Impact of Hub Clearance on Endwall Flow in a Highly Loaded Axial Compressor Stator

2013 ◽  
Author(s):  
Christian Beselt ◽  
Dieter Peitsch ◽  
Ruben van Rennings ◽  
Frank Thiele
Keyword(s):  
Secondary Flow ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Leading Edge ◽  
Flow Structures ◽  
Blade Loading ◽  
Numerical Predictions ◽  
Clearance Flow ◽  
Flow Features ◽  
Rotating Instability

Within the present paper the development and interaction of secondary flow structures at different hub clearance gaps at high blade loadings are investigated. Three-dimensional numerical computations were carried out at three levels of hub clearance, ranging from zero to 3% of blade chord. Experimental results at 1% and 3% chord hub clearance were obtained to asses the validity of the numerical predictions. The experimentally and numerically obtained results provide a detailed picture of the development, the interaction of secondary flow structures and the influence of clearance flow for high blade loading. Therefore the time averaged flow features obtained from the experimental test rig and from numerical simulations are compared. In addition this investigation tends to explain the phenomenon of rotating instability for this compressor stator at a specific operating point and different hub clearance gaps by analyzing the secondary flow structures in the leading edge region at the hub.

Interaction of Tip Clearance Flow and Three-Dimensional Separations in Axial Compressors

2006 ◽  
Author(s):  
Semiu A. Gbadebo ◽  
Nicholas A. Cumpsty ◽  
Tom P. Hynes
Keyword(s):  
Three Dimensional ◽  
Leading Edge ◽  
Horseshoe Vortex ◽  
Tip Clearance ◽  
Compressor Cascade ◽  
Suction Surface ◽  
Tip Clearance Flow ◽  
Separation Line ◽  
Numerical Predictions ◽  
Clearance Flow

This paper considers the interaction of tip clearance flow with three-dimensional (3D) separations in the corner region of a compressor cascade. Three-dimensional numerical computations were carried out using ten levels of tip clearance, ranging from zero to 2.18% of blade chord. The 3D separations on the blade suction surface were largely removed by the clearance flow for clearance about 0.58% of chord. For this cascade, experimental results at zero and 1.7% chord tip clearance were used to assess the validity of the numerical predictions. The removal mechanism was associated with the suppression of the leading edge horseshoe vortex and the interaction of tip clearance flow with the endwall boundary layer, which develops into a secondary flow as it is drifted towards the blade suction surface. Such interaction leads to the formation of a new 3D separation line on the endwall. The separation line forms the base of a separated stream surface which rolls up into the clearance vortex.

Interaction of Tip Clearance Flow and Three-Dimensional Separations in Axial Compressors

2006 ◽  
Vol 129 (4) ◽  
pp. 679-685 ◽  
Author(s):  
Semiu A. Gbadebo ◽  
Nicholas A. Cumpsty ◽  
Tom P. Hynes
Keyword(s):  
Three Dimensional ◽  
Leading Edge ◽  
Horseshoe Vortex ◽  
Tip Clearance ◽  
Compressor Cascade ◽  
Suction Surface ◽  
Tip Clearance Flow ◽  
Separation Line ◽  
Numerical Predictions ◽  
Clearance Flow

This paper considers the interaction of tip clearance flow with three-dimensional (3D) separations in the corner region of a compressor cascade. Three-dimensional numerical computations were carried out using ten levels of tip clearance, ranging from zero to 2.18% of blade chord. The 3D separations on the blade suction surface were largely removed by the clearance flow for clearance about 0.58% of chord. For this cascade, experimental results at zero and 1.7% chord tip clearance were used to assess the validity of the numerical predictions. The removal mechanism was associated with the suppression of the leading edge horseshoe vortex and the interaction of tip clearance flow with the endwall boundary layer, which develops into a secondary flow as it is driven towards the blade suction surface. Such interaction leads to the formation of a new 3D separation line on the endwall. The separation line forms the base of a separated stream surface which rolls up into the clearance vortex.

scholarly journals Reduction of Unsteady Blade Loading by Beneficial Use of Vortical and Potential Disturbances in an Axial Compressor With Rotor Clocking

1998 ◽  
Vol 120 (4) ◽  
pp. 705-713 ◽  
Author(s):  
S. T. Hsu ◽  
A. M. Wo
Keyword(s):  
Large Scale ◽  
Axial Compressor ◽  
Leading Edge ◽  
Forced Response ◽  
Suction Surface ◽  
Blade Loading ◽  
Beneficial Use ◽  
Unsteady Loading ◽  
Vortical Disturbance ◽  
First Time

This paper demonstrates reduction of stator unsteady loading due to forced response in a large-scale, low-speed, rotor/stator/rotor axial compressor rig by clocking the downstream rotor. Data from the rotor/stator configuration showed that the stator response due to the upstream vortical disturbance reaches a maximum when the wake impinges against the suction surface immediately downstream of the leading edge. Results from the stator/rotor configuration revealed that the stator response due to the downstream potential disturbance reaches a minimum with a slight time delay after the rotor sweeps pass the stator trailing edge. For the rotor/stator/rotor configuration, with Gap1 = 10 percent chord and Gap2 = 30 percent chord, results showed a 60 percent reduction in the stator force amplitude by clocking the downstream rotor so that the time occurrence of the maximum force due to the upstream vortical disturbance coincides with that of the minimum force due to the downstream potential disturbance. This is the first time, the authors believe, that beneficial use of flow unsteadiness is definitively demonstrated to reduce the blade unsteady loading.

A Study of Influences of Inlet Total Pressure Distortions On Clearance Flow in an Axial Compressor

2021 ◽  
Author(s):  
Guoming Zhu ◽  
Xiaolan Liu ◽  
Bo Yang ◽  
Moru Song
Keyword(s):  
Total Pressure ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Leading Edge ◽  
Stall Margin ◽  
Flow Cells ◽  
Static Pressure Distribution ◽  
Speed Flow ◽  
Clearance Flow ◽  
The Stability

Abstract The rotating distortion generated by upstream wakes or low speed flow cells is a kind of phenomenon in the inlet of middle and rear stages of an axial compressor. Highly complex inflow can obviously affect the performance and the stability of these stages, and is needed to be considered during compressor design. In this paper, a series of unsteady computational fluid dynamics (CFD) simulations is conducted based on a model of an 1-1/2 stage axial compressor to investigate the effects of the distorted inflows near the casing on the compressor performance and the clearance flow. Detailed analysis of the flow field has been performed and interesting results are concluded. The distortions, such as total pressure distortion in circumferential and radial directions, can block the tip region so that the separation loss and the mixing loss in this area are increased, and the efficiency and the total pressure ratio are dropped correspondingly. Besides, the distortions can change the static pressure distribution near the leading edge of the rotor, and make the clearance flow spill out of the rotor edge more easily under near stall condition, especially in the cases with co-rotating distortions. This phenomenon can be used to explain why the stall margin is deteriorated with nonuniform inflows.

Aero-Thermal Investigation of a Rib-Roughened Trailing Edge Channel With Crossing-Jets: Part I—Flow Field Analysis

2008 ◽  
Author(s):  
Alessandro Armellini ◽  
Filippo Coletti ◽  
Tony Arts ◽  
Christophe Scholtes
Keyword(s):  
Flow Field ◽  
Computational Study ◽  
Three Dimensional ◽  
Side Wall ◽  
Field Analysis ◽  
Trailing Edge ◽  
Present Contribution ◽  
Numerical Predictions ◽  
Flow Features ◽  
Rib Roughened

The present contribution addresses the aero-thermal experimental and computational study of a trapezoidal cross-section model simulating a trailing edge cooling cavity with one rib-roughened wall. The flow is fed through tilted slots on one side wall and exits through straight slots on the opposite side wall. The flow field aerodynamics is investigated in part I of the paper. The reference Reynolds number is defined at the entrance of the test section and set at 67500 for all the experiments. A qualitative flow model is deduced from surface-streamline flow visualizations. Two-dimensional Particle Image Velocimetry measurements are performed in several planes around mid-span of the channel and recombined to visualize and quantify three-dimensional flow features. The jets issued from the tilted slots are characterized and the jet-rib interaction is analyzed. Attention is drawn to the motion of the flow deflected by the rib-roughened wall and impinging on the opposite smooth wall. The experimental results are compared with the numerical predictions obtained from the finite volume, RANS solver CEDRE.

HP Vane Aerodynamics and Heat Transfer in the Presence of Aggressive Inlet Swirl

2012 ◽  
Vol 135 (2) ◽  
Author(s):  
Imran Qureshi ◽  
Andy D. Smith ◽  
Thomas Povey
Keyword(s):  
Heat Transfer ◽  
Cooling System ◽  
Three Dimensional ◽  
Leading Edge ◽  
Good Deal ◽  
Vortex Center ◽  
Research Facility ◽  
Lean Burn ◽  
Numerical Predictions ◽  
The Impact

Modern lean burn combustors now employ aggressive swirlers to enhance fuel-air mixing and improve flame stability. The flow at combustor exit can therefore have high residual swirl. A good deal of research concerning the flow within the combustor is available in open literature. The impact of swirl on the aerodynamic and heat transfer characteristics of an HP turbine stage is not well understood, however. A combustor swirl simulator has been designed and commissioned in the Oxford Turbine Research Facility (OTRF), previously located at QinetiQ, Farnborough UK. The swirl simulator is capable of generating an engine-representative combustor exit swirl pattern. At the turbine inlet plane, yaw and pitch angles of over ±40 deg have been simulated. The turbine research facility used for the study is an engine scale, short duration, rotating transonic turbine, in which the nondimensional parameters for aerodynamics and heat transfer are matched to engine conditions. The research turbine was the unshrouded MT1 design. By design, the center of the vortex from the swirl simulator can be clocked to any circumferential position with respect to HP vane, and the vortex-to-vane count ratio is 1:2. For the current investigation, the clocking position was such that the vortex center was aligned with the vane leading edge (every second vane). Both the aligned vane and the adjacent vane were characterized. This paper presents measurements of HP vane surface and end wall heat transfer for the two vane positions. The results are compared with measurements conducted without swirl. The vane surface pressure distributions are also presented. The experimental measurements are compared with full-stage three-dimensional unsteady numerical predictions obtained using the Rolls Royce in-house code Hydra. The aerodynamic and heat transfer characterization presented in this paper is the first of its kind, and it is hoped to give some insight into the significant changes in the vane flow and heat transfer that occur in the current generation of low NOx combustors. The findings not only have implications for the vane aerodynamic design, but also for the cooling system design.

scholarly journals The Inner Workings of Axial Casing Grooves in a One and a Half Stage Axial Compressor With a Large Rotor Tip Gap: Changes in Stall Margin and Efficiency

2018 ◽  
Author(s):  
Chunill Hah
Keyword(s):  
Boundary Layer ◽  
Axial Compressor ◽  
Leading Edge ◽  
Tip Clearance ◽  
Flow Rates ◽  
Stall Margin ◽  
Tip Clearance Flow ◽  
Flow Boundary ◽  
Clearance Flow ◽  
Large Rotor

Effects of axial casing grooves (ACGs) on the stall margin and efficiency of a one and a half stage low-speed axial compressor with a large rotor tip gap are investigated in detail. The primary focus of the current paper is to identify the flow mechanisms behind the changes in stall margin and on the efficiency of the compressor stage with a large rotor tip gap. Semicircular axial grooves installed in the rotor’s leading edge area are investigated. A large eddy simulation (LES) is applied to calculate the unsteady flow field in a compressor stage with ACGs. The calculated flow fields are first validated with previously reported flow visualizations and stereo PIV (SPIV) measurements. An in-depth examination of the calculated flow field indicates that the primary mechanism of the ACG is the prevention of full tip leakage vortex (TLV) formation when the rotor blade passes under the axial grooves periodically. The TLV is formed when the incoming main flow boundary layer collides with the tip clearance flow boundary layer coming from the opposite direction near the casing and rolls up around the rotor tip vortex. When the rotor passes directly under the axial groove, the tip clearance flow boundary layer on the casing moves into the ACGs and no roll-up of the incoming main flow boundary layer can occur. Consequently, the full TLV is not formed periodically as the rotor passes under the open casing of the axial grooves. Axial grooves prevent the formation of the full TLV. This periodic prevention of the full TLV generation is the main mechanism explaining how the ACGs extend the compressor stall margin by reducing the total blockage near the rotor tip area. Flows coming out from the front of the grooves affect the overall performance as it increases the flow incidence near the leading edge and the blade loading with the current ACGs. The primary flow mechanism of the ACGs is periodic prevention of the full TLV formation. Lower efficiency and reduced pressure rise at higher flow rates for the current casing groove configuration are due to additional mixing between the main passage flow and the flow from the grooves. At higher flow rates, blockage generation due to this additional mixing is larger than any removal of the flow blockage by the grooves. Furthermore, stronger double-leakage tip clearance flow is generated with this additional mixing with the ACGs at a higher flow rate than that of the smooth wall.

Effect of tip clearance size on the performance of a low-reaction transonic axial compressor rotor

2019 ◽  
Vol 234 (2) ◽  
pp. 127-142
Author(s):  
Wei Zhu ◽  
Songtao Wang ◽  
Longxin Zhang ◽  
Jun Ding ◽  
Zhongqi Wang
Keyword(s):  
Numerical Simulations ◽  
Dynamic Balance ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Stall Margin ◽  
Tip Clearance Flow ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Flow Phenomena

This study aimed to enhance the understanding of flow phenomena in low-reaction aspirated compressors. Three-dimensional, multi-passage steady and unsteady numerical simulations are performed to investigate the performance sensitivity to tip clearance variation on the first-stage rotor of a multistage low-reaction aspirated compressor. Three kinds of tip clearance sizes including 1.0τ, 2.0τ and 3.0τ are modeled, in which 1.0τ corresponds to the designed tip clearance size of 0.2 mm. The steady numerical simulations show that the overall performance of the rotor moves toward lower mass flow rate when the tip clearance size is increased. Moreover, energy losses, efficiency reduction and stall margin decrease are also observed with increasing tip clearance size. This can be mostly attributed to the damaging impact of intense tip clearance flow. For unsteady simulation, the result shows periodical oscillation of the tip leakage vortex and a “two-passage periodic structure” in the tip region at the near-stall point. The occurrence of the periodical oscillation is due to the severe interaction between the tip clearance flow and the shock wave. However, the rotor operating state is still stable at this working point because a dynamic balance is established between the tip clearance flow and incoming flow.

Investigation of Wedge Probe Wall Proximity Effects: Part 2—Numerical and Analytical Modeling

1997 ◽  
Vol 119 (3) ◽  
pp. 605-611 ◽  
Author(s):  
P. D. Smout ◽  
P. C. Ivey
Keyword(s):  
Large Scale ◽  
Three Dimensional ◽  
Outer Wall ◽  
Aerodynamic Characteristics ◽  
Proximity Effects ◽  
Wake Flow ◽  
Scale Model ◽  
Flow Structures ◽  
Flow Features ◽  
Wall Proximity

An experimental study of wedge probe wall proximity effects is described in Part 1 of this paper. Actual size and large-scale model probes were tested to understand the mechanisms responsible for this effect, by which free-stream pressure near the outer wall of a turbomachine may be overindicated by up to 20 percent dynamic head. CFD calculations of the flow over two-dimensional wedge shapes and a three-dimensional wedge probe were made in support of the experiments, and are reported in this paper. Key flow structures in the probe wake were identified that control the pressures indicated by the probe in a given environment. It is shown that probe aerodynamic characteristics will change if the wake flow structures are modified, for example by traversing close to the wall, or by calibrating the probe in an open jet rather than in a closed section wind tunnel. A simple analytical model of the probe local flows was derived from the CFD results. It is shown by comparison with experiment that this model captures the dominant flow features.

Investigation of Unsteady Flow Field in a Low-Speed One and a Half Stage Axial Compressor: Effects of Tip Gap Size on the Tip Clearance Flow Structure at Near Stall Operation

2014 ◽  
Author(s):  
Chunill Hah ◽  
Michael Hathaway ◽  
Joseph Katz
Keyword(s):  
Unsteady Flow ◽  
Flow Structure ◽  
Flow Instability ◽  
Axial Compressor ◽  
Leading Edge ◽  
Tip Clearance ◽  
Tip Clearance Flow ◽  
Low Speed ◽  
Clearance Flow ◽  
Tip Clearance Vortex

The primary focus of this paper is to investigate the effect of rotor tip gap size on how the rotor unsteady tip clearance flow structure changes in a low speed one and half stage axial compressor at near stall operation (for example, where maximum pressure rise is obtained). A Large Eddy Simulation (LES) is applied to calculate the unsteady flow field at this flow condition with both a small and a large tip gaps. The numerically obtained flow fields at the small clearance matches fairly well with the available initial measurements obtained at the Johns Hopkins University with 3-D unsteady PIV in an index-matched test facility which renders the compressor blades and casing optically transparent. With this setup, the unsteady velocity field in the entire flow domain, including the flow inside the tip gap, can be measured. The numerical results are also compared with previously published measurements in a low speed single stage compressor (Maerz et al. [2002]). The current study shows that, with the smaller rotor tip gap, the tip clearance vortex moves to the leading edge plane at near stall operating condition, creating a nearly circumferentially aligned vortex that persists around the entire rotor. On the other hand, with a large tip gap, the clearance vortex stays inside the blade passage at near stall operation. With the large tip gap, flow instability and related large pressure fluctuation at the leading edge are observed in this one and a half stage compressor. Detailed examination of the unsteady flow structure in this compressor stage reveals that the flow instability is due to shed vortices near the leading edge, and not due to a three-dimensional separation vortex originating from the suction side of the blade, which is commonly referred to during a spike-type stall inception. The entire tip clearance flow is highly unsteady. Many vortex structures in the tip clearance flow, including the sheet vortex system near the casing, interact with each other. The core tip clearance vortex, which is formed with the rotor tip gap flows near the leading edge, is also highly unsteady or intermittent due to pressure oscillations near the leading edge and varies from passage to passage. For the current compressor stage, the evidence does not seem to support that a classical vortex breakup occurs in any organized way, even with the large tip gap. Although wakes from the IGV influence the tip clearance flow in the rotor, the major characteristics of rotor tip clearance flows in isolated or single stage rotors are observed in this one and a half stage axial compressor.

Sign in / Sign up

Export Citation Format

Share Document