A Study on Impeller-Diffuser Interaction: Part I — Influence on the Performance

2002 ◽  
Author(s):  
Kai U. Ziegler ◽  
Heinz E. Gallus ◽  
Reinhard Niehuis
Keyword(s):  
Strong Influence ◽  
Vaned Diffuser ◽  
Flow Losses ◽  
Extensive Test ◽  
Radial Gap ◽  
Operating Points ◽  
Vane Angle ◽  
Compressor Efficiency ◽  
Probe Measurements ◽  
Highly Loaded

The interaction between impeller and diffuser is considered to have strong influence on the flow in highly loaded centrifugal compressors. However, the knowledge about this influence is still not satisfying. This two-part paper presents an experimental investigation of the effect of impeller-diffuser interaction on the unsteady and the time averaged flow configuration in impeller and diffuser and the performance of these components. The flat wedge vaned diffuser of the investigated stage allows an independent adjustment of diffuser vane angle and radial gap between impeller exit and diffuser vane inlet. Attention is mainly directed to the radial gap, as it determines the intensity of the impeller-diffuser interaction. Part I deals with the integral flow losses and the diffusion in impeller, diffuser and the entire compressor. An extensive test series with steady probe measurements at impeller exit and diffuser exit was performed at 10 different diffuser geometries and different operating points. The results show that in most cases smaller radial gaps are leading to a more homogeneous flow field at diffuser vane exit and to a higher diffuser pressure recovery resulting in a higher compressor efficiency. On the other hand, impeller efficiency is hardly affected by the radial gap. In part II measurements with a laser-2-focus velocimeter are presented illuminating the reasons for the effects found. The experimental results are intended to be published as an open CFD testcase under the name “Radiver”.

A Study on Impeller-Diffuser Interaction—Part I: Influence on the Performance

2003 ◽  
Vol 125 (1) ◽  
pp. 173-182 ◽  
Author(s):  
Kai U. Ziegler ◽  
Heinz E. Gallus ◽  
Reinhard Niehuis
Keyword(s):  
Flow Field ◽  
Field Configuration ◽  
Test Case ◽  
Vaned Diffuser ◽  
Flow Losses ◽  
Extensive Test ◽  
Radial Gap ◽  
Operating Points ◽  
Vane Angle ◽  
Probe Measurements

The interaction between impeller and diffuser is considered to have strong influence on the flow in centrifugal compressors. However, the knowledge about this influence is still not satisfying. This two-part paper presents an experimental investigation of the effect of impeller-diffuser interaction on the unsteady and the time averaged flow field configuration in impeller and diffuser and the performance of these components. The flat wedge vaned diffuser of the investigated compressor allows an independent adjustment of diffuser vane angle and radial gap between impeller exit and diffuser vane inlet. Attention is mainly directed to the radial gap, as it determines the intensity of the impeller-diffuser interaction. Part I deals with the integral flow losses and the diffusion in impeller, diffuser and the entire compressor. An extensive test series with steady probe measurements at impeller exit and diffuser exit was performed at 10 different diffuser geometries and different operating points. The results show that in most cases smaller radial gaps are leading to a more homogeneous flow field at diffuser vane exit and to a higher diffuser pressure recovery resulting in a higher compressor efficiency. On the other hand, impeller efficiency is hardly affected by the radial gap. In Part II, measurements with a laser-2-focus velocimeter are presented illuminating the reasons for the effects found. The experimental results are published as an open CFD test case under the name “Radiver.”

A Study on Impeller-Diffuser Interaction: Part II — Detailed Flow Analysis

2002 ◽  
Author(s):  
Kai U. Ziegler ◽  
Heinz E. Gallus ◽  
Reinhard Niehuis
Keyword(s):  
Strong Influence ◽  
Flow Analysis ◽  
Pressure Side ◽  
Wake Region ◽  
Vaned Diffuser ◽  
Flow Configuration ◽  
Noticeable Reduction ◽  
Radial Gap ◽  
Vane Angle ◽  
Highly Loaded

The interaction between impeller and diffuser is considered to have strong influence on the flow in highly loaded centrifugal compressors. However, the knowledge about this influence is still not satisfying. This two-part paper presents an experimental investigation of the effect of impeller-diffuser interaction on the unsteady and the time averaged flow configuration in impeller and diffuser and the performance of these components. The flat wedge vaned diffuser of the investigated stage allows an independent adjustment of diffuser vane angle and radial gap between impeller exit and diffuser vane inlet. Attention is mainly directed to the radial gap, as it determines the intensity of the impeller-diffuser interaction. In part I it was shown that smaller radial gaps improve diffuser pressure recovery, whereas impeller efficiency is hardly affected. Part II focuses on the reasons for these effects. Measurements with a laser-2-focus velocimeter in the highly unsteady flow field between the impeller exit region and diffuser throat were performed at three different diffuser geometries allowing a detailed flow analysis. Especially the unsteady results show that for a smaller radial gap more impeller wake fluid is conveyed towards the highly loaded diffuser vane pressure side reducing its loading and leading to a better diffusion in the diffuser channel. Concerning the impeller flow, it was found that a smaller radial gap is leading to a noticeable reduction of the wake region at impeller exit. The experimental results are intended to be published as an open CFD testcase under the name “Radiver”.

A Study on Impeller-Diffuser Interaction—Part II: Detailed Flow Analysis

2003 ◽  
Vol 125 (1) ◽  
pp. 183-192 ◽  
Author(s):  
Kai U. Ziegler ◽  
Heinz E. Gallus ◽  
Reinhard Niehuis
Keyword(s):  
Flow Field ◽  
Strong Influence ◽  
Flow Analysis ◽  
Test Case ◽  
Wake Region ◽  
Vaned Diffuser ◽  
Noticeable Reduction ◽  
Radial Gap ◽  
Vane Angle ◽  
Highly Loaded

The interaction between impeller and diffuser is considered to have strong influence on the flow in centrifugal compressors. However, the knowledge about this influence is still not satisfying. This two-part paper presents an experimental investigation of the effect of impeller-diffuser interaction on the unsteady and the time-averaged flow field in impeller and diffuser and the performance of these components. The flat wedge vaned diffuser of the investigated compressor allows an independent adjustment of diffuser vane angle and radial gap between impeller exit and diffuser vane inlet. Attention is mainly directed to the radial gap, as it determines the intensity of the impeller-diffuser interaction. In Part I it was shown that smaller radial gaps improve diffuser pressure recovery, whereas impeller efficiency is hardly affected. Part II focuses on the reasons for these effects. Measurements with a laser-2-focus velocimeter in the highly unsteady flow field between the impeller exit region and diffuser throat were performed at three different diffuser geometries allowing a detailed flow analysis. Especially the unsteady results show that for a smaller radial gap more impeller wake fluid is conveyed towards the highly loaded diffuser vane pressure side reducing its loading and leading to a better diffusion in the diffuser channel. Concerning the impeller flow, it was found that a smaller radial gap is leading to a noticeable reduction of the wake region at impeller exit. The experimental results are intended to be published as an open CFD test case under the name “Radiver.”

A Numerical Study on Performances of Centrifugal Compressor Stages With Different Radial Gaps

2000 ◽  
Author(s):  
K. Sato ◽  
L. He
Keyword(s):  
Centrifugal Compressor ◽  
Stokes Equations ◽  
Numerical Study ◽  
Axial Compressor ◽  
Navier Stokes ◽  
Centrifugal Impeller ◽  
Vaned Diffuser ◽  
Navier Stokes Equations ◽  
Performance Predictions ◽  
Radial Gap

A numerical study of 3D unsteady flows in centrifugal compressor stages solving the Navier-Stokes equations is presented. The emphasis is on the effect of the radial gap between blade rows on the aerodynamic performance. In the numerical tests, Krain’s centrifugal impeller was combined with a DCA (Double Circular Arc) type radial vaned diffuser. The compressor stages with three settings of radial gap ranging from 5 to 15 percent of the impeller trailing edge radius are configured and unsteady flow simulations are carried out to compare the time-averaged efficiencies. The performance predictions show that the efficiency is deteriorated if the radial gap between blade rows is reduced with intensified blade row interaction, which is in contradiction to the general trend for axial compressor stages. In the centrifugal compressors tested, wake chopping by diffuser vanes, which usually benefits efficiency in axial compressor stages, causes unfavourable wake compression through the diffuser passages to deteriorate the efficiency.

Centrifugal Compressor of a 100 kW Microturbine: Part 1 — Experimental and Numerical Investigations on Overall Performance

2003 ◽  
Author(s):  
E. Benini ◽  
A. Toffolo ◽  
A. Lazzaretto
Keyword(s):  
Numerical Model ◽  
Centrifugal Compressor ◽  
Small Scale ◽  
Turbine Engine ◽  
Sliding Mesh ◽  
Extensive Test ◽  
Rotor Stator Interaction ◽  
Compressor Performance ◽  
True Time ◽  
Operating Points

This paper describes on/off design performance of a centrifugal compressor of a 100 kW turbogenerator gas turbine engine used for small scale power generation. The compressor stage is made up of a radial impeller and a two-stage diffuser (radial and deswirl). Part 1 deals with the experimental and numerical tests on overall compressor and diffuser performance: An extensive test series with steady probe measurements at impeller exit and diffuser exit is performed at different operating points and rotational speeds. This makes it possible to characterize both overall compressor and diffuser. The numerical model is based on a mixing plane at impeller-diffuser interface and therefore neglects the effect of unsteadiness due to rotor-stator interaction. Then, in part 2 the true time-dependent interaction is investigated by means of a numerical model where a sliding mesh technique is adopted. The unsteady results are then processed and compared with the steady ones regarding the flow in the diffuser. Finally, in part 3 the geometry of the compressor diffuser is optimized using an evolutionary algorithm coupled with a CFD code in order to improve compressor performance.

Experimental Investigation of the Diffuser Vane Clearance Effect in a Centrifugal Compressor Stage With Adjustable Diffuser Geometry: Part II—Detailed Flow Analysis

2014 ◽  
Vol 137 (3) ◽  
Author(s):  
Stefan Ubben ◽  
Reinhard Niehuis
Keyword(s):  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Flow Analysis ◽  
Industrial Applications ◽  
Experimental Investigations ◽  
Stall Margin ◽  
Diffuser Flow ◽  
Radial Gap ◽  
The Impact ◽  
Vane Angle

Adjustable diffuser vanes offer an attractive design option for centrifugal compressors applied in industrial applications. However, the knowledge about the impact on compressor performance of a diffuser vane clearance between vane and diffuser wall is still not satisfying. This two-part paper summarizes results of experimental investigations performed with an industrial-like centrifugal compressor. Particular attention was directed toward the influence of the diffuser clearance on the operating behavior of the entire stage, the pressure recovery in the diffuser, and on the diffuser flow by a systematic variation of the parameters diffuser clearance height, diffuser vane angle, radial gap between impeller exit and diffuser inlet, and rotor speed. In Part I it was shown that an one-sided diffuser clearance is able to contribute to an increase in flow range, stall margin, pressure ratio, and efficiency. In order to reveal the relevant flow phenomena, in Part II the results of detailed measurements of the pressure distribution at diffuser exit and particle image velocimetry (PIV) measurements inside the diffuser channel performed at three clearance configurations and three diffuser angles at a fixed radial gap are discussed. It was found that, for defined diffuser configurations, the clearance flow amplifies the diffuser throat vortex capable to reduce the loading of the highly loaded vane pressure side and to support a more homogenous diffuser flow. It turned out that the co-action of the geometry parameter diffuser vane angle and diffuser clearance height is of particular importance. The experimental results are published as an open computational fluid dynamics (CFD) testcase “Radiver 2.”

Impeller Rotating Stall as a Trigger for the Transition From Mild to Deep Surge in a Subsonic Centrifugal Compressor

1993 ◽  
Author(s):  
Beat Ribi ◽  
Georg Gyarmathy
Keyword(s):  
Mach Number ◽  
Mass Flow Rate ◽  
Flow Rate ◽  
Centrifugal Compressor ◽  
Critical Value ◽  
Rotating Stall ◽  
Vaned Diffuser ◽  
Time Resolved ◽  
Compressor Map ◽  
Operating Points

The present paper concerns the transition from mild to deep surge in a single stage centrifugal compressor using a vaned diffuser. Time-resolved measurements of the mass flow rate and the static pressures at various locations of the compressor were analyzed for different diffuser geometries and different operating points in the compressor map. When the throttle valve was gradually closed at an impeller tip Mach number (Mu) above 0.4, the compressor showed first mild and then deep surge whereas at Mu=0.4 rotating stall was the dominant instability. This single-cell rotating stall was identified to be caused by the impeller. During mild surge at higher Mach numbers the instantaneous flow and pressure traces showed that the overall flow at the stage inlet intermittently dropped below the critical value associated with the occurence of impeller rotating stall. Rotating stall appeared for a while but vanished as soon as the flow increased again. With further throttling, however, a threshold was reached at which rotating stall triggered deep surge. The results show that triggering only occurred if the flow deficiency causing rotating stall persisted long enough to permit the stall cell to make at least one or two revolutions.

scholarly journals Effects of Radial Gap Ratio between Impeller and Vaned Diffuser on Performance of Centrifugal Compressors

2017 ◽  
Vol 7 (7) ◽  
pp. 728 ◽  
Author(s):  
Mohammadjavad Hosseini ◽  
Zhenzhong Sun ◽  
Xiao He ◽  
Xinqian Zheng
Keyword(s):  
Centrifugal Compressors ◽  
Vaned Diffuser ◽  
Gap Ratio ◽  
Radial Gap

scholarly journals Experimental Investigation of Unsteady Flow Phenomena in a Centrifugal Compressor Vaned Diffuser of Variable Geometry

1999 ◽  
Vol 121 (4) ◽  
pp. 763-771 ◽  
Author(s):  
F. Justen ◽  
K. U. Ziegler ◽  
H. E. Gallus
Keyword(s):  
Centrifugal Compressor ◽  
Pressure Fluctuations ◽  
Suction Side ◽  
Front Wall ◽  
Compressor Stage ◽  
Vaned Diffuser ◽  
Centrifugal Compressor Stage ◽  
Impeller Outlet ◽  
Flow Phenomena ◽  
Radial Gap

The behavior of vaned radial diffusers is generally considered to be due to the flow phenomena in the vaneless and the semi-vaned space in the diffuser inlet region. Even considering unsteady aspects, the adjacent diffuser channel is regarded as less important. The flat wedge vaned diffuser of the centrifugal compressor stage investigated allows an independent continuous adjustment of the diffuser vane angle and the radial gap between impeller outlet and diffuser vane inlet, so that information about the importance of these geometric parameters can be obtained. The time-dependent pressure distribution on the diffuser front wall and on the suction and pressure surfaces of the diffuser vanes reveal that in the semi-vaned space mainly the region near the vane suction side is influenced by the unsteady impeller-diffuser interaction. Downstream in the diffuser channel the unsteadiness does not decay. Here, pressure fluctuations are appearing that are distinctly higher than the pressure fluctuations in the vaneless space. An estimation of the influence of the unsteadiness on the operating performance of the centrifugal compressor stage is made by measurements at choke and surge limit for different diffuser geometries.

Sign in / Sign up

Export Citation Format

Share Document