Design and Test of a Transonic Axial Splittered Rotor

2015 ◽  
Author(s):  
Garth V. Hobson ◽  
Anthony J. Gannon ◽  
Scott Drayton
Keyword(s):  
Mass Flow ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Design Procedure ◽  
Tip Clearance ◽  
Turbine Engine ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Transonic Axial Compressor ◽  
Commercial Off The Shelf

A new design procedure was developed that uses commercial-off-the-shelf software (MATLAB, SolidWorks, and ANSYS-CFX) for the geometric rendering and analysis of a transonic axial compressor rotor with splitter blades. Predictive numerical simulations were conducted and experimental data were collected in a Transonic Compressor Rig. This study advanced the understanding of splitter blade geometry, placement, and performance benefits. In particular, it was determined that moving the splitter blade forward in the passage between the main blades, which was a departure from the trends demonstrated in the few available previous transonic axial compressor splitter blade studies, increased the mass flow range with no loss in overall performance. With a large 0.91 mm (0.036 in) tip clearance, to preserve the integrity of the rotor, the experimentally measured peak total-to-total pressure ratio was 1.69 and the peak total-to-total isentropic efficiency was 72 percent at 100 percent design speed. Additionally, a higher than predicted 7.5 percent mass flow rate range was experimentally measured, which would make for easier engine control if this concept were to be included in an actual gas turbine engine.

Experimental Investigation of Stepped Tip Gap Effects on the Performance of a Transonic Axial-Flow Compressor Rotor

1998 ◽  
Vol 120 (3) ◽  
pp. 477-486 ◽  
Author(s):  
D. W. Thompson ◽  
P. I. King ◽  
D. C. Rabe
Keyword(s):  
Mass Flow ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Axial Flow Compressor ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Percent Improvement ◽  
Flow Compressor

The effects of stepped-tip gaps and clearance levels on the performance of a transonic axial-flow compressor rotor were experimentally determined. A two-stage compressor with no inlet guide vanes was tested in a modern transonic compressor research facility. The first-stage rotor was unswept and was tested for an optimum tip clearance with variations in stepped gaps machined into the casing near the aft tip region of the rotor. Nine causing geometries were investigated consisting of three step profiles at each of three clearance levels. For small and intermediate clearances, stepped tip gaps were found to improve pressure ratio, efficiency, and flow range for most operating conditions. At 100 percent design rotor speed, stepped tip gaps produced a doubling of mass flow range with as much as a 2.0 percent increase in mass flow and a 1.5 percent improvement in efficiency. This study provides guidelines for engineers to improve compressor performance for an existing design by applying an optimum casing profile.

Experimental Investigation of Stepped Tip Gap Effects on the Performance of a Transonic Axial-Flow Compressor Rotor

1997 ◽  
Author(s):  
Donald W. Thompson ◽  
Paul I. King ◽  
Douglas C. Rabe
Keyword(s):  
Mass Flow ◽  
Pressure Ratio ◽  
Axial Flow ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Axial Flow Compressor ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Compressor Performance ◽  
Flow Compressor

The effects of stepped tip gaps and clearance levels on the performance of a transonic axial-flow compressor rotor were experimentally determined. A two-stage compressor with no inlet guide vanes was tested in a modern transonic compressor research facility. The first-stage rotor was unswept and was tested for an optimum tip clearance with variations in stepped gaps machined into the casing near the aft tip region of the rotor. Nine casing geometries were investigated consisting of three step profiles at each of three clearance levels. For small and intermediate clearances, stepped tip gaps were found to improve pressure ratio, efficiency, and flow range for most operating conditions. At 100% design rotor speed, stepped tip gaps produced a doubling of mass flow range with as much as a 2.0% increase in mass flow and a 1.5% improvement in efficiency. This study provides guidelines for engineers to improve compressor performance for an existing design by applying an optimum casing profile.

CFD Code Validation and Qualitative Study of Effects of Tip Clearance Variation on Performance of Transonic Axial Compressor Rotor

2012 ◽  
Author(s):  
Aniket R. Patkar ◽  
Srinivethan Rangasamy ◽  
Sreekanth Raghunath ◽  
Vilas Kalamkar
Keyword(s):  
Pressure Ratio ◽  
Splitting Method ◽  
Flow Characteristics ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Maximum Pressure ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Transonic Axial Compressor ◽  
Multiple Frame

The main objective of this work is the validation of Computational Fluid Dynamics (CFD) code used for analysis of transonic axial compressors. NASA Rotor 35 is used here as test case for validation. In this work, computations are performed using parallelized RANS code, to predict the transonic axial compressor rotor flow characteristics. Advection Upstream Splitting Method (AUSM) scheme has been used. A Multiple Frame of Reference approach has been used to model the rotor passage. Spalart-Allmaras turbulence model is used to model turbulence. Multiblock Structured mesh is used. Performance characteristics for the entire range of operation, from maximum mass flow rate till maximum pressure ratio, have been simulated. The results obtained are comparable with experimental data within 5–10% error. Investigations have been carried out to study the effect of varying tip clearance in NASA Rotor 35. The present work is intended to study the clearance flow trajectory as a function of varying tip clearance. The effects of shock/vortex interaction in tip clearance region are also studied. The effects of tip clearance size on the generation and evolution of the end-wall vortical structures are discussed by investigating their evolutionary trajectories. By this study, it is observed that as tip clearance reduces, clearance flow trajectory moves downstream. From this it can be concluded that if tip clearance increases, tip clearance vortices expand. This may help in casing-treatment or tip-treatment to mitigate the loss in the performance, if the tip clearance increases.

scholarly journals Blockage Development in a Transonic, Axial Compressor Rotor

1997 ◽  
Author(s):  
Kenneth L. Suder
Keyword(s):  
Boundary Layer ◽  
Axial Compressor ◽  
Flow Region ◽  
Tip Clearance ◽  
Surface Boundary ◽  
Core Flow ◽  
The Core ◽  
Compressor Rotor ◽  
Transonic Axial Compressor ◽  
The Impact

A detailed experimental investigation to understand and quantify the development of blockage in the flow field of a transonic, axial flow compressor rotor (NASA Rotor 37) has been undertaken. Detailed laser anemometer measurements were acquired upstream, within, and downstream of a transonic, axial compressor rotor operating at 100%, 85%, 80%, and 60% of design speed which provided inlet relative Mach numbers at the blade tip of 1.48, 1.26, 1.18, and 0.89 respectively. The impact of the shock on the blockage development, pertaining to both the shock / boundary layer interactions and the shock / tip clearance flow interactions, is discussed. The results indicate that for this rotor the blockage in the endwall region is 2–3 times that of the core flow region, and the blockage in the core flow region more than doubles when the shock strength is sufficient to separate the suction surface boundary layer.

Numerical Investigation of Relation Between Unsteady Behavior of Tip Leakage Vortex and Rotating Disturbance in a Transonic Axial Compressor Rotor

2008 ◽  
Author(s):  
K. Yamada ◽  
K. Funazaki ◽  
H. Sasaki
Keyword(s):  
Vortex Breakdown ◽  
Axial Compressor ◽  
Tip Clearance ◽  
Tip Leakage Vortex ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Transonic Axial Compressor ◽  
Rotating Instability

The purpose of this study is to have a better understanding of the unsteady behavior of tip clearance flow at near-stall condition from a multi-passage simulation and to clarify the relation between such unsteadiness and rotating disturbance. This study is motivated by the following concern. A single passage simulation has revealed the occurrence of the tip leakage vortex breakdown at near-stall condition in a transonic axial compressor rotor, leading to the unsteadiness of the tip clearance flow field in the rotor passage. These unsteady flow phenomena were similar to those in the rotating instability, which is classified in one of the rotating disturbances. In other words it is possible that the tip leakage vortex breakdown produces a rotating disturbance such as the rotating instability. Three-dimensional unsteady RANS calculation was conducted to simulate the rotating disturbance in a transonic axial compressor rotor (NASA Rotor 37). The four-passage simulation was performed so as to capture a short length scale disturbance like the rotating instability and the spike-type stall inception. The simulation demonstrated that the unsteadiness of tip leakage vortex, which was derived from the vortex breakdown at near-stall condition, invoked the rotating disturbance in the rotor, which is similar to the rotating instability.

Investigation of Tip Clearance Modeling Techniques for a Transonic Compressor Rotor

2009 ◽  
Author(s):  
Sean T. Barrows ◽  
Ravishankar Balasubramian ◽  
Jen-Ping Chen
Keyword(s):  
Pressure Ratio ◽  
Tip Clearance ◽  
Tip Vortex ◽  
Vena Contracta ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Radial Depth ◽  
Modeling Techniques ◽  
Final Approach ◽  
Viable Approach

Computational fluid dynamics (CFD) codes are becoming an integral part of the design and analysis process involved with creating and improving upon new engine designs. This necessitates the investigation and development of accurate modeling techniques for flow simulations with a quick turn around time of typically 48 hours. The present paper is focused on increasing the fidelity of compressor rotor simulations by examining three rotor tip clearance modeling techniques. The first approach models the tip clearance region as a loss-less, periodic, un-gridded region as first proposed by Kirtley et al. The second approach is a modification of this technique to study the vena-contracta effects. The tip clearance region remains un-gridded, but, the physical radial depth of tip clearance is gradually reduced to the smallest constriction typically seen in the tip clearance because of flow phenomena such as the shroud and blade-tip boundary layers. The final approach is a completely gridded tip clearance region of full depth to verify the vena-contracta approach as well as to determine if any increase in fidelity is achieved through this computationally costly procedure. These three tip clearance modeling approaches are applied to the NASA transonic compressor rotor, Rotor-35, in a rotor only configuration and the predicted operational ranges are compared to available LDV data. Span-wise performance characteristics such as total pressure ratio and total temperature ratio are compared at a near peak efficiency and at a near-stall operating point. Tip-vortex resolution and predictions are also examined. The merits and demerits of the three approaches are discussed and recommendations are made for a viable approach in terms of accuracy and computational resources.

Effects of Number of Circumferential Casing Grooves on Stall Flow Characteristics of a Transonic Axial Compressor

2013 ◽  
Vol 284-287 ◽  
pp. 727-732
Author(s):  
Jin Hyuk Kim ◽  
Kwang Yong Kim ◽  
Kyung Hun Cha
Keyword(s):  
Mass Flow ◽  
Stokes Equations ◽  
Pressure Ratio ◽  
Flow Analysis ◽  
Flow Characteristics ◽  
Axial Compressor ◽  
Flow Region ◽  
High Mass ◽  
Convergence Criteria ◽  
Transonic Axial Compressor

This work investigates the effects of circumferential casing grooves on stall flow characteristics of a transonic axial compressor. Numerical analysis is conducted by solving three-dimensional steady Reynolds-averaged Navier-Stokes equations with the shear stress transport turbulence model. The results of flow analysis for an axial compressor with smooth casing are validated in comparison with experimental data for the pressure ratio and adiabatic efficiency. The numerical stall inception point is identified from the last converged point by convergence criteria, and the stall margin is predicted numerically. The peak adiabatic efficiency point is also obtained by reducing the normalized mass flow in the high mass flow region. In order to explore the influence of number of the circumferential casing grooves on the performance of the compressor, the stall margins and peak adiabatic efficiencies are evaluated compared to the case smooth casing. The stability of the axial compressor with circumferential casing grooves is found to be sensitively influenced by the number of grooves.

scholarly journals Experimental and Computational Investigation of the Tip Clearance Flow in a Transonic Axial Compressor Rotor

1996 ◽  
Vol 118 (2) ◽  
pp. 218-229 ◽  
Author(s):  
K. L. Suder ◽  
M. L. Celestina
Keyword(s):  
Axial Compressor ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Vortex Interaction ◽  
Peak Efficiency ◽  
Tip Clearance Flow ◽  
Compressor Rotor ◽  
Clearance Flow ◽  
Transonic Axial Compressor ◽  
Design Speed

Experimental and computational techniques are used to investigate tip clearance flows in a transonic axial compressor rotor at design and part-speed conditions. Laser anemometer data acquired in the endwall region are presented for operating conditions near peak efficiency and near stall at 100 percent design speed and at near peak efficiency at 60 percent design speed. The role of the passage shock/leakage vortex interaction in generating endwall blockage is discussed. As a result of the shock/vortex interaction at design speed, the radial influence of the tip clearance flow extends to 20 times the physical tip clearance height. At part speed, in the absence of the shock, the radial extent is only five times the tip clearance height. Both measurements and analysis indicate that under part-speed operating conditions a second vortex, which does not originate from the tip leakage flow, forms in the end-wall region within the blade passage and exits the passage near midpitch. Mixing of the leakage vortex with the primary flow downstream of the rotor at both design and part-speed conditions is also discussed.

A Comparison between Measured and Computed Flow Fields in a Transonic Compressor Rotor

1980 ◽  
Vol 102 (4) ◽  
pp. 883-889 ◽  
Author(s):  
P. W. McDonald ◽  
C. R. Bolt ◽  
R. J. Dunker ◽  
H. B. Weyer
Keyword(s):  
Mach Number ◽  
Total Pressure ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Computational Procedure ◽  
Operating Conditions ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Pressure Profiles

The flow field within the rotor of a transonic axial compressor has been computed and compared to measurements obtained with an advanced laser velocimeter. The compressor was designed for a total pressure ratio of 1.51 at a relative tip Mach number of 1.4. The comparisons are made at 100 percent design speed (20,260 RPM) with pressure ratios corresponding to peak efficiency, near surge, and wide open discharge operating conditions. The computational procedure iterates between a blade-to-blade calculation and an intrablade through flow calculation. Calculated Mach number contours, surface pressure distributions, and exit total pressure profiles are in agreement with the experimental data demonstrating the usefulness of quasi three-dimensional calculations in compressor design.

Effect of Trailing Edge Crenulation on the Performance and Stall Margin of a Transonic Axial Compressor

2013 ◽  
Author(s):  
S. Subbaramu ◽  
Quamber H. Nagpurwala ◽  
A. T. Sriram
Keyword(s):  
Beneficial Effect ◽  
Total Pressure ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Compressor Cascade ◽  
Trailing Edge ◽  
Stall Margin ◽  
Positive Effects ◽  
Compressor Rotor ◽  
Transonic Axial Compressor

This paper deals with the numerical investigations on the effect of trailing edge crenulation on the performance of a transonic axial compressor rotor. Crenulation is broadly considered as a series of small notches or slots at the edge of a thin object, like a plate. Incorporating such notches at the trailing edge of a compressor cascade has shown beneficial effect in terms of reduction in total pressure loss due to enhanced mixing in the wake region. These notches act as vortex generators to produce counter rotating vortices, which increase intermixing between the free stream flow and the low momentum wake fluid. Considering the positive effects of crenulation in a cascade, it was hypothesized that the same technique would work in a rotating compressor to enhance its performance and stall margin. However, the present CFD simulations on a transonic compressor rotor have given mixed results. Whereas the peak total pressure ratio in the presence of trailing edge crenulation reduced, the stall margin improved by 2.97% compared to the rotor with straight edge blades. The vortex generation at the crenulated trailing edge was not as strong as reported in case of linear compressor cascade, but it was able to influence the flow field in the rotor tip region so as to energize the low momentum end-wall flow in the aft part of the blade passage. This beneficial effect delayed flow separation and allowed the mass flow rate to be reduced to still lower levels resulting in improved stall margin. The reduction in pressure ratio with crenulation was surprising and might be due to increased mixing losses downstream of the blade.

Sign in / Sign up

Export Citation Format

Share Document