Optimizing a Suction Channel to Improve Performance of a Centrifugal Compressor Stage

2010 ◽  
Author(s):  
Manabu Yagi ◽  
Takanori Shibata ◽  
Hideo Nishida ◽  
Hiromi Kobayashi ◽  
Masanori Tanaka ◽  
...  
Keyword(s):  
Pressure Loss ◽  
Flow Coefficient ◽  
Design Parameters ◽  
Compressor Stage ◽  
Flow Distortion ◽  
Dominant Design ◽  
Improvement Effect ◽  
Computational Fluid Dynamics Cfd ◽  
Suction Flow ◽  
Stage Efficiency

Design parameters for a suction channel of process centrifugal compressors were investigated, and an optimizing method to improve efficiency by using the new design parameters was proposed. Both pressure loss and circumferential flow distortion in the suction channel were evaluated by using computational fluid dynamics (CFD). The main dimensions, which had a large influence on pressure loss and circumferential flow distortion, were identified by using design of experiments (DOE). Next, the passage sectional area ratios Ac/Ae, Ae/As, and Ac/As were found to be the dominant design parameters for the pressure loss and circumferential flow distortion, where Ac, Ae and As are passage sectional areas for the casing upstream side, casing entrance and impeller eye, respectively. Then the shape of the suction channel was optimized using Ac/Ae, Ae/As, and Ac/As. Finally, to evaluate the improvement effect of optimizing the values of Ac/Ae, Ae/As, and Ac/As on compressor stage performance, a base suction channel and an optimized type of suction channel were manufactured and tested. The design suction flow coefficient was 0.1 and the peripheral Mach number was 0.78. Test results showed that the optimized suction channel achieved 3.8% higher stage efficiency than the base one while maintaining the overall operating range from surge to choke. The method for optimizing suction channels by using the three described design parameters was concluded to be very effective for improving the stage efficiency.

Numerical Investigation of the Effect of Diffuser and Volute Design Parameters on the Performance of a Centrifugal Compressor Stage

2016 ◽  
Author(s):  
Lei Yu ◽  
William T. Cousins ◽  
Feng Shen ◽  
Georgi Kalitzin ◽  
Vishnu Sishtla ◽  
...  
Keyword(s):  
Centrifugal Compressor ◽  
Gas Flow ◽  
Pressure Rise ◽  
Design Parameters ◽  
Compressor Stage ◽  
Flow Distortion ◽  
Cross Sectional ◽  
Centrifugal Stage ◽  
And Performance ◽  
The Impact

In this effort, 3D CFD simulations are carried out for real gas flow in a refrigeration centrifugal compressor. Both commercial and the in-house CFD codes are used for steady and unsteady simulations, respectively. The impact on the compressor performance with various volute designs and diffuser modifications are investigated with steady simulations and the analysis is focused on both the diffuser and the volute loss, in addition to the flow distortion at impeller exit. The influence of the tongue, scroll diffusion ratio, diffuser length, and cross sectional area distribution is examined to determine the impact on size and performance. The comparisons of total pressure loss, static pressure recovery, through flow velocity, and the secondary flow patterns for different volute designs show that the performance of the centrifugal compressor depends upon how well the scroll portion of the volute collects the flow from the impeller and achieves the required pressure rise with minimum flow losses in the overall diffusion process. Finally, the best design is selected based on compressor stage pressure rise and peak efficiency improvement. An unsteady simulation of the full wheel compressor stage was carried out to further examine the interaction of impeller, diffuser and the volute. The unsteady flow interactions are shown to have a major impact on the performance of the centrifugal stage.

1D and 3D-Design Strategies for Pressure Slope Optimization of High-Flow Transonic Centrifugal Compressor Impellers

2018 ◽  
Author(s):  
A. Hildebrandt ◽  
T. Ceyrowsky
Keyword(s):  
Centrifugal Compressor ◽  
High Flow ◽  
Flow Coefficient ◽  
Design Parameters ◽  
Angle Distribution ◽  
Compressor Stage ◽  
Impeller Blade ◽  
Design Point ◽  
Centrifugal Compressor Stage ◽  
Transonic Centrifugal Compressor

The present paper deals with the numerical and theoretical investigations of the effect of geometrical dimensions and 1D-design parameters on the impeller pressure slope of a transonic centrifugal compressor stage for industrial process application. A database being generated during the multi-objective and multi-point design process of a high flow coefficient impeller, comprising 545 CFD (Computational Fluid Dynamics) designs is investigated in off-design and design conditions by means of RANS (Reynolds Averaged Navier Stokes) simulation of an impeller with vaneless diffuser. For high flow coefficients of 0.16 < phi < 0.18, the CFD-setup has been validated against measurement data regarding stage and impeller performance taken from MAN test rig experimental data for a centrifugal compressor stage of similar flow coefficient. The paper aims at answering the question how classical design parameter, such as the impeller blade angle distribution, impeller suction diameter and camber line length affect the local and total relative diffusion and pressure slope towards impeller stall operation. A second order analysis of the CFD database is performed by cross-correlating the CFD data with results from impeller two-zone 1D modelling and a rapid loading calculation process by Stanitz and Prian. The statistical covariance of first order 1D-analysis parameters such as the mixing loss of the impeller secondary flow, the slip factor, impeller flow incidence is analyzed, thereby showing strong correlation with the design and off-design point efficiency and pressure slope. Finally, guide lines are derived in order to achieve either optimized design point efficiency or maximum negative pressure slope characteristics towards impeller stall operation.

Effect of Leakage Flows on the Performance of a Family of Inline Centrifugal Compressors

2019 ◽  
Vol 141 (9) ◽  
Author(s):  
Hamid Hazby ◽  
Michael Casey ◽  
Luboš Březina
Keyword(s):  
Flow Coefficient ◽  
Leakage Flows ◽  
Geometrical Features ◽  
Work Input ◽  
Computational Fluid Dynamics Cfd ◽  
Compressor Work ◽  
The Impact ◽  
Compressor Efficiency ◽  
Stage Efficiency ◽  
Good Agreement

The impact of the hub and shroud leakage flows on the compressor efficiency has been investigated for four compressor stages with flow coefficients of 0.017, 0.0265, 0.063, and 0.118 belonging to a family of centrifugal compressor stages, designed for process compressor applications. A very good agreement was observed between the measured and predicted performance when the detailed geometrical features were included in the calculations. The computational fluid dynamics (CFD) calculations indicated that addition of leakage cavities and leakage flows resulted in about 3% drop in stage polytropic efficiency for the highest flow coefficient stage. The detrimental effect of leakages increased to about 8% for the lowest flow coefficient stage investigated here. The increase in the compressor work input due to the disc windage and the leakage recirculation was estimated from the CFD calculations and compared with values obtained using 1D methods, showing a very good agreement between the two. The impact of parasitic losses on compressor efficiency has been investigated and the contribution of various loss sources to the stage efficiency is discussed.

Performance Improvement of a Centrifugal Compressor Stage by Increasing Degree of Reaction and Optimizing Blade Loading of a 3D Impeller

2010 ◽  
Vol 133 (2) ◽  
Author(s):  
Takanori Shibata ◽  
Manabu Yagi ◽  
Hideo Nishida ◽  
Hiromi Kobayashi ◽  
Masanori Tanaka
Keyword(s):  
Performance Improvement ◽  
Relative Velocity ◽  
High Efficiency ◽  
Pressure Coefficient ◽  
Flow Coefficient ◽  
Compressor Stage ◽  
Blade Loading ◽  
Surge Margin ◽  
Velocity Diffusion ◽  
Stage Efficiency

Performance improvement of 3D impellers in a high specific speed range was investigated using computational fluid dynamics analyses and experimental tests. In order to reduce the loss production within the stator passages, the backsweep angle of the impellers was increased. At the same time, the inlet-to-exit relative velocity diffusion ratio was also increased by increasing the impeller exit width to prevent the reduction in the pressure ratio. Moreover, the blade loading distribution at the impeller shroud side was optimized to suppress the surge margin reduction caused by the increased relative velocity diffusion ratio. Five types of unshrouded impellers were designed, manufactured, and tested to evaluate the effects of blade loading, backsweep angle, and relative velocity diffusion ratio on the compressor performance. The design suction flow coefficient was 0.125 and the machine Mach number was 0.87. Test results showed that the compressor stage efficiency was increased by 5% compared with the base design without reducing the pressure coefficient and surge margin. It was concluded that an increased relative velocity diffusion ratio coupled with large backsweep angle was a very effective way to improve the compressor stage efficiency. An appropriate blade loading distribution was also important in order to achieve a wide operating range as well as high efficiency.

Affinity Law Modified to Predict the Pump Head Performance for Different Viscosities Using the Morrison Number

2018 ◽  
Vol 141 (2) ◽  
Author(s):  
Abhay Patil ◽  
Gerald Morrison
Keyword(s):  
Experimental Data ◽  
Reynolds Number ◽  
Flow Coefficient ◽  
Design Parameters ◽  
Sharp Change ◽  
Fluid Viscosity ◽  
Pump Head ◽  
Laminar And Turbulent Flow ◽  
Computational Fluid Dynamics Cfd ◽  
And Performance

The goal of this study is to provide pump users a simple means to predict a pump's performance change due to changing fluid viscosity. During the initial investigation, it has been demonstrated that pump performance can be represented in terms of the head coefficient, flow coefficient, and rotational Reynolds number with the head coefficient data for all viscosities falling on the same curve when presented as a function of ф*Rew−a. Further evaluation of the pump using computational fluid dynamics (CFD) simulations for wider range of viscosities demonstrated that the value of a (Morrison number) changes as the rotational Reynolds number increases. There is a sharp change in Morrison number in the range of 104<Rew<3*104 indicating a possible flow regime change between laminar and turbulent flow. The experimental data from previously published literature were utilized to determine the variation in the Morrison number as the function of rotational Reynolds number and specific speed. The Morrison number obtained from the CFD study was utilized to predict the head performance for the pump with known design parameters and performance from published literature. The results agree well with experimental data. The method presented in this paper can be used to establish a procedure to predict any pump's performance for different viscosities; however, more data are required to completely build the Morrison number plot.

One-Dimensional and Three-Dimensional Design Strategies for Pressure Slope Optimization of High-Flow Transonic Centrifugal Compressor Impellers

2019 ◽  
Vol 141 (5) ◽  
Author(s):  
A. Hildebrandt ◽  
T. Ceyrowsky
Keyword(s):  
Centrifugal Compressor ◽  
High Flow ◽  
Flow Coefficient ◽  
Design Parameters ◽  
Angle Distribution ◽  
Compressor Stage ◽  
Design Point ◽  
One Dimensional ◽  
Centrifugal Compressor Stage ◽  
Transonic Centrifugal Compressor

This paper deals with the numerical and theoretical investigations of the effect of geometrical dimensions and one-dimensional (1D)-design parameters on the impeller pressure slope of a transonic centrifugal compressor stage for industrial process application. A database being generated during the multi-objective and multipoint design process of a high flow coefficient impeller, comprising 545 computational fluid dynamics (CFD) designs is investigated in off-design and design conditions by means of Reynolds-averaged Navier–Stokes (RANS) simulation of an impeller with vaneless diffuser. For high flow coefficients of 0.16 < ϕdes < 0.18, the CFD-setup has been validated against measurement data regarding stage and impeller performance taken from MAN test rig experimental data for a centrifugal compressor stage of similar flow coefficient. This paper aims at answering the question how classical design parameter, such as the impeller blade angle distribution, impeller suction diameter, and camber line length affect the local and total relative diffusion and pressure slope toward impeller stall operation. A second-order analysis of the CFD database is performed by cross-correlating the CFD data with results from impeller two-zone 1D modeling and a rapid loading calculation process by Stanitz and Prian. The statistical covariance of first-order 1D-analysis parameters such as the mixing loss of the impeller secondary flow, the slip factor, impeller flow incidence is analyzed, thereby showing strong correlation with the design and off-design point efficiency and pressure slope. Finally, guide lines are derived in order to achieve either optimized design point efficiency or maximum negative pressure slope characteristics toward impeller stall operation.

Effect of the Stator Hub Configuration and Stage Design Parameters on Aerodynamic Loss in Axial Compressors

2014 ◽  
Author(s):  
Sungho Yoon ◽  
Rudolf Selmeier ◽  
Patricia Cargill ◽  
Peter Wood
Keyword(s):  
Pressure Loss ◽  
Axial Compressor ◽  
Flow Coefficient ◽  
Design Stage ◽  
Design Parameters ◽  
Leakage Flow ◽  
Design Decision ◽  
Leakage Loss ◽  
Stage Design ◽  
Degree Of Reaction

The choice of the stator hub configuration (i.e. cantilevered versus shrouded) is an important design decision in the preliminary design stage of an axial compressor. Therefore, it is important to understand the effect of the stator hub configuration on the aerodynamic performance. In particular, the stator hub configuration fundamentally affects the leakage flow across the stator. The effect of the stator hub configuration on the leakage flow and its consequent aerodynamic mixing loss with the main flow within the stator row is systematically investigated in this study. In the first part of the paper, a simple model is formulated to estimate the leakage loss across the stator hub as a function of fundamental stage design parameters, such as the flow coefficient, the degree of reaction and the work coefficient, in combination with some relevant geometric parameters including the clearance/span, the pitch-to-chord ratio and the number of seals for the shrouded geometry. The model is exercised in order to understand the effect of each of these design parameters on the leakage loss. It is found that, for a given flow coefficient and work coefficient, the leakage loss across the stator is substantially influenced by the degree of reaction. When a cantilevered stator is compared with a shrouded stator with a single seal at the same clearance, it is shown that a shrouded configuration is generally favored as a higher degree of reaction is selected, whereas a cantilevered configuration is desirable for a lower degree of reaction. Further to this, it is demonstrated that, for shrouded stators, an additional aerodynamic benefit can be achieved by using multiple seals. The second part of the paper investigates the effect of the rotating surfaces. Traditionally, only the pressure loss has been considered for stators. However, the current advanced CFD generally includes the leakage path with associated rotating surfaces, which impart energy to the flow. It is shown that the conventional loss coefficient, based on considering only the pressure loss, is misleading when hub leakage flows are modeled in detail, because there is energy addition due to the rotation of the hub or the shroud seals for the cantilevered stator and the shrouded stator, respectively. The calculation of the entropy generation across the stator is a better measure of relative performance when comparing two different stator hub configurations with detailed CFD.

Impact of Manufacturing Variability on the Aerodynamic Performance of a Centrifugal Compressor Stage With Curvilinear Blades

2016 ◽  
Author(s):  
A. Panizza ◽  
R. Valente ◽  
D. Rubino ◽  
L. Tapinassi
Keyword(s):  
Centrifugal Compressor ◽  
Sampling Methods ◽  
Aerodynamic Performance ◽  
High Flow ◽  
Flow Coefficient ◽  
Design Parameters ◽  
Compressor Stage ◽  
Centrifugal Compressor Stage ◽  
Performance Variability ◽  
The Impact

The goal of the present study is to quantify the uncertainty in the aerodynamic performance of a centrifugal compressor stage with curvilinear impeller blades, due to impeller manufacturing variability. Impellers with curvilinear element blades allow a greater control of secondary flows with respect to impellers having ruled blades. High flow coefficient impellers for centrifugal compressors exhibit larger secondary flow than medium or low flow coefficient impellers, due to the stronger curvature of the flow path and the larger blade height for the same external diameter. Thus curvilinear blade impellers allow to improve the efficiency and range of high flow coefficient centrifugal compressor stages. As the design of these impellers is more complex than the design of ruled blade impellers, it is important to estimate the impact of the impeller manufacturing variability on the performance of the full stage. Sampling methods are often used in uncertainty propagation studies. However, sampling based approaches require a very large number of samples to have an accurate estimate of the performance uncertainty. 3D steady RANS computations are necessary to capture the impact of the geometric variability of the curvilinear blade impeller, on the stage performance. Thus, sampling methods would require an excessive computational time. In this work, the Polynomial Chaos Expansion (PCE) method with arbitrary probability distributions, implemented in DAKOTA, is used to reduce the number of runs required for the uncertainty quantification study. Manufacturing measurement data are been used to derive the histograms of the main impeller design parameters. From these histograms, numerically-generated orthogonal polynomials are computed for each parameter using a discretized Stieltjes procedure. Stochastic expansion methods such as PCE suffer from the curse of dimensionality, i.e., an exponential increase in the number of runs as the number of uncertain parameters increases. To mitigate the curse of dimensionality, sparse grids are used, which allow a drastic reduction of the number of runs. The results of the study show that the performance variability is small, thus our design with curvilinear element blades is robust with respect to impeller manufacturing variability. Using Sobol indices, we also rank the design parameters according to their impact on the performance variability.

Design and Numerical Investigation of Advanced Radial Inlet for a Centrifugal Compressor Stage

2004 ◽  
Author(s):  
Yunbae Kim ◽  
Jay Koch
Keyword(s):  
Centrifugal Compressor ◽  
Pressure Loss ◽  
Total Pressure ◽  
Aerodynamic Performance ◽  
Total Pressure Loss ◽  
Compressor Stage ◽  
Flow Distortion ◽  
Centrifugal Compressor Stage ◽  
Initial Design ◽  
Wide Range

The performance of a centrifugal compressor stage can be seriously affected by inlet flow distortions due to an unsatisfactory inlet configuration and the resulting flow structure. In this study, two radial inlets were designed for a centrifugal compressor stage and investigated numerically using a commercially available 3D viscous Navier-Stokes code. The intent of the design was to minimize the total pressure loss across the inlet while distributing the flow as equally and uniformly as possible to the impeller inlet. For each inlet model, the aerodynamic performance was calculated from the simulation results and then the results from both models were evaluated and compared. The second radial inlet design outperformed the initial design in terms of total pressure loss, flow distortion and uniformity at the impeller inlet. Furthermore, the aerodynamic performance of the second radial inlet was insensitive to a wide range of mass flow rates compared to the initial design due to the distinctive geometric features implemented for the second inlet design.

Performance Improvement of a Centrifugal Compressor Stage by Increasing Degree of Reaction and Optimizing Blade Loading of a 3D-Impeller

2009 ◽  
Author(s):  
Takanori Shibata ◽  
Manabu Yagi ◽  
Hideo Nishida ◽  
Hiromi Kobayashi ◽  
Masanori Tanaka
Keyword(s):  
Performance Improvement ◽  
Relative Velocity ◽  
High Efficiency ◽  
Pressure Coefficient ◽  
Flow Coefficient ◽  
Compressor Stage ◽  
Blade Loading ◽  
Surge Margin ◽  
Velocity Diffusion ◽  
Stage Efficiency

Performance improvement of 3D impellers in a high specific speed range was investigated using computational fluid dynamics (CFD) analyses and experimental tests. In order to reduce the loss production within the stator passages, the backsweep angle of the impellers was increased. At the same time, the inlet-to-exit relative velocity diffusion ratio was also increased by increasing impeller exit width to prevent the reduction in pressure ratio. Moreover, the blade loading distribution at the impeller shroud side was optimized to suppress the surge margin reduction caused by the increased relative velocity diffusion ratio. Five types of unshrouded impellers were designed, manufactured and tested to evaluate the effects of blade loading, backsweep angle and relative velocity diffusion ratio on compressor performance. The design suction flow coefficient was 0.125 and the machine Mach number was 0.87. Test results showed that compressor stage efficiency was increased by 5% compared to the base design without reducing the pressure coefficient and surge margin. It was concluded that an increased relative velocity diffusion ratio coupled with large backsweep angle was a very effective way to improve compressor stage efficiency. An appropriate blade loading distribution was also important in order to achieve a wide operating range as well as high efficiency.

Sign in / Sign up

Export Citation Format

Share Document