Effect of Trailing Edge Crenulation on the Performance and Stall Margin of a Transonic Axial Compressor

2013 ◽  
Author(s):  
S. Subbaramu ◽  
Quamber H. Nagpurwala ◽  
A. T. Sriram
Keyword(s):  
Beneficial Effect ◽  
Total Pressure ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Compressor Cascade ◽  
Trailing Edge ◽  
Stall Margin ◽  
Positive Effects ◽  
Compressor Rotor ◽  
Transonic Axial Compressor

This paper deals with the numerical investigations on the effect of trailing edge crenulation on the performance of a transonic axial compressor rotor. Crenulation is broadly considered as a series of small notches or slots at the edge of a thin object, like a plate. Incorporating such notches at the trailing edge of a compressor cascade has shown beneficial effect in terms of reduction in total pressure loss due to enhanced mixing in the wake region. These notches act as vortex generators to produce counter rotating vortices, which increase intermixing between the free stream flow and the low momentum wake fluid. Considering the positive effects of crenulation in a cascade, it was hypothesized that the same technique would work in a rotating compressor to enhance its performance and stall margin. However, the present CFD simulations on a transonic compressor rotor have given mixed results. Whereas the peak total pressure ratio in the presence of trailing edge crenulation reduced, the stall margin improved by 2.97% compared to the rotor with straight edge blades. The vortex generation at the crenulated trailing edge was not as strong as reported in case of linear compressor cascade, but it was able to influence the flow field in the rotor tip region so as to energize the low momentum end-wall flow in the aft part of the blade passage. This beneficial effect delayed flow separation and allowed the mass flow rate to be reduced to still lower levels resulting in improved stall margin. The reduction in pressure ratio with crenulation was surprising and might be due to increased mixing losses downstream of the blade.

Numerical Studies on the Effect of Gurney Flap on Aerodynamic Performance and Stall Margin of a Transonic Axial Compressor Rotor

2014 ◽  
Author(s):  
Mudassir Ahmed M. Rafeeq ◽  
Quamber H. Nagpurwala ◽  
Subbaramu Shivaramaiah
Keyword(s):  
Total Pressure ◽  
Rotor Blade ◽  
Peak Pressure ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Stall Margin ◽  
Compressor Rotor ◽  
Numerical Studies ◽  
Gurney Flap ◽  
Total Pressure Ratio

Numerical studies have been carried out on the effectiveness of trailing edge Gurney flap on a transonic axial compressor rotor. The baseline geometry of the rotor blade was modified at the trailing edge by introducing Gurney flaps of varying depth and span-wise length, viz. 1 mm, 2 mm and 3 mm depth with 20% span length of Gurney flap from tip (designated as GF1-20, GF2-20 and GF3-20 respectively), and 1 mm depth with 50% and 100% span length (designated as GF1-50 and GF1-100 respectively). Geometric models of the compressor rotor without and with Gurney flaps were generated using CATIA V5 software and CFD simulations at 100% design rotor speed were carried out using ANSYS CFX software. Results have shown that the compressor total pressure ratio increased with increase in both depth and spanwise length of Gurney flap. Peak pressure ratio increased from 1.51 for baseline case to 1.58 for rotor GF1-100. However, the peak isentropic efficiency remained almost constant for various Gurney flap configurations, except for GF1-100 which showed a tendency for improvement in efficiency. The stall margin reduced with the introduction of Gurney flap and was lowest for configuration GF1-100 which gave highest peak pressure ratio. Higher blade loading with Gurney flap was responsible for lowering the stall margin. Analysis of the flow through the blade passages has shown clear formation of trailing end vortex structure in the presence of Gurney flap that resulted in bending of the streamlines towards suction surface of the rotor blade, with consequent reduction in flow deviation and increased flow deflection, and hence increased total pressure ratio.

Effect of Inflow Circumferential Distortion on a Transonic Axial Compressor

2017 ◽  
Author(s):  
Yuyun Li ◽  
Zhiheng Wang ◽  
Guang Xi
Keyword(s):  
Total Pressure ◽  
Rotor Blade ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Leading Edge ◽  
Inlet Distortion ◽  
Compressor Rotor ◽  
Structure Changes ◽  
Transonic Axial Compressor

The Inlet distortion, which may lead to the stability reduction or structure failure, is often non-ignorable in an axial compressor. In the paper, the three-dimensional unsteady numerical simulations on the flow in NASA rotor 67 are carried out to investigate the effect of inlet distortion on the performance and flow structure in a transonic axial compressor rotor. A sinusoidal circumferential total pressure distortion with eleven periods per revolution is adopted to study the interaction between the transonic rotor and inlet circumferential distortion. Concerning the computational expense, the flow in two rotor blade passages is calculated. Various intensities of the total pressure distortion are discussed, and the detailed flow structures under different rotating speeds near the peak efficiency condition are analyzed. It is found that the distortion has a positive effect on the flow near the hub. Even though there is no apparent decrease in the rotor efficiency or total pressure ratio, an obvious periodic loading exists over the whole blade. The blade loadings are concentrated in the region near the leading edge of the rotor blade or regions affected by the oscillating shocks near the pressure side. The time averaged location of shock structure changes little with the distortion, and the motion of shocks and the interactions between the shock and the boundary layer make a great contribution to the instability of the blade structure.

Effects of Non-axisymmetric Casing Grooves Combined with Airflow Injection on Stability Enhancement of an Axial Compressor

2017 ◽  
Vol 0 (0) ◽  
Author(s):  
C. T. Dinh ◽  
K. Y. Kim
Keyword(s):  
Total Pressure ◽  
Stokes Equations ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Range Extension ◽  
Stable Range ◽  
Stall Margin ◽  
Injection Angle ◽  
Transonic Axial Compressor ◽  
Total Pressure Ratio

AbstractThis paper presents a performance evaluation of non-axisymmetric casing grooves combined with airflow injection in a transonic axial compressor with NASA Rotor 37, using three-dimensional Reynolds-averaged Navier-Stokes equations with the k-ε turbulence model. An axisymmetric casing groove was divided circumferentially into 36 non-axisymmetric grooves. The numerical results for adiabatic efficiency and total pressure ratio were validated with experimental data. A parametric study for stall margin, stable range extension, peak adiabatic efficiency, and total pressure ratio at peak adiabatic efficiency of the compressor was performed using five parameters: the front and rear lengths, the height of the casing groove, the injection mass flow rate, and the injection angle. The non-axisymmetric casing grooves combined with injection improve greatly the stall margin and stable range extension of the transonic axial compressor, but reduce only slightly the peak adiabatic efficiency in all cases, compared to the results for a smooth casing.

scholarly journals Effect of Partial Span Aspiration on the Performance of a Transonic Axial Compressor Rotor: A Numerical Study

2015 ◽  
Vol 2015 ◽  
pp. 1-13
Author(s):  
Vijaykumar Jain ◽  
Quamber H. Nagpurwala ◽  
Abdul Nassar
Keyword(s):  
Boundary Layer ◽  
Numerical Study ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Suction Side ◽  
Surface Boundary ◽  
Suction Surface ◽  
Stall Margin ◽  
Compressor Rotor ◽  
Transonic Axial Compressor

Aspiration in an axial compressor is normally regarded as sucking out the low momentum boundary layer from blade suction surface, thus lowering the chances of flow separation and consequently that of stall under off-design operation. However, the suction mass flow does not take part in useful work and leads to loss of engine power output. This paper deals with a new concept of natural aspiration to energize blade suction surface boundary layer by injecting some fluid from pressure to suction side through a part span slot on the blade. The energized boundary layer has lesser tendency to separate, thus enhancing stall margin. Numerical simulations were carried out to study the effect of aspiration slot location and geometry on the performance and stall margin of a transonic axial compressor rotor. The computational results without aspiration slot were in fair agreement with the published experimental data. The modified rotor, with part span aspiration, showed ~3.2% improvement in stall margin at design rotational speed. The pressure ratio and efficiency of the aspirated rotor dropped by ~1.42% and ~2.0%, respectively, whereas the structural analysis did not indicate any adverse effect on the blade stress distribution in the presence of aspiration slot.

A Study of Influences of Inlet Total Pressure Distortions On Clearance Flow in an Axial Compressor

2021 ◽  
Author(s):  
Guoming Zhu ◽  
Xiaolan Liu ◽  
Bo Yang ◽  
Moru Song
Keyword(s):  
Total Pressure ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Leading Edge ◽  
Stall Margin ◽  
Flow Cells ◽  
Static Pressure Distribution ◽  
Speed Flow ◽  
Clearance Flow ◽  
The Stability

Abstract The rotating distortion generated by upstream wakes or low speed flow cells is a kind of phenomenon in the inlet of middle and rear stages of an axial compressor. Highly complex inflow can obviously affect the performance and the stability of these stages, and is needed to be considered during compressor design. In this paper, a series of unsteady computational fluid dynamics (CFD) simulations is conducted based on a model of an 1-1/2 stage axial compressor to investigate the effects of the distorted inflows near the casing on the compressor performance and the clearance flow. Detailed analysis of the flow field has been performed and interesting results are concluded. The distortions, such as total pressure distortion in circumferential and radial directions, can block the tip region so that the separation loss and the mixing loss in this area are increased, and the efficiency and the total pressure ratio are dropped correspondingly. Besides, the distortions can change the static pressure distribution near the leading edge of the rotor, and make the clearance flow spill out of the rotor edge more easily under near stall condition, especially in the cases with co-rotating distortions. This phenomenon can be used to explain why the stall margin is deteriorated with nonuniform inflows.

Design and Test of a Transonic Axial Splittered Rotor

2015 ◽  
Author(s):  
Garth V. Hobson ◽  
Anthony J. Gannon ◽  
Scott Drayton
Keyword(s):  
Mass Flow ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Design Procedure ◽  
Tip Clearance ◽  
Turbine Engine ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Transonic Axial Compressor ◽  
Commercial Off The Shelf

A new design procedure was developed that uses commercial-off-the-shelf software (MATLAB, SolidWorks, and ANSYS-CFX) for the geometric rendering and analysis of a transonic axial compressor rotor with splitter blades. Predictive numerical simulations were conducted and experimental data were collected in a Transonic Compressor Rig. This study advanced the understanding of splitter blade geometry, placement, and performance benefits. In particular, it was determined that moving the splitter blade forward in the passage between the main blades, which was a departure from the trends demonstrated in the few available previous transonic axial compressor splitter blade studies, increased the mass flow range with no loss in overall performance. With a large 0.91 mm (0.036 in) tip clearance, to preserve the integrity of the rotor, the experimentally measured peak total-to-total pressure ratio was 1.69 and the peak total-to-total isentropic efficiency was 72 percent at 100 percent design speed. Additionally, a higher than predicted 7.5 percent mass flow rate range was experimentally measured, which would make for easier engine control if this concept were to be included in an actual gas turbine engine.

A Comparison between Measured and Computed Flow Fields in a Transonic Compressor Rotor

1980 ◽  
Vol 102 (4) ◽  
pp. 883-889 ◽  
Author(s):  
P. W. McDonald ◽  
C. R. Bolt ◽  
R. J. Dunker ◽  
H. B. Weyer
Keyword(s):  
Mach Number ◽  
Total Pressure ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Computational Procedure ◽  
Operating Conditions ◽  
Transonic Compressor ◽  
Compressor Rotor ◽  
Pressure Profiles

The flow field within the rotor of a transonic axial compressor has been computed and compared to measurements obtained with an advanced laser velocimeter. The compressor was designed for a total pressure ratio of 1.51 at a relative tip Mach number of 1.4. The comparisons are made at 100 percent design speed (20,260 RPM) with pressure ratios corresponding to peak efficiency, near surge, and wide open discharge operating conditions. The computational procedure iterates between a blade-to-blade calculation and an intrablade through flow calculation. Calculated Mach number contours, surface pressure distributions, and exit total pressure profiles are in agreement with the experimental data demonstrating the usefulness of quasi three-dimensional calculations in compressor design.

A CFD Study of Circumferential Groove Casing Treatments in a Transonic Axial Compressor

2010 ◽  
Author(s):  
Haixin Chen ◽  
Xudong Huang ◽  
Ke Shi ◽  
Song Fu ◽  
Matthew A. Bennington ◽  
...  
Keyword(s):  
Axial Compressor ◽  
Data Sampling ◽  
Stall Margin ◽  
Casing Treatment ◽  
Circumferential Groove ◽  
Compressor Rotor ◽  
Radial Profiles ◽  
Flow Mechanisms ◽  
Transonic Axial Compressor ◽  
And Performance

Numerical investigations were conducted to predict the performance of a transonic axial compressor rotor with circumferential groove casing treatment. The Notre Dame Transonic Axial Compressor (ND-TAC) was simulated by Tsinghua University with an in-house CFD code (NSAWET) for this work. Experimental data from the ND-TAC were used to define the geometry, boundary conditions and data sampling method for the numerical simulation. These efforts, combined with several unique simulation approaches, such as non-matched grid boundary technology to treat the periodic boundaries and interfaces between groove grids and the passage grid, resulted in good agreement between the numerical and experimental results for overall compressor performance and radial profiles of exit total pressure. Efforts were made to study blade level flow mechanisms to determine how the casing treatment impacts the compressor’s stall margin and performance. The flow structures in the passage, the tip gap and the grooves as well as their mutual interactions were plotted and analyzed. The flow and momentum transport across the tip gap in the smooth wall and the casing treatment configurations were quantitatively compared.

scholarly journals Design Optimization of a Dual-Bleeding Recirculation Channel to Enhance Operating Stability of a Transonic Axial Compressor

Energies ◽  
2021 ◽  
Vol 15 (1) ◽  
pp. 159
Author(s):  
Tien-Dung Vuong ◽  
Kwang-Yong Kim
Keyword(s):  
Design Optimization ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Aerodynamic Performance ◽  
Maximum Pressure ◽  
Stall Margin ◽  
Design Variables ◽  
Operating Stability ◽  
Transonic Axial Compressor

The present work performed a comprehensive investigation to find the effects of a dual-bleeding port recirculation channel on the aerodynamic performance of a single-stage transonic axial compressor, NASA Stage 37, and optimized the channel’s configuration to enhance the operating stability of the compressor. The compressor’s performance was examined using three parameters: The stall margin, adiabatic efficiency, and pressure ratio. Steady-state three-dimensional Reynolds-averaged Navier–Stokes analyses were performed to find the flow field and aerodynamic performance. The results showed that the addition of a bleeding channel increased the recirculation channel’s stabilizing effect compared to the single-bleeding channel. Three design variables were selected for optimization through a parametric study, which was carried out to examine the influences of six geometric parameters on the channel’s effectiveness. Surrogate-based design optimization was performed using the particle swarm optimization algorithm coupled with a surrogate model based on the radial basis neural network. The optimal design was found to increase the stall margin by 51.36% compared to the case without the recirculation channel with only 0.55% and 0.28% reductions in the peak adiabatic efficiency and maximum pressure ratio, respectively.

Sign in / Sign up

Export Citation Format

Share Document