3D CFD Compressor Map Computation Process Accounting for Geometry Changes due to Off-Design Operation Loads

2014 ◽  
Author(s):  
Christian Janke ◽  
Kai Karger ◽  
Lilia Gaun ◽  
Dieter Bestle ◽  
André Huppertz
Keyword(s):  
Design Process ◽  
Total Pressure ◽  
Pressure Ratio ◽  
Operating Conditions ◽  
Aerodynamic Design ◽  
Quality Performance ◽  
Computation Process ◽  
Compressor Map ◽  
Aero Engines ◽  
Total Pressure Ratio

Compressor maps of aero engines show the relation between corrected inlet mass flow and total pressure ratio for various engine speeds. Different speed lines represent different operating conditions of the compressor, where especially operating bounds like surge and choke are important for the design process. Typically, 3D CFD compressor maps are computed with the so called hot geometry given for the aerodynamic design point. However, in reality airfoil shapes will change for different engine speeds and gas loads resulting in twisted airfoils and changed tip clearances. Thus, using the nominal hot geometry for the whole compressor map is not fully correct. In order to obtain higher quality performance maps these effects need to be considered. The paper shows a process for computing compressor maps with 3D CFD, where strucural deformations of the blade due to varying speeds and gas loads are taken into account by blade morphing. This process is applied to a 1.5-stage compressor showcase.

3D CFD Compressor Map Computation of a Multi-Stage Axial Compressor With Off-Design Adjusted Rotor Geometries

2016 ◽  
Author(s):  
Christian Janke ◽  
Markus Goller ◽  
Ivo Martin ◽  
Lilia Gaun ◽  
Dieter Bestle
Keyword(s):  
High Speed ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Design Point ◽  
Multi Stage ◽  
Compressor Design ◽  
Compressor Map ◽  
Aero Engines

Compressor maps of aero engines show the relation between corrected mass flow, corrected shaft speed, pressure ratio, and efficiency, where different operating conditions of the compressor are represented by different speed lines. These speed lines are an important information for the compressor design process, since they show important operation bounds like surge and choke. Typically, 3D CFD compressor maps are computed with the so called hot geometry given by the aerodynamic design point. But in reality aerofoil shapes change depending on engine speeds and gas loads resulting in twist of the blades and changes of tip clearance. In order to obtain a higher quality compressor map, all these effects must be taken into account. Therefore, a process is utilized which uses coupled CFD and FE analyses to account for load adjusted geometries aside the design point. For transformation of FE results into the CFD model a cold-to-hot blade morphing technique is used. The studies are performed for a 4.5 stage high speed axial compressor, where effects of varying tip clearance and geometry deformation are considered separately from each other. Finally, their combined effects are studied.

Design of High Specific Speed Mixed Flow Micro-Compressor for Co-Flow Jet Actuators

2019 ◽  
Author(s):  
Kewei Xu ◽  
Gecheng Zha
Keyword(s):  
Total Pressure ◽  
Static Pressure ◽  
Pressure Ratio ◽  
Flow Coefficient ◽  
High Mass ◽  
Aerodynamic Design ◽  
Mixed Flow ◽  
Work Distribution ◽  
Specific Speed ◽  
Total Pressure Ratio

Abstract This paper conducts aerodynamic design of a high specific speed mixed flow micro-compressor used as an actuator for Co-flow Jet (CFJ) Active Flow Control (AFC) airfoil. The aerodynamic design poses several challenges, including: 1) Small size with very low Reynolds number; 2) High specific speed for mixed-flow compressor due to high mass flow rate and low total pressure ratio; 3) Static pressure ratio lower than 1 to match the low pressure of CFJ airfoil leading edge (LE) suction peak. The numerical design approach is validated with a mixed flow micro-compressor with very good agreement between the predicted performance and the measured data. Front loaded rotor blade work distribution is adopted to decrease boundary layer loss at the blade surface. Free vortex work distribution is applied for the rotor span to reduce spanwise mixing loss. The rotor efficiency achieved by the numerical prediction is 91.7%. Significant loss is observed downstream of the rotor when the flow reaches the stator and the outlet guide vane (OGV). For the stator, it is found that an inlet and outlet flow path area ratio of 1.05 achieves a very high total pressure recovery of 99.29%. A very good stage isentropic efficiency of 84.3% is achieved. The final design of micro-compressor achieves a flow coefficient of 0.3 at the design point with a total pressure ratio of 1.117 and a static pressure ratio of 0.987. A structure FEM analysis indicates that the rotor blades satisfy the structure strength and modal frequency requirement.

Investigation Into the Effects of Hub Rotation on the Hub Leakage Flow of Cantilever Stator in a Transonic Axial Compressor

2020 ◽  
Author(s):  
Botao Zhang ◽  
Bo Liu ◽  
Xin Sun ◽  
Hang Zhao
Keyword(s):  
Total Pressure ◽  
Pressure Ratio ◽  
Leading Edge ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Compressor Cascade ◽  
Suction Surface ◽  
Blade Root ◽  
Flow Loss ◽  
Total Pressure Ratio

Abstract In order to explore the similarities and differences between the flow fields of cantilever stator and idealized compressor cascade with tip clearance, and to extend the cascade leakage model to compressors, the influence of stator hub rotation to represent cascade and cantilever stator on hub leakage flow was numerically studied. On this basis, the control strategy and mechanism of blade root suction were discussed. The results show that there is no obvious influence on stall margin of the compressor whether the stator hub is rotating or stationary. For rotating stator hub, the overall efficiency is decreased while the total pressure ratio is increased. At peak efficiency point and near stall point, the efficiency is reduced by about 0.43% and 0.34% individually, while the total pressure ratio is enlarged by about 0.23% and 0.27%, respectively. The gap leakage flow is promoted due to stator hub rotation, and the structure of the leakage vortex is weakened obviously. In addition, the hub leakage flow originating from the blade leading edge of rotating hub may contribute to double leakage near the trailing edge of the adjacent blade. However, the leakage flow directly out of the blade passage with stationary stator hub. The stator root loading and strength of the leakage flow increase with the rotation of the hub, and the leakage vortex is further away from the suction surface of the blade and is stretched to an ellipse closer to the endwall under the shear action. The rotating hub makes the flow loss near the stator gap increase, while the flow loss in the upper part of the blade root is decreased. Meanwhile, the total pressure ratio in the end area is increased. Blade root suction of cantilever stator can effectively control the hub leakage flow, inhibit the development of hub leakage vortex, and improve the flow capacity of the passage, thereby reducing the flow loss and modifying the flow field in the end zone.

Research on Optimization of the Design(Inverse) Issue of S2 Surface of Axial Compressor Based on Genetic Algorithm

2020 ◽  
Author(s):  
Zijing Chen ◽  
Bo Liu ◽  
Xiaoxiong Wu
Keyword(s):  
Genetic Algorithm ◽  
Total Pressure ◽  
Fitness Function ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Local Data ◽  
Real Coded Genetic Algorithm ◽  
Overall Efficiency ◽  
Total Pressure Ratio ◽  
Peak Value

Abstract In order to further improve the effectiveness of design(inverse) issue of S2 surface of axial compressor, a design method of optimization model based on real-coded genetic algorithm is instructed, with a detailed description of some important points such as the population setting, the fitness function design and the implementation of genetic operator. The method mainly takes the pressure ratio, the circulation as the optimization variables, the total pressure ratio and the overall efficiency of the compressor as the constraint condition and the decreasing of the diffusion factor of the compressor as the optimization target. In addition, for the propose of controlling the peak value of some local data after the optimization, a local optimization strategy is proposed to make the method achieve better results. In the optimization, the streamline curvature method is used to perform the iterative calculation of the aerodynamic parameters of the S2 flow surface, and the polynomial fitting method is used to optimize the dimensionality of the variables. The optimization result of a type of ten-stage axial compressor shows that the pressure ratio and circulation parameters have significant effect on the diffusion factor’s distribution, especially for the rotor pressure ratio. Through the optimization, the smoothness of the mass-average pressure ratio distribution curve of the rotors at all stages of the compressor is improved. The maximum diffusion factors in spanwise of rotor rows at the first, fifth and tenth stage of the compressor are reduced by 1.46%, 12.53% and 8.67%, respectively. Excluding the two calculation points at the root and tip of the blade because of the peak value, the average diffusion factors in spanwise are reduced by 1.28%, 3.46%, and 1.50%, respectively. For the two main constraints, the changes of the total pressure ratio and overall efficiency are less than 0.03% and 0.032%, respectively. In the end, a 3-d CFD numerical result is given to testify the effects of the optimization, which shows that the loss in the compressor is decreased by the optimization algorithm.

An Impact of Various Shroud Bleed Slot Configurations and Cavity Vanes on Compressor Map Width and the Inducer Flow Field

2013 ◽  
Vol 135 (4) ◽  
Author(s):  
Subenuka Sivagnanasundaram ◽  
Stephen Spence ◽  
Juliana Early ◽  
Bahram Nikpour
Keyword(s):  
Flow Field ◽  
Incidence Angle ◽  
Pressure Ratio ◽  
Leading Edge ◽  
Operating Conditions ◽  
Choked Flow ◽  
Recirculating Flow ◽  
Heavy Duty Diesel ◽  
Compressor Map ◽  
The Impact

This paper describes an investigation of map width enhancement and a detailed analysis of the inducer flow field due to various bleed slot configurations and vanes in the annular cavity of a turbocharger centrifugal compressor. The compressor under investigation is used in a turbocharger application for a heavy duty diesel engine of approximately 400 hp. This investigation has been undertaken using a computational fluid dynamics (CFD) model of the full compressor stage, which includes a manual multiblock-structured grid generation method. The influence of the bleed slot flow on the inducer flow field at a range of operating conditions has been analyzed, highlighting the improvement in surge and choked flow capability. The impact of the bleed slot geometry variations and the inclusion of cavity vanes on the inlet incidence angle have been studied in detail by considering the swirl component introduced at the leading edge by the recirculating flow through the slot. Further, the overall stage efficiency and the nonuniform flow field at the inducer inlet have been also analyzed. The analysis revealed that increasing the slot width has increased the map width by about 17%. However, it has a small impact on the efficiency, due to the frictional and mixing losses. Moreover, adding vanes in the cavity improved the pressure ratio and compressor performance noticeably. A detail analysis of the compressor with cavity vanes has also been presented.

Optimization of Highly Loaded Fan Rotor Based on Throughflow Model

2007 ◽  
Author(s):  
Hong Wu ◽  
Qiushi Li ◽  
Sheng Zhou
Keyword(s):  
Mass Flow ◽  
Total Pressure ◽  
Pressure Ratio ◽  
Optimization Method ◽  
Design Variables ◽  
Adaptive Simulated Annealing ◽  
Throughflow Model ◽  
Important Design ◽  
Total Pressure Ratio ◽  
Highly Loaded

This paper presents an optimization method for fan/compressor which couples throughflow model solving axisymmetric Euler equations with adaptive simulated annealing (ASA) algorithm. One of the advantages of this optimization method is that it spends much less time than 3D optimization due to the rapid solving of throughflow model. In addition, the optimization space is quite extensive because more design variables can be adjusted in throughflow phase, such as swirl distribution, hub curve and sweep. To validate this optimization method, a highly loaded fan rotor with pressure ratio of 3.06 as a baseline is optimized. During the optimization process, the objective function is total pressure ratio, moreover, mass flow and efficiency are selected as the constraint conditions. Three important design variables including swirl distribution, hub curve and sweep are parameterized using Bezier curve, and then optimized in throughflow model independently, finally the optimum designs are validated using 3D viscous CFD solver. It is shown that pressure ratio and rotor loading can be improved further through optimizing swirl distribution, however, hub and sweep curves take more effects on mass flow and efficiency respectively. The optimization results demonstrate the advantage and feasibility of this optimization method.

Numerical Investigation on the Effects of Circumferential Coverage of Injection in a Transonic Compressor With Discrete Tip Injection

2014 ◽  
Author(s):  
Wei Wang ◽  
Wuli Chu ◽  
Haoguang Zhang ◽  
Yanhui Wu
Keyword(s):  
Total Pressure ◽  
Pressure Ratio ◽  
Time Lag ◽  
Three Dimensional ◽  
Stability Margin ◽  
Transonic Compressor ◽  
Blade Tip ◽  
Tip Injection ◽  
The Stability ◽  
Total Pressure Ratio

Discrete tip injection upstream of the rotor tip is an effective technique to extend stability margin for a compressor system in an aeroengine. The current study investigates the effects of injectors’ circumferential coverage on compressor performance and stability using time-accurate three-dimensional numerical simulations for multi passages in a transonic compressor. The percentage of circumferential coverage for all the six injectors ranges from 6% to 87% for the five investigated configurations. Results indicate that circumferential coverage of tip injection can greatly affect compressor stability and total pressure ratio, but has little influence on adiabatic efficiency. The improvement of compressor total pressure ratio is linearly related with the increasing circumferential coverage. The unsteady flow fields show that there exists a non-ignorable time lag of the injection effects between the passage inlet and outlet, and blade tip loading will not decline until the injected flow reaches the passage outlet. Stability improves sharply with the increasing circumferential coverage when the coverage is less than 27%, but increases flatly for the rest. It is proven that the injection efficiency which is a measurement of averaged blockage decrement in the injected region is an effective guideline to predict the stability improvement.

The Optimization of a Centrifugal Impeller Based on a New Multi-Objective Evolutionary Strategy

2016 ◽  
Author(s):  
Xiaojian Li ◽  
Yijia Zhao ◽  
Zhengxian Liu ◽  
Hua Chen
Keyword(s):  
Pressure Ratio ◽  
Aerodynamic Performance ◽  
Evolutionary Strategy ◽  
Centrifugal Impeller ◽  
Nsga Ii ◽  
Multi Objective ◽  
Compressor Performance ◽  
Aero Engines ◽  
Total Pressure Ratio ◽  
Petrochemical Engineering

Centrifugal compressors with high aerodynamic performance are widely used in turbochargers, aero-engines and petrochemical engineering. The impeller is the core component and plays a key role in determining the compressor performance. This paper reports the optimisation of the aerodynamic performance of an industrial centrifugal impeller by a multi-objective evolutionary strategy. Firstly the 3-D modeling method for parameterisation of impeller’s geometry was described. Secondly the traditional NSGA-II method was modified to improve its ability and efficiency. Employed CFD code was first validated using the experimental data of an existing impeller. The optimisation was applied to the industrial centrifugal impeller through a two-step optimization process to allow for significant variations of the impeller geometry and speedy finding of the optimum. The optimisation was completed within 53 hours on a workstation with two 24-core processors (Xeon(R) E5-2670 v3 2.3GHz). The results indicated that the isentropic efficiency of the impeller increased by 5.3 percents and the total pressure ratio by 20.5 percents at design condition.

Experimental Investigation of Aspiration in a Multi-Stage High-Speed Axial-Compressor

2016 ◽  
Author(s):  
Jan Siemann ◽  
Ingolf Krenz ◽  
Joerg R. Seume
Keyword(s):  
Flow Field ◽  
Total Pressure ◽  
High Speed ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Reference Configuration ◽  
Corner Separation ◽  
Part Load ◽  
Total Pressure Ratio ◽  
Isentropic Efficiency

Reducing the fuel consumption is a main objective in the development of modern aircraft engines. Focusing on aircraft for mid-range flight distances, a significant potential to increase the engines overall efficiency at off-design conditions exists in reducing secondary flow losses of the compressor. For this purpose, Active Flow Control (AFC) by aspiration or injection of fluid at near wall regions is a promising approach. To experimentally investigate the aerodynamic benefits of AFC by aspiration, a 4½-stage high-speed axial-compressor at the Leibniz Universitaet Hannover was equipped with one AFC stator row. The numerical design of the AFC-stator showed significant hub corner separations in the first and second stator for the reference configuration at the 80% part-load speed-line near stall. Through the application of aspiration at the first stator, the numerical simulations predict the complete suppression of the corner separation not only in the first, but also in the second stator. This leads to a relative increase in overall isentropic efficiency of 1.47% and in overall total pressure ratio of 4.16% compared to the reference configuration. To put aspiration into practice, the high-speed axial-compressor was then equipped with a secondary air system and the AFC stator row in the first stage. All experiments with AFC were performed for a relative aspiration mass flow of less than 0.5% of the main flow. Besides the part-load speed-lines of 55% and 80%, the flow field downstream of each blade row was measured at the AFC design point. Experimental results are in good agreement with the numerical predictions. The use of AFC leads to an increase in operating range at the 55% part-load speed-line of at least 19%, whereas at the 80% part-load speed-line no extension of operating range occurs. Both speed-lines, however, do show a gain in total pressure ratio and isentropic efficiency for the AFC configuration compared to the reference configuration. Compared to the AFC design point, the isentropic efficiency ηis rises by 1.45%, whereas the total pressure ratio Πtot increases by 1.47%. The analysis of local flow field data shows that the hub corner separation in the first stator is reduced by aspiration, whereas in the second stator the hub corner separation slightly increases. The application of AFC in the first stage further changes the stage loading in all downstream stages. While the first and third stage become unloaded by application of AFC, the loading in terms of the De-Haller number increases in the second and especially in the fourth stage. Furthermore, in the reference as well as in the AFC configuration, the fourth stator performs significantly better than predicted by numerical results.

An Impact of Various Shroud Bleed Slot Configurations and Cavity Vanes on Compressor Map Width and the Inducer Flow Field

2011 ◽  
Author(s):  
Subenuka Sivagnanasundaram ◽  
Stephen Spence ◽  
Juliana Early ◽  
Bahram Nikpour
Keyword(s):  
Flow Field ◽  
Incidence Angle ◽  
Pressure Ratio ◽  
Leading Edge ◽  
Operating Conditions ◽  
Choked Flow ◽  
Recirculating Flow ◽  
Heavy Duty Diesel ◽  
Compressor Map ◽  
The Impact

This paper describes an investigation of map width enhancement and a detailed analysis of the inducer flow field due to various bleed slot configurations and vanes in the annular cavity of a turbocharger centrifugal compressor. The compressor under investigation is used in a turbocharger application for a heavy duty diesel engine of approximately 400hp. This investigation has been undertaken using a CFD model of the full compressor stage which includes a manual multi-block structured grid generation method. The influence of the bleed slot flow on the inducer flow field at a range of operating conditions has been analysed, highlighting the improvement in surge and choked flow capability. The impact of the bleed slot geometry variations and the inclusion of cavity vanes on the inlet incidence angle have been studied in detail by considering the swirl component introduced at the leading edge by the recirculating flow through the slot. Further, the overall stage efficiency and the non-uniform flow field at the inducer inlet have been also analysed. The analysis revealed that increasing the slot width has increased the map width by about 17%. However, it has a small impact on the efficiency due to the frictional and mixing losses. Moreover, adding vanes in the cavity improved the pressure ratio and compressor performance noticeably. A detail analysis of the compressor with cavity vanes has also been presented.

Sign in / Sign up

Export Citation Format

Share Document