjected to sand blasting is developed using the discrete phase modeling capability in ANSYS-FLUENT along with the DNV erosion model. The effect of various flow parameters, such as angle of attack, and particle size, on the extent of erosion is investigated for a number of airfoil designs. The developed model is used as a predictive tool to assess the power deterioration of eroded wind blades.

Computational Modeling of Particulate Pollutant Transport in a Ventilated Room in the Presence of Two Heated Breathing and Rotating Manikins

2017 ◽  
Author(s):  
Seyed Ali Keshavarz ◽  
Mazyar Salmanzadeh ◽  
Goodarz Ahmadi
Keyword(s):  
Air Quality ◽  
Computational Modeling ◽  
Indoor Air Quality ◽  
Indoor Air ◽  
Rotational Motion ◽  
Indoor Environment ◽  
Ventilation System ◽  
Thermal Plume ◽  
Displacement Ventilation ◽  
Simulation Results

Recently, attention has been given to indoor air quality due to its serious health concerns. Clearly the dispersion of pollutant is directly affected by the airflow patterns. The airflow in indoor environment is the results of a combination of several factors. In the present study, the effects of thermal plume and respiration on the indoor air quality in a ventilated cubicle were investigated using an unsteady computational modeling approach. The person-to-person contaminant transports in a ventilated room with mixing and displacement ventilation systems were studied. The effects of rotational motion of the heated manikins were also analyzed. Simulation results showed that in the cases which rotational motion was included, the human thermal plume and associated particle transport were significantly distorted. The distortion was more noticeable for the displacement ventilation system. Also it was found that the displacement ventilation system lowered the risk of person-to-person transmission in an office space in comparison with the mixing ventilation system. On the other hand the mixing system was shown to be more effective compared to the displacement ventilation in removing the particles and pollutant that entered the room through the inlet air diffuser.

Unsteady Modeling of Powdered Activated Carbon Deposition on Collection Electrode of a Lab-Scale Electrostatic Precipitator (ESP)

2012 ◽  
Author(s):  
Yasmin Khakpour ◽  
Herek L. Clack
Keyword(s):  
Activated Carbon ◽  
Particle Deposition ◽  
Electrostatic Precipitator ◽  
Activated Carbons ◽  
Collection Efficiency ◽  
Continuous Phase ◽  
Powdered Activated Carbon ◽  
Computational Domain ◽  
Discrete Phase Model ◽  
Discrete Phase

Particulate sampling in the flue gas at the Electrostatic Precipitator (ESP) outlet during injection of powdered activated carbons (PACs) has provided strong anecdotal evidence indicating that injected PACs can penetrate the ESP in significant concentrations. The low resistivity of PAC is consistent with poor collection efficiency in an ESP and lab-scale testing has revealed significantly different collection behavior of PAC in an ESP as compared to fly ash. The present study illustrates the use of a commercial CFD package — FLUENT — to investigate precipitation of powdered activated carbon (PAC) in the presence and absence of electric field. The computational domain is designed to represent a 2-D wire-plate ESP channel. The governing equations include those covering continuous phase transport, electric potential, air ionization, and particle charging. The particles are tracked using a Lagrangian Discrete Phase Model (DPM). In addition, a custom user-defined function (UDF) uses a deforming boundary condition and a prescribed critical particle velocity to account for particle deposition and dust-cake growth on the electrodes. The effect of Electrohydrodynamics (EHD) induced flow on the ESP collection efficiency under various flow and particle characteristics as well as different ESP configurations are illustrated.

scholarly journals Three-Dimensional Simulation of Wind-Driven Ventilation Through a Windcatcher With Different Inlet Designs

2019 ◽  
Vol 12 (4) ◽  
Author(s):  
Peter Abdo ◽  
Rahil Taghipour ◽  
B. Phuoc Huynh
Keyword(s):  
Wind Speed ◽  
Average Velocity ◽  
Natural Ventilation ◽  
Ventilation System ◽  
Three Dimensional ◽  
Cfd Modeling ◽  
Ansys Fluent ◽  
Wind Velocities ◽  
Dimensional Simulation ◽  
Convergent Inlet

Abstract Windcatcher is an effective natural ventilation system, and its performance depends on several factors including wind speed and wind direction. It provides a comfortable and healthy indoor environment since the introduced fresh air decreases the moisture content and reduces the pollutant concentration. Since the wind speed and its direction are generally unpredictable, it is important to use special inlet forms and exits to increase the efficiency of a windcatcher. In this study, computational fluid dynamics (CFD) modeling is implemented using ansys fluent to investigate the airflow entering a three-dimensional room through a windcatcher with different inlet designs. Three designs are studied which are a uniform inlet, a divergent inlet, and a bulging-convergent inlet. The airflow pattern with all inlets provided adequate ventilation through the room. With all the applied wind velocities (1, 2, 3, and 6 m/s) at the domain's inlet, the divergent inlet shape has captured the highest airflow through the room and provided higher average velocity at 1.2 m high enhancing the thermal comfort where most of the human occupancy occurs. With 6 m/s wind velocity, the divergent inlet has captured 2.55% more flow rate compared to the uniform inlet and 4.70% compared to the bulging-convergent inlet, and it has also provided an average velocity at 1.2 m high in the room of 7.16% higher than the uniform inlet and 8.44% higher than the bulging-convergent inlet.

scholarly journals MODELING COMPUTATIONAL FLUID DYNAMICS OF MULTIPHASE FLOWS IN ELBOW AND T-JUNCTION OF THE MAIN GAS PIPELINE

Transport ◽  
2019 ◽  
Vol 34 (1) ◽  
pp. 19-29 ◽  
Author(s):  
Yaroslav Doroshenko ◽  
Julia Doroshenko ◽  
Vasyl Zapukhliak ◽  
Lyubomyr Poberezhny ◽  
Pavlo Maruschak
Keyword(s):  
Natural Gas ◽  
Multiphase Flows ◽  
Linear Part ◽  
Erosive Wear ◽  
Gas Pipeline ◽  
Solid Particles ◽  
Ansys Fluent ◽  
Gas Main ◽  
Discrete Phase ◽  
Main Gas Pipeline

The research was performed in order to obtain the physical picture of the movement of condensed droplets and solid particles in the flow of natural gas in elbows and T-junctions of the linear part of the main gas pipeline. 3D modeling of the elbow and T-junction was performed in the linear part of the gas main, in particular, in places where a complex movement of multiphase flows occurs and changes its direction. In these places also occur swirls, collisions of discrete phases in the pipeline wall, and erosive wear of the pipe wall. Based on Lagrangian approach (Discrete Phase Model – DPM), methods of computer modeling were developed to simulate multiphase flow movement in the elbow and T-junction of the linear part of the gas main using software package ANSYS Fluent R17.0 Academic. The mathematical model is based on solving the Navier–Stokes equations, and the equations of continuity and discrete phase movement closed with Launder–Sharma (k–e) two-parameter turbulence model with appropriate initial and boundary conditions. In T-junction, we simulated gas movement in the run-pipe, and the passage of the part of flow into the branch. The simulation results were visualized in postprocessor ANSYS Fluent R17.0 Academic and ANSYS CFD-Post R17.0 Academic by building trajectories of the motion of condensed droplets and solid particles in the elbow and T-junction of the linear part of the gas main in the flow of natural gas. The trajectories were painted in colors that match the velocity and diameter of droplets and particles according to the scale of values. After studying the trajectories of discrete phases, the locations of their heavy collision with the pipeline walls were found, as well as the places of turbulence of condensed droplets and solid particles. The velocity of liquid and solid particles was determined, and the impact angles, diameters of condensed droplets and solid particles in the place of collision were found. Such results provide possibilities for a full and comprehensive investigation of erosive wear of the elbow and T-junction of the linear part of the gas main and adjacent sections of the pipeline, and for the assessment of their strength and residual life.

scholarly journals Perancangan Desain User Interface Aplikasi KABITA Untuk Menginformasikan Kuliner Street Food Kota BandungTION TO INFORM INFORMATION STREET FOOD CULINARY BANDUNG CITY

2020 ◽  
Vol 3 (1) ◽  
pp. 26-40
Author(s):  
Diwan Setiawan ◽  
Sri Wulandari
Keyword(s):  
User Interface ◽  
Interface Design ◽  
Rapid Development ◽  
Field Studies ◽  
Street Food ◽  
City Street ◽  
Long Time ◽  
The Media ◽  
Information Media ◽  
The City

Bandung is a city that has a variety of culinary, it makes this city as a culinary tourism destination that highly demanded by both domestic and foreign tourists. Based on data from the Department of Culture and Tourism of Bandung, Bandung has a legendary street food culinary that is highly favored by culinary enthusiasts who visit this city. Street food culinary is snacks that have been around for a long time with authentic flavors and stories behind, some of popular street food culinary are bandros, combro, colenak, ketan bakar, cireng ​​and others. The rapid development of culinary potential in this city has caused many new street foods that enriches culinary diversity in Bandung so that culinary enthusiasts need an information media contains of information about culinary in this city, especially authentic street food culinary which is starting to be hard to find. Through qualitative methods and data collection techniques by means of field studies such as observation, interviews and questionnaires, it is necessary to design an application-based information media. The final results of this research is user interface design for the media that informs Bandung street food culinary. Inspired by the word kabita which comes from Sundanese means tempted to taste food, was chosen as the name of the application that informs culinary street food in the city of Bandung that aims to facilitate culinary enthusiasts to get that information

Sign in / Sign up

Export Citation Format

Share Document