Heat Transfer Analysis of Human Cell Culture Under RF Exposure

2005 ◽  
Author(s):  
Muhammad Khalid ◽  
Chenn Zhou ◽  
Ashish Bassi ◽  
San Ming Wang ◽  
Howard Gerber ◽  
...  
Keyword(s):  
Gene Expression ◽  
Heat Transfer ◽  
Electric Field ◽  
Fluid Dynamic ◽  
Operating Conditions ◽  
Heat Transfer Analysis ◽  
Heat Shock Gene ◽  
Exposure System ◽  
Finite Element Software ◽  
Rf Exposure

A 2.45 GHz radio frequency (RF) exposure system was designed and used to study the RF effects on the genome-wide gene expression in cultured human cells. In this system, a T-25 culture flask, which contains 10 × 106 cells in a 10ml medium, is placed in a WR 340 waveguide. The waveguide serves as an environmental chamber. The source is a pulsed magnetron for obtaining a high electric field with the specific absorption rate (SAR) at approximately 10 W/kg. In order to ensure the non-thermal effect, the system was designed to maintain a temperature of 37°C. In this research, the heat transfer analysis of the system was conducted using the computational fluid dynamic (CFD) software FLUENT® coupled with the finite element software, High Frequency Structural Simulation (HFSS) by Ansoft. The electric field was first analyzed by using HFSS to calculate the SAR distribution as a heat source input for CFD calculations. The fluid flow and temperature distributions within the flask were then analyzed using FLUENT®. The results were validated experimentally by measuring the temperatures with fluoroptic thermometer probes as well as by examining the level of heat shock gene expression. These results provide useful information for a better understanding and controlling of the operating conditions of the system.

scholarly journals Experimental performance comparison between circular and elliptical tubes in evaporative condensers

2021 ◽  
Author(s):  
Giuseppe Starace ◽  
Lorenzo Falcicchia ◽  
Pierpaolo Panico ◽  
Maria Fiorentino ◽  
Gianpiero Colangelo
Keyword(s):  
Heat Transfer ◽  
Experimental Approach ◽  
Fluid Dynamic ◽  
Major Axis ◽  
Performance Comparison ◽  
Operating Conditions ◽  
Condensation Temperature ◽  
Air Cooled Condensers ◽  
Reduced Scale ◽  
Dynamic Phenomena

AbstractIn refrigeration systems, evaporative condensers have two main advantages compared to other condensation heat exchangers: They operate at lower condensation temperature than traditional air-cooled condensers and require a lower quantity of water and pumping power compared to evaporative towers. The heat and mass transfer that occur on tube batteries are difficult to study. The aim of this work is to apply an experimental approach to investigate the performance of an evaporative condenser on a reduced scale by means of a test bench, consisting of a transparent duct with a rectangular test section in which electric heaters, inside elliptical pipes (major axis 32 mm, minor axis 23 mm), simulate the presence of the refrigerant during condensation. By keeping the water conditions fixed and constant, the operating conditions of the air and the inclination of the heat transfer geometry were varied, and this allowed to carry out a sensitivity analysis, depending on some of the main parameters that influence the thermo-fluid dynamic phenomena, as well as a performance comparison. The results showed that the heat transfer increases with the tube surface exposed directly to the air as a result of the increase in their inclination, that has been varied in the range 0–20°. For the investigated conditions, the average increase, resulting by the inclination, is 28%.

Numerical Simulation on Heat Dissipating Performance of New Pipe with Grid Plate

2012 ◽  
Vol 532-533 ◽  
pp. 417-421
Author(s):  
Chang Li Song ◽  
Jing Ji
Keyword(s):  
Heat Transfer ◽  
Simulation Analysis ◽  
Heat Transfer Analysis ◽  
Finite Element Software ◽  
Grid Plate ◽  
Steady State Heat ◽  
Steady State Heat Transfer ◽  
Energy Conservation Law ◽  
Optimal Diameter ◽  
Selection Of

In order to improve the pipe dissipating area, a kind of new pipe with grid plate is proposed in this paper. Based on the basic principle of heat transfer and energy conservation law, by finite element software ANSYS the simulation analysis of the steady-state heat transfer of the new pipeline is carried out, process of ANSYS modeling, loading and solving is introduced in detail, the distribution of temperature and stress for pipe with a grid plate is given, these can provide the foundation for the selection of the optimal diameter of the grid plate and transient heat transfer analysis of pipe.

Conjugate Heat Transfer Analysis for Gas Turbine Cooled Stator

2012 ◽  
Author(s):  
Kuo-San Ho ◽  
Christopher Urwiller ◽  
S. Murthy Konan ◽  
Jong S. Liu ◽  
Bruno Aguilar
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Test Data ◽  
Conjugate Heat Transfer ◽  
Fluid Dynamic ◽  
Thermal Analyses ◽  
Convection Heat Transfer ◽  
Heat Transfer Analysis ◽  
Engine Test ◽  
Adiabatic Wall

This paper explores the conjugate heat transfer (CHT) numerical simulation approach to calculate the metal temperature for the gas turbine cooled stator. ANSYS CFX12.1 code was selected to be the computational fluid dynamic (CFD) tool to perform the CHT simulation. The 2-equation RNG k-ε turbulence model with scalable modified wall function was employed. A full engine test with thermocouple measurement was performed and used to validate the CHT results. Metal temperatures calculated with the CHT model were compared to engine test data. The results demonstrated good agreement between test data and airfoil metal temperatures and cooling flow temperatures using the CHT model. However, the CHT calculations in the outer end wall had a discrepancy compared to the measured temperatures, which was due to the fact that the CHT model assumed an adiabatic wall as a boundary condition. This paper presents a process to calculate convection heat transfer coefficient (HTC) for cooling passages and airfoil surfaces using CHT results. This process is possible because local wall heat flux and fluid temperatures are known. This approach assists in calibrating an in-house conduction thermal model for steady state and transient thermal analyses.

One-Dimensional Zonal Model for the Unsteady Heat Transfer Analysis in an Open Volumetric Air Receiver

2020 ◽  
Vol 13 (1) ◽  
Author(s):  
Gurveer Singh ◽  
Vishwa Deepak Kumar ◽  
Laltu Chandra ◽  
R. Shekhar ◽  
P. S. Ghoshdastidar
Keyword(s):  
Heat Transfer ◽  
High Heat ◽  
Operating Conditions ◽  
Heat Transfer Analysis ◽  
Transfer Model ◽  
High Heat Flux ◽  
Unsteady Heat Transfer ◽  
Volumetric Heating ◽  
One Dimensional ◽  
Zonal Model

Abstract The open volumetric air receiver (OVAR)-based central solar thermal systems provide air at a temperature > 1000 K. Such a receiver is comprised of porous absorbers, which are exposed to a high heat-flux > 800 Suns (1 Sun = 1 kW/m2). A reliable assessment of heat transfer in an OVAR is necessary to operate such a receiver under transient conditions. Based on a literature review, the need for developing a comprehensive, unsteady, heat transfer model is realized. In this paper, a seven-equations based, one-dimensional, zonal model is deduced. This includes heat transfer in porous absorber, primary-air, return-air, receiver casing, and their detailed interaction. The zonal model is validated with an inhouse experiment showing its predictive capability, for unsteady and steady conditions, within the reported uncertainty of ±7%. The validated model is used for investigating the effect of operating conditions and absorber geometry on the thermal performance of an absorber. Some of the salient observations are (a) the maximum absorber porosity of 70–90% may be preferred for non-volumetric and volumetric-heating conditions, (b) the minimum air-return ratio should be 0.7, and (c) the smallest gap to absorber-length ratio of 0.2 should suffice. Finally, suggestions are provided for extending the model.

Thermo Fluid Dynamic Analysis of a Gas Turbine Transition-Piece

2014 ◽  
Author(s):  
Riccardo Da Soghe ◽  
Cosimo Bianchini ◽  
Antonio Andreini ◽  
Lorenzo Mazzei ◽  
Giovanni Riccio ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Gas Turbine ◽  
Fluid Dynamic ◽  
Gas Turbine Engine ◽  
Operating Conditions ◽  
Thermal Loads ◽  
Turbine Engine ◽  
Transition Piece

The transition-piece of a gas turbine engine is subjected to high thermal loads as it collects high temperature combustion products from the gas generator to a turbine. This generally produces high thermal stress levels in the casing of the transition piece, strongly limiting its life expectations and making it one of the most critical components of the entire engine. The reliable prediction of such thermal loads is hence a crucial aspect to increase the transition-piece life span and to assure safe operations. The present study aims to investigate the aero-thermal behaviour of a gas turbine engine transition-piece and in particular to evaluate working temperatures of the casing in relation to the flow and heat transfer situation inside and outside the transition-piece. Typical operating conditions are considered to determine the amount of heat transfer from the gas to the casing by means of CFD. Both conjugate approach and wall fixed temperature have been considered to compute the heat transfer coefficient, and more in general, the transition-piece thermal loads. Finally a discussion on the most convenient heat transfer coefficient expression is provided.

Time-Resolved Heat Transfer and Fluid Dynamic Analysis of Natural Convection From Isothermal Horizontal Cylinders

2010 ◽  
Author(s):  
Tim Persoons ◽  
Ian M. O. Gorman ◽  
Gerry Byrne ◽  
Darina B. Murray
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Fluid Dynamic ◽  
Vertical Cylinder ◽  
Local Heat Transfer ◽  
Temporal Analysis ◽  
Local Heat ◽  
Operating Conditions ◽  
Thermal Plume ◽  
Horizontal Cylinders

This paper discusses the close coupling between fluid dynamics and local natural convection heat transfer rates from a pair of isothermally heated horizontal cylinders submerged in water. The presence of a second heated cylinder induces heat transfer enhancements of up to 10%, and strong fluctuations in local heat transfer rate. Therefore specific attention is focused on how the local heat transfer characteristics of the upper cylinder are affected by buoyancy induced fluid flow from the lower cylinder. The paper investigates a range of Rayleigh number between 2·106 and 6·106, and a vertical cylinder spacing between 2D and 4D. Simultaneous local heat flux measurements and flow velocity measurements using particle image velocimetry reveal oscillatory behaviour of the thermal plume, depending on operating conditions. A joint temporal analysis of the data has provided new insights into the governing mechanisms, which enables further optimisation of the heat transfer performance.

Heat Transfer Augmentation of Parallel Flows by Means of Electric Conduction Phenomenon in Macro- and Micro-Scale

2009 ◽  
Author(s):  
Miad Yazdani ◽  
Jamal Seyed-Yagoobi
Keyword(s):  
Heat Transfer ◽  
Electric Field ◽  
Channel Wall ◽  
External Pressure ◽  
Operating Conditions ◽  
Electric Conduction ◽  
Micro Scale ◽  
Heat Transfer Augmentation ◽  
Parallel Flows ◽  
Resultant Velocity

Electrohydrodynamic (EHD) conduction phenomenon takes advantage of the electrical Coulomb force exerted on a dielectric liquid generated by externally applied electric field. The conduction phenomenon can be applied to enhance or control mass transport and heat transfer in both terrestrial and microgravity environments with advantages of simplicity and no degradation of fluid properties for isothermal as well as non-isothermal liquids. This paper numerically studies the heat transfer augmentation of externally driven macro- and micro-scale parallel flows by means of electric conduction phenomenon. The electric conduction is generated via electrode pairs embedded against the channel wall to solely enhance the heat transfer; it is not utilized to pump the liquid. Two cases of Poiseuille and Couette parallel flows are considered where for the former, a constant external pressure gradient is applied along the channel and for the latter, the channel wall moves with a constant velocity. The electric field and electric body force distributions along with the resultant velocity fields are presented. The heat transfer enhancements are illustrated under various operating conditions for both scales.

Heat Transfer Analysis for a Small-Size Direct-Flow Coaxial Concentrating Collector

2012 ◽  
Vol 134 (4) ◽  
Author(s):  
Fabrizio Alberti ◽  
Luigi Crema ◽  
Alessandro Bozzoli
Keyword(s):  
Heat Transfer ◽  
Focal Point ◽  
Fluid Dynamic ◽  
Hot Water ◽  
Heat Transfer Analysis ◽  
Forced Flow ◽  
Heat Transfer Fluid ◽  
Small Scale ◽  
Metal Seal ◽  
Thermal Oil

A coaxial evacuated solar tube has been analyzed. The tube is included in a small-scale concentrated solar power (CSP) system, which runs a cogeneration Stirling engine unit. The engine provides electricity and at the same time generates hot water for heating and sanitary purposes, by cooling down the compression cylinder. The present work is focused on the thermodynamic characterization for a forced-flow in the coaxial evacuated tube, which can heat thermal oil up to 300 °C, when coupled with a parabolic trough collector. The single coaxial tube is 2 m long, it has one glass penetration, it is provided with a glass–metal seal and it has an absorber tube in the focal point with a diameter of 12 mm. A model based on heat transfer analysis coupled with fluid dynamic is presented and discussed. The model is then used to investigate spatial temperature profiles and thermal behaviors for the whole solar collector. It improves previous works in the field of concentrating solar collectors and covers the research in small-size concentrating system using thermal oil as heat transfer fluid.

scholarly journals Performance Evaluation of Wire Cloth Micro Heat Exchangers

Energies ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 715 ◽  
Author(s):  
Hannes Fugmann ◽  
Sebastian Martens ◽  
Richard Balzer ◽  
Martin Brenner ◽  
Lena Schnabel ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Fluid Dynamic ◽  
Relative Difference ◽  
Operating Conditions ◽  
Transfer Coefficients ◽  
Hydraulic Simulation ◽  
Pressure Drops ◽  
Wire Cloth ◽  
Good Agreement

The purpose of this study is to validate a thermal-hydraulic simulation model for a new type of heat exchanger for mass, volume, and coolant/refrigerant charge reduction. The new heat exchanger consists of tubes with diameters in the range of 1 m m and wires in the range of 100 m , woven together to form a 200 × 200 × 80 m m 3 wire cloth heat exchanger. Performance of the heat exchanger has been experimentally evaluated using water as inner and air as outer heat transfer medium. A computational thermal and fluid dynamic model has been implemented in OpenFOAM®. The model allows variation of geometry and operating conditions. The validation of the model is based on one single geometry with an opaque fabric and air-side velocities between 1 and 7 m / s . The simulated and measured pressure drops are found to be in good agreement with a relative difference of less than 16%. For the investigated cases, the effective heat transfer coefficients are in very good agreement (less than 5%) when adapting the contact resistance between tubes and wires. The numerical model describes the fluid flow and heat transfer of the tested heat exchanger with adequate precision and can be used for future wire cloth heat exchanger dimensioning for a variety of applications.

Sign in / Sign up

Export Citation Format

Share Document