An Impact of Various Shroud Bleed Slot Configurations and Cavity Vanes on Compressor Map Width and the Inducer Flow Field

2013 ◽  
Vol 135 (4) ◽  
Author(s):  
Subenuka Sivagnanasundaram ◽  
Stephen Spence ◽  
Juliana Early ◽  
Bahram Nikpour
Keyword(s):  
Flow Field ◽  
Incidence Angle ◽  
Pressure Ratio ◽  
Leading Edge ◽  
Operating Conditions ◽  
Choked Flow ◽  
Recirculating Flow ◽  
Heavy Duty Diesel ◽  
Compressor Map ◽  
The Impact

This paper describes an investigation of map width enhancement and a detailed analysis of the inducer flow field due to various bleed slot configurations and vanes in the annular cavity of a turbocharger centrifugal compressor. The compressor under investigation is used in a turbocharger application for a heavy duty diesel engine of approximately 400 hp. This investigation has been undertaken using a computational fluid dynamics (CFD) model of the full compressor stage, which includes a manual multiblock-structured grid generation method. The influence of the bleed slot flow on the inducer flow field at a range of operating conditions has been analyzed, highlighting the improvement in surge and choked flow capability. The impact of the bleed slot geometry variations and the inclusion of cavity vanes on the inlet incidence angle have been studied in detail by considering the swirl component introduced at the leading edge by the recirculating flow through the slot. Further, the overall stage efficiency and the nonuniform flow field at the inducer inlet have been also analyzed. The analysis revealed that increasing the slot width has increased the map width by about 17%. However, it has a small impact on the efficiency, due to the frictional and mixing losses. Moreover, adding vanes in the cavity improved the pressure ratio and compressor performance noticeably. A detail analysis of the compressor with cavity vanes has also been presented.

An Impact of Various Shroud Bleed Slot Configurations and Cavity Vanes on Compressor Map Width and the Inducer Flow Field

2011 ◽  
Author(s):  
Subenuka Sivagnanasundaram ◽  
Stephen Spence ◽  
Juliana Early ◽  
Bahram Nikpour
Keyword(s):  
Flow Field ◽  
Incidence Angle ◽  
Pressure Ratio ◽  
Leading Edge ◽  
Operating Conditions ◽  
Choked Flow ◽  
Recirculating Flow ◽  
Heavy Duty Diesel ◽  
Compressor Map ◽  
The Impact

This paper describes an investigation of map width enhancement and a detailed analysis of the inducer flow field due to various bleed slot configurations and vanes in the annular cavity of a turbocharger centrifugal compressor. The compressor under investigation is used in a turbocharger application for a heavy duty diesel engine of approximately 400hp. This investigation has been undertaken using a CFD model of the full compressor stage which includes a manual multi-block structured grid generation method. The influence of the bleed slot flow on the inducer flow field at a range of operating conditions has been analysed, highlighting the improvement in surge and choked flow capability. The impact of the bleed slot geometry variations and the inclusion of cavity vanes on the inlet incidence angle have been studied in detail by considering the swirl component introduced at the leading edge by the recirculating flow through the slot. Further, the overall stage efficiency and the non-uniform flow field at the inducer inlet have been also analysed. The analysis revealed that increasing the slot width has increased the map width by about 17%. However, it has a small impact on the efficiency due to the frictional and mixing losses. Moreover, adding vanes in the cavity improved the pressure ratio and compressor performance noticeably. A detail analysis of the compressor with cavity vanes has also been presented.

An Investigation of Compressor Map Width Enhancement and the Inducer Flow Field Using Various Configurations of Shroud Bleed Slot

2010 ◽  
Author(s):  
Subenuka Sivagnanasundaram ◽  
Stephen Spence ◽  
Juliana Early ◽  
Bahram Nikpour
Keyword(s):  
Flow Field ◽  
Incidence Angle ◽  
Leading Edge ◽  
Detailed Comparison ◽  
Operating Conditions ◽  
Tip Vortex ◽  
Performance Measurements ◽  
Impeller Blade ◽  
Choked Flow ◽  
The Impact

This paper describes an investigation of various shroud bleed slot configurations of a centrifugal compressor using CFD with a manual multi-block structured grid generation method. The compressor under investigation is used in a turbocharger application for a heavy duty diesel engine of approximately 400hp. The baseline numerical model has been developed and validated against experimental performance measurements. The influence of the bleed slot flow field on a range of operating conditions between surge and choke has been analysed in detail. The impact of the returning bleed flow on the incidence at the impeller blade leading edge due to its mixing with the main through-flow has also been studied. From the baseline geometry, a number of modifications to the bleed slot width have been proposed, and a detailed comparison of the flow characteristics performed. The impact of slot variations on the inlet incidence angle has been investigated, highlighting the improvement in surge and choked flow capability. Along with this, the influence of the bleed slot on stabilizing the blade passage flow by the suction of the tip and over-tip vortex flow by the slot has been considered near surge.

Map Width Enhancement Technique for a Turbocharger Compressor

2013 ◽  
Vol 136 (6) ◽  
Author(s):  
Subenuka Sivagnanasundaram ◽  
Stephen Spence ◽  
Juliana Early
Keyword(s):  
Performance Improvement ◽  
Peak Pressure ◽  
Pressure Ratio ◽  
Comparison Study ◽  
Heavy Duty ◽  
Recirculating Flow ◽  
Heavy Duty Diesel ◽  
And Performance ◽  
The Stability ◽  
The Impact

This paper presents an investigation of map width enhancement and the performance improvement of a turbocharger compressor using a series of static vanes in the annular cavity of a classical bleed slot system. The investigation has been carried out using both experimental and numerical analysis. The compressor stage used for this study is from a turbocharger unit used in heavy duty diesel engines of approximately 300 kW. Two types of vanes were designed and added to the annular cavity of the baseline classical bleed slot system. The purpose of the annular cavity vane technique is to remove some of the swirl that can be carried through the bleed slot system, which would influence the pressure ratio. In addition to this, the series of cavity vanes provides a better guidance to the slot recirculating flow before it mixes with the impeller main inlet flow. Better guidance of the flow improves the mixing at the inducer inlet in the circumferential direction. As a consequence, the stability of the compressor is improved at lower flow rates and a wider map can be achieved. The impact of two cavity vane designs on the map width and performance of the compressor was highlighted through a detailed analysis of the impeller flow field. The numerical and experimental study revealed that an effective vane design can improve the map width and pressure ratio characteristic without an efficiency penalty compared to the classical bleed slot system without vanes. The comparison study between the cavity vane and noncavity vane configurations presented in this paper showed that the map width was improved by 14.3% due to a significant reduction in surge flow and the peak pressure ratio was improved by 2.25% with the addition of a series of cavity vanes in the annular cavity of the bleed slot system.

Map Width Enhancement Technique for a Turbocharger Compressor

2012 ◽  
Author(s):  
Subenuka Sivagnanasundaram ◽  
Stephen Spence ◽  
Juliana Early
Keyword(s):  
Performance Improvement ◽  
Peak Pressure ◽  
Pressure Ratio ◽  
Comparison Study ◽  
Heavy Duty ◽  
Recirculating Flow ◽  
Heavy Duty Diesel ◽  
And Performance ◽  
The Stability ◽  
The Impact

This paper presents an investigation of map width enhancement and the performance improvement of a turbocharger compressor using a series of static vanes in the annular cavity of a classical bleed slot system. The investigation has been carried out using both experimental and numerical analysis. The compressor stage used for this study is from a turbocharger unit used in heavy duty diesel engines of approximately 300 kW. Two types of vanes have been designed and added to the annular cavity of the baseline classical bleed slot system. The purpose of the annular cavity vane technique is to remove some of the swirl that can be carried through the bleed slot system, which would influence the pressure ratio. In addition to this, the series of cavity vanes provides a better guidance to the slot recirculating flow before it mixes with the impeller main inlet flow. Better guidance of the flow improves the mixing at the inducer inlet in the circumferential direction. As a consequence, the stability of the compressor is improved at lower flow rates and a wider map can be achieved. The impact of two cavity vane designs on the map width and performance of the compressor has been highlighted through a detailed analysis of the impeller flow field. The numerical and experimental study revealed that an effective vane design can improve the map width and pressure ratio characteristic without an efficiency penalty compared to the classical bleed slot system without vanes. The comparison study between the cavity vane and non-cavity vane configurations presented in this paper showed that the map width was improved by 14.3% due to a significant reduction in surge flow and the peak pressure ratio was improved by 2.25% with the addition of a series of cavity vanes in the annular cavity of the bleed slot system.

Influence of Open and Closed Shroud Cavities on the Flowfield in a 2-Stage Turbine With Shrouded Blades

2003 ◽  
Author(s):  
Dieter E. Bohn ◽  
Ingo Balkowski ◽  
Hongwei Ma ◽  
Christian Tu¨mmers ◽  
Michael Sell
Keyword(s):  
Flow Field ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Leading Edge ◽  
Operating Conditions ◽  
Complex Flow ◽  
Multi Stage ◽  
Flow Through ◽  
Insight Into

An important goal of the development of turbine bladings is to increase the efficiency for an optimized use of energy resources. This necessitates the most possible insight into the complex flow phenomena in multi-stage turbine bladings. This paper presents a combined numerical and experimental investigation of the flow field in a 2-stage axial turbine with shrouded blades, where the axial gap between the shroud and the endwall is varied between 1mm (closed cavities) and 5 mm (opened cavities). In the experimental setup at the Institute of Steam and Gas Turbines, Aachen University, the turbine is operated at a low pressure ratio of 1.4 with an inlet pressure of 3.2 bar. The rotating speed is adjusted by a water brake, which is integrated into a swing frame running in hydrostatic bearings. The rotor power dissipates in the water brake, which enables a very accurate angular momentum determination. The mass flow is measured through a calibrated nozzle installed upstream of the turbine inlet at an accuracy of better than 1%, from which stage efficiencies can be derived. For both geometric configurations (open and closed shroud cavities), the flow field at both inlet and outlet is measured using 5-hole probes as well as temperature probes at three operating conditions. The test rig is especially designed to investigate the influence of the cavity size. Therefore, the radial gaps between shroud and casing is held near zero in order to prevent an axial flow through the cavities. The experimental results are used as boundary conditions for corresponding numerical multi-stage calculations of the 3D flow through the 2-stage turbine, using the highly accurate steady Navier-Stokes inhouse computer code, CHT-Flow. The flow field measurements and the numerical simulations give deeper insight into some of the cavity-related flow field phenomena. The measurement results as well as the simulations indicate that the stator leading edge has little influence on the inlet flow field. The flow through the shroud cavities has a significant influence on the field and therefore on the machine’s performance.

The Impact of Manufacturing Variations on Performance of a Transonic Axial Compressor Rotor

2020 ◽  
Vol 142 (8) ◽  
Author(s):  
Marcus Lejon ◽  
Niklas Andersson ◽  
Lars Ellbrant ◽  
Hans Mårtensson
Keyword(s):  
Flow Field ◽  
Geometric Mean ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Leading Edge ◽  
Mean Deviation ◽  
Design Intent ◽  
Compressor Rotor ◽  
The Mean ◽  
The Impact

Abstract In this paper, the impact of manufacturing variations on performance of an axial compressor rotor is evaluated at design rotational speed. The geometric variations from the design intent obtained from measurements were used to evaluate the impact of manufacturing variations on performance and the flow field in the rotor. The complete blisk is simulated using 3D computational fluid dynamics calculations, allowing for a detailed analysis of the impact of geometric variations on the flow. It is shown that the mean shift of the geometry from the design intent is responsible for the majority of the change in performance in terms of mass flow and total pressure ratio for this specific blisk. In terms of polytropic efficiency, the measured geometric scatter is shown to have a higher influence than the geometric mean deviation. The geometric scatter around the mean is shown to impact the pressure along the leading edge and the shock position. Furthermore, a blisk is analyzed with one blade deviating substantially from the design intent. It is shown that the impact of this blade on the flow is largely limited to the blade passages that it is directly a part of. It is also shown that the impact of this blade on the flow field can be represented by a simulation including three blade passages. In terms of loss, using five blade passages is shown to give a close estimate for the relative change in loss for the blade deviating substantially from the design intent and for the neighboring blades.

scholarly journals Influence of Blade Leading-Edge Shape on Rotating-Stalled Flow Characteristics in a Centrifugal Pump Impeller

2020 ◽  
Vol 10 (16) ◽  
pp. 5635
Author(s):  
Hongying Luo ◽  
Ran Tao ◽  
Jiandong Yang ◽  
Zhengwei Wang
Keyword(s):  
Flow Field ◽  
Centrifugal Pump ◽  
Incidence Angle ◽  
Flow Characteristics ◽  
Leading Edge ◽  
Rotating Stall ◽  
Pump Impeller ◽  
The Impact ◽  
Centrifugal Pump Impeller ◽  
Blade Leading Edge

Rotating stall, which is a common phenomenon in turbomachinery, strongly relates to the flow rate condition. In centrifugal impellers, rotating stall was induced by the incidence angle on blade leading-edge at partial-load. The blade leading-edge shape also influences the rotating stall because of the subtle change of local flow-field. In this study, the influence of blade leading-edge shape on rotating-stalled flow characteristics was studied in a six-blade centrifugal pump impeller. The stall pattern was “alternating”: Three passages were stalled, three passages were well-behaved, and the stalled and well-behaved passages occurred alternately. The stalled flow characteristics can be studied without the interruption of stall cell movement. Four types of blade leading-edge (blunt, sharp, ellipse, and round) were numerically compared based on the initial typical impeller and the numerical–experimental verification. The numerical comparison shows that the leading-edge shape has a strong influence on the stalled flow pattern, velocity, pressure, turbulence kinetic energy, and flow-induced noise inside impellers. The blunt and sharp leading-edge impellers had a similar internal pattern; the ellipse and round leading-edge impellers were also similar in the internal flow-field. Pressure pulsation analysis showed more obvious differences among these impellers. The main frequency and the pulsation peak–peak values were completely different because of the slight leading-edge shape differences. It revealed the impact of leading-edge geometry on the transient flow-field change under the same incidence angle conditions. It also provided reference for influencing or controlling the rotating stall by blade profile design.

scholarly journals A New Method to Determine the Impact of Individual Field Quantities on Cycle-to-Cycle Variations in a Spark-Ignited Gas Engine

Energies ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4136
Author(s):  
Clemens Gößnitzer ◽  
Shawn Givler
Keyword(s):  
Kinetic Energy ◽  
Flow Field ◽  
Turbulent Kinetic Energy ◽  
Negative Impact ◽  
Operating Conditions ◽  
Engine Operation ◽  
Gas Engine ◽  
Cycle Simulation ◽  
Simulation Results ◽  
The Impact

Cycle-to-cycle variations (CCV) in spark-ignited (SI) engines impose performance limitations and in the extreme limit can lead to very strong, potentially damaging cycles. Thus, CCV force sub-optimal engine operating conditions. A deeper understanding of CCV is key to enabling control strategies, improving engine design and reducing the negative impact of CCV on engine operation. This paper presents a new simulation strategy which allows investigation of the impact of individual physical quantities (e.g., flow field or turbulence quantities) on CCV separately. As a first step, multi-cycle unsteady Reynolds-averaged Navier–Stokes (uRANS) computational fluid dynamics (CFD) simulations of a spark-ignited natural gas engine are performed. For each cycle, simulation results just prior to each spark timing are taken. Next, simulation results from different cycles are combined: one quantity, e.g., the flow field, is extracted from a snapshot of one given cycle, and all other quantities are taken from a snapshot from a different cycle. Such a combination yields a new snapshot. With the combined snapshot, the simulation is continued until the end of combustion. The results obtained with combined snapshots show that the velocity field seems to have the highest impact on CCV. Turbulence intensity, quantified by the turbulent kinetic energy and turbulent kinetic energy dissipation rate, has a similar value for all snapshots. Thus, their impact on CCV is small compared to the flow field. This novel methodology is very flexible and allows investigation of the sources of CCV which have been difficult to investigate in the past.

Numerical Investigation of the Solidity Effect on Linear Compressor Cascades

2014 ◽  
Author(s):  
J. Sans ◽  
M. Resmini ◽  
J.-F. Brouckaert ◽  
S. Hiernaux
Keyword(s):  
Numerical Investigation ◽  
State Of The Art ◽  
Leading Edge ◽  
Operating Conditions ◽  
Compressor Cascade ◽  
Minimum Loss ◽  
Low Speed ◽  
High Mach ◽  
The Stability ◽  
The Impact

Solidity in compressors is defined as the ratio of the aerodynamic chord over the peripheral distance between two adjacent blades, the pitch. This parameter is simply the inverse of the pitch-to-chord ratio generally used in turbines. Solidity must be selected at the earliest design phase, i.e. at the level of the meridional design and represents a crucial step in the whole design process. Most of the existing studies on this topic rely on low-speed compressor cascade correlations from Carter or Lieblein. The aim of this work is to update those correlations for state-of-the-art controlled diffusion blades, and extend their application to high Mach number flow regimes more typical of modern compressors. Another objective is also to improve the physical understanding of the solidity effect on compressor performance and stability. A numerical investigation has been performed using the commercial software FINE/Turbo. Two different blade profiles were selected and investigated in the compressible flow regime as an extension to the low-speed data on which the correlations are based. The first cascade uses a standard double circular arc profile, extensively referenced in the literature, while the second configuration uses a state-of-the-art CDB, representative of low pressure compressor stator mid-span profile. Both profiles have been designed with the same inlet and outlet metal angles and the same maximum thickness but the camber and thickness distributions, the stagger angle and the leading edge geometry of the CDB have been optimized. The determination of minimum loss, optimum incidence and deviation is addressed and compared with existing correlations for both configurations and various Mach numbers that have been selected in order to match typical booster stall and choke operating conditions. The emphasis is set on the minimum loss performance at mid-span. The impact of the solidity on the operating range and the stability of the cascade are also studied.

Stall Behavior in an Ultra-High-Pressure-Ratio Centrifugal Compressor: Backward-Traveling Rotating Stall

2021 ◽  
pp. 1-51
Author(s):  
Yingjie Zhang ◽  
Xingen Lu ◽  
Yanfeng Zhang ◽  
Ziqing Zhang ◽  
Xu Dong ◽  
...  
Keyword(s):  
Boundary Layer ◽  
Shock Wave ◽  
Shock Intensity ◽  
Incidence Angle ◽  
Pressure Ratio ◽  
Leading Edge ◽  
Boundary Layer Separation ◽  
Rotating Stall ◽  
High Pressure Ratio ◽  
Ultra High Pressure

Abstract This paper describes the stall mechanism in an ultra-high-pressure-ratio centrifugal compressor. A model comprising all impeller and diffuser blade passages is used to conduct unsteady simulations that trace the onset of instability in the compressor. Backward-traveling rotating stall waves appear at the inlet of the radial diffuser when the compressor is throttled. Six stall cells propagate circumferentially at approximately 0.7% of the impeller rotation speed. The detached shock of the radial diffuser leading edge and the number of stall cells determine the direction of stall propagation, which is opposite to the impeller rotation direction. Dynamic mode decomposition is applied to instantaneous flow fields to extract the flow structure related to the stall mode. This shows that intensive pressure fluctuations concentrate in the diffuser throat as a result of changes in the detached shock intensity. The diffuser passage stall and stall recovery are accompanied by changes in incidence angle and shock wave intensity. When the diffuser passage stalls, the shock-induced boundary-layer separation region near the diffuser vane suction surface gradually expands, increasing the incidence angle and decreasing the shock intensity. The shock is pushed from the diffuser throat toward the diffuser leading edge. When the diffuser passage recovers from stall, the shock wave gradually returns to the diffuser throat, with the incidence angle decreasing and the shock intensity increasing. Once the shock intensity reaches its maximum, the diffuser passage suffers severe shock-induced boundary-layer separation and stalls again.

Sign in / Sign up

Export Citation Format

Share Document