Rolls Royce/Allison 501-K Gas Turbine: Anti-Fouling Compressor Coatings Shipboard — Phase I

2003 ◽  
Author(s):  
Daniel E. Caguiat ◽  
David M. Zipkin ◽  
Jeffrey S. Patterson
Keyword(s):  
Gas Turbine ◽  
United States Navy ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Time Data ◽  
Turbine Generator ◽  
Turbine Engine ◽  
Test Engine ◽  
Compressor Performance ◽  
Naval Surface Warfare

Naval Surface Warfare Center Carderock Division (NSWCCD) Gas Turbine Emerging Technologies Code 9334 conducted a land-based evaluation of fouling-resistant compressor coatings for the 501-K17 Ship Service Gas Turbine Generator (SSGTG) [1]. The purpose of this evaluation was to determine whether such coatings could be used to decrease the rate of compressor fouling and associated fuel consumption. Based upon favorable results from the land-based evaluation, a similar coated compressor gas turbine engine was installed onboard a United States Navy vessel. Two data acquisition computer (DAC) systems and additional sensors necessary to monitor and compare both the coated test engine and an uncoated control engine were added. The goal of this shipboard evaluation was to verify land-based results in a shipboard environment. Upon completion of the DAC installation, the two gas turbine engines were operated and initial data was stored. Shipboard data was compared to land-based data to verify validity and initial compressor performance. The shipboard evaluation is scheduled for completion in June 2003, at which time data will be analyzed and results published.

Case Closed: The Completion of the United States Navy 501-K34 Gas Turbine Engine RADCON Program (2011 - 2019)

2021 ◽  
Author(s):  
Jeffrey S. Patterson ◽  
Kevin Fauvell ◽  
Dennis Russom ◽  
Willie A. Durosseau ◽  
Phyllis Petronello ◽  
...  
Keyword(s):  
United States ◽  
Gas Turbine ◽  
United States Navy ◽  
The United States ◽  
Gas Turbine Engine ◽  
United States Government ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Turbine Engine ◽  
The U.S

Abstract The United States Navy (USN) 501-K Series Radiological Controls (RADCON) Program was launched in late 2011, in response to the extensive damage caused by participation in Operation Tomodachi. The purpose of this operation was to provide humanitarian relief aid to Japan following a 9.0 magnitude earthquake that struck 231 miles northeast of Tokyo, on the afternoon of March 11, 2011. The earthquake caused a tsunami with 30 foot waves that damaged several nuclear reactors in the area. It was the fourth largest earthquake on record (since 1900) and the largest to hit Japan. On March 12, 2011, the United States Government launched Operation Tomodachi. In all, a total of 24,000 troops, 189 aircraft, 24 naval ships, supported this relief effort, at a cost in excess of $90.0 million. The U.S. Navy provided material support, personnel movement, search and rescue missions and damage surveys. During the operation, 11 gas turbine powered U.S. warships operated within the radioactive plume. As a result, numerous gas turbine engines ingested radiological contaminants and needed to be decontaminated, cleaned, repaired and returned to the Fleet. During the past eight years, the USN has been very proactive and vigilant with their RADCON efforts, and as of the end of calendar year 2019, have successfully completed the 501-K Series portion of the RADCON program. This paper will update an earlier ASME paper that was written on this subject (GT2015-42057) and will summarize the U.S. Navy’s 501-K Series RADCON effort. Included in this discussion will be a summary of the background of Operation Tomodachi, including a discussion of the affected hulls and related gas turbine equipment. In addition, a discussion of the radiological contamination caused by the disaster will be covered and the resultant effect to and the response by the Marine Gas Turbine Program. Furthermore, the authors will discuss what the USN did to remediate the RADCON situation, what means were employed to select a vendor and to set up a RADCON cleaning facility in the United States. And finally, the authors will discuss the dispensation of the 501-K Series RADCON assets that were not returned to service, which include the 501-K17 gas turbine engine, as well as the 250-KS4 gas turbine engine starter. The paper will conclude with a discussion of the results and lessons learned of the program and discuss how the USN was able to process all of their 501-K34 RADCON affected gas turbine engines and return them back to the Fleet in a timely manner.

LM2500 Reliability Improvements for United States Navy Applications

2000 ◽  
Author(s):  
Matthew Driscoll ◽  
Thomas Habib ◽  
William Arseneau
Keyword(s):  
United States ◽  
Gas Turbine ◽  
United States Navy ◽  
The United States ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Turbine Engine ◽  
Standard Configuration ◽  
Program Plan ◽  
Improve Reliability

The United States Navy uses the General Electric LM2500 gas turbine engine for main propulsion on its newest surface combatants including the OLIVER HAZARD PERRY (FFG 7) class frigates, SPRUANCE (DD 963) class destroyers, TICONDEROGA (CG 47) class cruisers, ARLIEGH BURKE (DDG 51) class destroyers and SUPPLY (AOE 6) class oilers. Currently, the Navy operates a fleet of over 400 LM2500 gas turbine engines. This paper discusses the ongoing efforts to characterize the availability of the engines aboard ship and pinpoint systems/components that have significant impact on engine reliability. In addition, the program plan to upgrade the LM2500’s standard configuration to improve reliability is delineated.

Advanced Degradation Rates for High Power LM2500 Applications

2006 ◽  
Author(s):  
Matthew J. Driscoll ◽  
Thomas Habib
Keyword(s):  
Gas Turbine ◽  
High Power ◽  
United States Navy ◽  
The United States ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Design Phase ◽  
Turbine Engine ◽  
Operational Profile ◽  
Degradation Rates

Since the early 1970’s, the United States Navy has utilized the General Electric LM2500 gas turbine engine for propulsion aboard its surface combatants including its newest DDG 51 Class Destroyer. These ships have generally operated at a part power operational profile under a COGAG arrangement which has offered system redundancy while exceeding life projections for the gas turbine engines. For its newest ships still in the design phase (LHD 8/LCS/LSC(X)) the Navy intends to continue to utilize gas turbine engines but in different applications including electric drive, high power boost applications in tandem with both diesel engines and electric motor arrangements. Although this paper focuses on the LM2500, its conclusions are meant to apply to a broader scope of future propulsion applications. Specific conclusions are provided describing potential operating profile considerations.

Compressor Fouling Testing on Rolls Royce/Allison 501-K17 and General Electric LM2500 Gas Turbine Engines

2002 ◽  
Author(s):  
Daniel E. Caguiat ◽  
David M. Zipkin ◽  
Jeffrey S. Patterson
Keyword(s):  
Gas Turbine ◽  
Fuel Economy ◽  
Gas Turbines ◽  
Turbine Engines ◽  
Data Sets ◽  
Gas Turbine Engines ◽  
Test Plan ◽  
General Electric ◽  
Compressor Performance ◽  
Naval Surface Warfare

As part of the Gas Turbine Condition Based Maintenance (CBM) Program, Naval Surface Warfare Center, Carderock Division Code 9334 conducted compressor fouling testing on the General Electric LM2500 and Rolls Royce/Allison 501-K Series gas turbines. The objective of these tests was to determine the feasibility of quantifying compressor performance degradation using existing and/or added engine sensors. The end goal of these tests will be to implement an algorithm in the Navy Fleet that will determine the optimum time to detergent crank wash each gas turbine based upon compressor health, fuel economy and other factors which must be determined. Fouling tests were conducted at the Land Based Engineering Site (LBES). For each gas turbine, the test plan that was utilized consisted of injecting a salt solution into the gas turbine inlet, gathering compressor performance and fuel economy data, analyzing the data to verify sensor trends, and assessing the usefulness of each parameter in determining compressor and overall gas turbine health. Based upon data collected during these fouling tests, it seems feasible to accomplish the end goal. Impact Technologies, who analyzed the data sets for both of these fouling tests, has developed a prognostic modeling approach for each of these gas turbines using a combination of the data and probabilistic analysis.

United States Navy 501-K34 Gas Turbine Engine RADCON Effort

2015 ◽  
Author(s):  
Jeffrey S. Patterson ◽  
Kevin D. Fauvell ◽  
Jay McMahon ◽  
Javier O. Moralez
Keyword(s):  
United States ◽  
Gas Turbine ◽  
United States Navy ◽  
The United States ◽  
United States Government ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Humanitarian Relief ◽  
Turbine Engine ◽  
The U.S

On the afternoon of March 11, 2011 at 2:46pm, a 9.0 magnitude earthquake took place 231 miles northeast of Tokyo, Japan, at a depth of 15.2 miles. The earthquake caused a tsunami with 30 foot waves that damaged several nuclear reactors in the area. It was the fourth largest earthquake on record (since 1900) and the largest to hit Japan. On March 12, 2011, the United States Government launched Operation Tomodachi to provide humanitarian relief aid to Japan. In all, a total of 24,000 troops, 189 aircraft, 24 naval ships, supported this relief effort, at a cost of $90.0 million. The U.S. Navy provided material support, personnel movement, search and rescue missions and damage surveys. During the operation, 11 gas turbine U.S. warships operated within the radioactive plume. As a result, numerous gas turbine engines ingested radiological contaminants and are now operating under Radiological Controls (RADCON). This paper will describe the events that lead to Operation Tomodachi, as well as the resultant efforts on the U.S. Navy’s Japanese based gas turbine fleet. In addition, this paper will outline the U.S. Navy’s effort to decontaminate, overhaul and return these RADCON assets back into the fleet.

Low Emissions Microgrid Power Fueled by Bakken Flare Gas

2014 ◽  
Author(s):  
Richard J. Roby ◽  
Maclain M. Holton ◽  
Michael S. Klassen ◽  
Leo D. Eskin ◽  
Richard J. Joklik ◽  
...  
Keyword(s):  
Power Generation ◽  
Natural Gas ◽  
Gas Turbine ◽  
Liquid Fuels ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Turbine Engine ◽  
Test Engine ◽  
Combustion Technology ◽  
Drilling Operations

It is estimated that 30% of the over 1 billion cubic feet per day of natural gas produced in the Bakken shale field is lost to flaring. This flared gas, were it to be collected and used in DLE power generation gas turbine engines, represents approximately 1.2 GW of collective electric power. The main reason that much of this gas is flared is that the infrastructure in the Bakken lacks sufficient capacity or compression to combine and transport the gas streams. One of the reasons that this gas cannot be utilized on-site for power generation is that it contains significant amounts of natural gas liquids (NGLs) which make the gas unsuitable as a fuel for natural gas-fired gas turbine engines. A Lean, Premixed, Prevaporized (LPP) combustion technology has been developed that converts liquid fuels into a substitute for natural gas. This LPP Gastm can then be used to fuel virtually any combustion device in place of natural gas, yielding emissions comparable to those of ordinary natural gas. The LPP technology has been successfully demonstrated in over 1,000 hours of clean power generation on a 30 kW Capstone C30 microturbine. To date, 15 different liquid fuels have been vaporized and burned in the test gas turbine engine. To simulate the vaporization of NGLs, liquids including propane, pentane, and naphtha, among other liquids, have been vaporized and blended with methane. Emissions from the burning of these vaporized liquid fuels in the test engine have been comparable to baseline emissions from ordinary natural gas of 3 ppm NOx and 30 ppm CO. Autoignition of the vaporized liquid fuels in the gas turbine is controlled by the fraction of inert diluent added in the vaporization process. The LPP technology is able to process an infinitely variable composition of NGL components in the fuel stream by continually adjusting the amount of dilution to maintain a heating value consistent with natural gas. Burning the flare gases containing NGLs from a well locally, in a power generation gas turbine, would provide electricity for drilling operations. A microgrid can distribute power locally to the camps and infrastructure supporting the drilling and processing operations. Using the flare gases on-site has the benefit of reducing or eliminating the need for diesel tankers to supply fuel for power generation systems and equipment associated with the drilling operations.

Design, Development and Application of Vehicle Gas Turbine Engines

1966 ◽  
Vol 181 (1) ◽  
pp. 149-172
Author(s):  
P. A. Phillips ◽  
Peter Spear
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Low Cost ◽  
Engine Performance ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Design Development ◽  
Turbine Engine ◽  
Wide Range ◽  
Cycle Temperature

After briefly summarizing worldwide automotive gas turbine activity, the paper analyses the power plant requirements of a wide range of vehicle applications in order to formulate the design criteria for acceptable vehicle gas turbines. Ample data are available on the thermodynamic merits of various gas turbine cycles; however, the low cost of its piston engine competitor tends to eliminate all but the simplest cycles from vehicle gas turbine considerations. In order to improve the part load fuel economy, some complexity is inevitable, but this is limited to the addition of a glass ceramic regenerator in the 150 b.h.p. engine which is described in some detail. The alternative further complications necessary to achieve satisfactory vehicle response at various power/weight ratios are examined. Further improvement in engine performance will come by increasing the maximum cycle temperature. This can be achieved at lower cost by the extension of the use of ceramics. The paper is intended to stimulate the design application of the gas turbine engine.

Method for Operational Diagnostics of the Prepumping State of Gas Turbine Engines Based on Invariants of Acoustic Processes

NDT World ◽  
2021 ◽  
pp. 58-61
Author(s):  
Aleksey Popov ◽  
Aleksandr Romanov
Keyword(s):  
Gas Turbine ◽  
Acoustic Signal ◽  
Acoustic Method ◽  
Random Processes ◽  
Rotating Stall ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Turbine Engine ◽  
Software Complex ◽  
Operational Diagnostics

A large number of aviation events are associated with the surge of gas turbine engines. The article analyzes the existing systems for diagnostics of the surge of gas turbine engines. An analysis of the acoustic signal of a properly operating gas turbine engine was carried out, at which a close theoretical distribution of random values was determined, which corresponds to the studied distribution of the amplitudes of the acoustic signal. An invariant has been developed that makes it possible to evaluate the development of rotating stall when analyzing the acoustic signal of gas turbine engines. A method is proposed for diagnosing the pre-surge state of gas turbine engines, which is based on processing an acoustic signal using invariant dependencies for random processes. A hardware-software complex has been developed using the developed acoustic method for diagnosing the pre-surge state of gas turbine engines.

Practical Implications of Integrating Turbomachinery Into the Air Turborocket

2004 ◽  
Author(s):  
Joshua A. Clough ◽  
Mark J. Lewis
Keyword(s):  
Gas Turbine ◽  
Aircraft Engine ◽  
Launch Vehicle ◽  
Turbine Engines ◽  
Inlet Temperature ◽  
Gas Turbine Engines ◽  
Turbine Inlet Temperature ◽  
Turbine Engine ◽  
Space Launch ◽  
Practical Implications

The development of new reusable space launch vehicle concepts has lead to the need for more advanced engine cycles. Many two-stage vehicle concepts rely on advanced gas turbine engines that can propel the first stage of the launch vehicle from a runway up to Mach 5 or faster. One prospective engine for these vehicles is the Air Turborocket (ATR). The ATR is an innovative aircraft engine flowpath that is intended to extend the operating range of a conventional gas turbine engine. This is done by moving the turbine out of the core engine flow, alleviating the traditional limit on the turbine inlet temperature. This paper presents the analysis of an ATR engine for a reusable space launch vehicle and some of the practical problems that will be encountered in the development of this engine.

scholarly journals The effect of heat recovery on the optimal values of helicopter turboshaft engine parameters

2020 ◽  
Vol 19 (4) ◽  
pp. 43-57
Author(s):  
H. H. Omar ◽  
V. S. Kuz'michev ◽  
A. O. Zagrebelnyi ◽  
V. A. Grigoriev
Keyword(s):  
Heat Exchanger ◽  
Gas Turbine ◽  
Heat Recovery ◽  
Thermodynamic Cycle ◽  
Gas Turbine Engine ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Working Process ◽  
Turbine Engine ◽  
Recuperative Heat Exchanger

Recent studies related to fuel economy in air transport conducted in our country and abroad show that the use of recuperative heat exchangers in aviation gas turbine engines can significantly, by up to 20...30%, reduce fuel consumption. Until recently, the use of cycles with heat recovery in aircraft gas turbine engines was restrained by a significant increase in the mass of the power plant due to the installation of a heat exchanger. Currently, there is a technological opportunity to create compact, light, high-efficiency heat exchangers for use on aircraft without compromising their performance. An important target in the design of engines with heat recovery is to select the parameters of the working process that provide maximum efficiency of the aircraft system. The article focused on setting of the optimization problem and the choice of rational parameters of the thermodynamic cycle parameters of a gas turbine engine with a recuperative heat exchanger. On the basis of the developed method of multi-criteria optimization the optimization of thermodynamic cycle parameters of a helicopter gas turbine engine with a ANSAT recuperative heat exchanger was carried out by means of numerical simulations according to such criteria as the total weight of the engine and fuel required for the flight, the specific fuel consumption of the aircraft for a ton- kilometer of the payload. The results of the optimization are presented in the article. The calculation of engine efficiency indicators was carried out on the basis of modeling the flight cycle of the helicopter, taking into account its aerodynamic characteristics. The developed mathematical model for calculating the mass of a compact heat exchanger, designed to solve optimization problems at the stage of conceptual design of the engine and simulation of the transport helicopter flight cycle is presented. The developed methods and models are implemented in the ASTRA program. It is shown that optimal parameters of the working process of a gas turbine engine with a free turbine and a recuperative heat exchanger depend significantly on the heat exchanger effectiveness. The possibility of increasing the efficiency of the engine due to heat regeneration is also shown.

Sign in / Sign up

Export Citation Format

Share Document