Fractal Loop Heat Pipe Heat Flux and Operational Performance Testing

2009 ◽  
Author(s):  
Eric A. Silk ◽  
David Myre
Keyword(s):  
Heat Flux ◽  
Heat Pipe ◽  
Performance Testing ◽  
Working Fluid ◽  
Thermal Engineering ◽  
Loop Heat Pipe ◽  
Intimate Contact ◽  
Cross Sectional ◽  
Nasa Goddard Space ◽  
Start Ups

This study investigates heat flux performance for a LHP that includes a fractal based evaporator design. The prototype Fractal Loop Heat Pipe (FLHP) was designed and manufactured by Mikros Manufacturing Inc. and validation tested at NASA Goddard Space Flight Center’s Thermal Engineering Branch laboratory. Heat input to the FLHP was supplied via cartridge heaters mounted in a copper block. The copper heater block was placed in intimate contact with the evaporator. The evaporator had a circular cross-sectional area of 0.877 cm2. Twice distilled, deionized water was used as the working fluid. Thermal performance data was obtained for three different Condenser/Subcooler temperature combinations under degassed conditions (Psat = 25.3 kPa at 22°C). The FLHP demonstrated successful start-ups in each of the test cases performed. Test results show that the highest heat flux demonstrated was 75 W/cm2.

scholarly journals Distribution of heat flux by working fluid in loop heat pipe

2016 ◽  
Vol 114 ◽  
pp. 02081
Author(s):  
Patrik Nemec ◽  
Milan Malcho
Keyword(s):  
Heat Flux ◽  
Heat Pipe ◽  
Working Fluid ◽  
Loop Heat Pipe

Biporous Sintered Copper for Closed Loop Heat Pipe Evaporator

2005 ◽  
Author(s):  
Tadej Semenic ◽  
Ying-Yu Lin ◽  
Ivan Catton
Keyword(s):  
Heat Flux ◽  
Heat Pipe ◽  
Atmospheric Pressure ◽  
Closed Loop ◽  
Working Fluid ◽  
Loop Heat Pipe ◽  
Copper Base ◽  
Sintered Copper ◽  
Wick Structure ◽  
Heat Loads

Parameters that determine a critical heat flux (CHF) inside a biporous evaporator (wick) for a closed loop heat pipe have been studied. In a present work, a biporous wick structure was sintered from copper powder 53–63μm diameter into clusters 500–710μm diameter; the clusters were then sintered into 20mm long and 3mm wide wicks with different wick thickness on copper bases with three different lengths (5mm, 7.5mm and 10mm). Total of six wicks were made and tested. Copper base(mm) to wick thickness(mm) ratios of the wicks tested are: 5/5, 7.5/5, 10/5, 5/3, 7.5/3 and 10/1.5. Narrow (3mm) wicks with different copper base lengths allowed sidewise observation of the boiling inside the wick at different heat loads. Best-performed 10/1.5 wick, second best was 5/3 and then following 7.5/3, 5/5, 7.5/5, 10/5. Tests were run at atmospheric pressure and absolute ethanol as working fluid.

USAGE OF A DIATOMITE-CONTAINING NANOFLUID AS THE WORKING FLUID IN A WICKLESS LOOP HEAT PIPE: EXPERIMENTAL AND NUMERICAL STUDY

2018 ◽  
Vol 49 (17) ◽  
pp. 1721-1744 ◽  
Author(s):  
Adnan Sözen ◽  
Erdem Çiftçi ◽  
Selçuk Keçel ◽  
Metin Gürü ◽  
Halil Ibrahim Variyenli ◽  
...  
Keyword(s):  
Heat Pipe ◽  
Numerical Study ◽  
Working Fluid ◽  
Loop Heat Pipe

Effect of Sintering Temperature and Time in Nickel Wick for Loop Heat Pipe with Flat Evaporator

2014 ◽  
Vol 602-605 ◽  
pp. 528-532
Author(s):  
Shen Chun Wu ◽  
Chang Yu Wu ◽  
Weie Jhih Lin ◽  
Jia Ruei Chen ◽  
Yau Ming Chen
Keyword(s):  
Heat Pipe ◽  
Constant Temperature ◽  
Heat Load ◽  
Sintering Temperature ◽  
Performance Testing ◽  
Effective Porosity ◽  
Temperature Curve ◽  
Loop Heat Pipe ◽  
Maximum Heat ◽  
Load Increase

This paper specifically addresses the effect of changing the constant temperature region of the sintering temperature curve in manufacturing nickel powder capillary structure (wick) on the performance of a flat loop heat pipe (FLHP). The sintering temperature curve is composed of three regions: a region of increasing temperature, a region of constant temperature, and a region of decreasing temperature, with the sintering time and temperature in the region of constant temperature having significant effect on the permeability of the wick. In this study, for wick manufacturing the temperatures in this region tested range from 550°C to 650°C and the time from 30 minutes to 60 minutes. The properties and internal parameters of the wick are measured, and the wick is placed into FLHP for performance testing. Experimental results show that at sintering temperature of 550°C and lasting about 45 minutes, maximum heat load is 200W, minimum thermal resistance is 0.32°C/W, permeability is , porosity is 66%, effective porosity is 3.8and heat flux is around 21W/cm2; related literatures have only reported maximum heat load increase of 25%.

Device Packaging Techniques for Implementing a Novel Thermal Flux Method for Fluid Degassing and Charging of a Planar Microscale Loop Heat Pipe

2011 ◽  
Author(s):  
Navdeep S. Dhillon ◽  
Jim C. Cheng ◽  
Albert P. Pisano
Keyword(s):  
High Temperature ◽  
Heat Pipe ◽  
Thermal Flux ◽  
Anodic Bonding ◽  
Working Fluid ◽  
Loop Heat Pipe ◽  
Pressure Gradients ◽  
Flux Method ◽  
Double Compression ◽  
Plastic Package

A novel two-port thermal flux method is implemented for degassing a microscale loop heat pipe (mLHP) and charging it with a working fluid. The mLHP is fabricated on a silicon wafer using standard MEMS micro-fabrication techniques, and capped by a Pyrex wafer, using anodic bonding. For these devices, small volumes and large capillary forces render conventional vacuum pump-based methods quite impractical. Instead, we employ thermally generated pressure gradients to purge non-condensible gases from the device, by vapor convection. Three different, high-temperature-compatible, MEMS device packaging techniques have been studied and implemented, in order to evaluate their effectiveness and reliability. The first approach uses O-rings in a mechanically sealed plastic package. The second approach uses an aluminum double compression fitting assembly for alignment, and soldering for establishing the chip-to-tube interconnects. The third approach uses a high temperature epoxy to hermetically embed the device in a machined plastic base package. Using water as the working fluid, degassing and filling experiments are conducted to verify the effectiveness of the thermal flux method.

scholarly journals The Influence of Loop Heat Pipe Evaporator Porous Structure Parameters and Charge on Its Effectiveness for Ethanol and Water as Working Fluids

Materials ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 7029
Author(s):  
Krzysztof Blauciak ◽  
Pawel Szymanski ◽  
Dariusz Mikielewicz
Keyword(s):  
Porous Structure ◽  
Pore Size ◽  
Heat Pipe ◽  
Capillary Pressure ◽  
Pressure Difference ◽  
Working Fluid ◽  
Loop Heat Pipe ◽  
Working Fluids ◽  
Integral Characteristics ◽  
Sintered Stainless Steel

This paper presents the results of experiments carried out on a specially designed experimental rig designed for the study of capillary pressure generated in the Loop Heat Pipe (LHP) evaporator. The commercially available porous structure made of sintered stainless steel constitutes the wick. Three different geometries of the porous wicks were tested, featuring the pore radius of 1, 3 and 7 µm. Ethanol and water as two different working fluids were tested at three different evaporator temperatures and three different installation charges. The paper firstly presents distributions of generated pressure in the LHP, indicating that the capillary pressure difference is generated in the porous structure. When installing with a wick that has a pore size of 1 μm and water as a working fluid, the pressure difference can reach up to 2.5 kPa at the installation charge of 65 mL. When installing with a wick that has a pore size of 1 μm and ethanol as a working fluid, the pressure difference can reach up to 2.1 kPa at the installation charge of 65 mL. The integral characteristics of the LHP were developed, namely, the mass flow rate vs. applied heat flux for both fluids. The results show that water offers larger pressure differences for developing the capillary pressure effect in the installation in comparison to ethanol. Additionally, this research presents the feasibility of manufacturing inexpensive LHPs with filter medium as a wick material and its influence on the LHP’s thermal performance.

Investigation of Loop Heat Pipe Startup Using Liquid Core Visualization

2008 ◽  
Author(s):  
B. P. d’Entremont ◽  
J. M. Ochterbeck
Keyword(s):  
Heat Pipe ◽  
Liquid Core ◽  
High Heat ◽  
Working Fluid ◽  
Loop Heat Pipe ◽  
Two Phase ◽  
Buoyancy Driven Flows ◽  
Compensation Chamber ◽  
Fill Level ◽  
Heat Loads

In this investigation, a Loop Heat Pipe (LHP) evaporator has been studied using a borescope inserted through the compensation chamber into the liquid core. This minimally intrusive technique allows liquid/vapor interactions to be observed throughout the liquid core and compensation chamber. A low conductivity ceramic was used for the wick and ammonia as the working fluid. Results indicate that buoyancy driven flows, both two-phase and single-phase, play essential roles in evacuating excess heat from the core, which explains the several differences in performance between horizontal and vertical orientations of the evaporator. This study also found no discernable effect of the pre-start fill level of the compensation chamber on thermal performance during startup at moderate and high heat loads.

scholarly journals The effect of operating parameters on the heat transfer in the heat pipe

2021 ◽  
Vol 2119 (1) ◽  
pp. 012088
Author(s):  
A. A. Litvintceva ◽  
N. I. Volkov ◽  
N. I. Vorogushina ◽  
V. A. Moskovskikh ◽  
V. V. Cheverda
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Pipe ◽  
Temperature Difference ◽  
Heat Pipes ◽  
Working Fluid ◽  
Operating Parameters ◽  
Temperature Stabilization ◽  
Ir Camera ◽  
Fluid Properties

Abstract Heat pipes are a good solution for temperature stabilization, for example, of microelectronics, because these kinds of systems are without any moving parts. Experimental research of the effect of operating parameters on the heat transfer in a cylindrical heat pipe has been conducted. The effect of the working fluid properties and the porous layer thickness on the heat flux and temperature difference in the heat pipe has been investigated. The temperature field of the heat pipe has been investigated using the IR-camera and K-type thermocouples. The data obtained by IR-camera and K-type thermocouples have been compared. It is demonstrated the power transferred from the evaporator to the condenser is a linear function of the temperature difference between them.

Sign in / Sign up

Export Citation Format

Share Document