Labyrinth Seal Leakage Tests: Tooth Profile, Tooth Thickness, and Eccentricity Effects

2007 ◽  
Author(s):  
Ahmed M. Gamal ◽  
John M. Vance
Keyword(s):  
Labyrinth Seal ◽  
Design Parameters ◽  
Working Fluid ◽  
Test Results ◽  
Blade Profile ◽  
Labyrinth Seals ◽  
Seal Design ◽  
Blade Thickness ◽  
Center Position ◽  
Blade Tip

The effects of two seal design parameters, namely blade (tooth) thickness and blade profile, on labyrinth seal leakage, as well as the effect of operating a seal in an off-center position, were examined through a series of non-rotating tests. Two reconfigurable seal designs were used, which enabled testing of two- four-, and six-bladed see-through labyrinth seals with different geometries using the same sets of seal blades. Leakage and cavity pressure measurements were made on each of twenty-three seal configurations with a four inch (101.6 mm) diameter journal. Tests were carried out with air as the working fluid at supply pressures of up to 100 psi-a (6.89 bar-a). Experimental results showed that doubling the thickness of the labyrinth blades significantly influenced leakage, reducing the flow-rate through the seals by up to 20%. Tests to determine the effect of blade-tip profile produced more equivocal results, with the results of experiments using each of the two test seal designs contradicting each other. Tests on one set of hardware indicated that beveling blades on the downstream side was most effective in limiting leakage whereas tests on newer hardware with tighter clearances indicated that seals with flat-tipped blades were superior. The test results illustrated that both blade profile and blade thickness could be manipulated so as to reduce seal leakage. However, an examination of the effects of both factors together indicated that the influence of one of these parameters can, to some extent, negate the influence of the other (especially in cases with tighter clearances). Lastly, for all configurations tested, results showed that leakage through a seal increases with increased eccentricity and that this phenomenon was considerably more pronounced at lower supply pressures.

Labyrinth Seal Leakage Tests: Tooth Profile, Tooth Thickness, and Eccentricity Effects

2008 ◽  
Vol 130 (1) ◽  
Author(s):  
Ahmed J. M. Gamal ◽  
John M. Vance
Keyword(s):  
Labyrinth Seal ◽  
Design Parameters ◽  
Working Fluid ◽  
Test Results ◽  
Blade Profile ◽  
Labyrinth Seals ◽  
Seal Design ◽  
Blade Thickness ◽  
Center Position ◽  
Blade Tip

The effects of two seal design parameters, namely blade (tooth) thickness and blade profile, on labyrinth seal leakage, as well as the effect of operating a seal in an off-center position, were examined through a series of nonrotating tests. Two reconfigurable seal designs were used, which enabled testing of two-, four-, and six-bladed see-through labyrinth seals with different geometries using the same sets of seal blades. Leakage and cavity pressure measurements were made on each of 23 seal configurations with a in.(101.6mm) diameter journal. Tests were carried out with air as the working fluid at supply pressures of up to 100psia (6.89bar). Experimental results showed that doubling the thickness of the labyrinth blades significantly influenced leakage, reducing the flow rate through the seals by up to 20%. Tests to determine the effect of blade-tip profile produced more equivocal results, with the results of experiments using each of the two test seal designs contradicting each other. Tests on one set of hardware indicated that beveling blades on the downstream side was most effective in limiting leakage, whereas tests on newer hardware with tighter clearances indicated that seals with flat-tipped blades were superior. The test results illustrated that both blade profile and blade thickness could be manipulated so as to reduce seal leakage. However, an examination of the effects of both factors together indicated that the influence of one of these parameters can, to some extent, negate the influence of the other (especially in cases with tighter clearances). finally, for all configurations tested, results showed that leakage through a seal increases with increased eccentricity and that this phenomenon was considerably more pronounced at lower supply pressures.

Labyrinth Seal Analysis

1972 ◽  
Vol 94 (1) ◽  
pp. 5-11
Author(s):  
H. A. Koenig ◽  
W. W. Bowley
Keyword(s):  
Gas Turbine ◽  
Theoretical Consideration ◽  
Computer Code ◽  
Labyrinth Seal ◽  
Design Parameters ◽  
Flow Conditions ◽  
Labyrinth Seals ◽  
Seal Design ◽  
Theoretical Considerations ◽  
Actual Test

A computer code is developed herein which is shown to be a useful tool in the design of labyrinth seals for gas turbine and other engineering applications. The algorithm is based upon theoretical considerations and is general enough to provide seal design parameters for a variety of input and flow conditions. Two examples are solved. The first, a theoretical consideration, demonstrates the ability of the program to effectively treat various geometrical and dynamic conditions. The second, an actual test, demonstrates the accuracy with which the analysis will predict the actual seal leakage behavior.

scholarly journals Test Results of a New Damper Seal for Vibration Reduction in Turbomachinery

1996 ◽  
Vol 118 (4) ◽  
pp. 843-846 ◽  
Author(s):  
J. M. Vance ◽  
J. Li
Keyword(s):  
Pressure Drop ◽  
Critical Speed ◽  
Vibration Reduction ◽  
Labyrinth Seal ◽  
Leakage Rate ◽  
Working Fluid ◽  
Test Results ◽  
Test Apparatus ◽  
Labyrinth Seals ◽  
New Type

A new type of labyrinth gas seal for damping vibration and whirl, called the TAMSEAL, has been evaluated in both nonrotating and rotating tests at Texas A&M University. Test results of the prototype, along with comparison tests of a conventional labyrinth seal, show up to 100 times more direct damping than the conventional bladed seal. The new design also has a feature that blocks swirl of the working fluid, which is known to be rotordynamically destabilizing in machines with conventional seals. Coastdown tests of the new seal were conducted at various pressures on a rotordynamic test apparatus with a critical speed at 4000 rpm and compared with identical testing of a conventional labyrinth seal. Rap tests of both seals were also conducted to measure the logarithmic decrement of free vibration, and the leakage of both seals was measured. Test results show large reductions in peak vibration at the critical speed in all cases, with the critical speed being completely eliminated by the TAMSEAL at some pressure drop conditions. The leakage rate of the tested TAMSEAL is higher than the conventional seal at the same clearance, but the large reductions in vibration and whirl amplitudes suggest that the TAMSEAL could be operated with smaller clearances than conventional labyrinth seals.

scholarly journals Test Results of a New Damper Seal for Vibration Reduction in Turbomachinery

1995 ◽  
Author(s):  
John M. Vance ◽  
Jiming Li
Keyword(s):  
Pressure Drop ◽  
Critical Speed ◽  
Vibration Reduction ◽  
Labyrinth Seal ◽  
Leakage Rate ◽  
Working Fluid ◽  
Test Results ◽  
Test Apparatus ◽  
Labyrinth Seals ◽  
New Type

A new type of labyrinth gas seal for damping vibration and whirl, called the TAMSEAL, has been evaluated in both non-rotating and rotating tests at Texas A&M University. Test results of the prototype, along with comparison tests of a conventional labyrinth seal, show up to one hundred times more direct damping than the conventional bladed seal. The new design also has a feature that blocks swirl of the working fluid, which is known to be rotordynamically destabilizing in machines with conventional seals. Coastdown tests of the new seal were conducted at various pressures on a rotordynamic test apparatus with a critical speed at 4000 rpm and compared with identical testing of a conventional labyrinth seal. Rap tests of both seals were also conducted to measure the logarithmic decrement of free vibration, and the leakage of both seals was measured. Test results show large reductions in peak vibration at the critical speed in all cases, with the critical speed being completely eliminated by the TAMSEAL at some pressure drop conditions. The leakage rate of the tested TAMSEAL is higher than the conventional seal at the same clearance, but the large reductions in vibration and whirl amplitudes suggest that the TAMSEAL could be operated with smaller clearances than conventional labyrinth seals.

Power Dissipation in Smooth and Honeycomb Labyrinth Seals

1989 ◽  
Author(s):  
W. F. McGreehan ◽  
S. H. Ko
Keyword(s):  
Power Dissipation ◽  
High Speed ◽  
Material Design ◽  
Labyrinth Seal ◽  
General Assumption ◽  
Design Parameters ◽  
Leakage Flow ◽  
Labyrinth Seals ◽  
Seal Design ◽  
Wide Range

The surface frictional characteristics of a labyrinth seal can result in significant windage power dissipation for high speed seals. Recent advances in seal design have produced high speed, high pressure labyrinth seals which operate at very low leakage rates. The reduced leakage is beneficial to gas turbine efficiency, but seal discharge temperatures can approach material design limits with high windage power dissipation. Also, a high air temperature rise can influence seal leakage flow. Consequently, the general assumption of negligible rotational effect on leakage is not always valid. A method is presented for the prediction of seal power dissipation and leakage flow over a wide range of design parameters. Results are compared to available test data and several approaches examined for the reduction of seal windage.

scholarly journals Rotordynamic Coefficient and Leakage Test Results for Interlock and Tooth-on-Stator Labyrinth Seals

1988 ◽  
Author(s):  
Dara W. Childs ◽  
David A. Elrod ◽  
Keith Hale
Keyword(s):  
Labyrinth Seal ◽  
Damping Coefficient ◽  
Test Results ◽  
Labyrinth Seals ◽  
Rotordynamic Coefficients ◽  
Damping Coefficients ◽  
Leakage Test ◽  
Stiffness And Damping ◽  
Rotordynamic Coefficient

Test results (leakage and rotordynamic coefficients) are presented for an interlock and tooth-on-stator labyrinth seals. Tests were carried out with air at speeds out to 16,000 cpm and supply pressures up to 7.5 bars. The rotordynamic coefficients consist of direct and cross-coupled stiffness and damping coefficients. Damping-coefficient data have not previously been presented for interlock seals. The test results support the following conclusions: (a) The interlock seal leaks substantially less than labyrinth seals. (b) Destabilizing forces are lower for the interlock seal. (c) The labyrinth seal has substantially greater direct damping values than the interlock seal. A complete rotordynamics analysis is needed to determine which type of seal would yield the best stability predictions for a given turbomachinery unit.

Development of a New Loss Model for Turbomachinery Labyrinth Seals

2021 ◽  
Author(s):  
Davendu Y. Kulkarni ◽  
Luca di Mare
Keyword(s):  
Flow Rate ◽  
Labyrinth Seal ◽  
Leakage Flow ◽  
Labyrinth Seals ◽  
Stream Tube ◽  
Flow Area ◽  
Loss Model ◽  
Seal Design ◽  
Wide Range ◽  
Numerical Experimentation

Abstract The preliminary design of labyrinth seals requires a fast and accurate estimate of the leakage flow. While the conventional bulk flow models can quickly predict labyrinth seal discharge characteristics, they lack the accuracy and pragmatism of modern CFD technique and vice-a-versa. This paper presents a new 1D loss model for straight-through gas labyrinth seals that can provide quick seal leakage flow predictions with CFD-equivalent accuracy. The present seal loss model is developed using numerical experimentation technique. Multiple CFD computations are conducted on straight-through labyrinth seal geometries for a range of pressure ratios. A distinct post-processing methodology is developed to extract the through-flow stream tube in seal. Total pressure losses and flow area variations experienced by the flow in seal stream-tube are systematically accounted for based on the well-known knife-to-knife (K2K) methodology. Regression analyses are conducted on the trends of variations of loss and area coefficients to derive the independent pressure loss and flow area correlations. These novel correlations can predict the bulk leakage flow rate, windage flow rate and inter-knife static pressures over a wide range of variation of flow and geometry parameters. Validation study shows that the leakage mass flow rate predicted by this model is accurate within ±8% of measured test data. This fast and accurate model can be employed for various applications such as, in seal design-analysis workflows, for secondary air system (SAS) performance analysis and for the rotor-dynamic and aeroelastic assessments of seals.

Application of Computational Fluid Dynamics Analysis for Rotating Machinery—Part II: Labyrinth Seal Analysis

2005 ◽  
Vol 127 (4) ◽  
pp. 820-826 ◽  
Author(s):  
Toshio Hirano ◽  
Zenglin Guo ◽  
R. Gordon Kirk
Keyword(s):  
Research Work ◽  
Flow Analysis ◽  
Labyrinth Seal ◽  
Bulk Flow ◽  
Working Fluid ◽  
Leakage Flow ◽  
Labyrinth Seals ◽  
Eccentric Rotor ◽  
Computational Fluid Dynamics Analysis ◽  
Force Components

Labyrinth seals are used in various kinds of turbo machines to reduce internal leakage flow. The working fluid, or the gas passing through the rotor shaft labyrinth seals, often generates driving force components that may increase the unstable vibration of the rotor. It is important to know the accurate rotordynamic force components for predicting the instability of the rotor-bearing-seal system. The major goals of this research were to calculate the rotordynamic force of a labyrinth seals utilizing a commercial CFD program and to further compare those results to an existing bulk flow computer program currently used by major US machinery manufacturers. The labyrinth seals of a steam turbine and a compressor eye seal are taken as objects of analysis. For each case, a 3D model with eccentric rotor was solved to obtain the rotordynamic force components. The leakage flow and rotor dynamics force predicted by CFX TASCFlow are compared with the results of the existing bulk flow analysis program DYNLAB. The results show that the bulk flow program gives a pessimistic prediction of the destabilizing forces for the conditions under investigation. Further research work will be required to fully understand the complex leakage flows in turbo machinery.

scholarly journals An Iwatsubo-Based Solution for Labyrinth Seals: Comparison to Experimental Results

1986 ◽  
Vol 108 (2) ◽  
pp. 325-331 ◽  
Author(s):  
D. W. Childs ◽  
J. K. Scharrer
Keyword(s):  
Pressure Distribution ◽  
Reaction Force ◽  
Labyrinth Seal ◽  
Momentum Equation ◽  
Test Results ◽  
Labyrinth Seals ◽  
Small Motion ◽  
First Order ◽  
Basic Equations ◽  
Separation Of Variable

The basic equations are derived for compressible flow in a labyrinth seal. The flow is assumed to be completely turbulent in the circumferential direction where the friction factor is determined by the Blasius relation. Linearized zeroth and first-order perturbation equations are developed for small motion about a centered position by an expansion in the eccentricity ratio. The zeroth-order pressure distribution is found by satisfying the leakage equation while the circumferential velocity distribution is determined by satisfying the momentum equation. The first-order equations are solved by a separation of variable solution. Integration of the resultant pressure distribution along and around the seal defines the reaction force developed by the seal and the corresponding dynamic coefficients. The results of this analysis are compared to published test results.

Hatch Seal Design Parameters for Manned Submersibles

2007 ◽  
Author(s):  
Jerry A. Henkener ◽  
Donald W. Johnson
Keyword(s):  
Large Diameter ◽  
Design Parameters ◽  
Test Results ◽  
Test Protocol ◽  
Design Data ◽  
Mechanical Joints ◽  
Southwest Research Institute ◽  
Seal Design ◽  
Face Seals ◽  
Manned Submersible

Southwest Research Institute conducted a test program on the 26-inch diameter hatch seal o-ring for a manned submersible vehicle. The tests measured o-ring extrusion at pressure differentials across the seal of up to 1560 psig and gaps between the sealing surfaces of up to 0.110 inches. This paper presents a test protocol for determining the maximum gap that a given size o-ring can seal at a given pressure. This paper also presents charts of extrusion vs. seal gap and addresses the potential for o-ring damage when the sealed joint is depressurized. The test results were used in the design of the hatch seal for the U.S. Navy Pressurized Rescue Module and represent the first industry-wide o-ring design data for face seals in large diameter mechanical joints that do not close with pressure.

Sign in / Sign up

Export Citation Format

Share Document