Parametric Study of the Scavenging Process in Marine Two-Stroke Diesel Engines

2015 ◽  
Author(s):  
Fredrik Herland Andersen ◽  
Stefan Mayer
Keyword(s):  
Diesel Engines ◽  
Vortex Breakdown ◽  
Initial Conditions ◽  
Combustion Process ◽  
Operating Conditions ◽  
Exhaust Valve ◽  
Delivery Ratio ◽  
Exhaust Gas ◽  
Scale Production ◽  
Cfd Model

Large commercial ships such as container vessels and bulk carriers are propelled by low-speed, uniflow scavenged two-stroke diesel engines. The integral in-cylinder process in this type of engine is the scavenging process, where the burned gas from the combustion process is evacuated through the exhaust valve and replaced with fresh air for the subsequent compression stroke. The scavenging air enters the cylinder via inlet ports which are uncovered by the piston at bottom dead center (BDC). The exhaust gas is then displaced by the fresh air. The scavenging ports are angled to introduce a swirling component to the flow. The in-cylinder swirl is beneficial for air-fuel mixture, cooling of the cylinder liner and minimizing dead zones where pockets of exhaust gas are trapped. However, a known characteristic of swirling flows is an adverse pressure gradient in the center of the flow, which might lead to a local deficit in axial velocity and the formation of central recirculation zones, known as vortex breakdown. This paper will present a CFD analysis of the scavenging process in a MAN B&W two-stroke diesel engine. The study include a parameter sweep where the operating conditions such as air amount, port timing and scavenging pressure are varied. The CFD model comprise the full geometry from scavenge receiver to exhaust receiver. Asymmetric inlet and outlet conditions is included as well as the dynamics of a moving piston and valve. Time resolved boundary conditions corresponding to measurements from an operating, full scale production, engine as well as realistic initial conditions are used in the simulations. The CFD model provides a detailed description of the in-cylinder flow from exhaust valve opening (EVO) to exhaust valve closing (EVC). The study reveals a close coupling between the volume flow (delivery ratio) and the in-cylinder bulk purity of air which appears to be independent of operating conditions, rpm, scavenge air pressure, BMEP etc. The bulk purity of air in the cylinder shows good agreement with a simple theoretical perfect displacement model.

Analysis of the Impact of Uncertainties in Inputs on CFD Predictions of Gasoline Compression Ignition

2016 ◽  
Author(s):  
Janardhan Kodavasal ◽  
Stephen Ciatti ◽  
Sibendu Som
Keyword(s):  
Cfd Simulation ◽  
Initial Conditions ◽  
Combustion Process ◽  
Chemical Kinetic ◽  
Operating Conditions ◽  
Model Parameters ◽  
Compression Ignition ◽  
Cfd Model ◽  
Kinetic Rates ◽  
The Impact

Computational fluid dynamics (CFD) is a valuable tool to gain insights into the combustion process, particularly for novel engine combustion concepts that do not have significant experimental data available. However, prediction of targets of interest from a CFD simulation can oftentimes be quite sensitive to the uncertainties in inputs to the CFD model. These uncertainties could be in the experimental boundary and initial conditions, fuel properties, CFD model constants, chemical kinetic rates, etc. In this work we isolate the effect of uncertainties in some key inputs in the form of experimental boundary conditions and CFD model parameters on combustion and emissions targets of interest for gasoline compression ignition (GCI) at two operating conditions — idle, and low-load. The uncertainties in the subset of inputs studied in this work were identified to have the greatest impact out of 34 inputs to the CFD model studied by means of a global sensitivity analysis (GSA) performed in our prior work. The goal of this study is to perform a more focused study as a follow-on to that GSA, by perturbing only a single parameter at a time.

scholarly journals Learning reference governor for cycle-to-cycle combustion control with misfire avoidance in spark-ignition engines at high exhaust gas recirculation–diluted conditions

2020 ◽  
Vol 21 (10) ◽  
pp. 1819-1834
Author(s):  
Bryan P Maldonado ◽  
Nan Li ◽  
Ilya Kolmanovsky ◽  
Anna G Stefanopoulou
Keyword(s):  
Combustion Process ◽  
Exhaust Gas Recirculation ◽  
Operating Conditions ◽  
Intake Manifold ◽  
Exhaust Gas ◽  
Model Free ◽  
Recirculation Rate ◽  
Valve Position ◽  
Gas Recirculation ◽  
Reference Governor

Cycle-to-cycle feedback control is employed to achieve optimal combustion phasing while maintaining high levels of exhaust gas recirculation by adjusting the spark advance and the exhaust gas recirculation valve position. The control development is based on a control-oriented model that captures the effects of throttle position, exhaust gas recirculation valve position, and spark timing on the combustion phasing. Under the assumption that in-cylinder pressure information is available, an adaptive extended Kalman filter approach is used to estimate the exhaust gas recirculation rate into the intake manifold based on combustion phasing measurements. The estimation algorithm is adaptive since the cycle-to-cycle combustion variability (output covariance) is not known a priori and changes with operating conditions. A linear quadratic regulator controller is designed to maintain optimal combustion phasing while maximizing exhaust gas recirculation levels during load transients coming from throttle tip-in and tip-out commands from the driver. During throttle tip-outs, however, a combination of a high exhaust gas recirculation rate and an overly advanced spark, product of the dynamic response of the system, generates a sequence of misfire events. In this work, an explicit reference governor is used as an add-on scheme to the closed-loop system in order to avoid the violation of the misfire limit. The reference governor is enhanced with model-free learning which enables it to avoid misfires after a learning phase. Experimental results are reported which illustrate the potential of the proposed control strategy for achieving an optimal combustion process during highly diluted conditions for improving fuel efficiency.

Diesel Engine Intake Condition Control-Oriented Models for Active Fuel Injection Profile Control

2011 ◽  
Author(s):  
Fengjun Yan ◽  
Junmin Wang
Keyword(s):  
Diesel Engine ◽  
Diesel Engines ◽  
Fuel Injection ◽  
Combustion Process ◽  
Exhaust Gas Recirculation ◽  
High Fidelity ◽  
Exhaust Gas ◽  
Engine Model ◽  
Profile Control ◽  
Gas Recirculation

Fueling control in Diesel engines is not only of significance to the combustion process in one particular cycle, but also influences the subsequent dynamics of air-path loop and combustion events, particularly when exhaust gas recirculation (EGR) is employed. To better reveal such inherently interactive relations, this paper presents a physics-based, control-oriented model describing the dynamics of the intake conditions with fuel injection profile being its input for Diesel engines equipped with EGR and turbocharging systems. The effectiveness of this model is validated by comparing the predictive results with those produced by a high-fidelity 1-D computational GT-Power engine model.

Enhanced Splash Models for High Pressure Diesel Sprays

2006 ◽  
Author(s):  
L. Allocca ◽  
L. Andreassi ◽  
S. Ubertini
Keyword(s):  
Diesel Engines ◽  
Second Harmonic ◽  
Laser Sheet ◽  
Combustion Process ◽  
Numerical Data ◽  
Ccd Camera ◽  
Operating Conditions ◽  
Injection System ◽  
Correct Operation ◽  
Common Rail Injection System

Mixture preparation is a crucial aspect for the correct operation of modern DI Diesel engines as it greatly influences and alters the combustion process and therefore, the exhaust emissions. The complete comprehension of the spray impingement phenomenon is a quite complete task and to completely exploit the phenomenon a mixed numerical-experimental approach has to be considered. On the modeling side, several studies can be found in the scientific literature but only in the last years complete multidimensional modeling has been developed and applied to engine simulations. Among the models available in literature, in this paper, the models by Bai and Gosman [1] and by Lee et al. [2, 3] have been selected and implemented in the KIVA-3V code. On the experimental side, the behavior of a Diesel impinging spray emerging from a common rail injection system (injection pressures of 80 MPa and 120 MPa) has been analysed. The impinging spray has been lightened by a pulsed laser sheet generated from the second harmonic of a Nd-YAG laser. The images have been acquired by a CCD camera at different times from the start of injection (SOI). Digital image processing software has enabled to extract the characteristic parameters of the impinging spray with respect to different operating conditions. The comparison of numerical and experimental data shows that both models should be modified in order to allow a proper simulation of the splash phenomena in modern Diesel engines. Then the numerical data in terms of radial growth, height and shape of the splash cloud, as predicted by modified versions of the models are compared to the experimental ones. Differences among the models are highlighted and discussed.

Set-Point Adaptation Strategy of Air Systems of Light-Duty Diesel Engines for NOx Emission Reduction Under Acceleration Conditions

2018 ◽  
Vol 140 (7) ◽  
Author(s):  
Kyunghan Min ◽  
Haksu Kim ◽  
Manbae Han ◽  
Myoungho Sunwoo
Keyword(s):  
Diesel Engines ◽  
Performance Optimization ◽  
Control Structure ◽  
Engine Performance ◽  
Optimization Method ◽  
Driving Cycle ◽  
Operating Conditions ◽  
Nox Emission ◽  
Exhaust Gas ◽  
Set Point

Modern diesel engines equip the exhaust gas recirculation (EGR) system because it can suppress NOx emissions effectively. However, since a large amount of exhaust gas might cause the degradation of drivability, the control strategy of EGR system is crucial. The conventional control structure of the EGR system uses the mass air flow (MAF) as a control indicator, and its set-point is determined from the well-calibrated look-up table (LUT). However, this control structure cannot guarantee the optimal engine performance during acceleration operating conditions because the MAF set-point is calibrated at steady operating conditions. In order to optimize the engine performance with regard to NOx emission and drivability, an optimization algorithm in a function of the intake oxygen fraction (IOF) is proposed because the IOF directly affects the combustion and engine emissions. Using the NOx and drivability models, the cost function for the performance optimization is designed and the optimal value of the IOF is determined. Then, the MAF set-point is adjusted to trace the optimal IOF under engine acceleration conditions. The proposed algorithm is validated through scheduled engine speeds and loads to simulate the extra-urban driving cycle of the European driving cycle. As validation results, the MAF is controlled to trace the optimal IOF from the optimization method. Consequently, the NOx emission is substantially reduced during acceleration operating conditions without the degradation of drivability.

Enhancement of the combustion process in dual-fuel engines at part loads using exhaust gas recirculation

2007 ◽  
Vol 221 (7) ◽  
pp. 877-888 ◽  
Author(s):  
V Pirouzpanah ◽  
R Khoshbakhti Saray
Keyword(s):  
Chemical Kinetics ◽  
Combustion Process ◽  
Exhaust Gas Recirculation ◽  
Operating Conditions ◽  
Combustion Model ◽  
Dual Fuel ◽  
Exhaust Gas ◽  
Performance And Emission ◽  
Dual Fuel Engines ◽  
Gas Recirculation

Dual-fuel engines at part loads inevitably suffer from lower thermal efficiency and higher carbon monoxide and unburned fuel emission. The present work was carried out to investigate the combustion characteristics of a dual-fuel (diesel-gas) engine at part loads, using a single-zone combustion model with detailed chemical kinetics for combustion of natural gas fuel. The authors have developed software in which the pilot fuel is considered as a subsidiary zone and a heat source derived from two superimposedWiebe combustion functions to account for its contribution to ignition of the gaseous fuel and the rest of the total released energy. The chemical kinetics mechanism consists of 112 reactions with 34 species. This quasi-two-zone combustion model is able to establish the development of the combustion process with time and the associated important operating parameters, such as pressure, temperature, heat release rate (HRR), and species concentration. Therefore, this paper describes an attempt to investigate the combustion phenomenon at part loads and using hot exhaust gas recirculation (EGR) to improve the above-mentioned drawbacks and problems. By employing this technique, it is found that lower percentages of EGR and allowance for its thermal and radical effects have a positive influence on performance and emission parameters of dual-fuel engines at part loads. Predicted values show good agreement with corresponding experimental values under special engine operating conditions (quarter-load, 1400 r/min). Implications are discussed in detail.

An Investigation of the Sources of Blowby in Single-Cylinder Supercharged Diesel Engines

1978 ◽  
Vol 192 (1) ◽  
pp. 39-48 ◽  
Author(s):  
B. Bull ◽  
M. A. Voisey
Keyword(s):  
Carbon Dioxide ◽  
Diesel Engines ◽  
Piston Ring ◽  
Carbon Dioxide Concentration ◽  
Operating Conditions ◽  
Exhaust Valve ◽  
Simple Method ◽  
Single Cylinder ◽  
Carbon Dioxide Concentrations ◽  
Wide Range

Measurements of carbon dioxide concentrations in the exhaust and in the crankcase of two different types of single-cylinder, supercharged diesel engines have been used to determine the amount of exhaust gas reaching the crankcase as piston ring blowby and as leakage through the exhaust valve stem-to-guide clearance. Over a wide range of operating conditions in both engines the carbon dioxide concentration was found to be more dependent on engine fuelling rate per hour than on fuel input per stroke. It was established that blowby through the exhaust valve guide was a major contributor to crankcase contamination. A simple method has been devised, requiring only minor modifications to the engine, that permits the blowby through the piston ring pack and the exhaust valve guides to be determined separately in turbocharged production engines.

A New Predictive ID Model for Advanced High Speed Direct Injection Diesel Engines

2004 ◽  
Author(s):  
Lurun Zhong ◽  
Naeim A. Henein ◽  
Walter Bryzik
Keyword(s):  
Diesel Engines ◽  
High Speed ◽  
Direct Injection ◽  
Combustion Process ◽  
Operating Conditions ◽  
Injection System ◽  
Injection Timing ◽  
Common Rail Injection System ◽  
Common Rail Injection ◽  
Starting Conditions

Advance high speed direct injection diesel engines apply high injection pressures, exhaust gas recirculation (EGR), injection timing and swirl ratios to control the combustion process in order to meet the strict emission standards. All these parameters affect, in different ways, the ignition delay (ID) which has an impact on premixed, mixing controlled and diffusion controlled combustion fractions and the resulting engine-out emissions. In this study, the authors derive a new correlation to predict the ID under the different operating conditions in advanced diesel engines. The model results are validated by experimental data in a single-cylinder, direct injection diesel engine equipped with a common rail injection system at different speeds, loads, EGR ratios and swirl ratios. Also, the model is used to predict the performance of two other diesel engines under cold starting conditions.

Multi-zone reaction-based modeling of combustion for multiple-injection diesel engines

2018 ◽  
Vol 21 (6) ◽  
pp. 1012-1025 ◽  
Author(s):  
Yifan Men ◽  
Ibrahim Haskara ◽  
Guoming Zhu
Keyword(s):  
Diesel Engines ◽  
Exhaust Gas Recirculation ◽  
Operating Conditions ◽  
Computational Time ◽  
Zone Model ◽  
Exhaust Gas ◽  
Cylinder Pressure ◽  
Multiple Injections ◽  
Burn Rate ◽  
Gas Recirculation

As the requirements for performance and restrictions on emissions become stringent, diesel engines are equipped with advanced air, fuel, exhaust gas recirculation techniques, and associated control strategies, making them incredibly complex systems. To enable model-based engine control, control-oriented combustion models, including Wiebe-based and single-zone reaction-based models, have been developed to predict engine burn rate or in-cylinder pressure. Despite model simplicity, they are not suitable for engines operating outside the normal range because of the large error beyond calibrated region with extremely high calibration effort. The purpose of this article is to obtain a parametric understanding of diesel combustion by developing a physics-based model which can predict the combustion metrics, such as in-cylinder pressure, burn rate, and indicated mean effective pressure accurately, over a wide range of operating conditions, especially with multiple injections. In the proposed model, it is assumed that engine cylinder is divided into three zones: a fuel zone, a reaction zone, and an unmixed zone. The formulation of reaction and unmixed zones is based on the reaction-based modeling methodology, where the interaction between them is governed by Fick’s law of diffusion. The fuel zone is formulated as a virtual zone, which only accounts for mass and heat transfer associated with fuel injection and evaporation. The model is validated using test data under different speed and load conditions, with multiple injections and exhaust gas recirculation rates. It is shown that the multi-zone model outperformed the single-zone model in in-cylinder pressure prediction and calibration effort with a mild penalty in computational time.

Sign in / Sign up

Export Citation Format

Share Document