scholarly journals Off-Design Performance Comparison Between Single and Two-Shaft Engines: Part 1 — Fixed Geometry

2020 ◽  
Author(s):  
Th. Nikolaidis ◽  
A. Pellegrini ◽  
H. I. H. Saravanamuttoo ◽  
I. Aslanidou ◽  
A. Kalfas ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Mass Flow ◽  
Thermal Efficiency ◽  
Rotational Speed ◽  
Pressure Ratio ◽  
Performance Comparison ◽  
Part Load ◽  
Design Performance ◽  
Research Activities ◽  
Compressor Pressure Ratio

Abstract This paper describes an investigation into the off-design performance comparison of single and two-shaft gas turbine engines. A question that has been asked for a long time which gas turbine delivers a better thermal efficiency at part load. The authors, notwithstanding their intensive searches, were unable to find a comprehensive answer to this question. A detailed investigation was carried out using a state of the art performance evaluation method and the answer was found to be: It depends! In this work, the performance of two engine configurations is assessed. In the first one, the single-shaft gas turbine operates at constant shaft rotational speed. Thus, the shape of the compressor map rotational speed line will have an important influence on the performance of the engine. To explore the implications of the shape of the speed line, two single-shaft cases are examined. The first case is when the speed line is curved and as the compressor pressure ratio falls, the non-dimensional mass flow increases. The second case is when the speed line is vertical and as the compressor pressure ratio falls, the non-dimensional mass flow remains constant. In the second configuration, the two-shaft engine, the two-shafts can be controlled to operate at different rotational speeds and also varying relationships between the rotational speeds. The part-load operation is characterized by a reduction in the gas generator rotational speed. The tool, which was used in this study, is a 0-D whole engine simulation tool, named Turbomatch. It was developed at Cranfield and it is based on mass and energy balance, carried out through an iterative method, which is based on component maps. These generic, experimentally derived maps are scaled to match the design point of a particular engine before an off-design calculation is performed. The code has been validated against experimental data elsewhere, it has been used extensively for academic purposes and the research activities that have taken place at Cranfield University. For an ideal cycle, the single-shaft engine was found to be a clear winner in terms of part-load thermal efficiency. However, this picture changed when realistic component maps were utilized. The basic cycle and the shape of component maps had a profound influence on the outcome. The authors explored the influence of speed line shapes, levels of component efficiencies and the variation of these component efficiencies within the operating range. This paper describes how each one of these factors, individually, influences the outcome.

Genetic Optimization of Steam Injected Gas Turbine Power Plants

2002 ◽  
Author(s):  
Ibrahim Sinan Akmandor ◽  
O¨zhan O¨ksu¨z ◽  
Sec¸kin Go¨kaltun ◽  
Melih Han Bilgin
Keyword(s):  
Gas Turbine ◽  
Power Output ◽  
Thermal Efficiency ◽  
Gas Turbines ◽  
Power Plants ◽  
Pressure Ratio ◽  
Steam Injection ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Compressor Pressure Ratio

A new methodology is developed to find the optimal steam injection levels in simple and combined cycle gas turbine power plants. When steam injection process is being applied to simple cycle gas turbines, it is shown to offer many benefits, including increased power output and efficiency as well as reduced exhaust emissions. For combined cycle power plants, steam injection in the gas turbine, significantly decreases the amount of flow and energy through the steam turbine and the overall power output of the combined cycle is decreased. This study focuses on finding the maximum power output and efficiency of steam injected simple and combined cycle gas turbines. For that purpose, the thermodynamic cycle analysis and a genetic algorithm are linked within an automated design loop. The multi-parameter objective function is either based on the power output or on the overall thermal efficiency. NOx levels have also been taken into account in a third objective function denoted as steam injection effectiveness. The calculations are done for a wide range of parameters such as compressor pressure ratio, turbine inlet temperature, air and steam mass flow rates. Firstly, 6 widely used simple and combined cycle power plants performance are used as test cases for thermodynamic cycle validation. Secondly, gas turbine main parameters are modified to yield the maximum generator power and thermal efficiency. Finally, the effects of uniform crossover, creep mutation, different random number seeds, population size and the number of children per pair of parents on the performance of the genetic algorithm are studied. Parametric analyses show that application of high turbine inlet temperature, high air mass flow rate and no steam injection lead to high power and high combined cycle thermal efficiency. On the contrary, when NOx reduction is desired, steam injection is necessary. For simple cycle, almost full amount of steam injection is required to increase power and efficiency as well as to reduce NOx. Moreover, it is found that the compressor pressure ratio for high power output is significantly lower than the compressor pressure ratio that drives the high thermal efficiency.

Thermodynamic and Energy Study of a Regenerator in Gas Turbine Cycle and Optimization of Performances

2016 ◽  
Vol 5 (2) ◽  
pp. 25-44
Author(s):  
Saria Abed ◽  
Taher Khir ◽  
Ammar Ben Brahim
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Thermal Efficiency ◽  
Parametric Study ◽  
Pressure Ratio ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Compressor Pressure Ratio ◽  
Compressor Inlet ◽  
Gas Turbine Cycle

In this paper, thermodynamic study of simple and regenerative gas turbine cycles is exhibited. Firstly, thermodynamic models for both cycles are defined; thermal efficiencies of both cycles are determined, the overall heat transfer coefficient through the heat exchanger is calculated in order to determinate its performances and parametric study is carried out to investigate the effects of compressor inlet temperature, turbine inlet temperature and compressor pressure ratio on the parameters that measure cycles' performance. Subsequently, numerical optimization is established through EES software to determinate operating conditions. The results of parametric study have shown a significant impact of operating parameters on the performance of the cycle. According to this study, the regeneration technique improves the thermal efficiency by 10%. The studied regenerator has an important effectiveness (˜ 82%) which improves the heat transfer exchange; also a high compressor pressure ratio and an important combustion temperature can increase thermal efficiency.

Improvements in Part-Load Efficiency by Reducing Pressure Ratio in Regenerative Gas-Turbine Engines

1985 ◽  
Author(s):  
Theodosios P. Korakianitis ◽  
David Gordon Wilson
Keyword(s):  
Heat Exchanger ◽  
Gas Turbine ◽  
Heat Exchangers ◽  
Pressure Ratio ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Design Point ◽  
Part Load ◽  
Compressor Pressure Ratio ◽  
Point Pressure

To obtain equal thermal efficiencies in gas-turbine engines, designers have the freedom (if space and mass constraints are not limiting) of exchanging compressor pressure ratio for heat-exchanger effectiveness. Because heat exchangers can have lower losses than compressors, a high-effectiveness heat-exchanger cycle can have a much higher thermal efficiency (theoretically 55–60%) than is possible with unregenerated cycles. What has not been known up to now is the effect of design-point pressure ratio on the part-load efficiency of gas-turbine engines. The work reported here shows that, for similar turbomachinery technology, design-point and part-load efficiencies improve as the design-point pressure ratio decreases and the heat-exchanger thermal ratio increases.

Proposal of Innovative Gas Turbine Combined Cycle Power Generation System

2004 ◽  
Author(s):  
Hideto Moritsuka
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Thermal Efficiency ◽  
Pressure Ratio ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Generation System ◽  
Turbine Inlet Temperature ◽  
Turbine Inlet ◽  
Power Generation System

In order to estimate the possibility to improve thermal efficiency of power generation use gas turbine combined cycle power generation system, benefits of employing the advanced gas turbine technologies proposed here have been made clear based on the recently developed 1500C-class steam cooling gas turbine and 1300C-class reheat cycle gas turbine combined cycle power generation systems. In addition, methane reforming cooling method and NO reducing catalytic reheater are proposed. Based on these findings, the Maximized efficiency Optimized Reheat cycle Innovative Gas Turbine Combined cycle (MORITC) Power Generation System with the most effective combination of advanced technologies and the new devices have been proposed. In case of the proposed reheat cycle gas turbine with pressure ratio being 55, the high pressure turbine inlet temperature being 1700C, the low pressure turbine inlet temperature being 800C, combined with the ultra super critical pressure, double reheat type heat recovery Rankine cycle, the thermal efficiency of combined cycle are expected approximately 66.7% (LHV, generator end).

Centrifugal Compressor Performance Prediction Using Gaussian Process Regression and Artificial Neural Networks

2019 ◽  
Author(s):  
Pau Cutrina Vilalta ◽  
Hui Wan ◽  
Soumya S. Patnaik
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Centrifugal Compressor ◽  
Rotational Speed ◽  
Data Augmentation ◽  
Pressure Ratio ◽  
Gaussian Process Regression ◽  
Compressor Performance ◽  
Artificial Neural

Abstract In this paper, we use various regression models and Artificial Neural Network (ANN) to predict the centrifugal compressor performance map. Particularly, we study the accuracy and efficiency of Gaussian Process Regression (GPR) and Artificial Neural Networks in modelling the pressure ratio, given the mass flow rate and rotational speed of a centrifugal compressor. Preliminary results show that both GPR and ANN can predict the compressor performance map well, for both interpolation and extrapolation. We also study the data augmentation and data minimzation effects using the GPR. Due to the inherent pressure ratio data distribution in mass-flow-rate and rotational-speed space, data augmentation in the rotational speed is more effective to improve the ANN performance than the mass flow rate data augmentation.

scholarly journals Conceptual Mean-Line Design of Single and Twin-Shaft Oxy-Fuel Gas Turbine in a Semiclosed Oxy-Fuel Combustion Combined Cycle

2013 ◽  
Vol 135 (8) ◽  
Author(s):  
Majed Sammak ◽  
Egill Thorbergsson ◽  
Tomas Grönstedt ◽  
Magnus Genrup
Keyword(s):  
Mach Number ◽  
Gas Turbine ◽  
Mass Flow ◽  
Rotational Speed ◽  
Gas Turbines ◽  
Combined Cycle ◽  
Fuel Gas ◽  
Power Turbine ◽  
Exit Mach Number ◽  
Line Design

The aim of this study was to compare single- and twin-shaft oxy-fuel gas turbines in a semiclosed oxy-fuel combustion combined cycle (SCOC–CC). This paper discussed the turbomachinery preliminary mean-line design of oxy-fuel compressor and turbine. The conceptual turbine design was performed using the axial through-flow code luax-t, developed at Lund University. A tool for conceptual design of axial compressors developed at Chalmers University was used for the design of the compressor. The modeled SCOC–CC gave a net electrical efficiency of 46% and a net power of 106 MW. The production of 95% pure oxygen and the compression of CO2 reduced the gross efficiency of the SCOC–CC by 10 and 2 percentage points, respectively. The designed oxy-fuel gas turbine had a power of 86 MW. The rotational speed of the single-shaft gas turbine was set to 5200 rpm. The designed turbine had four stages, while the compressor had 18 stages. The turbine exit Mach number was calculated to be 0.6 and the calculated value of AN2 was 40 · 106 rpm2m2. The total calculated cooling mass flow was 25% of the compressor mass flow, or 47 kg/s. The relative tip Mach number of the compressor at the first rotor stage was 1.15. The rotational speed of the twin-shaft gas generator was set to 7200 rpm, while that of the power turbine was set to 4800 rpm. A twin-shaft turbine was designed with five turbine stages to maintain the exit Mach number around 0.5. The twin-shaft turbine required a lower exit Mach number to maintain reasonable diffuser performance. The compressor turbine was designed with two stages while the power turbine had three stages. The study showed that a four-stage twin-shaft turbine produced a high exit Mach number. The calculated value of AN2 was 38 · 106 rpm2m2. The total calculated cooling mass flow was 23% of the compressor mass flow, or 44 kg/s. The compressor was designed with 14 stages. The preliminary design parameters of the turbine and compressor were within established industrial ranges. From the results of this study, it was concluded that both single- and twin-shaft oxy-fuel gas turbines have advantages. The choice of a twin-shaft gas turbine can be motivated by the smaller compressor size and the advantage of greater flexibility in operation, mainly in the off-design mode. However, the advantages of a twin-shaft design must be weighed against the inherent simplicity and low cost of the simple single-shaft design.

Development of an 8MW-Class High-Efficiency Gas Turbine, M7A-03

2007 ◽  
Author(s):  
Kazuhiko Tanimura ◽  
Naoki Murakami ◽  
Akinori Matsuoka ◽  
Katsuhiko Ishida ◽  
Hiroshi Kato ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Thermal Efficiency ◽  
High Performance ◽  
High Efficiency ◽  
High Reliability ◽  
Pressure Ratio ◽  
Combined Cycle ◽  
Gas Temperature ◽  
Turbine Cooling ◽  
Distributed Power Generation

The M7A-03 gas turbine, an 8 MW class, single shaft gas turbine, is the latest model of the Kawasaki M7A series. Because of the high thermal efficiency and the high exhaust gas temperature, it is particularly suitable for distributed power generation, cogeneration and combined-cycle applications. About the development of M7A-03 gas turbine, Kawasaki has taken the experience of the existing M7A-01 and M7A-02 series into consideration, as a baseline. Furthermore, the latest technology of aerodynamics and cooling design, already applied to the 18 MW class Kawasaki L20A, released in 2000, has been applied to the M7A-03. Kawasaki has adopted the design concept for achieving reliability within the shortest possible development period by selecting the same fundamental engine specifications of the existing M7A-02 – mass air flow rate, pressure ratio, TIT, etc. However, the M7A-03 has been attaining a thermal efficiency of greater than 2.5 points higher and an output increment of over 660 kW than the M7A-02, by the improvement in aerodynamic performance of the compressor, turbine and exhaust diffuser, improved turbine cooling, and newer seal technology. In addition, the NOx emission of the combustor is low and the M7A-03 has a long service life. These functions make long-term continuous operation possible under various environmental restraints. Lower life cycle costs are achieved by the engine high performance, and the high-reliability resulting from simple structure. The prototype M7A-03 gas-turbine development test started in the spring of 2006 and it has been confirmed that performance, mechanical characteristics, and emissions have achieved the initial design goals.

Evaluation of Axial Compressor Characteristics Under Overspray Condition

2013 ◽  
Author(s):  
Chihiro Myoren ◽  
Yasuo Takahashi ◽  
Manabu Yagi ◽  
Takanori Shibata ◽  
Tadaharu Kishibe
Keyword(s):  
Gas Turbine ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Water Mass ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Test Facility ◽  
Compressor Performance ◽  
Water Mass Flow Rate

An axial compressor was developed for an industrial gas turbine equipped with a water atomization cooling (WAC) system, which is a kind of inlet fogging technique with overspray. The compressor performance was evaluated using a 40MW-class test facility for the advanced humid air turbine system. A prediction method to estimate the effect of WAC was developed for the design of the compressor. The method was based on a streamline curvature (SLC) method implementing a droplet evaporation model. Four test runs with WAC have been conducted since February 2012. The maximum water mass flow rate was 1.2% of the inlet mass flow rate at the 4th test run, while the design value was 2.0%. The results showed that the WAC decreased the inlet and outlet temperatures compared with the DRY (no fogging) case. These decreases changed the matching point of the gas turbine, and increased the mass flow rate and the pressure ratio by 1.8% and 1.1%, respectively. Since prediction results agreed with the results of the test run qualitatively, the compressor performance improvement by WAC was confirmed both experimentally and analytically. The test run with the design water mass flow rate is going to be conducted in the near future.

Parameter Optimization on Combined Gas Turbine-Fuel Cell Power Plants

2005 ◽  
Vol 2 (4) ◽  
pp. 268-273 ◽  
Author(s):  
Rainer Kurz
Keyword(s):  
Fuel Cell ◽  
Gas Turbine ◽  
Power Plants ◽  
Pressure Ratio ◽  
Design Parameters ◽  
Turbine Efficiency ◽  
Compressor Pressure Ratio ◽  
Turbine Design ◽  
Cycle Efficiency ◽  
Compressor Efficiency

A thermodynamic model for a gas turbine-fuel cell hybrid is created and described in the paper. The effects of gas turbine design parameters such as compressor pressure ratio, compressor efficiency, turbine efficiency, and mass flow are considered. The model allows to simulate the effects of fuel cell design parameters such as operating temperature, pressure, fuel utilization, and current density on the cycle efficiency. This paper discusses, based on a parametric study, optimum design parameters for a hybrid gas turbine. Because it is desirable to use existing gas turbine designs for the hybrids, the requirements for this hybridization are considered. Based on performance data for a typical 1600hp industrial single shaft gas turbine, a model to predict the off-design performance is developed. In the paper, two complementary studies are performed: The first study attempts to determine the range of cycle parameters that will lead to a reasonable cycle efficiency. Next, an existing gas turbine, that fits into the previously established range of parameters, will be studied in more detail. Conclusions from this paper include the feasibility of using existing gas turbine designs for the proposed cycle.

Influence of Steam Injection on Thermal Efficiency and Operating Temperature of GE-F5 Gas Turbines Applying VODOLEY System

2005 ◽  
Author(s):  
Mohsen Ghazikhani ◽  
Nima Manshoori ◽  
Davood Tafazoli
Keyword(s):  
Power Plant ◽  
Ambient Temperature ◽  
Gas Turbine ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Thermal Efficiency ◽  
Gas Turbines ◽  
Steam Injection ◽  
Gas Turbine Cycle

An industrial gas turbine has the characteristic that turbine output decreases on hot summer days when electricity demand peaks. For GE-F5 gas turbines of Mashad Power Plant when ambient temperature increases 1° C, compressor outlet temperature increases 1.13° C and turbine exhaust temperature increases 2.5° C. Also air mass flow rate decreases about 0.6 kg/sec when ambient temperature increases 1° C, so it is revealed that variations are more due to decreasing in the efficiency of compressor and less due to reduction in mass flow rate of air as ambient temperature increases in constant power output. The cycle efficiency of these GE-F5 gas turbines reduces 3 percent with increasing 50° C of ambient temperature, also the fuel consumption increases as ambient temperature increases for constant turbine work. These are also because of reducing in the compressor efficiency in high temperature ambient. Steam injection in gas turbines is a way to prevent a loss in performance of gas turbines caused by high ambient temperature and has been used for many years. VODOLEY system is a steam injection system, which is known as a self-sufficient one in steam production. The amount of water vapor in combustion products will become regenerated in a contact condenser and after passing through a heat recovery boiler is injected in the transition piece after combustion chamber. In this paper the influence of steam injection in Mashad Power Plant GE-F5 gas turbine parameters, applying VODOLEY system, is being observed. Results show that in this turbine, the turbine inlet temperature (T3) decreases in a range of 5 percent to 11 percent depending on ambient temperature, so the operating parameters in a gas turbine cycle equipped with VODOLEY system in 40° C of ambient temperature is the same as simple gas turbine cycle in 10° C of ambient temperature. Results show that the thermal efficiency increases up to 10 percent, but Back-Work ratio increases in a range of 15 percent to 30 percent. Also results show that although VODOLEY system has water treatment cost but by using this system the running cost will reduce up to 27 percent.

Sign in / Sign up

Export Citation Format

Share Document