Periodic Unsteady Tip Clearance Vortex Development in a Low Speed Axial Research Compressor at Different Tip Clearances

2017 ◽  
Author(s):  
Martin Lange ◽  
Matthias Rolfes ◽  
Ronald Mailach ◽  
Henner Schrapp
Keyword(s):  
Flow Field ◽  
Research Work ◽  
Pressure Rise ◽  
Turbulence Models ◽  
Tip Clearance ◽  
Tip Leakage Flow ◽  
Time Resolved ◽  
Low Speed ◽  
Sst Model ◽  
Tip Clearance Vortex

Since the early work on axial compressors the penalties due to radial clearances between blades and side walls are known and an ongoing focus of research work. The periodic unsteadiness of the tip clearance vortex, due to its interaction with the stator wakes, has only rarely been addressed in research papers so far. The current work presents experimental and numerical results from a four stage low speed research compressor modeling a state of the art compressor design. Time-resolved experimental measurements have been carried out at three different rotor tip clearances (gap to tip chord: 1.5%, 2.2%, 3.7%) to cover the third rotor’s casing static pressure and exit flow field. These results are compared with either steady simulations using different turbulence models or harmonic RANS calculations to discuss the periodical unsteady tip clearance vortex development at different clearance heights. The prediction of the local tip leakage flow is clearly improved by the EARSM turbulence model compared to the standard SST model. The harmonic RANS calculations (using the SST model) improve the prediction of time-averaged pressure rise and are used to analyze the rotor stator interaction in detail. The interaction of the rotor tip flow field with the passing stator wakes cause a segmentation of the tip clearance vortex and result in a sinusoidal variation in blockage downstream the rotor row.

Periodic Unsteady Tip Clearance Vortex Development in a Low-Speed Axial Research Compressor at Different Tip Clearances

2017 ◽  
Vol 140 (3) ◽  
Author(s):  
Martin Lange ◽  
Matthias Rolfes ◽  
Ronald Mailach ◽  
Henner Schrapp
Keyword(s):  
Flow Field ◽  
Research Work ◽  
Pressure Rise ◽  
Turbulence Models ◽  
Reynolds Stress Model ◽  
Tip Clearance ◽  
Tip Leakage Flow ◽  
Low Speed ◽  
Sst Model ◽  
Tip Clearance Vortex

Since the early work on axial compressors, the penalties due to radial clearances between blades and side walls are known and are an ongoing focus of research work. The periodic unsteadiness of the tip clearance vortex (TCV), due to its interaction with the stator wakes, has only rarely been addressed in research papers so far. The current work presents experimental and numerical results from a four-stage low-speed research compressor (LSRC) modeling a state-of-the-art compressor design. Time-resolved experimental measurements have been carried out at three different rotor tip clearances (gap to tip chord: 1.5%, 2.2%, 3.7%) to cover the third rotor's casing static pressure and exit flow field. These results are compared with either steady simulations using different turbulence models or harmonic Reynolds-averaged Navier–Stokes (RANS) calculations to discuss the periodical unsteady TCV development at different clearance heights. The prediction of the local tip leakage flow is clearly improved by the explicit algebraic Reynolds stress model (EARSM) turbulence model compared to the standard shear stress transport (SST) model. The harmonic RANS calculations (using the SST model) improve the prediction of time-averaged pressure rise and are used to analyze the rotor stator interaction in detail. The interaction of the rotor tip flow field with the passing stator wakes causes a segmentation of the TCV and results in a sinusoidal variation in blockage downstream the rotor row.

Characteristics of the Tip Leakage Vortex in a Low-Speed Axial Compressor With Different Rotor Tip Gaps

2012 ◽  
Author(s):  
Zhibo Zhang ◽  
Xianjun Yu ◽  
Baojie Liu
Keyword(s):  
Axial Compressor ◽  
Pressure Rise ◽  
Operating Conditions ◽  
Stereoscopic Particle Image Velocimetry ◽  
Tip Clearance ◽  
Test Facility ◽  
Tip Leakage Flow ◽  
Tip Leakage Vortex ◽  
Low Speed ◽  
Tip Leakage

The detailed evolutionary processes of the tip leakage flow/vortex inside the rotor passage are still not very clear for the difficulties of investigating of them by both experimental and numerical methods. In this paper, the flow fields near the rotor tip region inside the blade passage with two tip gaps, 0.5% and 1.5% blade height respectively, were measured by using stereoscopic particle image velocimetry (SPIV) in a large-scale low speed axial compressor test facility. The measurements are conducted at four different operating conditions, including the design, middle, maximum static pressure rise and near stall conditions. In order to analyze the variations of the characteristics of the tip leakage vortex (TLV), the trajectory, concentration, size, streamwise velocity, and the blockage parameters are extracted from the ensemble-averaged results and compared at different compressor operating conditions and tip gaps. The results show that the formation of the TLV is delayed with large tip clearance, however, its trajectory moves much faster in an approximately linear way from the blade suction side to pressure side. In the tested compressor, the size of the tip gap has little effects on the scale of the TLV in the spanwise direction, on the contrary, its effects on the pitch-wise direction is very prominent. Breakdown of the TLV were both found at the near-stall condition with different tip gaps. The location of the initiation of the TLV breakdown moves downstream from the 60% chord to 70% chord as the tip gap increases. After the TLV breakdown occurs, the flow blockage near the rotor tip region increases abruptly. The peak value of the blockage effects caused by the TLV breakdown is doubled with the tip gap size increasing from 0.5% to 1.5% blade span.

PIV Maps of Tip Leakage and Secondary Flow Fields on a Low-Speed Turbine Blade Cascade With Moving End Wall

2007 ◽  
Vol 130 (1) ◽  
Author(s):  
P. Palafox ◽  
M. L. G. Oldfield ◽  
J. E. LaGraff ◽  
T. V. Jones
Keyword(s):  
Flow Field ◽  
Secondary Flow ◽  
Field Measurements ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage Vortex ◽  
Low Speed ◽  
Tip Leakage ◽  
End Wall

New, detailed flow field measurements are presented for a very large low-speed cascade representative of a high-pressure turbine rotor blade with turning of 110deg and blade chord of 1.0m. Data were obtained for tip leakage and passage secondary flow at a Reynolds number of 4.0×105, based on exit velocity and blade axial chord. Tip clearance levels ranged from 0% to 1.68% of blade span (0% to 3% of blade chord). Particle image velocimetry was used to obtain flow field maps of several planes parallel to the tip surface within the tip gap, and adjacent passage flow. Vector maps were also obtained for planes normal to the tip surface in the direction of the tip leakage flow. Secondary flow was measured at planes normal to the blade exit angle at locations upstream and downstream of the trailing edge. The interaction between the tip leakage vortex and passage vortex is clearly defined, revealing the dominant effect of the tip leakage flow on the tip end-wall secondary flow. The relative motion between the casing and the blade tip was simulated using a motor-driven moving belt system. A reduction in the magnitude of the undertip flow near the end wall due to the moving wall is observed and the effect on the tip leakage vortex examined.

PIV Maps of Tip Leakage and Secondary Flow Fields on a Low Speed Turbine Blade Cascade With Moving Endwall

2005 ◽  
Author(s):  
P. Palafox ◽  
M. L. G. Oldfield ◽  
J. E. LaGraff ◽  
T. V. Jones
Keyword(s):  
Flow Field ◽  
Secondary Flow ◽  
Field Measurements ◽  
Turbine Rotor ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage Vortex ◽  
Low Speed ◽  
Tip Leakage

New, detailed flow field measurements are presented for a very large low-speed cascade representative of a high-pressure turbine rotor blade with turning of 110 degrees and blade chord of 1.0 m. Data was obtained for tip leakage and passage secondary flow at a Reynolds number of 4.0 × 105, based on exit velocity and blade axial chord. Tip clearance levels ranged from 0% to 1.68% of blade span (0% to 3% of blade chord). Particle Image Velocimetry (PIV) was used to obtain flow field maps of several planes parallel to the tip surface within the tip gap, and adjacent passage flow. Vector maps were also obtained for planes normal to the tip surface in the direction of the tip leakage flow. Secondary flow was measured at planes normal to the blade exit angle at locations upstream and downstream of the trailing edge. The interaction between the tip leakage vortex and passage vortex is clearly defined, revealing the dominant effect of the tip leakage flow on the tip endwall secondary flow. The relative motion between the casing and the blade tip was simulated using a motor-driven moving belt system. A reduction in the magnitude of the under-tip flow near the endwall due to the moving wall is observed and the effect on the tip leakage vortex examined.

scholarly journals Influence of Tip Clearance on Flow Characteristics of Axial Compressor

Processes ◽  
2020 ◽  
Vol 8 (11) ◽  
pp. 1445
Author(s):  
Moru Song ◽  
Hong Xie ◽  
Bo Yang ◽  
Shuyi Zhang
Keyword(s):  
Flow Field ◽  
Flow Characteristics ◽  
Axial Compressor ◽  
Suction Side ◽  
Rotating Stall ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Leakage ◽  
Tip Clearance Vortex

This paper studies the influence of tip clearance on the flow characteristics related to the performance. Based on full-passage numerical simulation with experimental validation, several clearance models are established and the performance curves are obtained. It is found that there exists an optimum clearance for the stable working range. By analyzing the flow field in tip region, the role of the tip leakage flow is illustrated. In the zero-clearance model, the separation and blockage along the suction side is the main reason for rotating stall. As the tip clearance is increased to the optimum value, the separation is suppressed by the tip leakage flow. However, with the continuing increasing of the tip clearance, the scale and strength of the tip clearance vortex is increased correspondingly. When the tip clearance is larger than the optimum value, the tip clearance vortex gradually dominates the flow field in the tip region, which can increase the unsteadiness in the tip region and trigger forward spillage in stall onset.

Study of Near-Stall Flow Behavior in a Modern Transonic Fan With Compound Sweep

2012 ◽  
Vol 134 (7) ◽  
Author(s):  
Chunill Hah ◽  
Hyoun-Woo Shin
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
Flow Structure ◽  
Flow Behavior ◽  
Pressure Rise ◽  
Tip Clearance ◽  
The Other ◽  
Other Hand ◽  
Transonic Fan ◽  
Tip Clearance Vortex

Detailed flow behavior in a modern transonic fan with a compound sweep is investigated in this paper. Both unsteady Reynolds-averaged Navier-Stokes (URANS) and large eddy simulation (LES) methods are applied to investigate the flow field over a wide operating range. The calculated flow fields are compared with the data from an array of high-frequency response pressure transducers embedded in the fan casing. The current study shows that a relatively fine computational grid is required to resolve the flow field adequately and to calculate the pressure rise across the fan correctly. The calculated flow field shows detailed flow structure near the fan rotor tip region. Due to the introduction of compound sweep toward the rotor tip, the flow structure at the rotor tip is much more stable compared to that of the conventional blade design. The passage shock stays very close to the leading edge at the rotor tip even at the throttle limit. On the other hand, the passage shock becomes stronger and detaches earlier from the blade passage at the radius where the blade sweep is in the opposite direction. The interaction between the tip clearance vortex and the passage shock becomes intense as the fan operates toward the stall limit, and tip clearance vortex breakdown occurs at near-stall operation. URANS calculates the time-averaged flow field fairly well. Details of measured rms static pressure are not calculated with sufficient accuracy with URANS. On the other hand, LES calculates details of the measured unsteady flow features in the current transonic fan with compound sweep fairly well and reveals the flow mechanism behind the measured unsteady flow field.

Experimental Investigation Into the Effects of the Steady Wake-Tip Clearance Vortex Interaction in a Compressor Cascade

2015 ◽  
Vol 137 (6) ◽  
Author(s):  
Andreas Krug ◽  
Peter Busse ◽  
Konrad Vogeler
Keyword(s):  
Flow Field ◽  
Experimental Studies ◽  
Axial Compressor ◽  
Field Measurements ◽  
Tip Clearance ◽  
Compressor Cascade ◽  
Unsteady Interaction ◽  
Linear Compressor Cascade ◽  
Tip Clearance Vortex ◽  
The Impact

An important aspect of the aerodynamic flow field in the tip region of axial compressor rotors is the unsteady interaction between the tip clearance vortex (TCV) and the incoming stator wakes. In order to gain an improved understanding of the mechanics involved, systematic studies need to be performed. As a first step toward the characterization of the dynamic effects caused by the relative movement of the blade rows, the impact of a stationary wake-induced inlet disturbance on a linear compressor cascade with tip clearance will be analyzed. The wakes were generated by a fixed grid of cylindrical bars with variable pitch being placed at discrete pitchwise positions. This paper focuses on experimental studies conducted at the newly designed low-speed cascade wind tunnel in Dresden. The general tunnel configuration and details on the specific cascade setup will be presented. Steady state flow field measurements were carried out using five-hole probe traverses up- and downstream of the cascade and accompanied by static wall pressure readings. 2D-particle image velocimetry (PIV) measurements complemented these results by visualizing the blade-to-blade flow field. Hence, the structure of the evolving secondary flow system is evaluated and compared for all tested configurations.

Evaluating the Influence of Rotor-Casing Eccentricity on Turbine Efficiency Including Time-Resolved Flow Field Measurements

2021 ◽  
pp. 1-33
Author(s):  
Eric DeShong ◽  
Shawn Siroka ◽  
Reid A. Berdanier ◽  
Karen A. Thole
Keyword(s):  
Flow Field ◽  
Magnetic Levitation ◽  
Field Measurements ◽  
Tip Clearance ◽  
Time Resolved ◽  
Flow Angle ◽  
Turbine Efficiency ◽  
Eccentric Rotor ◽  
Blade Tip ◽  
Manufacturing Techniques

Abstract The clearance that exists between the casing and turbine blade tips is one of the key drivers of efficiency in gas turbine engines. For this reason, engine manufacturers utilize precise manufacturing techniques and may employ clearance control systems to minimize tip clearances to reduce associated losses. Despite these efforts, turbines typically exhibit some nominal casing ovality or rotor-casing eccentricity, and changes to blade tip clearance during operation commonly occur due to thermal and mechanical stresses. The present study investigates non-axisymmetric tip clearance effects by creating a rotor-casing eccentricity in a one-stage axial test turbine operating in a continuous-duration mode at engine relevant conditions with engine representative hardware. A magnetic levitation bearing system was leveraged to move the turbine shaft to vary the rotor-casing eccentricity without test section disassembly. The results of this study indicate that rotor-casing eccentricity does not affect overall turbine efficiency over the range that was tested, but does locally influence efficiency and the rotor exit flow field. Comparisons of flow angle and secondary flow kinetic energy agreed with previous studies and existing analytical methods, respectively. Collectively, these results indicate that tip clearance can be studied locally on an eccentric rotor.

Aerodynamic-Rotordynamic Interaction in Axial Compression Systems—Part I: Modeling and Analysis of Fluid-Induced Forces

2003 ◽  
Vol 125 (3) ◽  
pp. 405-415
Author(s):  
Ammar A. Al-Nahwi ◽  
James D. Paduano ◽  
Samir A. Nayfeh
Keyword(s):  
Flow Field ◽  
Axial Compressor ◽  
Pressure Rise ◽  
Essential Element ◽  
Rotor Blades ◽  
Tip Clearance ◽  
Analytical Models ◽  
Modeling And Analysis ◽  
Equal Importance ◽  
Consistent Treatment

This paper presents a first principles-based model of the fluid-induced forces acting on the rotor of an axial compressor. These forces are primarily associated with the presence of a nonuniform flow field around the rotor, such as that produced by a rotor tip clearance asymmetry. Simple, analytical expressions for the forces as functions of basic flow field quantities are obtained. These expressions allow an intuitive understanding of the nature of the forces and—when combined with a rudimentary model of an axial compressor flow field (the Moore-Greitzer model)—enable computation of the forces as a function of compressor geometry, torque and pressure-rise characteristics, and operating point. The forces predicted by the model are also compared to recently published measurements and more complex analytical models, and are found to be in reasonable agreement. The model elucidates that the fluid-induced forces comprise three main contributions: fluid turning in the rotor blades, pressure distribution around the rotor, and unsteady momentum storage within the rotor. The model also confirms recent efforts in that the orientation of fluid-induced forces is locked to the flow nonuniformity, not to tip clearance asymmetry as is traditionally assumed. The turning and pressure force contributions are shown to be of comparable magnitudes—and therefore of equal importance—for operating points between the design point and the peak of the compressor characteristic. Within this operating range, both “forward” and “backward” rotor whirl tendencies are shown to be possible. This work extends recent efforts by developing a more complete, yet compact, description of fluid-induced forces in that it accounts for all relevant force contributions, both tangential and radial, that may influence the dynamics of the rotor. Hence it constitutes an essential element of a consistent treatment of rotordynamic stability under the action of fluid-induced forces, which is the subject of Part II of this paper.

The Influence of Geometry Deformation on a Multistage Compressor

2018 ◽  
Author(s):  
Xin Teng ◽  
WuLi Chu ◽  
HaoGuang Zhang ◽  
Kai Liu ◽  
JinGe Li
Keyword(s):  
Flow Field ◽  
Pressure Rise ◽  
Tip Clearance ◽  
Field Analysis ◽  
Dominant Factor ◽  
Accurate Estimation ◽  
Time Operation ◽  
Different Types ◽  
Multistage Compressor ◽  
Stagger Angle

Over the service time, the rotating parts of turbine engine vary in their geometry. When aircraft take off or fly through a volcanic ash cloud, the particles are sucked into the engine, impinge the blade and gradually erode the surface. The impinging between particles and blades is responsible for the increase of the surface roughness. Also, during the long-time operation, the function of the blade’s stacking law combined with the centrifugal force could cause deviation of the stagger angle. Moreover, blade tip clearance could vary because of the casing deformation. All the deformation of geometry could severely reduce the engine performance and thus engine life. The work presented in this paper focused on the influence of geometry deformation in a real low-pressure compressor. The investigation is more difficult than most of the previously published researches with a total of five stages being considered. Due to the irregularities in geometry, it is difficult to numerically assess the performance of the compressor. The aim of this study is to give an analysis method that allows an efficient and accurate estimation of the performance for multistage compressor with geometry deformation. In the first step, the geometry models with different deviation in tip clearance, roughness and stagger angle were established respectively. A CFD study was then applied to the compressor with RANS method to calculate the flow field with different types of deformation. The variation of overall performance due to the deformation was finally analyzed to identify the dominant factor on influencing the performance of the compressor among different types of geometry deformation. A method based on polytropic efficiency analysis and flow field analysis was also established to specifically analyze which stage is most sensitive to the geometry deformation. The results show a significant influence of geometric deformation on the efficiency, total pressure rise and flow range of the multistage compressor. The conclusions of this study would provide an important guidance for engine overhaul in the factory.

Sign in / Sign up

Export Citation Format

Share Document